Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Analytic gradients”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Chelation ion chromatography as an automated, and cost-effective analytical technique for REE determination: method development and applications

Rare earth elements (REEs), as critical minerals, have important uses in modern energy and technologies, yet are vulnerable to potential supply chain disruptions. To establish domestic REE supply chain, efficient REE detection methods for resource characterization and mineral processing will be needed to accelerate innovations for domestic REE recovery. This study developed a rapid, novel, and cost-effective for REE detection method using ion chromatography (IC) for aqueous samples. Various REE-targeted eluent gradients and post-column agent compositions were tested on the chelation ion chromatography (CIC) with UV-vis detector for optimal separation and quantification of REEs within approximately 20 min. The single-channel pump to deliver the post-column solution to UV-vis detector was replaced with a 4-channel gradient pump, to increase operation and maintenance efficiencies. After method optimization, resulting calibration curves for more than ten REEs achieved high coefficients of determination (R2>0.999) and low relatively standard deviations (below 3.24%), demonstrating sub-ppm level detection limits (0.0897 to 0.1149 mg/L). The reliability of the CIC method was validated through comparison with inductively coupled plasma mass spectrometry (ICP-MS), showing strong agreement in REE recovery from certified standards. The impact of metal ions and salts on REE recovery using CIC was also systematically investigated. CIC consistently exhibited reliable performance in the presence of salt solutions such as NaCl and Na₂SO₄ (up to 10,000 mg/L). Our study also found the presence of high concentrations of Al ions (at 10,000 mg/L) significantly influenced REE determination, and elevated concentrations of Ca ions affected the recovery of specific REEs, including La, Ce, and Pr. The CIC method was further tested on REE-containing eluents from solvent extraction tests out of fly ash leachates. REE detection from these real processing fluids were reported to achieve 90% to 100% recovery rate from our IC method, compared to ICP-MS results. This study underscores the potential of CIC as a reliable and efficient alternative for REE determination in complex matrices. It also highlights the importance of minimizing select interfering metal ions in solutions to ensure accurate results. The REE CIC method presents a promising, low-maintenance, salt-tolerant, and cost-effective alternative to traditional analytical methods for REE analysis.

detection of rare earth elements (REE)↗
NASA NTRS1977

Effects of finite plasma beta on the lower-hybrid-drift instability

The local dispersion relation for the lower-hybrid-drift (LHD) instability is derived and analyzed, taking into account the finite-beta effects associated with transverse electromagnetic perturbations as well as with resonant and nonresonant electron-orbit modifications due to magnetic-field gradients. The influence of finite-beta effects on the LHD instability is calculated in a fully self-consistent manner for arbitrary values of electron-ion temperature ratio, local beta, cross-field ExB velocity/ion thermal speed ratio, and other plasma parameters. Stability properties are investigated analytically for the case of cold electrons, and the local dispersion relation is solved numerically in the parameter regime of most interest for high-density plasma pinches. The results show that for all parameter regimes studied, the net effect of finite plasma beta is to reduce the maximum growth rate of the LHD instability, although the details can vary, depending on the plasma parameters. Except in the limit where the electron/ion temperature ratio tends to zero, it is found that there is a critical value of plasma beta above which the LHD instability is completely stabilized.

Davidson, R. C.↗
NASA NTRS2008

Further Developments in Modeling Creep Effects Within Structural SiC/SiC Components

Anticipating the implementation of advanced SiC/SiC composites into turbine section components of future aero-propulsion engines, the primary objective of this on-going study is to develop physics-based analytical and finite-element modeling tools to predict the effects of constituent creep on SiC/SiC component service life. A second objective is to understand how to possibly manipulate constituent materials and processes in order to minimize these effects. Focusing on SiC/SiC components experiencing through-thickness stress gradients (e.g., airfoil leading edge), prior NASA creep modeling studies showed that detrimental residual stress effects can develop globally within the component walls which can increase the risk of matrix cracking. These studies assumed that the SiC/SiC composites behaved as isotropic viscoelastic continuum materials with creep behavior that was linear and symmetric with stress and that the creep parameters could be obtained from creep data as experimentally measured in-plane in the fiber direction of advanced thin-walled 2D SiC/SiC panels. The present study expands on those prior efforts by including constituent behavior with non-linear stress dependencies in order to predict such key creep-related SiC/SiC properties as time-dependent matrix stress, constituent creep and content effects on composite creep rates and rupture times, and stresses on fiber and matrix during and after creep.

Lang, Jerry↗
DOE OSTI2023

Quantitative Separation of Unknown Organic–Metal Complexes by Liquid Chromatography–Inductively Coupled Plasma-Mass Spectrometry

Dissolved organic matter (DOM) is widely recognized to control the solubility and reactivity of trace metals in the environment. However, the mechanisms that govern metal-DOM complexation remain elusive, primarily due to the analytical challenge of fractionating and quantifying metal–organic species within the complex mixture of organic compounds that comprise DOM. Here, we describe a quantitative method for fractionation and element-specific detection of organic–metal complexes using liquid chromatography with online inductively coupled plasma mass spectrometry (LC–ICP-MS). The method implements a post-column compensation gradient to stabilize ICP–MS elemental response across the LC solvent gradient, thereby overcoming a major barrier to achieving quantitative accuracy with LC–ICP-MS. With external calibration and internal standard correction, the method yields concentrations of organic–metal complexes that were consistently within 6% of their true values, regardless of the complex’s elution time. We used the method to evaluate the effects of four stationary phases (C18, phenyl, amide, and pentafluoroylphenyl propyl) on the recovery and separation of environmentally relevant trace metals (Mn, Fe, Co, Ni, Cu, Zn, Cd, and Pb) in Suwannee River Fulvic Acid and Suwannee River Natural Organic Matter. The C18, amide, and phenyl phases generally yielded optimal metal recoveries (>75% for all metals except Pb), with the phenyl phase separating polar species to a greater extent than C18 or amide. We also fractionated organic-bound Fe, Cu, and Ni in oxidized and reduced soils, revealing divergent metal-DOM speciation across soil redox environments. Finally, by enabling quantitative fractionation of DOM-bound metals, our method offers a means for advancing a mechanistic understanding of metal–organic complexation throughout the environment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Learning how structures form in drift-wave turbulence

Drift-wave turbulence produces anomalous transport via cross-correlations between fluctuations. This transport has profound implications for confinement, structure formation, and virtually all aspects of the non-linear turbulent dynamics. Herein, we use a data-driven method based on deep learning in order to study turbulent transport in the 2D Hasegawa–Wakatani system and infer a reduced mean-field model from numerical solution. In addition to the usual turbulent diffusion, we find an effect which couples the particle flux to the local gradient of vorticity, which tends to modulate the density profile. The direct coupling to the shear is relatively weak. In addition, the deep learning method finds a model for spontaneous zonal flow generation by negative viscosity, stabilized by non-linear and hyperviscous terms. We compare these results to analytic calculations using quasilinear theory and wave kinetics, finding qualitative agreement, though the calculations miss certain higher-order effects. A simplified, 1-D model for the evolution of the profile, flow, and intensity based on the deep learning results is solved numerically and compared to previous models for staircasing based on bistability. We see that the physics uncovered by the deep learning method provided simple explanations for the formation of zonal structures in the density, flow, and turbulence fields. We highlight the important role of symmetry in the deep learning method and speculate on the portability of the method to other applications.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRSDate not supplied

Blade and Takeoff Trajectory Optimization of a Propeller-Driven Electric Aircraft with Acoustic Constraints

In this work, a multi-disciplinary toolchain is described and used to optimize the takeoff trajectory of a electrified general aviation aircraft, subjected to acoustic constraints. The Dymos multi-disciplinary optimal control library is used to optimize the trajectory, with propeller aerodynamic and acoustic models provided by blade element momentum theory (CCBlade.jl) and acoustic analogy (AcousticAnalogies.jl) codes, respectively. Each model is implemented in the OpenMDAO framework, with all derivatives calculated either analytically or via automatic differentiation tools. The toolchain is applied to a hypothetical electrified form of the Cirrus SR20 and compared to the conventional piston-driven form.

gradient-based optimization↗
DOE OSTI2020

Crossing symmetry, transcendentality and the Regge behaviour of 1d CFTs

We develop the technology for Polyakov-Mellin (PM) bootstrap in one- dimensional conformal field theories (CFT 1 ). By adding appropriate contact terms, we bootstrap various effective field theories in AdS 2 and analytically compute the CFT data to one loop. The computation can be extended to higher orders in perturbation theory, if we ignore mixing, for any external dimension. We develop PM bootstrap for O(N) theories and derive the necessary contact terms for such theories (which also involves a new higher gradient contact term absent for N = 1). We perform cross-checks which include considering the diagonal limit of the 2d Ising model in terms of the 1d PM blocks. As an independent check of the validity of the results obtained with PM bootstrap, we propose a suitable basis of transcendental functions, which allows to fix the four-point correlators of identical scalar primaries completely, up to a finite number of ambiguities related to the number of contact terms in the PM basis. We perform this analysis both at tree level (with and without exchanges) and at one loop. We also derive expressions for the corresponding CFT data in terms of harmonic sums. Finally, we consider the Regge limit of one-dimensional correlators and derive a precise connection between the latter and the large-twist limit of CFT data. Exploiting this result, we study the crossing equation in the three OPE limits and derive some universal constraints for the large-twist limit of CFT data in Regge-bounded theories with a finite number of exchanges.

1/N expansion↗
DOE OSTI2020

Slip band characteristics in the presence of grain boundaries in nickel-based superalloy

Shear strain profiles along slip bands in a modified Rolls-Royce nickel superalloy (RR1000) were analyzed for a tensile sample deformed by 2%. The strain increased with distance away from a grain boundary (GB), with maximum shear strain towards the center of the grain, indicating that dislocation nucleation generally occurred in the grain interior. The strain gradients in the neighborhood of the GBs were quantified and generally correlated with rotation about the active slip system line direction. This leads to an ability to determine the active slip system in these regions. The dislocation spacing and pileup stresses were inferred. The dislocation spacing closely follows an Eshelby analytical solution for a single ended pileup of dislocations under an applied stress. The distribution of pileup stress values for GBs of a given misorientation angle follows a log-normal distribution, with no correlation between the pileup stress and the GB misorientation angle. Furthermore, there is no observed correlation between various transmissivity factors and slip band pileup stress. Hence it appears that the obstacle strength of any of the observed GBs is adequate to facilitate the dislocation pileups present in the slip bands. However, slip band transmission does correlate with transmissivity factors, with the current study focusing on the Luster and Morris m’-factor. Observation of strain profiles of transmitted bands indicate dislocation nucleation locations.

36 MATERIALS SCIENCE↗
DOE OSTI2024

SNNVis: Visualizing Graph Embedding of Evolutionary Optimization for Spiking Neural Networks

While Spiking Neural Networks (SNNs) show a lot of promise, it is difficult to optimize them because applying traditional gradient-based optimization techniques is difficult. Even though evolutionary algorithms (EAs) have been shown to promise to optimize SNNs, understanding the relationship between evolving the characteristics of SNNs and their performance to improve the optimization algorithm is challenging because of the complex characteristics and huge population size. We propose visual analytics with novel graph embedding for evolutionary SNNs to address the challenges. While existing graph embedding techniques have limitations in preserving the specific features of the nodes and edges, our approach maintains them. Also, we develop visual analytics for understanding the relationship between the network performance and the features of nodes and edges and exploring and analyzing the evolving SNNs to build insights into improving the EA.

Chae, Junghoon [ORNL] (ORCID:0000000206016746)↗
NASA NTRS1995

Numerical simulation of the nonlinear response of composite plates under combined thermal and acoustic loading

A time-domain study of the random response of a laminated plate subjected to combined acoustic and thermal loads is carried out. The features of this problem also include given uniform static inplane forces. The formulation takes into consideration a possible initial imperfection in the flatness of the plate. High decibel sound pressure levels along with high thermal gradients across thickness drive the plate response into nonlinear regimes. This calls for the analysis to use von Karman large deflection strain-displacement relationships. A finite element model that combines the von Karman strains with the first-order shear deformation plate theory is developed. The development of the analytical model can accommodate an anisotropic composite laminate built up of uniformly thick layers of orthotropic, linearly elastic laminae. The global system of finite element equations is then reduced to a modal system of equations. Numerical simulation using a single-step algorithm in the time-domain is then carried out to solve for the modal coordinates. Nonlinear algebraic equations within each time-step are solved by the Newton-Raphson method. The random gaussian filtered white noise load is generated using Monte Carlo simulation. The acoustic pressure distribution over the plate is capable of accounting for a grazing incidence wavefront. Numerical results are presented to study a variety of cases.

Mei, Chuh↗
NASA NTRS2003

Numerical Modeling, Thermomechanical Testing, and NDE Procedures for Prediction of Microcracking Induced Permeability of Cryogenic Composites

Reusable Space Vehicles will include light cryogenic composite fuel tanks that must not leak excessively even after multiple launches. Damage in cryogenic composite fuel tanks induced during manufacturing and advanced by thermomechanical cycling can accelerate leakage of the propellant. Whether the leakage exceeds tolerable levels depends on many factors, including pressure gradients, microcrack density, other damage such as delamination, connectivity of the cracks, residual stresses from manufacture, service-induced stresses from thermal and mechanical loads, and composite lay-up. Although it is critical to experimentally characterize permeability during various thermal and mechanical load histories, optimal design depends on having analytical models that can predict the effect of various parameters on performance. Our broad goal is to develop such models that are experimentally validated by destructive and non-destructive evaluation means.

Noh, Jae↗
NASA NTRS1991

Design of cryogenic tanks for space vehicles shell structures analytical modeling

The initial objective was to study the use of superplastically formed corrugated hat section stringers and frames in place of integrally machined stringers over separate frames for the tanks of large launch vehicles subjected to high buckling loads. The ALS was used as an example. The objective of the follow-on project was to study methods of designing shell structures subjected to severe combinations of structural loads and thermal gradients, with emphasis on new combinations of structural arrangements and materials. Typical applications would be to fuselage sections of high speed civil transports and to cryogenic tanks on the National Aerospace Plane.

Copper, Charles↗
DOE OSTI2022

Near-cancellation of up- and down-gradient momentum transport in forced magnetized shear-flow turbulence

Visco-resistive magnetohydrodynamic turbulence, driven by a two-dimensional unstable shear layer that is maintained by an imposed body force, is examined by decomposing it into dissipationless linear eigenmodes of the initial profiles. The down-gradient momentum flux, as expected, originates from the large-scale instability. However, continual up-gradient momentum transport by large-scale linearly stable but nonlinearly excited eigenmodes is identified and found to nearly cancel the down-gradient transport by unstable modes. The stable modes effectuate this by depleting the large-scale turbulent fluctuations via energy transfer to the mean flow. This establishes a physical mechanism underlying the long-known observation that coherent vortices formed from nonlinear saturation of the instability reduce turbulent transport and fluctuations, as such vortices are composed of both the stable and unstable modes, which are nearly equal in their amplitudes. The impact of magnetic fields on the nonlinearly excited stable modes is then quantified. Furthermore, even when imposing a strong magnetic field that almost completely suppresses the instability, the up-gradient transport by the stable modes is at least two-thirds of the down-gradient transport by the unstable modes, whereas for weaker fields, this fraction reaches up to 98%. These effects are persistent with variations in magnetic Prandtl number and forcing strength. Finally, continuum modes are shown to be energetically less important, but essential for capturing the magnetic fluctuations and Maxwell stress. A simple analytical scaling law is derived for their saturated turbulent amplitudes. It predicts the falloff rate as the inverse of the Fourier wavenumber, a property which is confirmed in numerical simulations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

FutureTense

Protective vaccines and reliable diagnostics are essential tools for controlling viral diseases. However, the efficacy of these tools can be diminished by mutations in viral genomes. The delay between the emergence of new viral strains and the redesign of vaccines and diagnostics allows for continued viral transmission. Is it possible to address this challenge by computationally predicting viral genome sequence evolution? Can we “future-proof” vaccines and diagnostics by targeting both current and anticipated future sequence variants? While predicting viral evolution is still an unsolved, “grand challenge” problem in biology, the large, and rapidly growing, number of SARS-CoV-2 genome sequences provide an opportunity to quantify the ability of machine learning to predict viral genome sequence evolution. Towards this end, we have developed a simple computational model for predicting viral evolution at the level of individual nucleotides. The key metric for quantifying the per-base, prediction accuracy for viral evolution is the Mann-Whitney U statistic (or, equivalently, the area under the receiver operator curve). Since the Mann-Whitney U statistic is not a differentiable function, existing deep leaning packages (like Pytorch and Keras/TensorFlow) are not useful, as they require that the accuracy metric/objective function be analytically differentiable with respect to the model parameters. To overcome this challenge, we have implemented custom software, “FutureTense”, that can train a machine learning model by maximizing the non-differentiable Mann-Whitney U statistic. This software trains a machine learning model by exploring along the direction of the discrete gradient of the Mann-Whitney U statistic in the model parameter space. Parallel computing and genome sequence-specific optimizations are used to accelerate model training. The resulting machine learning model learns the observed high C->U mutation rates in the SARS-CoV-2 genome (which are potentially induced by host defenses) and provides prediction accuracies that are significantly better than one would expect from random chance. While predicting viral evolution is still quite far from a solved problem, the surprising performance of this simple model gives hope that the accuracy of predicting viral genome evolution can be further increased by more sophisticated approaches.

Gans, Jason↗
NASA NTRS1979

Gap heating with pressure gradients

The heating rate distribution and temperature response on the gap walls of insulating tiles is analyzed to determine significant phenomena and parameters in flows where there is an external surface pressure gradient. Convective heating due to gap flow, modeled as fully developed pipe flow, is coupled with a two-dimensional thermal model of the tiles that includes conduction and radiative heat transfer. To account for geometry and important environmental parameters, scale factors are obtained by curve-fitting measured temperatures to analytical solutions. These scale factors are then used to predict the time-dependent gap heat flux and temperature response of tile gaps on the Space Shuttle Orbiter during entry.

Scott, C. D.↗
NASA NTRS1987

Dynamic topography and gravity anomalies for fluid layers whose viscosity varies exponentially with depth

Adopting the formalism of Parsons and Daly (1983), analytical integral equations (Green's function integrals) are derived which relate gravity anomalies and dynamic boundary topography with temperature as a function of wavenumber for a fluid layer whose viscosity varies exponentially with depth. In the earth, such a viscosity profile may be found in the asthenosphere, where the large thermal gradient leads to exponential decrease of viscosity with depth, the effects of a pressure increase being small in comparison. It is shown that, when viscosity varies rapidly, topography kernels for both the surface and bottom boundaries (and hence the gravity kernel) are strongly affected at all wavelengths.

Revenaugh, Justin↗
NASA NTRS1990

Comparison of solution approaches for minimum-fuel, low-thrust, power-limited orbital transfers

An initial assessment of the feasibility of a function space gradient method for computing solutions to minimum-fuel power-limited transfers encompassing a wide range of thrust to weight ratios is conducted. Three transfers between coplanar ellipses are used as test cases. The gradient method performs best at the high end of the thrust to weight ratio range. At the lower end, there is reduced sensitivity of the fuel consumption to the control profiles. The minimum fuel consumption and the trajectory are computed quite accurately but the control profiles are in error. An approximate analytical solution, obtained by Edelbaum using the method of averaging, is discussed.

Mease, Kenneth D.↗