Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Dynamic Pressure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Relating Hydro–Mechanical and Elastodynamic Properties of Dynamically Stressed Tensile–Fractured Rock in Relation to Applied Normal Stress, Fracture Aperture, and Contact Area

We exploit nonlinear elastodynamic properties of fractured rock to probe the micro-scale mechanics of fractures and understand the relation between fluid transport and fracture aperture under dynamic stressing. Experiments were conducted on rough, tensile-fractured Westerly granite subject to triaxial stresses. We measure fracture permeability for steady-state fluid flow with deionized water. Pore pressure oscillations are applied at amplitudes ranging from 0.2 to 1 MPa at 1 Hz frequency. During dynamic stressing we transmit ultrasonic signals through the fracture using an array of piezoelectric transducers (PZTs) to monitor evolution of interface properties. We examine the influence of fracture aperture and contact area by conducting measurements at effective normal stresses of 10–20 MPa. Additionally, the evolution of contact area with stress is characterized using pressure sensitive film. These experiments are conducted separately with the same fracture and map contact area at stresses from 9 to 21 MPa. The measurements are a proxy for “true” contact area for the fracture surface and we relate them to elastic properties using the calculated PZT sensor footprints via numerical modeling of Fresnel zones. We compare the elastodynamic response of the fracture using the stress-induced changes in ultrasonic wave velocities for transmitter-receiver pairs to image spatial variations in contact properties. We show that nonlinear elasticity and permeability enhancement decrease with increasing normal stress. Additionally, post-oscillation wave velocity and permeability exhibit quick recoveries toward pre-oscillation values. Estimates of fracture contact area (global and local) demonstrate that the elastodynamic and permeability responses are dominated by fracture topology.

58 GEOSCIENCES↗
DOE OSTI2024

Coupled Experimental/Computational Investigation of the Dynamics of Interacting Magnetized Plasmas

The interaction, or interpenetration, of magnetized plasmas of different density and/or pressure occurs in a wide variety of natural and man-made systems. Such systems include extragalactic jets propagating into the intergalactic medium, solar coronal mass ejections into background solar wind, compact toroid (CT) fueling of magnetic fusion plasmas, and jets of capsule shell impurities into DT fusion fuel, which can lead to enhanced impurity mix in inertial fusion implosions. These plasmas may take the form of jets, with open, helical magnetic structure, or plasma “bubbles” with closed magnetic fields (B-fields), such as spheromaks or CT’s. Such structures, both open and closed B-field cases, can transport heat, particles and magnetic flux or magnetic helicity into background plasma regions. For example, the origin of extragalactic magnetic fields may be due, at least in part, to transport by astrophysical jets. The goal of this proposed work was to elucidate the detailed plasma and magnetic field dynamics of high-density plasma jets (open B-field) and bubbles (closed B-field) propagating into lower density background magnetized plasma through controlled laboratory experiments and closely coupled nonlinear MHD modeling. These experiments were conducted in the HelCat (Helicon-Cathode) linear plasma device at the University of New Mexico (UNM). Plasma jets and bubbles were launched via an existing compact coaxial plasma gun, mounted on the HelCat device. This gun produced plasmas tens of cm in scale and lasting tens of microseconds, thereby allowing detailed multipoint, space- and time-resolved measurements to be made routinely. The experiments were directly modeled using the extended magnetohydrodynamic (XMHD) PERSEUS code, developed at Cornell University [23,24]. Both experimental and numerical modeling work are ongoing. The main results to date are reported here. Additional supplemental funding for one year (8/1/2019 – 7/31/2020) supported numerical investigation of photoionization processes important in many low temperature plasmas, including the HelCat device. Initial results of this modeling work is also reported.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Predicted Melt Curve and Liquid Shear Viscosity of RDX up to 30 GPa

Recent grain-scale simulations of HMX and TATB have shown that predictions for hot spot formation in high explosives are particularly sensitive to accurate determinations of the pressure-dependent melt curve and the shear viscosity of the liquid phase. These physics terms are poorly constrained beyond ambient pressure for the explosive RDX. Here we adopt an all-atom modeling approach using molecular dynamics (MD) simulations to predict the melt curve of RDX near to detonation conditions (30 GPa) and determine the shear viscosity of the liquid as a function of temperature and pressure above the melt curve. Phase-coexistence simulations were used to determine the melt curve, which is predicted to vary by almost 1100 K as the pressure increases from 0 GPa to 30 GPa. Equilibrium MD simulations and the Green-Kubo formalism were used to obtain the pressure-temperature-dependent shear viscosity. The shear viscosity of RDX is predicted to be of similar magnitude to the viscosity of TATB at low GPa-range pressures, and to be roughly an order of magnitude lower than the viscosity of HMX. The temperature dependence of the shear viscosity is Arrhenius at a given pressure, and the exponential pre-factor and activation term exhibit a strong, yet complicated, pressure dependence. An empirical pressure-temperature dependent function for RDX shear viscosity is developed that simultaneously captures a wide range of MD predictions while taking an analytic form that extrapolates smoothly beyond the fitted regime. The relative strength of the pressure and temperature dependencies of these two physics terms is found to be of similar magnitude for RDX, HMX, and TATB, which motivates incorporating these results in future RDX grain-scale modeling.

36 MATERIALS SCIENCE↗
DOE OSTI2020

RbB 3 Si 3 : An Alkali Metal Borosilicide that is Metastable and Superconducting at 1 atm

The stability, electronic structure and potential superconductivity in AB 3 Si 3 (A = Na, K, Rb, and Cs) compounds that assume the clathrate-based sodalite structure whose frameworks consists of covalent B-Si bonds is investigated via first-principles calculations. This structure type has recently been predicted in a number of high temperature superconducting hydrides, but these are only stable under megabar pressures. Herein, we predict a novel superconducting phase, RbB 3 Si 3 , that could be synthesized under pressures that are a factor of ten smaller, ~10 GPa, and quenched to atmospheric conditions. Electron-phonon coupling calculations predict that RbB 3 Si 3 possesses a superconducting critical temperature, T c , of 14 K at 1 atm. Here, the dynamic stability of RbB 3 Si 3 and CsB 3 Si 3 at ambient pressure can be explained by considering the chemical pressure exerted on the B-Si framework that is caused by the size effect of the alkali metal atom.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

A RELAP5-3D Model of the Lobo Lead Loop

The goal of our research is to build upon the capability of RELAP5-3D to model molten lead systems. Molten lead has several potential uses in future advanced reactors like the lead fast reactor or fusion reactors that utilize dual-coolant lead lithium blankets. This potential for use in future generations of reactors highlights the necessity to develop molten lead models to ensure that they can accurately predict the thermohydraulic behavior. We have developed a RELAP5-3D model of the Lobo Lead Loop facility, located at the University of New Mexico, to verify the accuracy of RELAP5-3D via comparison to existing computational fluid dynamics results and analytical calculations. It was found that RELAP5-3D accurately calculated radiative heat transfer (within < 1%) when compared to theoretical calculations. In addition, pressure drop calculations done in RELAP5-3D demonstrated reasonable agreement within 20 kPa, mostly within ~7-15%, when compared to the computational fluid dynamics model of the facility developed by the University of New Mexico, and captured the dependence of pressure drop on flow velocity accurately. Finally, a hypothetical loss of flow transient was imposed on the RELAP5-3D model to determine the feasibility of performing a similar experiment with the Lobo Lead Loop. It was found that such an experiment could be possible as the RELAP5-3D model indicated that the temperatures of the fluid would not exceed limiting temperatures of the structure (1658 K) nor the maximum temperature of the electromagnetic pump inlet (823 K). Although there is not experimental data to begin validation, the model will be readily available for future validation studies when the experimental data is generated, especially as the model continues to evolve over time. Furthermore, the results so far demonstrate a promising first step in the verification/validation of the RELAP5-3D model of the Lobo Lead Loop.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Structural uncertainty assessment for fire-engulfed objects in crosswind: Establishing credibility for a multiphysics wall-modeled large-eddy simulation paradigm

A structural uncertainty validation study for a large-scale, fire-engulfed, elevated object subjected to crosswind is presented to establish the credibility of a high-fidelity, low-Mach, turbulent reacting flow wall-modeled large-eddy simulation (WMLES) approach that includes multiphysics coupling to participating media radiation and conjugate heat transfer. To establish that WMLES can accurately predict surface quantities including drag and pressure coefficient in the low-Mach crosswind regime, a foundational elevated isothermal cylinder validation case is presented at a similar gap-to-diameter ratio of 0.25, spanning the subcritical to supercritical drag regime (Re 𝐷 = 1.1 × 10 5 and 4.3 × 10 5 , respectively). Here, this study exercised both static and dynamic coefficient LES (Smagorinsky and 𝑘 sgs ) with both local and exchange-based velocity sampling. Results showcase that the drag crisis (or the sudden drop in drag coefficient at increased Re 𝐷 ) is well captured when using an exchange-based dynamic coefficient WMLES methodology, while noting lack of mesh convergence and overall drag and pressure coefficient predictively when using a static coefficient, local velocity sampling WMLES. For the 𝒪⁡(10) m JP-8 liquid pool fire crosswind validation study presented, two experimental crosswind configurations (2 m/s and 9.5 m/s) are showcased for a fire-engulfed mock fuselage roughly 4 m in diameter. Using the best model-form practices identified in the isothermal study, dynamic coefficient 𝑘 sgs exchange-based WMLES fire validation findings demonstrate accurate peak irradiation and skin temperature predictions as a function of crosswind magnitude. Excessive yaw in the low-crosswind fuselage configuration, consistent with experimental findings, captured a significant predicted asymmetry in flame attachment and heat flux toward the downwind cylindrical cap—indicative of axial vortex structures transporting the flame along the upper and lower fuselage leeward surface. All fire mesh resolution simulations captured the experimental finding that as crosswind increased, predicted flame shape and peak irradiation magnitude onto the fuselage transitioned from a windward to a leeward cylinder location due to the migration of the upper- to lower-shear fuel/air mixing layer thereby demonstrating the novelty, significance, and credibility of this high-fidelity WMLES reacting flow framework.

Domino, Stefan Paul [Sandia National Laboratories ↗
DOE OSTI2024

Extreme compression of planetary gases: High-accuracy pressure-density measurements of hydrogen-helium mixtures above fourfold compression

Hydrogen (H 2 ) and helium (He), the most abundant elements in the universe, pose a unique challenge in measuring the equation of state of the mixture, owing to their differing physical properties. There remains a need for data with high enough precision to discriminate between existing equation of state (EOS) mix models in order to understand the internal structure of gas-giant planets. Here, we have measured the EOS of precompressed H 2 - He mixtures at conditions directly relevant to the planetary interiors using hypervelocity gas guns and Sandia’s Z machine with less than 10% uncertainty in density, enabling validation of mixture models. We precompressed 50:50 molar mixtures of H 2 -He to 0.1–0.2 GPa and directly measured particle velocity (in gas-gun experiments) and shock velocities (in Z-machine experiments). To complement the experimental efforts, we also computed the Hugoniots of precompressed H 2 -He mixtures using density-functional-theory-based molecular dynamics. Furthermore, we observe approximately 3- to 4.3-fold density compression at pressures up to 44 GPa.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Sugar loading is not required for phloem sap flow in maize plants

We report phloem transport of photoassimilates from leaves to non-photosynthetic organs, such as the root and shoot apices and reproductive organs, is crucial to plant growth and yield. For nearly 90 years, evidence has been generally consistent with the theory of a pressure-flow mechanism of phloem transport. Central to this hypothesis is the loading of osmolytes, principally sugars, into the phloem to generate the osmotic pressure that propels bulk flow. Here we used genetic and light manipulations to test whether sugar import into the phloem is required as the driving force for phloem sap flow. Using carbon-11 radiotracer, we show that a maize sucrose transporter1 (sut1) loss-of-function mutant has severely reduced export of carbon from photosynthetic leaves (only ~4% of the wild type level). Yet, the mutant remarkably maintains phloem pressure at ~100% and sap flow speeds at ~50–75% of those of wild type. Potassium (K+) abundance in the phloem was elevated in sut1 mutant leaves. Fluid dynamic modelling supports the conclusion that increased K+ loading compensated for decreased sucrose loading to maintain phloem pressure, and thereby maintained phloem transport via the pressure-flow mechanism. Furthermore, these results suggest that sap flow and transport of other phloem-mobile nutrients and signalling molecules could be regulated independently of sugar loading into the phloem, potentially influencing carbon–nutrient homoeostasis and the distribution of signalling molecules in plants encountering different environmental conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A Variable Pressure Multi-Pressure Rail System Design for Agricultural Applications

This paper presents a solution for reducing energy loss in the hydraulic control system of agricultural tractors and their implements. The solution is referred to as a multi-pressure rail (MPR) and provides power to the hydraulic functions following a pressure control logic, as opposed to the traditional flow control logic typical of hydraulic systems used in off-road vehicles. The proposed hydraulic control system allows for elimination of redundant flow control valves in the state-of-the-art system, which cause excessive throttling losses leading to poor overall energy efficiency. Related work on MPR technology targets construction vehicles, where the MPR solution can allow energy recovery during overrunning loads and better engine management. This paper alternatively addresses the case of agricultural applications where functions mostly operate under resistive load conditions with slow dynamics, which offers an opportunity to target throttle losses. For this purpose, the paper introduces a variable pressure control strategy to handle the instantaneous pressure at each rail. To develop both the controller and the hydraulic system architecture, a stationary test rig is conceived and used to validate a numerical simulation model of the MPR system and its control strategy. Particular focus is given to the dynamic behavior of the system during the switches of a function between different pressure rails, which needs to ensure reduced oscillations of the flow provided to each hydraulic function. Once validated, the simulation model is used to predict the energy savings of the MPR solution in an actual application: a 435 hp hydraulic tractor powering a 16-row planter, for which operating features during typical drive cycles were available to the authors. The results show up to 59% total power reduction at the pump shaft, corresponding to 89.8% system efficiency gain.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Kinetic Simulations of Radiative Magnetic Reconnection in the Coronae of Accreting Black Holes

We perform 2D and 3D particle-in-cell simulations of reconnection in magnetically dominated e ± plasmas subject to strong Compton cooling. Magnetic reconnection under such conditions can operate in accretion disk coronae around black holes, which produce hard X-rays through Comptonization. Our simulations show that most of the plasma in the reconnection layer is kept cold by Compton losses and locked in magnetically dominated plasmoids with a small thermal pressure. Compton drag clears cavities inside plasmoids and also affects their bulk motions. These effects, however, weakly change the reconnection rate and the plasmoid size distribution from those in nonradiative reconnection. This demonstrates that the reconnection dynamics is governed by similar magnetic stresses in both cases and weakly affected by thermal pressure. We examine the energy distribution of particles energized by radiative reconnection and observe two distinct components: (1) A mildly relativistic peak, which results from bulk motions of cooled plasmoids. This component receives most of the dissipated reconnection power and dominates the output X-ray emission. The peak has a quasi-Maxwellian shape with an effective temperature of ~100 keV. Thus, it mimics thermal Comptonization used previously to fit hard-state spectra of accreting black holes. (2) A high-energy tail, which receives ~20% of the dissipated reconnection power. It is populated by particles accelerated impulsively at X-points or "picked up" by fast outflows from X-points. The high-energy particles immediately cool, and their inverse Compton emission explains the MeV spectral tail detected in the hard state of Cyg X-1. Our first-principle simulations support magnetic reconnection as a mechanism powering hard X-ray emission from magnetically dominated regions of accreting black holes.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2020

High Vapor Pressure Deficit Decreases the Productivity and Water Use Efficiency of Rain‐Induced Pulses in Semiarid Ecosystems

Abstract Intermittent rain events drive dynamic pulses of carbon and water exchange in many arid and semiarid ecosystems. Although soil moisture is known to control these pulses, the effect of atmospheric dryness on pulses is not well documented. Here we hypothesized that vapor pressure deficit ( VPD ) modulates net ecosystem production ( NEP ) and ecosystem‐scale water use efficiency ( WUE ) during pulse events due to its effects on canopy stomatal conductance and evapotranspiration. We quantified relationships between VPD and carbon and water exchange during growing season rain events and tested their generality across four semiarid flux sites with varied vegetation in the southwest United States. Across grassland, shrubland, and savanna sites, we found that high VPD during pulses suppressed ecosystem photosynthesis and surface conductance to a greater degree than respiration or evapotranspiration, particularly when soil moisture was high. Thus, periods of high VPD were associated with a 13–64% reduction in NEP and an 11–25% decrease in WUE , relative to moderate VPD conditions. Sites dominated by shrubs with the C3 photosynthetic pathway were more sensitive to VPD than sites dominated by C4 grasses. We found that a 1 kPa increase in VPD reduced the average NEP of pulse events by 13–56%, which illustrates the potential for projected increases in atmospheric demand to reduce the net productivity of semiarid ecosystems.

Roby, Matthew C.↗
DOE OSTI2021

Operando high-pressure investigation of size-controlled CuZn catalysts for the methanol synthesis reaction

Although Cu/ZnO-based catalysts have been long used for the hydrogenation of CO 2 to methanol, open questions still remain regarding the role and the dynamic nature of the active sites formed at the metal-oxide interface. Here, we apply high-pressure operando spectroscopy methods to well-defined Cu and Cu 0.7 Zn 0.3 nanoparticles supported on ZnO/Al2O 3 , γ-Al 2 O 3 and SiO 2 to correlate their structure, composition and catalytic performance. We obtain similar activity and methanol selectivity for Cu/ZnO/Al 2 O 3 and CuZn/SiO 2 , but the methanol yield decreases with time on stream for the latter sample. Operando X-ray absorption spectroscopy data reveal the formation of reduced Zn species coexisting with ZnO on CuZn/SiO 2 . Near-ambient pressure X-ray photoelectron spectroscopy shows Zn surface segregation and the formation of a ZnO-rich shell on CuZn/SiO 2 . In this work we demonstrate the beneficial effect of Zn, even in diluted form, and highlight the influence of the oxide support and the Cu-Zn interface in the reactivity.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Numerical Analysis and Flow Induced Vibration Studies in Pressurized Helium Gas Cooling Channels

Los Alamos National Laboratory (LANL) is working with NorthStar Medical Radioisotopes (NMR) on their efforts to produce Mo-99 from the irradiation of Mo-100 targets. The NMR target consists of an Inconel window that allows the electron beam to penetrate and irradiate a stack of Mo-100 discs. The irradiation process generates large amounts of heat and is cooled using pressurized helium gas flowing at 400 g/s. LANL provides both numerical analysis support and experimental support. Computational fluid dynamics (CFD) simulations for both 300 g/s and 400 g/s are performed on the NMR target to analyze the helium flow through the NMR system. The pressure drop, the mass flow rate through each of the disc and window channels and the force applied on the first disc are some of the quantities estimated using CFD. These results will be combined with Monte Carlo N-Particle (MCNP) estimates of heat flux into the system from the electron beam to perform conjugate heat transfer analysis (CHT). The experiments presented in this report focus on the effect of the flow induced vibrations from helium flowing through the coolant gaps between the discs. There is concern that the flow induced vibrations may lead to excessive mass loss of the enriched Mo-100 discs, and the goal would be to mitigate the mass loss. This work presents benchtop tests of flow through a subset of the target stack which involves high speed imaging and displacement measurements used to estimate disc vibration, as well as mass loss.

42 ENGINEERING↗
DOE OSTI2022

Hydrogen solubility in FeSi alloy phases at high pressures and temperatures

Abstract Light elements alloying with metallic Fe can change the properties and therefore play a key role in the structure and dynamics of planetary cores. Hydrogen and silicon are possible light elements in the rocky planets’ cores. However, hydrogen storage in Fe-Si alloy systems remains unclear at high pressures and high temperatures because of experimental difficulties. Taking advantage of pulsed laser heating combined with high-energy synchrotron X-ray diffraction, we studied reactions between FeSi and H in laser-heated diamond-anvil cells (LHDACs) up to 61.9 GPa and 3500 K. We found that under H-saturated conditions the amount of H alloying with FeSi (0.3 and <0.1 wt% for the B20 and B2 structures, respectively) is much smaller than that in pure Fe metal (>1.8 wt%). Our experiments also suggest that H remains in the crystal structure of FeSi alloy when recovered to 1 bar. Further density functional theory (DFT) calculations indicate that the low-H solubility likely results from the highly distorted interstitial sites in the B20 and B2 structures, which are not favorable for H incorporation. The recovery of H in the B20 FeSi crystal structure at ambient conditions could open up possibilities to understand geochemical behaviors of H during core formation in future experiments. The low-H content in FeSi alloys suggests that if a planetary core is Si-rich, Si can limit the ingassing of H into the Fe-rich core.

Geochemistry & Geophysics↗
DOE OSTI2022

Materials under high pressure: a chemical perspective

At high pressure, the typical behavior of elements dictated by the periodic table, including oxidation numbers, stoichiometries in compounds, and reactivity, to name but a few, is altered dramatically. As pressure is applied, the energetic ordering of atomic orbitals shifts, allowing core orbitals to become chemically active, atypical electron congurations to occur, and in some cases,non-atom-centered orbitals to form in the interstices of solid structures. Strange stoichiometries, structures, and bonding motifs result. Crystal structure prediction tools, not burdened by preconceived notions about structural chemistry learned at atmospheric pressure, have been applied to great success to explore phase diagrams at high pressure, identifying novel structures in diverse chemical systems. Several of these phases have been subsequently synthesized. Experimentally, access to high-pressure regimes has been bolstered by advances in diamond anvil cell and dynamic com- pression techniques. Here, the joint efforts of experiment and theory have led to startling success stories in the realm of high-temperature superconductivity, identifying many novel phases (some of which have been synthesized) whose superconducting transition approaches room temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2024

High-Pressure and Temperature Effects on the Clustering Ability of Monohydroxy Alcohols

This study examined the clustering behavior of monohydroxy alcohols, where hydrogen-bonded clusters of up to a hundred molecules on the nanoscale can form. By performing X-ray diffraction experiments at different temperatures and under high pressure, we investigated how these conditions affect the ability of alcohols to form clusters. The pioneering high-pressure experiment performed on liquid alcohols contributes to the emerging knowledge in this field. Implementation of molecular dynamics simulations yielded excellent agreement with the experimental results, enabling the analysis of theoretical models. Here we show that at the same global density achieved either by alteration of pressure or temperature, the local aggregation of molecules at the nanoscale may significantly differ. Surprisingly, high pressure not only promotes the formation of hydrogen-bonded clusters but also induces the serious reorganization of molecules. This research represents a milestone in understanding association under extreme thermodynamic conditions in other hydrogen bonding systems such as water.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Real Time 3D Observations of Portland Cement Carbonation at CO2 Storage Conditions

Depleted oil reservoirs are considered a viable solution to the global challenge of CO 2 storage. A key concern is whether the wells can be suitably sealed with cement to hinder the escape of CO 2 . Under reservoir conditions, CO 2 is in its supercritical state, and the high pressures and temperatures involved make real-time microscopic observations of cement degradation experimentally challenging. Here, we present an in situ 3D dynamic X-ray micro computed tomography (μ-CT) study of well cement carbonation at realistic reservoir stress, pore-pressure, and temperature conditions. The high-resolution time-lapse 3D images allow monitoring the progress of reaction fronts in Portland cement, including density changes, sample deformation, and mineral precipitation and dissolution. By switching between flow and nonflow conditions of CO 2 -saturated water through cement, we were able to delineate regimes dominated by calcium carbonate precipitation and dissolution. For the first time, we demonstrate experimentally the impact of the flow history on CO 2 leakage risk for cement plugging. In-situ μ-CT experiments combined with geochemical modeling provide unique insight into the interactions between CO 2 and cement, potentially helping in assessing the risks of CO 2 storage in geological reservoirs.

58 GEOSCIENCES↗
DOE OSTI2021

Formation of edge pressure pedestal and reversed magnetic shear due to toroidal rotation in a tokamak equilibrium

Toroidal rotation is well known to play significant roles in the edge transport and L-H transition dynamics of tokamaks. Our recent calculation finds that a sufficiently strong localized toroidal rotation can directly bring out the formation of edge pressure pedestal with reversed magnetic shear that is reminiscent of an H-mode plasma, purely through the effects of toroidal rotation on the tokamak MHD equilibrium itself. In particular, the enhanced edge toroidal rotation enables a substantial peaking of the parallel current profile near edge in higher β regimes, which leads to the flattening or reversal of the local q (safety factor) profile. Here the formation of pressure pedestal along with the reversed magnetic shear region is shown to be the natural outcome of the MHD tokamak equilibrium in a self-consistent response to the presence of a localized toroidal rotation typically observed in H-mode or QH-mode.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗