Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Ductility”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

The effect of loading direction on the fracture behaviors of cortical bone at a dynamic loading rate

Here, the dynamic cracking processes in porcine cortical bone were visualized in real-time using the high-speed synchrotron X-ray phase-contrast imaging (PCI) technique in three osteon orientations: in-plane transverse, out-of-plane transverse and in-plane longitudinal. The dynamic flexural loading applied on the pre-notched bone specimens was introduced by a modified Kolsky compression bar. High-speed X-ray images of the entire loading events were documented with a high-speed camera. Three-dimensional X-ray micro-computed tomography was conducted to examine the intact microstructures and obtain the basic material properties of the bone material used for mechanical characterizations. The onset location, where crack initiated, and the subsequent direction, along which the incipient crack propagated, were measured quantitatively using the high-speed X-ray images and the latter was found dependent on the osteon direction significantly. The crack propagation velocities were dependent on crack extension over the entire crack path significantly for all the three directions while the initial velocity for in-plane longitudinal direction was lower than the other two directions. Straight-through crack paths were observed for in-plane longitudinal specimens while the cracks were deflected and twisted in the in-plane transverse direction. For out-of-plane transverse direction, the cracks follow paths with tortuosity fall in between the other two directions, showing a mixed mode of fractures of the former two extreme cases. The toughening mechanisms, visualized by the high-speed X-ray images, and the corresponding fracture toughness, evaluated in terms of fracture initiation toughness and crack growth resistance curve (R-curve), were also found significantly different among the three osteon directions, suggesting an overall transition from brittle to ductile-like fracture behaviors at the dynamic displacement rate (5.4 m/s) as the osteon orientation varies from in-plane longitudinal to out-of-plane transverse, and to in-plane transverse eventually.

42 ENGINEERING↗
DOE OSTI2025

Inference of phase field fracture models

The phase field approach to modeling fracture uses a diffuse damage field to represent cracks. This representation mollifies singularities that arise in computations with sharp interface models and some of the resultant difficulties in the mathematical and numerical treatment of fracture. Phase field fracture models have proven effective at representing crack propagation, branching, and merging. Specific formulations, beginning with brittle fracture, have also been shown to converge to classical solutions. Extensions to cover the range of material failure, including ductile and cohesive fracture, lead to an array of possible models. There exists a large body of literature focusing on this class of models and on the impact of model form on the predicted crack evolution. However, there have not been systematic studies into how optimal models may be chosen. Here, we take a first step in this direction by developing formal methods for identification of the best parsimonious model of phase field fracture given full-field data on the damage and deformation fields. We consider some of the main models that have been used for the degradation of elastic response due to damage and its propagation. Our approach builds upon Variational System Identification (VSI), a weak form variant of the Sparse Identification of Nonlinear Dynamics (SINDy). Furthermore, in this first communication we focus on synthetically generated data but we also consider central issues associated with the use of experimental full-field data, such as data sparsity and noise.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

High-entropy materials: fundamentals and applications

Metallic high-entropy materials (HEMs), also known as high-entropy alloys (HEAs), are an exotic class of materials that possess desirable properties, such as exceptional strength and ductility, high wear resistance, and corrosion resistance. Due to these positive attributes, HEAs have been proposed for use in the automotive and aerospace industries, nuclear reactor technology, and the biomedical field. In terms of composition, HEAs contain five or more elements in amounts ranging from 5 to 35 atomic percent (at.%) each, resulting in a vast compositional space that is still mainly unexplored to this day. More recently, the field of HEMs has broadened to include materials such as polymers and ceramics.

36 MATERIALS SCIENCE↗
DOE OSTI2023

In-situ investigation of strengthening and strain hardening mechanisms of Cu-added medium-Mn steels by synchrotron-based high-energy X-ray diffraction

A novel Cu-added medium-Mn steel with a chemical composition of Fe–0.27C–9.1Mn–1.86Al–3.3Cu (wt.%) was designed and subjected to intercritical annealing (IA) temperature range from 620 °C to 680 °C for 1 h. The ultimate tensile strength (UTS) increases and the yielding strength (YS) decreases with the IA temperature increasing. The YS of 824 MPa, UTS of 1222 MPa, total elongation (TE) of 55%, and product of strength and elongation (PSE) of 67.2 GPa·% are achieved after IA at 660 °C. Transmission electron microscopy confirmed that Cu-rich nanoparticles precipitate in the ferrite. The in-situ high-energy X-ray diffraction (HE-XRD) experiments show that at the beginning of plastic deformation, both austenite and ferrite bear the applied load. The load is mainly undertaken by martensite with effective transformation-induced plasticity (TRIP) effect triggered. The YS of ferrite is significantly higher than that of austenite. The individual contribution of solid solution strengthening, grain refinement strengthening, dislocation strengthening, and precipitation strengthening in ferrite and austenite is analyzed. The discrepancy between the YS of ferrite and austenite is mainly attributed to the precipitation strengthening due to the Cu-rich nanoparticles precipitation. The moderate mechanical stability and the collaboration of TRIP and twinning-induced plasticity (TWIP) effects of austenite contributed to the enhanced strain hardening capability and resulted in large ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Binder-jetted AISI M2 tool steel during hot isostatic pressing: Densification and carbide transformation

Binder jetting (BJ) enables fabrication of complex components from high-alloy steels such as AISI M2; however, residual porosity after sintering limits mechanical performance. This study investigates the coupled effects of binder chemistry, sintering conditions, cooling rate, and subsequent hot isostatic pressing (HIP) on densification, microstructure, and mechanical response in binder-jetted M2 tool steel. HIP increased relative density from ∼93 to 95% to >99% and improved compressive strength by ∼40-70%. Densification was governed by initial pore morphology, where closed porosity was effectively eliminated, while interconnected porosity limited full consolidation. Microstructural analysis (XRD, EBSD, SEM) shows that HIP promotes dissolution of metastable carbides and redistribution of alloying elements (W, Mo, V), transforming heterogeneous carbide networks into finer and more uniformly distributed M 2 C, MC, and M 6 C phases through diffusion-assisted homogenization. Among the investigated conditions, the FluidFuse binder combined with sintering at 1270 °C for 60 min and furnace cooling produced the most balanced response, achieving ∼99.7% density, ∼855 HV hardness, ∼4130 MPa compressive strength, and ∼24% strain. In contrast, higher sintering temperatures promoted carbide coarsening, reducing ductility despite high density. HIP reduces microstructural heterogeneity and drives the system toward a near-equilibrium state with reduced sensitivity to prior processing history. A comparative assessment with conventional and additive manufacturing routes (LPBF, DED, EBM, FFF) shows that the BJ-HIP approach achieves competitive densification and mechanical performance. These findings provide a mechanistic basis for controlling densification and microstructure in high-alloy steels processed via BJAM.

AISI M2 tool steel↗
DOE OSTI2021

A constitutive model incorporating grain refinement strengthening on metallic alloys

Surface nano-crystallization techniques have been recently developed as one of the most efficient ways to optimize materials’ structure, and therefore develop the local and global mechanical behavior as to increase strength without compromising ductility. Here, in this work, we present a constitutive model incorporating grain refinement hardening to simulate the nano-crystallization technique, specifically, surface mechanical attrition treatment. The computation is implemented using user-defined VUMAT subroutines. As an example of its application, a geometry model with full coverage of random impacts are employed. The results show that the model has rather precise predictability of grain size evolution during plastic deformation. The readily embedded with a computational code of material dynamics enables this novel model to be a promising tool to study the dynamic evolution of microstructures under plastic deformation.

36 MATERIALS SCIENCE↗
DOE OSTI2022

High-pressure deformation of metallic glass nanoparticles

Here, the atomistic structure of metallic glasses is closely related to properties such as strength and ductility. Here, Ni 1-x B x metallic glass nanoparticles of two different sizes are compressed under quasi-hydrostatic high-pressure conditions in order to understand structural changes under stress. The structural changes in the nanoparticles were tracked using in situ high-pressure X-ray diffraction (XRD). The ambient pressure pair distribution functions generated from XRD showed that the smaller sized nanoparticles had a more compact amorphous structure with lower coordination number. XRD showed that the amorphous structure was stable up to the maximum pressures achieved. The bulk modulus of the smaller and larger sized nanoparticles was found to be 208 GPa and 178 GPa, respectively. This size-dependent high-pressure behavior was related to compositional differences between the nanoparticles. These results show that Ni 1-x B x metallic glass nanoparticles are highly stable under pressure, which could enable their use as inclusions in metal or ceramic matrix composites.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Non-linear elastic-plastic behavior of the invert glass lithium phosphorous oxynitride (LiPON)

Micro and nano-scale mechanical behavior of network/ionic glasses is dictated by their composition and the number of constraints per structural unit. From this perspective, the glass LiPON presents the opportunity for enhancement of the microscale ductility due to its rather unconstrained orthophosphate structure. Here, we use instrumented nanoindentation with different tip geometries to investigate the mechanical response of LiPON glass. The results reveal that the elastic modulus of LiPON is not constant and depends on pressure. With the method utilizing spherical nanoindentation and continuous stiffness measurement (CSM) we determine the yield point of LiPON. We propose the Drucker-Prager type of yield criterion for LiPON and estimate its yield stress in compression as 2.4 GPa. There exists another stress threshold, however, around 490 MPa, at which the elastic deformation becomes non-linear, and this can be mistaken for the yield stress.

Constitutive model↗
DOE OSTI2020

On the use of charged particles to characterize precipitation in irradiated reactor pressure vessel steels with a wide range of compositions

Nuclear reactor lifetimes may be limited by nano-scale Cu-Mn-Ni-Si precipitates (CRPs and MNSPs) that form under neutron irradiation (NI) of pressure vessel (RPV) steels, resulting in hardening and ductile to brittle transition temperature increases (embrittlement). Physical models of embrittlement must be based on characterization of precipitation as a function of the combination of metallurgical and irradiation variables. Here we focus on rapid and convenient charged particle irradiations (CPI) to both: a) compare to precipitates formed in NI; and, b) use CPI to efficiently explore precipitation in steels with a very wide range of compositions. Atom probe tomography (APT) comparisons show NI and CPI for similar bulk steel solute contents yield nearly the same precipitate compositions, albeit with some differences in their number density, size and volume fraction (f) dose (dpa) dependence. Yet, the overall precipitate evolutions are very similar. Advanced high Ni (>3 wt%) RPV steels, with superior unirradiated properties, were also investigated at high CPI dpa. For typical Mn contents, MNSPs have Ni 16 Mn 6 Si 7 or Ni 3 Mn 2 Si phase type compositions, with f values that are close to the equilibrium phase separated values. In contrast, in steels with very low Mn and high Ni, Ni 2-3 Si silicide phase type precipitate compositions are observed; and when Ni is low, the precipitate compositions are close to the MnSi phase field. Low Mn significantly reduces, but does not eliminate, precipitation in high Ni steels. A comparison of dispersed barrier model predictions with measured hardening data suggests that the Ni-Si dominated precipitates are weaker dislocation obstacles than the G phase type MNSPs.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Evaluation of the effects of neutron irradiation on first-generation corrosion mitigation coatings on SiC for accident-tolerant fuel cladding

In this work, high purity SiC and SiC/SiC composites coated with commercial TiN, Cr, CrN, or CrN/Cr multilayer coatings were irradiated in Ar or flowing PWR water in the Massachusetts Institute of Technology Nuclear Reactor Laboratory (MITR). Irradiation in Ar was performed in the core. In the water environment, identical samples were placed in one of three different locations: in-core, providing exposure to neutron damage and radiolysis-affected water; above-core, where samples were exposed to radiolysis-affected water but not neutron damage, or outside of the core, where samples were exposed to the coolant water without the effects of radiation. Radiation in Ar revealed significant cracking of all but the TiN coatings, attributed to differential swelling between the coating and substrate. Lattice swelling was not observed in any of the coatings, but 0.2% void swelling was observed in the Cr coating. All of the coatings failed during water exposures in the core. Likewise, CrN/Cr spalled in each condition. Cr was protective, except under radiation damage as a result of cracking, and TiN severely degraded in the core with no coating was found following exposure. A SiC/coating ATF cladding system is anticipated to perform adequately following improvements in coating ductility and purity.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Irradiation Damages of Structural Materials under Different Irradiation Environments

For the advancement and development of nuclear systems used in heavy irradiation environments such as fusion DEMO reactors, fission reactors, fast reactors, and accelerator driven target systems, it is necessary to fully understand the changes of mechanical properties and the other properties of the materials induced by irradiation and to clarify the synergistic effect of displacement damage and helium generation. In this study the mechanical property changes and microstructural development induce by displacement damage and helium production have been mainly examined in austenitic stainless steels, 316FR and type304, and ferritic/martensitic steel, HCM12A, irradiated at around 550oC in JRR-3M reactor and/or JOYO fast reactor. At 550°C, 316FR steel was superior to 304 steel in terms of the amount of ductility and strength with respect to irradiation resistance. It is noteworthy that at 550 °C as well as room temperature, the higher fracture strength of the 316FR steels is a remarkable result. It is found that helium atoms strongly influenced on creep lifetime of the irradiated austenitic stainless steel, 316FR. It was found that the ratio of creep rupture time is slightly lower than the lower limit of previous study’s Miyaji and co-workers in the region from 0.01 appm to 1 appm. It is also found that the lower limit of reduction ratio of creep rupture time (irradiation specimen to unirradiation one) does not decrease linearly with the helium production above 10 appm up to about 33 appm. dpa enhanced the reduction of creep lifetime. Recent R&D of high-energy accelerator driven target systems used under heavy irradiation environment is also introduced and discussed for high radiation resistance materials such as Ti alloys with very high number density of nano size precipitate, which have been studying under RaDIATE collaboration, from points of view of irradiation damage and materials development.

radiation damage, structural alloys, neutron irrad↗
DOE OSTI2020

High Flux Helium Irradiation of Dispersion-Strengthened Tungsten Alloys and Effects of Heavy Metal Impurity Layer Deposition

Tungsten has been chosen as the plasma-facing material (PFM) for the divertor region in ITER and also a candidate PFM for future plasma-burning nuclear fusion reactors. During fusion device operation, PFMs will be exposed to low-energy He irradiation at high temperatures, resulting in sub-surface bubbles and surface morphology changes such as pores and fuzz. Carbide dispersion-strengthened W materials may enhance the ductility of W, but their behavior under high flux He irradiation remains unclear. In this work, the response of dispersion-strengthened tungsten materials to high flux, low energy He irradiation at high temperature is examined. Tungsten alloyed with 1, 5, or 10 wt. % tantalum carbide or titanium carbide exposed to these conditions result in surface pores, coral-like feature growth and sub-surface helium bubbles. Reactor-relevant helium irradiation (5 x 10 26 m -2 fluence) combined with high powered laser pulses to simulate off-normal reactor events does not significantly alter the surface morphology, as the surface nanostructures appear stable and cracks are only observed on a localized region of one sample. However, specimens show the development of an impurity layer on the surface, likely impurity deposition from the sample holder during irradiation, resulting in a mixed material layer on the surface. Helium bubbles exist in this impurity layer, and obscure conclusions about helium interactions with the carbide dispersoids. Nonetheless, it is clear that the dispersoid microstructure limits He bubble formation and subsequent surface nanostructuring, attributed to the dispersoid composition.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Characterization of mechanical properties and deformation behavior of highly irradiated 316L stainless steel from target modules at the Spallation Neutron Source using digital image correlation analysis

Tensile specimens with irradiation doses ranging from approximately 0.7 to 7.6 displacements per atom (dpa) were fabricated from 316L samples removed from Spallation Neutron Source (SNS) target vessels after service. Tensile tests were performed in conjunction with digital image correlation (DIC) characterization, which permitted detailed analysis of the strain distribution and deformation behavior of the specimen gauge sections during testing. The results show, while considerable hardening (500–700 MPa increase in yield strength) occurred in the 316L SNS target material with increasing dose, appreciable ductility (19–23% total elongation) remained in the material after irradiation to 7.6 dpa in the mixed neutron/proton environment of the SNS target region. The DIC data showed the strain distribution and deformation behavior of all irradiated specimens were nonuniform during testing. Strain localization in the form of deformation bands or “hotspots” was observed during testing, and in some specimens, the bands propagated as deformation waves along the gauge section. The “traveling wave” deformation behavior affected the amount of elongation each specimen achieved, and the scatter in the elongation data was attributed to the large variation in deformation behavior observed among different specimens. Bands of localized strain, or deformation bands, oriented at specific angles were observed in two-dimensional plots of the strain distribution in the gauge sections of some specimens. Overall, this paper describes the experimental procedures, results, and deformation behavior of tensile specimens from SNS targets after service and illustrates the value of DIC characterization during tensile testing of irradiated materials.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Quantifying the effect of hydride microstructure on zirconium alloys embrittlement using image analysis

Since hydride microstructure can significantly influence Zr alloy nuclear fuel cladding’s ductility, a new metric has been developed to quantify hydride microstructure in 2D micrographs and relate it to crack propagation. As cladding failure usually results from a hoop stress, this new metric, called the Radial Hydride Continuous Path (RHCP), is based on quantifying the continuity of brittle hydride particles along the radial direction of the cladding tube. Compared to previous metrics, this approach more closely relates to the propensity of a crack to propagate radially through the cladding tube thickness. The RHCP takes into account hydride length, orientation, and connectivity to choose the optimal path for crack propagation through the cladding thickness. The RHCP can therefore be more closely linked to hydride embrittlement of the Zr alloy material, thus creating a relationship between material structure, properties, and performance. The new definition, along with previously proposed metrics such as the Radial Hydride Fraction (RHF), the Hydride Continuity Coefficient (HCC), and the Radial Hydride Continuity Factor (RHCF), have been implemented and automated in MATLAB. These codes are made available with this publication as supplementary materials. These metrics were verified by comparing their predictions of hydride morphology against expected values in simple cases, and the implementation of the new metric was validated by comparing its predictions with manual measurements of hydride microstructure performed on ImageJ. The RHCP was also validated against experimental measurements of fracture behavior and it was shown to correlate with cladding failure better than previous metrics. The information provided by these metrics will help accurately assess cladding integrity during operation, transportation, and storage.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Creep behavior of 316 L stainless steel manufactured by laser powder bed fusion

Additive manufacturing as a new processing technique can produce unique microstructure that is difficult to achieve using conventional techniques. Here, we have investigated the creep behavior of 316 L stainless steel produced by a laser powder bed fusion process at temperatures of 550, 600 and 650 °C and stresses between 175 and 300 MPa. We found that additively-manufactured 316 L stainless steel had a higher stress dependence of the minimum creep rate than conventionally-made Type 316 SS, which could be attributed to the dislocation cell structure resulting from the printing process. The dislocation cell structure was unstable under creep, evolving into a uniform dislocation structure under the test conditions. While internal porosity in AM 316 L SS may serve as nucleation sites of creep voids and may be responsible for a relatively lower creep life, additively-manufactured 316 SS did not show inferior creep ductility when compared with conventionally-made 316 SS. The creep life of AM 316 L SS could be improved by stabilizing dislocation cell structure and/or reducing internal porosity through an optimized additive manufacturing process.

316 L stainless steel↗
DOE OSTI2021

Molecular dynamics simulations of radiation cascade evolution near cellular dislocation structures in additively manufactured stainless steels

The dislocation dense cellular structures observed in additively manufactured (AM) stainless steels can allow these materials to have enhanced strength and ductility compared to conventionally manufactured materials. Effective design of radiation resistant materials often necessitates creating microstructures containing of a high density of dislocations that act as sinks for radiation induced defects. This work uses molecular dynamics simulations to study the impact of pre-existing defects on radiation damage in stainless steel 316L fabricated by the laser powder bed fusion process. The evolution of synthetically generated dislocations in a crystal system in response to multiple radiation collision cascades suggest that dislocation dense regions reduce the probability of surviving point defects forming clusters. This finding seems to result from the dislocation cores’ ability to absorb point defects, thereby limiting the formation of clusters during the recombination phase. However, after successive cascades, the ability of the dislocation entanglement to prevent defect formation is diminished and defect cluster formation trends to an equilibrium. Accordingly, it is hypothesized that in an experimental setting the dislocation cells will initially act as neutral sinks for point defects, potentially delaying the onset of radiation damage effects; but, these structures will be degraded due to radiation-enhanced diffusion and lose their effectiveness at doses above 1.5–2 displacements per atom. Nevertheless, the ability to produce complex and feature-specific microstructures suggests promise for the design of radiation tolerant materials using AM methods.

36 MATERIALS SCIENCE↗
DOE OSTI2021

In situ high-energy X-ray study of deformation mechanisms in additively manufactured 316L stainless steel

A key structural material planned to be used in the core of the Transformational Challenge Reactor is the additively manufactured 316L stainless steel (AM 316L SS). While the deformation of conventionally-manufactured 316 SS have been extensively studied, the deformation mechanism of AM 316L SS is less known. Here the room-temperature tensile behavior of AM 316L SS was studied in situ using high-energy X-ray diffraction and X-ray tomography. Diffraction yielded the lattice strains and the dislocation densi-ties of the AM 316L SS, which were compared to those of a conventionally processed 316H SS. It was found that while the conventional 316H SS had three distinct deformation stages, namely stage II ather-mal hardening, stage III dynamic recovery, and stage IV, the AM 316L experienced only the stages III and IV after an initial transitional period. The plastic instability stresses (PIS), i.e. the true ultimate tensile strength, were nearly the same in both materials. The AM 316L had very low dislocation barrier strength throughout the plastic deformation, which, in combination with the invariant PIS, explained its high dis-location storage capability and the attractive combination of strength and ductility. Tomography revealed morphological changes of the built-in pores in the AM 316L during deformation and fracture, and it was concluded that large pores close to the surface might have significant roles in the necking stage.

316 stainless steel↗
DOE OSTI2021

Temperature and time effects of post-weld heat treatments on tensile properties and microstructure of Zircaloy-4

Opportunities exist to expand the application of Zircaloy-4 (Zry-4) into lower-temperature (<100°C) applications. Welded areas within these structures are potential failure points and post-weld heat treatments (PWHTs) are not yet standardized for application in this temperature range. Zry-4 tungsten inert gas (TIG) welds were given PWHTs from 450-900°C with hold times from 0.5-48 hours to investigate changes to tensile properties and microstructure. Treatment of 800°C for 1 hour was found to produce the most ductile material, measured by total elongation of the tensile bar (16.5%). Furthermore, both PWHT time and temperature were observed to increase total elongation, except in extreme (>800°C or >18hours) cases, but the effect of temperature was stronger. The second order cumulative annealing parameter shows a trend with tensile properties. Average grain sizes in the fusion zone and heat affected zone did not change under any of the PWHTs until the development of an undesirable blocky-alpha phase, which was only observed to form in the heat affected zones for hold times greater than 18hr at 800°C.

36 MATERIALS SCIENCE↗