Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Current stability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Investigation of instability, dynamic forces, and effect of dynamic loading on strength of cages for the bearings in the high pressure oxygen turbopumps for the space shuttle main engine

Experiments were performed to determine the effect of cyclic loading on bearing cage strength. A long term working tensile load of approximately 1300 N (300 lbs) was found to be the likely maximum. Higher loads caused a decrease in cage tensile strength after the 125,000 cycle testing period. Poisson's ratio in compression was found to be highly dependent upon the direction of the fiberglass plies. At room temperature the value was 0.15 with the plies and 0.68 across the plies. At -196 C (-321 F), the value with the plies was 0.20. The results of the analyses conducted have again demonstrated the critical need for improved lubrication in the high pressure oxygen turbopump bearings. Lubricant films with low shear strength and low friction coefficients promote cage stability and decrease ball/cage forces during marginal operating conditions. The analysis of the effect of combined bearing loads on ball/cage loads has identified a radial load of 3600 N (800 lbs) as the maximum for the current clearance of the balls and cage pockets. Liquid oxygen impinging on the cage in the direction of rotation was found to enhance cage stability.

Dufrane, K. F.↗
NASA NTRS2018

Gaps in Thermal Design Guidelines in the Goddard Space Flight Center GOLD Rules

The GSFC (Goddard Space Flight Center) GOLD Rules (Goddard Open Learning Design; GSFC-STD-1000) provide a reasonably comprehensive list of guidelines for the design and testing of spacecraft and instruments based on the long heritage of successful GSFC missions. In general, all GSFC missions are required to comply with the GOLD Rules across a number of subsystems or to seek waivers to particular GOLD rules where compliance is not practical, either due to the risk posture of a mission or the cost and/or schedule associated with compliance. In thermal subsystems, GOLD Rules are applied to design margins throughout the project life cycle and include temperature margins, heater power margins, and two-phase transport margins. However, no explicit guidance is provided for two thermal design aspects: heater control authority (for stability requirements) and cryogenic design margins (which are often not reasonable to express in terms of temperatures). This can lead to ambiguity and inconsistency among projects when demonstrating GOLD Rules compliance. Two current GSFC projects, TIRS-2 (Thermal InfraRed Sensor 2) and WFIRST (Wide Field InfraRed Survey Telescope), are both missions with cryogenic aspects and active thermal control for stability. This paper seeks to outline the characterization of cryogenic margins during the design process for TIRS-2 and WFIRST as well as the project derived guidelines for heater control authority margin. This effort serves as potential first steps for updating the GOLD Rules to address these two areas in guiding thermal designs at GSFC.

Modeling↗
NASA NTRSDate not supplied

Separation and Transition on a Cone-Cylinder-Flare: Computational Investigations

Base flow computation and stability analysis were conducted for hypersonic flow over a cone-cylinder-flare (CCF) geometry for conditions that correspond to the experimental runs carried out in three wind tunnels. Owing to the presence of an attached boundary layer, a separation bubble induced by a shock-boundary layer interaction, and a reattachment region, the chosen flow configuration is physically rich. The complexity of this flowfield encompasses a combination of convective instabilities developing on the cone, global instabilities in the separation bubble, and shear-layer modes and streaks in the reattachment region. Thus, the selected CCF configuration provides the opportunity for a comprehensive comparison of the currently available methodologies for analyzing boundary layer instabilities. Various tools are used for the analysis, including global stability codes as well as convective instability analyses based on a local theory, a weakly non-parallel analysis, and tools that are applicable to strongly non-parallel flows. The paper presents a comparison of the convective instability characteristics based on different methodologies, such as linear stability theory (LST), the harmonic form of linearized Navier-Stokes equations (HLNSE), and resolvent analysis. The CCF configuration provided an effective framework for conducting a detailed cross-validation of this type, which had not yet been addressed in existing literature. This document is accompanied by a companion paper that is focused on the experimental aspects of the CCF configuration. Both papers are being presented in a dedicated session that highlights the research activities of the NATO STO Research Task Group AVT-346.

Boundary Layer Transition↗
NASA NTRS1990

The effect of an electric field on the morphological stability of the crystal-melt interface of a binary alloy. III - Weakly nonlinear theory

The effect of a constant electric current on the crystal-melt interface morphology during directional solidification at constant velocity of a binary alloy is considered. A linear temperature field is assumed, and thermoelectric effects and Joule heating are neglected; electromigration and differing electrical conductivities of crystal and melt are taken into account. A two-dimensional weakly nonlinear analysis is carried out to third order in the interface amplitude, resulting in a cubic amplitude equation that describes whether the bifurcation from the planar state is supercritical or subcritical. For wavelengths corresponding to the most dangerous mode of linear theory, the demarcation between supercritical and subcritical behavior is calculated as a function of processing conditions and material parameters. The bifurcation behavior is a sensitive function of the magnitude and direction of the electric current and of the electrical conductivity ratio.

Wheeler, A. A.↗
NASA NTRS2014

Multi-Point Combustion System: Final Report

A low-NOx emission combustor concept has been developed for NASA's Environmentally Responsible Aircraft (ERA) program to meet N+2 emissions goals for a 70,000 lb thrust engine application. These goals include 75 percent reduction of LTO NOx from CAEP6 standards without increasing CO, UHC, or smoke from that of current state of the art. An additional key factor in this work is to improve lean combustion stability over that of previous work performed on similar technology in the early 2000s. The purpose of this paper is to present the final report for the NASA contract. This work included the design, analysis, and test of a multi-point combustion system. All design work was based on the results of Computational Fluid Dynamics modeling with the end results tested on a medium pressure combustion rig at the UC and a medium pressure combustion rig at GRC. The theories behind the designs, results of analysis, and experimental test data will be discussed in this report. The combustion system consists of five radially staged rows of injectors, where ten small scale injectors are used in place of a single traditional nozzle. Major accomplishments of the current work include the design of a Multipoint Lean Direct Injection (MLDI) array and associated air blast and pilot fuel injectors, which is expected to meet or exceed the goal of a 75 percent reduction in LTO NOx from CAEP6 standards. This design incorporates a reduced number of injectors over previous multipoint designs, simplified and lightweight components, and a very compact combustor section. Additional outcomes of the program are validation that the design of these combustion systems can be aided by the use of Computational Fluid Dynamics to predict and reduce emissions. Furthermore, the staging of fuel through the individually controlled radially staged injector rows successfully demonstrated improved low power operability as well as improvements in emissions over previous multipoint designs. Additional comparison between Jet- A fuel and a hydrotreated biofuel is made to determine viability of the technology for use with alternative fuels. Finally, the operability of the array and associated nozzles proved to be very stable without requiring additional active or passive control systems. A number of publications have been publish

Goeke, Jerry↗
NASA NTRS2005

DMBZ Polyimides Provide an Alternative to PMR-15 for High-Temperature Applications

PMR-15, a high-temperature polyimide developed in the mid-1970's at the NASA Lewis Research Center, offers the combination of ease of processing, low cost, and good stability and performance at temperatures up to 288 C (500 F). This material is widely regarded as one of the leading high-temperature matrix resins for polymer-matrix-composite aircraft engine components. PMR-15 is widely used in both military and civilian aircraft engines. The current worldwide market for PMR-15 is on the order of 50,000 lb, with a total sales of around $5 to $10 million. However, PMR-15 is made from methylene dianiline (MDA), a known animal mutagen and a suspected human mutagen. Recent concerns about the safety of workers involved in the manufacture and repair of PMR-15 components have led to the implementation of costly protective measures to limit worker exposure and ensure workplace safety. In some cases, because of safety and economic concerns, airlines have eliminated PMR-15 components from engines in their fleets. Current efforts at Lewis are focused on developing suitable replacements for PMR-15 that do not contain mutagenic constituents and have processability, stability, and mechanical properties comparable to that of PMR-15. A recent development from these efforts is a new class of thermosetting polyimides based on 2,2'-dimethylbenzidine (DMBZ). Autoclave processing developed for PMR-15 composites was used to prepare low-void-content T650-35 carbon-fiber-reinforced laminates from DMBZ-15 polyimides. The glass transition temperatures of these laminates were about 50 C higher than those of the T650- 35/PMR-15 composites (400 versus 348 C). In addition, DMBZ-15 polyimide composites aged for 1000 hr in air at 288 C (500 F) had weight losses close to those of comparable PMR-15 laminates (0.9 versus 0.7 percent). The elevated (288 C) and room temperature mechanical properties of T650-35-reinforced DMBZ-15 polyimide and PMR-15 laminates were comparable. Standard Ames tests are being conducted on this diamine to assess its mutagenicity.

Source record↗
NASA NTRS1966

Some Aspects of an Air-Core Single-Coil Magnetic Suspension System

This paper presents some of the technical aspects in the development at the Langley Research Center of an air-cove, dual-wound, single-coil, magnetic-suspension system with one-dimensional control. Overall electrical system design features and techniques are discussed in addition to the problems of control and stability. Special treatment is given to the operation of a dual-wound, high-current support coil which provides the bias fields and superimposed modulated field. Other designs features include a six-phase, solid-state power stage for modulation of the relatively large magnitude control current, and an associated six-phase trigger circuit.

SUPPORT SYSTEM↗
NASA NTRS1972

Temperature compensation of light emitting diodes and photodiodes.

Improved temperature compensation of the output from a GaAs LED can be obtained by connecting the diode in series with the emitter of an n-p-n transistor whose base circuit incorporates a high-gain operational amplifier and a parallel thermistor-resistor network. The temperature dependence of several photodiodes is also reported along with a practical temperature compensation scheme. Finally, the temperature compensation of a photon coupled pair consisting of a GaAs LED and a silicon photodiode is described. The combination provides a stability, linearity, and repeatability of about 1% over the upper 60% of the LED forward current range in the temperature interval from 15 to 45 C.

Burrous, C. N.↗
NASA NTRS1974

Integrated P-channel MOS gyrator

A gyrator circuit is described which is of the conventional configuration of two amplifiers in a circular loop, one producing zero phase shift and the other producing 180 phase reversal, in a circuit having medium Q composed of all field effect transistors of the same conductivity type. The current source to each gyrator amplifier comprises an amplifier which responds to changes in current, with the amplified signals feed back so as to limit current. The feedback amplifier has a large capacitor connected to bypass high frequency components, thereby stabilizing the output. The design makes possible fabrication of circuits with transistors of only one conductivity type, providing economies in manufacture and use.

Hochmair, E. S.↗
NASA NTRS1974

Inversion layer solar cell fabrication and evaluation

Inversion layer solar cells were fabricated by etching through the diffused layer on p-type silicon wafers in a comb-like contact pattern. The charge separation comes from an induced p-n junction at the surface. The inverted surface is caused by a layer of transparent material applied to the surface that either contains free positive ions or that creates donor states at the interface. Cells are increased from 3 ma I sub sc to 100 ma by application of sodium silicate. The action is unstable, however, and decays. Non-mesa contaminated oxide cells were fabricated with short circuit currents of over 100 ma measured in the sun. Cells of this type have demonstrated stability.

Call, R. L.↗
NASA NTRS1977

Proceedings of the 8th Precise Time and Time Interval (PTTI) Applications and Planning Meeting

The Proceedings contain the papers presented at the Eight Annual Precise Time and Tme Interval PTTI Applications and Planning Meeting. The edited record of the discussions following the papers and the panel discussions are also included. This meeting provided a forum for the exchange of information on precise time and frequency technology among members of the scientific community and persons with program applications. The 282 registered attendees came from various U.S. Government agencies, private industry, universities and a number of foreign countries were represented. In this meeting, papers were presented that emphasized: (1) definitions and international regulations of precise time sources and users, (2) the scientific foundations of Hydrogen Maser standards, the current developments in this field and the application experience, and (3) how to measure the stability performance properties of precise standards. As in the previous meetings, update and new papers were presented on system applications with past, present and future requirements identified.

Source record↗
NASA NTRS1980

Analytical and experimental evaluations of the effect of broad property fuels on combustors for commercial aircraft gas turbine engines

Analytical and experimental studies were conducted in three contract activities funded by the National Aeronautics and Space Administration, Lewis Research Center, to assess the impacts of broad property fuels on the design, performance, durability, emissions and operational characteristics of current and advanced combustors for commercial aircraft gas turbine engines. The effect of fuel thermal stability on engine and airframe fuel system was evaluated. Trade-offs between fuel properties, exhaust emissions and combustor life were also investigated. Results indicate major impacts of broad property fuels on allowable metal temperatures in fuel manifolds and injector support, combustor cyclic durability and somewhat lesser impacts on starting characteristics, lightoff, emissions and smoke.

Smith, A. L.↗
NASA NTRS1981

Wave-particle transport by weak electrostatic flow shear fluctuations

A description is presented of the first consistent theoretical treatment of transport due to weak electrostatic fluctuations from microinstabilities driven by a shear in plasma flow parallel to a uniform magnetic field. The model used considers electrostatic fluctuations in a Vlasov plasma with sheared bulk velocity parallel to a uniform magnetic field. The linear stability theory for the model has been studied by Gary and Schwartz (1980). In the current investigation, a calculation is performed of the wave-particle transport associated with the electrostatic flow shear instability.

Gary, S. P.↗
NASA NTRS1984

Preliminary results of experimental and analytical investigations of the tumbling phenomenon for an advanced configuration

A sustained autorotative pitching motion usually called 'tumbling' has been observed during dynamic model tests of the X-29A configuration. The X-29 is an advanced design incorporating forward-swept wings and canards in a highly relaxed static stability condition. Beginning with a historical review of the tumbling phenomenon, this paper discusses the current experimental results of dynamic model tumbling tests of the X-29 and the initial efforts to establish an aerodynamic and mathematical model for analysis.

Whipple, R. D.↗
NASA NTRS1987

Anomalous transport in discrete arcs and simulation of double layers in a model auroral circuit

The evolution and long-time stability of a double layer (DL) in a discrete auroral arc requires that the parallel current in the arc, which may be considered uniform at the source, be diverted within the arc to charge the flanks of the U-shaped double layer potential structure. A simple model is presented in which this current redistribution is effected by anomalous transport based on electrostatic lower hybrid waves driven by the flank structure itself. This process provides the limiting constraint on the double layer potential. The flank charging may be represented as that of a nonlinear transmission line. A simplified model circuit, in which the transmission line is represented by a nonlinear impedance in parallel with a variable resistor, is incorporated in a one-dimensional simulation model to give the current density at the DL boundaries. Results are presented for the scaling of the DL potential as a function of the width of the arc and the saturation efficiency of the lower hybrid instability mechanism.

Smith, Robert A.↗
NASA NTRS1988

Evaluation of Airborne Visible/Infrared Imaging Spectrometer Data of the Mountain Pass, California carbonatite complex

Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) data of the Mountain Pass, California carbonatite complex were examined to evaluate the AVIRIS instrument performance and to explore alternative methods of data calibration. Although signal-to-noise estimates derived from the data indicated that the A, B, and C spectrometers generally met the original instrument design objectives, the S/N performance of the D spectrometer was below expectations. Signal-to-noise values of 20 to 1 or lower were typical of the D spectrometer and several detectors in the D spectrometer array were shown to have poor electronic stability. The AVIRIS data also exhibited periodic noise, and were occasionally subject to abrupt dark current offsets. Despite these limitations, a number of mineral absorption bands, including CO3, Al-OH, and unusual rare earth element bands, were observed for mine areas near the main carbonatite body. To discern these bands, two different calibration procedures were applied to remove atmospheric and solar components from the remote sensing data. The two procedures, referred to as the single spectrum and the flat field calibration methods gave distinctly different results. In principle, the single spectrum method should be more accurate; however, additional fieldwork is needed to rigorously determine the degree of calibration success.

Crowley, James↗
NASA NTRS1987

Current CFD efforts in projectile aerodynamics

Information is given in viewgraph form on current computational fluid dynamics (CFD) efforts in projectile aerodynamics. Topics covered include spinning projectiles, fin stabilized projectiles, model geometry, the variation of base drag with base bleed, the variation of normal force with Mach number, and chordwise pressure distribution.

Nietubicz, Charles J.↗
NASA NTRS1992

Dynamics and control of coherent structure in turbulent jets

Current understanding of coherent structure dynamics in incompressible turbulent jets as explained by the nonlinear stability theory is reviewed, focusing on nonswirling turbulent jets. Topics addressed include hydrodynamic stability theory and coherent structures; dynamics of energy transfers among different scales of motion; nonlinear development of amplitude; development of single-frequency coherent mode; fundamental-subharmonic interaction and vortex pairing; and reversal of Reynolds stresses. Attention is also given to the effect of initial phase-difference angle between fundamental and subharmonic, conditions for resonance interaction, modulation of spreading rate by controlling coherent structure, turbulence enhancement or suppression due to excitation, 3D effects, jet noise, and swirling jets.

Mankbadi, Reda R.↗