Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Al2O3”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

The effects of particulates from solid rocket motors fired in space

The orbits attained by kick motor solid propellant particulates are modeled, and an estimate is made of the number of particulates which will remain in orbit. The fuel, Al2O3, is burned while inserting spacecraft into a transfer orbit and again while circularizing the GEO station. It is shown that 23 percent of 1 micron particles deorbit immediately, while most particles enter a retrograde orbit. The resulting flux is an order of magnitude larger than the micrometeoroid flux. The pressures exerted by solar radiation ensure that only 5 percent of the original flux is still in orbit after the first year. The estimates provided are valid for a large number of transfer orbit operations, but will vary widely over the short term.

Mueller, A. C.↗
NASA NTRS1985

Shock induced radiation from minerals

Schmitt and Ahrens (1983) have concluded that the type of optical emission produced during shock compression was dependent upon phase changes taking place during shock compression. The present study is concerned with new observations of shock-induced optical radiation from Al2O3, MgO, NaCl, KCl, x-cut and fused SiO2, and LiF at various pressures up to 75 GPa. The experimental setup used in the study is similar to that employed by Schmitt and Ahrens. An Image Converter Camera with a three-frame plug-in unit was added to take two or three exposures of the radiation field during shock wave propagation through the sample, taking into account exposure times in the range from 50 to 500 nsec. The greybody emissions observed in LiF, which undergoes no phase transition, imply that localized heating and perhaps melting occurs in this material during shock deformation.

Schmitt, D.↗
NASA NTRS1986

Etching Silicon Films With Xenon Difluoride

Microscopic circuit structures prepared for probing. Xenon difluoride removes relatively large amounts of silicon from integratedcircuit or solar-cell structures while leaving SiO2, Si3N4, Al2O3, and other compounds intact. In Etching Apparatus, solid XeF2 sublimated in vacuum, then allowed to flow over sample at controlled rate and pressure. Wafer etched from back to expose SiO2 and Al layers for spectroscopic analysis of SiO2/Al interface. Using XeF2 technique, silicon wafer with oxide layer reduced in thickness from standard 300 micrometer to as little as 10 nanometer without adversely affecting oxide.

Hecht, M. H.↗
NASA NTRS1985

Gel Precursors as Glass and Ceramic Starting Materials for Space Processing Applications Research

The crystallization kinetics and glass forming ability of reluctant glass formers is investigated. This could ultimately aid the formation of bulk samples of unique glass compositions outside of normal glass forming regions allowing the optimization of certain properties of the glass. One important aspect of processing in space is the containerless undercooling of molten substances. Theoretically, the extent of undercooling can be greatly enhanced by solidifying in the absence of heterogeneous nucleation resulting from contact with crucibles or molds. Techniques were established for the measurement of crystallization kinetics and critical cooling rates. The glass formation ability and crystallization kinetics of Ga2O-43CaO and several Al2O3-CaO compositions were measured. An apparatus was set up to measure the temperature of spherical samples on a thermocouple at large cooling rates. The time and temperature of nucleation is recorded and the probability of nucleation at various cooling rates can be measured.

Downs, R. L.↗
NASA NTRS1985

Glass Formation in Reluctant Glass Formers

The crystallization kinetics and glass forming ability of reluctant glass formers is investigated. This could ultimately aid the formation of bulk samples of unique glass compositions outside of normal glass forming regions allowing the optimization of certain properties of the glass. One important aspect of processing space is the containerless undercooling of molten substances. Theoretically, the extent of undercooling can be greatly enhanced by solidifying in the absence of heterogeneous nucleation resulting from contact with crucibles or molds. Techniques were established for the measurement of crystallization kinetics and critical cooling rates. The glass formation ability and crystallization kinetics of Ga2O-43CaO and several Al2O3-CaO compositions were measured. An apparatus was set up to measure the temperature of spherical samples on a thermocouple at large cooling rates. The time and temperature of nucleation is recorded and the probability of nucleation at various cooling rates can be measured.

Ethridge, E. C.↗
NASA NTRS1985

Use of Hydration Inhibitors to Improve Bond Durability of Aluminum Adhesive Joints

An investigation is conducted of the mechanisms by which nitrilotris methylene phosphonic acid (NTMP) and related compounds are adsorbed onto oxidized aluminum surfaces to inhibit hydration and increase the durability of adhesive bonds formed with inhibitor-treated panels. P - O - Al bonds are identified as the basis of adsorption, and it is found that water initially adsorbed onto the etched aluminum surfaces is displaced by the NTMP. The hydration of the NTMP-treated surfaces occurs in three stages, namely the reverisble physisorption of water, the slow dissolution of NTMP followed by rapid hydration of the freshly exposed Al2O3 to AlOOH and further hydration of the surface to Al(OH)3. Five properties of an ideal inhibitor are identified.

Davis, G. D.↗
NASA NTRS1985

Estimation of particle size based on LDV measurements in a de-accelerating flow field

The accuracy of velocity measurements made with a laser velocimeter is strongly dependent upon the response of the seeding particles to the dynamics of the flow field. The smaller the particle the better the response to flow fluctuations and gradients and therefore the more accurate velocity measurement. In direct conflict is the requirement of light scattering efficiency to obtain signals with the laser velocimeter which, in general, is better as the particle size is increased. In low speed flow fields these two requirements on particle size overlap and accurate measurements may be obtained. However in high speed flows, where the velocity gradients may be severe, very small particles are required to maintain sufficient dynamic response characteristics to follow the flow. Therefore if velocity measurements are to be made in these flows, the laser velocimeter must be designed with sufficient sensitivity to obtain signals from these small particles. An insitu determination of the size distribution of kaolin particles (Al2O3, .2 + or - SiO2 . 2H2O) in the 16-foot Transonic Tunnel and the sensitivity characteristics of the laser velocimeter system is described.

Meyers, J. F.↗
NASA NTRS1986

Manufacture of high-density ceramic sinters

High density ceramic sinters are manufactured by coating premolded or presintered porous ceramics with a sealing material of high SiO2 porous glass or nitride glass and then sintering by hot isostatic pressing. The ceramics have excellent abrasion and corrosion resistances. Thus LC-10 (Si3N2 powder) and Y2O3-Al2O3 type sintering were mixed and molded to give a premolded porous ceramic (porosity 37%, relative bulk density 63%). The ceramic was dipped in a slurry containing high SiO2 porous glass and an alcohol solution of cellulose acetate and dried. The coated ceramic was treated in a nitrogen atmosphere and then sintered by hot isostatic pressing to give a dense ceramic sinter.

Hibata, Y.↗
NASA NTRS1985

Ultramafic parent magmas for mare basalts?

Solidification products of basaltic magmas (fine grained basalts and ultramafic glasses) at the Apollo 15 site were examined. Consideration of simple MgO-6IO2-Al2O3 systematics plus results of calculations of fractional crystallization was reviewed. Suggestions are presented to account for the lack of correlation between the ultramafic glasses and basalts.

Longhi, J.↗
NASA NTRS1986

Oxidation and emittance of superalloys in heat shield applications

Recently developed superalloys that form alumina coatings have a high potential for heat shield applications for advanced aerospace vehicles at temperatures above 1095C. Both INCOLOY alloy MA 956 (of the Inco Alloys International, Inc.), an iron-base oxide-dispersion-strengthened alloy, and CABOT alloy No. 214 (of the Cabot Corporation), an alumina-forming nickel-chromium alloy, have good oxidation resistance and good elevated temperature strength. The oxidation resistance of both alloys has been attributed to the formation of a thin alumina layer (alpha-Al2O3) at the surface. Emittance and oxidation data were obtained for simulated Space Shuttle reentry conditions using a hypersonic arc-heated wind tunnel. The surface oxides and substrate alloys were characterized using X-ray diffraction and scanning and transmission electron microscopy with an energy-dispersive X-ray analysis unit. The mass loss and emittance characteristics of the two alloys are discussed.

Wiedemann, K. E.↗
NASA NTRS1986

Relation between microstructural heterogeneous surface layer and nitrogen pressure during sintering in Si3N4-Ml2O3 ceramics

The effects of N2 pressure (0.1 to 50 MPa) during sintering on the thickness of the microstructurally heterogeneous layer (MHL) formed near the surface of the compact, transverse-rupture strength, were investigated for Si3N4-(10 to 20) mol % MgO-5.5 mol % Al2O3 ceramics. The sintering temperature and time were 1973 K and 3.6 ks, respectively. The N2 gas was introduced into the furnace at about 1273 K. When the compacts were sintered under a certain N2 pressure, for example, about 20 and 7 MPa for 10 and 15 mol% MgO, respectively, the evolutions of N and Si were suppressed. The thickness of the MHL became very small and at the same time the strength of the surface layer of the compact (which was normally less than that of the inside in the case of 0.1 MPa) became nearly the same value as that of the inside. At higher pressure, the strength of both surface layer and the inside decreased considerably. Some discussion was made on these results.

Hayashi, K.↗
NASA NTRS1985

Analysis of TQCM surface contamination adsorbed during the Spacelab I Mission

The Temperature-Controlled Quartz Crystal Microbalance (TQCM) system was flown on the Spacelab I Mission as part of the Induced Environment Contamination Monitor to monitor surface contamination (SC) in the payload bay. SC on the five sensors of the TQCM was analyzed by means of IR spectroscopy, scanning electron spectroscopy, and energy dispersive X-ray fluorescence. The amount of SC ranged from 1.4 micrograms/sq cm for the -Z sensor to 39.9 micrograms/sq cm for the +X sensor. The IR analysis showed strong CH2, CH3, and carbonyl absorption bands, indicative of ester and polyester compounds found in adhesives, plasticizers, and tape. The particulates (mostly ranging from 1 micron to 20 microns in size) were mainly composed of Mg, Al, Al2O3, and Si, and probably originated in the solid rocket firings.

Mckeown, D.↗
NASA NTRS1985

Ion beam sputter-deposited thin film coatings for protection of spacecraft polymers in low earth orbit

Ion beam sputter-deposited thin films at Al2O3, SiO2, and a codeposited mixture of predominantly SiO2 with small amounts of fluoropolymer were evaluated both in laboratory plasma ashing tests and in space on board Shuttle flight STS-8 for effectiveness in preventing oxidation of polyimide Kapton. Measurements of mass loss and optical performance of coated and uncoated polyimide samples exposed to the low earth orbital environment are presented. Optical techniques were used to measure loss rates of protective films exposed to atomic oxygen. Results of the analysis of the space flight exposed samples indicate that thin film metal oxide coatings are very effective in protecting the polyimide. Metal oxide coatings with a small amount of fluoropolymer codeposited have the additional benefit of great flexibility.

Banks, B. A.↗
NASA NTRS1985

Pretreatment effects on the morphology and properties of aluminum oxide thermally grown on NiCoCrAlY

The effect of pretreatments on the morphology and properties of aluminum oxide thermally grown from NiCoCrAlY was investigated. The goal was to optimize process steps to produce a highly adherent, continuous, and insulating aluminum oxide. Two pretreatments were carried out, one in vacuum (about 0.0001 Torr) at 1350 K for 5 h, and the other consisting of deposition of a 1-micron thick Al2O3 film by activated reactive evaporation. Samples were subsequently oxidized thermally at 1000 C for 50 h at 0.5 Torr oxygen pressure. The two pretreatments were carried out on electron-beam evaporation NiCoCrAlY, about 120 microns thick, deposited on a superalloy turbine blade substrate. The results showed that the thermally grown oxide was significantly different in microstructure, surface topography and in its adherence to the NiCoCrAlY for the two pretreatments. Optimum results were obtained by combining the two pretreatments to produce an adherent, continuous, and insulating oxide film on the NiCoCrAlY-coated superalloy substrate.

Prakash, S.↗
NASA NTRS1985

Effect of R(3+) ions on the structure and properties of lanthanum borate glasses

The present investigation of glass formation in the (mole percent) systems 25La2O3 (x)R2O3 (75-x)B2O3, where R = Al, Ga, and (25-x)La2O3 (x)Ln2O3 75B2O3, where Ln = Gd, Er, Y, notes that up to 25 mol pct Al2O3 or Ga2O3 can be substituted for B2O3, while no more than about 5 mol pct Ln2O3, substituted for La2O3, caused macro-phase separation. The substitution of either R2O3 or Ln2O3 in the lanthanum borate system changes the separation distance between adjacent B3O6 chains. The effect of this structural change on the molar volume, transformation temperature, thermal expansion coefficient, and transformation-range viscosity is discussed.

Chakraborty, I. N.↗
NASA NTRS1985

Selected fretting-wear-resistant coatings for Ti-6 pct Al-4 pct V alloy

The ability of several wear-resistant coatings to reduce fretting in the Ti-6Al-4V alloy is investigated. The experimental apparatus and procedures for evaluating fretting in uncoated Ti-6Al-4V alloy and in the alloy with plasma-sprayed coatings, polymer-bonded coating, and surface treatments are described. The wear volume and wear rate for the alloys are measured and compared. It is concluded that Al2O3 with 13 percent TiO2, preoxidation and nitride surface treatments, and MoS2 sputtering result in wear-resistant surfaces; however, the polyimide coating is the most wear resistant coating in both dry and moist air, and it causes the least wear to the uncoated alloy surface.

Bill, R. C.↗
NASA NTRS1986

Evidence for successive episodes of condensation at high temperature in a part of the solar nebula

A polished thin section of a Ca-Al-rich inclusion CAI 3643 from the Allende meteorite has been studied by means of light and scanning electron microscopes, and electron and proton microprobes. The appearance and the mineral composition of the inclusion's three concentric layers: core, mantle, and crust are described. Despite differences in texture and composition, the three layers display a continuity in their modal mineralogical compositions, their extreme Al2O3 enrichments (53-69 percent, compared to 25-45 percent in other CAIs), and their trace element complementarity. This implies that all the layers of CAI 3643 have formed from the same cooling gaseous reservoir within a limited interval of time and space, consistent with an origin in a local transient heating event in the CV chondrite formation region of the nebula.

Wark, D. A.↗
NASA NTRS1985

Preparation and analysis of particulate metal deposits

Small particles and clusters of palladium were grown by deposition from the vapor phase under ultrahigh vacuum conditions. Amorphous and crystalline support films of Al2O3 and ultrathin amorphous carbon films were used as substrate materials. The growth of the metal deposit was monitored in situ by scanning transmission diffraction of energy-filtered 100 kV electrons and high resolution transmission electron microscopy (TEM) analysis was performed in a separate instrument. It was established by in situ TEM, however, that the transfer of specimens in this case did not unduly affect the size and distribution of deposit particles. It was found that the cleanness, stoichiometry, crystallinity and structural perfection of the support surface play an essential role in determining the crystalline perfection and structure of the particles. The smallest palladium clusters reproducibly prepared contained not more than six atoms but size determinations below 1 nm average particle diameter are very problematic with conventional TEM. Palladium particles grown on carbon supports feature an impurity-stabilized mosaic structure.

Poppa, H.↗