Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Aircraft structures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

The 1-((diorganooxyphosphonyl)-methyl)-2,4- and -2,6-diamido benzenes

1-((Diorgano oxyphosphonyl) methyl)-2,4- and -2,6-dinitro and diamino benzenes are prepared by nitrating an (organophosphonyl) methyl benzene to produce the dinitro compounds which are then reduced to the diamino compounds. The organo grounds (alkyl, haloalkyl, aryl) on the phosphorus may be removed to give the free acids (HO)2P(double bond O)single bond. The diamino compounds may be polymerized with dianhydrides or diacyl halides to produce fire and flame resistant polymers which are useful in the manufacture of aircraft structures.

Mikroyannidis, John A.↗
NASA NTRS1989

Some 1-(diorganooxyphosphonyl)methyl-2,4- and -2,6-dinitro-benzenes

1-(Diorgano oxyphosphonyl) methyl) 2,4- and 2,6-dinitro- and diamino benzenes are prepared by nitrating an (organophosphonyl)methly benzene to produce the dinitro compounds which are then reduced to the diamino compounds. The organo group (alkyl, haloalkyl, aryl) on the phosphorus may be removed to give the free acids, (HO)2P(double bond O) single bond. The diamino compounds may be polymerized with dianhydrides or diacyl halides to produce fire and flame resistant polymers which are useful in the manufacture of aircraft structures.

Mikroyannidis, John A.↗
NASA NTRS1990

A Protection And Detection Surface (PADS) for damage tolerance

A protection and detection surface (PADS) concept was studied for application to composite primary aircraft structures. A Kevlar-epoxy woven face sheet with a Rohacell foam core was found to be the most effective PADS configuration among the configurations evaluated. The weight of the PADS configuration was estimated to be approximately 17 pct of the structural weight. The PADS configuration was bonded to graphite-epoxy base laminates, and up to a 70 pct improvement in compression-after-impact failure strains was observed.

Shuart, Mark J.↗
NASA NTRS1991

Quantitative nondestructive evaluation: Requirements for tomorrow's reliability

Quantitative Nondestructive Evaluation (QNDE) is the technology of measurement, analysis, and prediction of the state of material/structural systems for safety, reliability, and mission assurance. QNDE has impact on everyday life from the cars we drive, the planes we fly, the buildings we work or live in, literally to the infrastructure of our world. Here, researchers highlight some of the new sciences and technologies that are part of a safer, cost effective tomorrow. Specific technologies that are discussed are thermal QNDE of aircraft structural integrity, ultrasonic QNDE for materials characterization, and technology spinoffs from aerospace to the medical sector. In each case, examples are given of how new requirements result in enabling measurement technologies, which in turn change the boundaries of design/practice.

Heyman, Joseph S.↗
NASA NTRS1992

Hypersonic airbreathing propulsion/airframe integration

Recent interest in airbreathing hypersonic flight has centered around the need to develop advanced space launch systems which can reduce the cost of inserting payloads in orbit and make space more accessible. An effect of the thermal environment is to require the vehicle to operate at high altitudes, in very thin air, to maintain aircraft structural load limits. The high altitudes at which the hypersonic vehicle must operate give rise to the concept of an airframe integrated propulsion system to provide a much larger inlet and nozzle to process the required volume of air at low density, atmospheric conditions. In the integrated system, the forward portion of the vehicle compresses the air flow and serves as the external portion of the inlet; the aftbody completes the expansion process for the nozzle. In addition, the engine, which is contained between the body and the forebody shock wave, lends itself to a modular integration of a number of separate engines. In this manner, a relatively small engine can be defined to allow engine development in existing ground facilities.

Weidner, John P.↗
NASA NTRS1990

A Protection And Detection Surface (PADS) for damage tolerance

A protection and detection surface (PADS) concept was studied for application to composite primary aircraft structures. A Kevlar-epoxy woven face sheet with a Rohacell foam core was found to be the most effective PADS configuration among the configurations evaluated. The weight of the PADS configuration was estimated to be approximately 17 percent of the structural weight. The PADS configuration was bonded to graphite-epoxy base laminates, and up to a 70 percent improvement in compression-after-impact failure strains was observed.

Shuart, M. J.↗
NASA NTRS1991

Electro optical system to measure strains at high temperature

The measurement of strains at temperatures of the order of 1000 C has become a very important field of research. Technological advances in areas such as the analysis of high speed aircraft structures and high efficiency thermal engines require operational temperatures of this order of magnitude. Current techniques for the measurement of strains, such as electrical strain gages, are at the limit of their useful range and new methods need to be developed. Optical techniques are very attractive in this type of application because of their noncontacting nature. Holography is of particular interest because a minimal preparation of the surfaces is required. Optoelectronics holography is specially suited for this type of application, from the point of view of industrial use. There are a number of technical problems that need to be overcome to measure strains using holographic interferometry at high temperatures. Some of these problems are discussed, and solutions are given. A specimen instrumented with high temperature strains gages is used to compare the results of both technologies.

Sciammarella, Cesar A.↗
NASA NTRS1992

Aerostructural safety factor criteria

The present modification of the conventional safety factor method for aircraft structures evaluation involves the expression of deterministic safety factors in probabilistic tolerance limit ratios; these are found to involve a total of three factors that control the interference of applied and resistive stress distributions. The deterministic expression is extended so that it may furnish a 'relative ultimate safety' index that encompasses all three distribution factors. Operational reliability is developed on the basis of the applied and the yield stress distribution interferences. Industry standards are suggested to be derivable from factor selections that are based on the consequences of failure.

Verderaime, V.↗
NASA NTRS1992

New materials drive high-performance aircraft

This report shows how advanced composite materials and new processing methods are enabling lighter, lower cost aircraft structures. High-temperature polymers research will focus on systems capable of 50,000 to 100,000 hours of operation in the 212-400 F temperature range. Prospective materials being evaluated include high-temperature epoxies, toughened bismaleimides, cyanates, thermoplastics, polyimides and other polymers.

Ruhmann, Douglas C.↗
NASA NTRS1993

Flame-Retardant Diaminobenzenes Containing Phosphorus

Diamines polymerized with dianhydrides or diacyl halides to produce fire-resistant polymers. Properties of polymers useful as matrices in laminated composite-material aircraft structural components that resist fire and exhibit desirable mechanical properties as high tensile strength. Diamines used as encapsulating or potting compounds when reacted with epoxy resins. Free phosphonic acids, byproducts of synthesis of diamines used as complexing agents to extract metals from aqueous solutions or as corrosion inhibitors for metals.

Kourtides, Demetrius A.↗
NASA NTRS1992

Properties of five toughened matrix composite materials

The use of toughened matrix composite materials offers an attractive solution to the problem of poor damage tolerance associated with advanced composite materials. In this study, the unidirectional laminate strengths and moduli, notched (open-hole) and unnotched tension and compression properties of quasi-isotropic laminates, and compression-after-impact strengths of five carbon fiber/toughened matrix composites, IM7/E7T1-2, IM7/X1845, G40-800X/5255-3, IM7/5255-3, and IM7/5260 have been evaluated. The compression-after-impact (CAI) strengths were determined primarily by impacting quasi-isotropic laminates with the NASA Langley air gun. A few CAI tests were also made with a drop-weight impactor. For a given impact energy, compression after impact strengths were determined to be dependent on impactor velocity. Properties and strengths for the five materials tested are compared with NASA data on other toughened matrix materials (IM7/8551-7, IM6/1808I, IM7/F655, and T800/F3900). This investigation found that all five materials were stronger and more impact damage tolerant than more brittle carbon/epoxy composite materials currently used in aircraft structures.

Cano, Roberto J.↗
NASA NTRS1992

Mode interaction in stiffened composite shells under combined mechanical and thermal loadings

Stiffened shells of various configurations fabricated out of composite materials find extensive applications in aircraft structures. Two distinctive modes of buckling dominate structural response of stiffened panels, viz. the short-wave local mode in which the shell skin buckles essentially between the stiffeners and the long-wave overall mode in which the shell skin buckles carrying the stiffeners with it. In optimized designs, the critical stresses corresponding to these modes of buckling would be close to each other. This leads to a nonlinear mode interaction which is recognized to be the principal cause of the failure of stiffened structures. If the structure is subjected to through-the-thickness thermal gradients, then large-wave bending effects would begin to occur well below the overall critical load and these would play the role of overall imperfections. The load carrying capacity would be significantly diminished as a result of interaction of local buckling with overall thermal distortions. The analysis of this problem using standard finite element techniques can be shown to be prohibitively expensive for design iterations. A concept which would greatly facilitate the analysis of mode interaction is advanced. We note that the local buckling occurs in a more or less periodic pattern in a structure having regular spacings of stiffeners. Thus it is a relatively simple matter to analyze the local buckling and the second order effects (which are essential for modeling postbuckling phenomena) using a unit cell of the structure. Once analyzed, these dormations are embedded in a shell element. Thus, a shell element could span several half-waves of local buckling and still be able to depict local buckling effects with requisite accuracy. A major consequence of the interaction of overall buckling/bending is the slow variation of the local buckling amplitude across the structure - the phenomenon of 'amplitude modulation' - and this is accounted for in the present model by letting the scaling parameter of the local mode vary according to a 'slowly varying' function. The construction of the analytical model involves essentially two stages and these are described briefly.

Sridharan, Srinivasan↗
NASA NTRS1993

Hypersonic panel flutter in a rarefied atmosphere

Panel flutter is a form of dynamic aeroelastic instability resulting from the interaction between motion of an aircraft structural panel and the aerodynamic loads exerted on that panel by air flowing past one of the faces. It differs from lifting surface flutter in the sense that it is not usually catastrophic, the panel's motion being limited by nonlinear membrane stresses produced by the transverse displacement. Above some critical airflow condition, the linear instability grows to a limit cycle . The present investigation studies panel flutter in an aerodynamic regime known as 'free molecule flow', wherein intermolecular collisions can be neglected and loads are caused by interactions between individual molecules and the bounding surface. After collision with the panel, molecules may be reflected specularly or reemitted in diffuse fashion. Two parameters characterize this process: the 'momentum accommodation coefficient', which is the fraction of the specularly reflected molecules; and the ratio between the panel temperature and that of the free airstream. This model is relevant to the case of hypersonic flight vehicles traveling at very high altitudes and especially for panels oriented parallel to the airstream or in the vehicle's lee. Under these conditions the aerodynamic shear stress turns out to be considerably larger than the surface pressures, and shear effects must be included in the model. This is accomplished by means of distributed longitudinal and bending loads. The former can cause the panel to buckle. In the example of a simply-supported panel, it turns out that the second mode of free vibration tends to dominate the flutter solution, which is carried out by a Galerkin analysis. Several parametric studies are presented. They include the effects of (1) temperature ratio; (2) momentum accommodation coefficient; (3) spring parameters, which are associated with how the panel is connected to adjacent structures; (4) a parameter which relates compressive end load to its value which would cause classical column buckling; (5) a parameter proportional to the pressure differential between the front and back faces; and (6) initial curvature. The research is completed by an investigation into the possibility of accounting for molecular collisions, which proves to be infeasible given the speeds of current mainframe supercomputers.

Resende, Hugo B.↗
NASA NTRS1991

Development of stitching reinforcement for transport wing panels

The NASA Advanced Composites Technology (ACT) program has the objective of providing the technology required to obtain the full benefit of weight savings and performance improvements offered by composite primary aircraft structures. Achieving the objective is dependent upon developing composite materials and structures which are damage tolerant and economical to manufacture. Researchers are investigating stitching reinforcement combined with resin transfer molding to produce materials meeting the ACT program objective. Research is aimed at materials, processes, and structural concepts for application in both transport wings and fuselages, but the emphasis to date has been on wing panels. Empirical guidelines are being established for stitching reinforcement in structures designed for heavy loads. Results are presented from evaluation tests investigating stitching types, threads, and density (penetrations per square inch). Tension strength, compression strength, and compression after impact data are reported.

Palmer, Raymond J.↗
NASA NTRS1992

Automation of disbond detection in aircraft fuselage through thermal image processing

A procedure for interpreting thermal images obtained during the nondestructive evaluation of aircraft bonded joints is presented. The procedure operates on time-derivative thermal images and resulted in a disbond image with disbonds highlighted. The size of the 'black clusters' in the output disbond image is a quantitative measure of disbond size. The procedure is illustrated using simulation data as well as data obtained through experimental testing of fabricated samples and aircraft panels. Good results are obtained, and, except in pathological cases, 'false calls' in the cases studied appeared only as noise in the output disbond image which was easily filtered out. The thermal detection technique coupled with an automated image interpretation capability will be a very fast and effective method for inspecting bonded joints in an aircraft structure.

Prabhu, D. R.↗
NASA NTRS1942

Tensile and pack compressive tests of some sheets of aluminum alloy, 1025 carbon steel, and chromium-nickel steel

Tensile and compressive stress-strain curves, stress-deviation curves, and secant modulus-stress curves are given for longitudinal and transverse specimens of 17S-T, 24S-T, and 24S-RT aluminum-alloy sheet in thicknesses from 0.032 to 0.081 inch, 1025 carbon steel sheet in thicknesses of 0.054 and 0.120 inch, and chromium-nickel steel sheet in thicknesses form 0.020 to 0.0275 inch. Significant differences were found between the tensile and the compressive stress-strain curves, and also the corresponding corollary curves; similarly, differences were found between the curves for the longitudinal and transverse directions. These differences are of particular importance in considering the compressive strength of aircraft structures made of thin sheet. They are explored further for the case of compression by giving tangent modulus-stress curves in longitudinal and transverse compression and dimensionless curves of the ratio of tangent modulus to Young's modulus and of the ratio of reduced modulus for a rectangular section to Young's modulus, both plotted against the ratio of stress to secant yield strength.

Atchison, C S↗
NASA NTRS1946

Standard nomenclature for airspeeds with tables and charts for use in calculation of airspeed

Symbols and definition of various airspeed terms that have been adopted as standard by the NACA subcommittee on aircraft structural design are presented. The equations, charts, and tables required in the evaluation of true airspeed, calibrated airspeed, equivalent airspeed, impact and dynamic pressures, and Mach and Reynolds numbers have been compiled. Tables of the standard atmosphere to an altitude of 65,000 feet and a tentative extension to an altitude of 100,000 feet are given along with the basic equations and constants on which both the standard atmosphere and the tentative extension are based.

Aiken, William S , Jr↗
NASA NTRS1957

Near Noise Field of a Jet-Engine Exhaust

Aircraft structures located in the near noise field of a jet engine are subjected to extremely high fluctuating pressures that may cause structural fatigue. Studies of such structures have been limited by lack of knowledge of the loadings involved. The acoustic near field produced by the exhaust of a stationary turbojet engine having a high pressure ratio was measured for a single operating condition without burning. The maximum overall sound pressure without afterburning was found to be about 42 pounds per square foot along the jet boundary in the region immediately downstream of the jet-nozzle exit. With afterburning maximum sound pressure was increased by 50 percent. The sound pressures without afterburning were obtained on a constant percentage band width basis in the frequency range from 350 to 700 cps. Cross-correlation measurements with microphones were made for a range of jet velocities at locations along the jet and at a distance from the jet. In general, little change in the correlation curves was found as a function of jet velocity or frequency-band width.

Howes, Walton L↗