Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ATTITUDES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

Attitude Control Tradeoff Study Between the Use of a Flexible Beam and a Tether Configuration for the Connection of Two Bodies in Orbit

Sometimes it is necessary to mount a payload remotely from the main body of a spacecraft or space station. The reasons for this vary from vibration isolation to avoidance of measurement contamination. For example the SP-100 project, which grew out of the increased interest in nuclear power in space for space stations and for deep space explorations, requires separation of the nuclear reactor from the user because of vibration, heat and radiation. The different attitude control problems for beam and tether configurations are discussed. The beam configuration uses a conservative design approach. The vibration, beam flexibility and deployment concerns are analyzed. The tether configuration offers some very attractive design features, but not without several thorny problems. These problems are analyzed. One configuration will be recommended for the main thrust of the SP-100 design effort based on attitude control considerations.

Graff, S. H.↗

Comparing attitude control effectiveness for actuators on two bodies of a six body model of a flexible spacecraft with that for actuators restricted to a single body

A ten rigid body model of a prototype flexible space platform was approximated by a six body model to facilitate comparison of attitude control effectiveness for actuators on two bodies with control effectiveness for actuators restricted to a single body of the same model. Actuators and sensors were found to be required on two of the six bodies for effective attitude control.

Chichester, F. D.↗

An optimized rotation-axis model-following controller for STS orbiter attitude maneuvers

This paper describes a new controller for automatic attitude maneuvers of the Space Shuttle Orbiter. The controller incorporates a new solution algorithm for partially linearized, fuel-optimal maneuvers for RCS jet controlled spacecraft. These solutions provide model trajectories and jet commands that are easily tracked using a feed-forward, feedback controller structure. The result is a substantial performance improvement over the current Orbiter attitude maneuver controller. The paper discusses optimal maneuvers for this type of vehicle, giving detail of the solution algorithm. Closed-loop controller design and implementation is discussed. Detailed performance results are presented.

Redding, D. C.↗

Response of GAS payload (G345 and G347) temperatures to various orbiter flight attitudes

At the beginning of the Get-Away Special (GAS) flight program, the GAS Project flew a Flight Verification Payload on STS-3 to make measurements of the vibrations, acoustic and magnetic environments of the canister, and to obtain thermal profiles of internal and external components of the GAS system. These data were used to verify pre-flight thermal models of the GAS system and results have been published in a GSFC Technical Note, X-732-83-8 (Butler, 1983). On somewhat later flights of the Orbiter, STS-7 and STS-8, the Naval Research Laboratory and the Goddard Space Flight Center jointly developed and flew a GAS payload whose primary objective was to evaluate the performance of ultraviolet-sensitive (Schumann) photographic emulsions in the Orbiter environment, including pre-flight integration, on-orbit exposure to the ambient environment of the Orbiter bay and post-flight conditions before removal of the experiment from the vehicle. These emulsions, used in spectrographs to record solar radiations with wavelengths between 100 A and 2000 A, have low gelatin content and no protective gelatin overcoating in order to maximize their UV sensitivity. Consequently, they are extremely sensitive to environmental conditions. Furthermore, they are exposed directly to space during the observations because any intervening protective window or lense would completely absorb the radiations to be studied. which was prepared at the Naval Research Laboratory under the direction of Robert Kreplin (Kreplin et al., 1984 a) also included two thermal sensors, whose output was recorded once an hour with a precision of 0.7O C. The experiment operated nominally on both missions and provided important data confirming that W - sensitive emulsions could tolerate integration and flight on the Shuttle with relatively little deterioration. The results of these studies have already been reported (Kreplin et al, 1984 b). The temperature measurements also were recorded successfully and are the basis for this paper. They are a useful complement to the thermal observations made on STS-3 and provide additional insight into the reaction of a payload to typical thermal environments that GAS experiments are subject to. Our GAS experiment and the circumstances of its flights were particularly useful in terms of modeling the thermal response of the GAS canister and our instrument. The Orbiter was held (except for interruptions for star tracker alignment, satellite deployments, etc., in specific attitudes for sufficiently long periods of time that the thermal response of the instrument to each attitude was well measured. Two types of GAS canister end cap, one, the insulated end cap and the other a silverized teflon covered end-cap, were used on the two flights so that a direct comparison of the thermal performance of the two types was obtained. This report is an attempt to compare these observations with a simple thermal model of the instrument in the GAS canister in order to assess whether such simple models can be useful to experimenters in predicting the thermal response of their payloads.

Werner M. Neuper↗

Nonlinear filtering for spacecraft attitude estimation

Nonlinear filtering techniques are applied to spacecraft attitude estimation using quaternion parameterization for the attitude kinematics. By replacing the angular velocity vector by the gyro output vector, a state dependent noise vector is introduced in the seven-dimensional system equations. The resulting conditional probability density function from the Ito differential rule is governed by the Fokker Planck partial differential equation which is approximated by the second order mean and covariance differential equations. In order to minimize computer loading, the covariance propagation is carried out in six-dimensional state space using a matrix transformation. The star tracker data is used to update the covariance matrix in the seven-dimensional space. The algorithm is simulated for an earth pointing spacecraft mission, using Monte Carlo samples of gyro and star measurements. The performance of the second order filter is compared with the extended Kalman Filter through several simulation runs and drift rates have been identified.

Vathsal, S.↗

High speed reaction wheels for satellite attitude control and energy storage

The combination of spacecraft attitude control and energy storage (ACES) functions in common hardware, to synergistically maintain three-axis attitude control while supplying electrical power during earth orbital eclipses, allows the generation of control torques by high rotating speed wheels that react against the spacecraft structure via a high efficiency bidirectional energy conversion motor/generator. An ACES system encompasses a minimum of four wheels, controlling power and the three torque vectors. Attention is given to the realization of such a system with composite flywheel rotors that yield high energy density, magnetic suspension technology yielding low losses at high rotational speeds, and an ironless armature permanent magnet motor/generator yielding high energy conversion efficiency.

Studer, P.↗

Tetrahedron array of reaction wheels for attitude control and energy storage

A spacecraft subsystem, working in conjunction with a solar array, which provides 3-axis attitude control as well as some power system functions is described. Four flywheels, driven by variable-field d.c. motors and arranged in a tetrahedron configuration, are employed. In sunlight, the system provides voltage regulation while the wheels are accelerated to some maximum speed. In the dark, the motors become flywheel-driven generators which provide regulated power to other spacecraft electrical loads. A microprocessor is used to compute field current levels for each of the 4 motor/generators, based on measurements of the system voltage level, the flywheel speeds, and the attitude control torques desired.

Flatley, T. W.↗

Helicopter attitude stabilization using individual-blade-control

A theoretical study is presented on the application of the Individual-Blade-Control concept to helicopter attitude stabilization. The design of a system controlling blade flapping dynamics, and related testing of the system on a model rotor in the wind tunnel, is described. The control inputs considered are blade pitch changes proportional to blade flapping acceleration, velocity, and displacement. The effect of such a system on helicopter rotor damping-in-pitch, and angle-of-attack stability is then evaluated. It is shown that helicopter attitude stabilization is achieved, with a corresponding improvement in flying qualities.

Ham, N. D.↗

Cockpit resource management - Exploring the attitude-performance linkage

Measured attitudes regarding cockpit management were contrasted for pilots whose line flying performance was independently evaluated by check airmen as above or below average. A highly significant discriminant function was obtained indicating that these attitudes are significant predictors of behavior. The performance of 95.7 percent of the pilots was correctly classified by the analysis. Implications of the results for cockpit resource management training and pilot selection are discussed.

Helmreich, R. L.↗

Spacecraft attitude control momentum requirements analysis

The relationship between attitude and angular momentum control requirements is derived for a fixed attitude, Earth orbiting spacecraft with large area articulating appendages. Environmental effects such as gravity gradient, solar radiation pressure, and aerodynamic forces arising from a dynamic, rotating atmosphere are examined. It is shown that, in general, each environmental effect contributes to both cyclic and secular momentum requirements both within and perpendicular to the orbit plane. The gyroscopic contribution to the angular momentum control requirements resulting from a rotating, Earth oriented spacecraft is also discussed. Special conditions are described where one or more components of the angular momentum can be made to vanish, or become purely cyclical. Computer generated plots for a candidate space station configuration are presented to supplement the analytically derived results.

Robertson, Brent P.↗

NUSAT 1 attitude determination

This paper presents the methods for attitude determination using the static wide angle field of view sensors of NUSAT 1. Some supporting analysis and operational results are given. The system gives at best a crude attitude determination.

Talaga, Paul↗

Applications software supporting the Spartan Attitude Control System

The native software supporting a single mission for the Spartan Attitude Control System can require up to 40,000 lines of code. Most of this must be rewritten for each mission. Control system engineers use an array of Applications Software Packages residing in ground computers to write each mission's flight software. These Applications Packages are written in the 'C' programming language and run under the UNIX Operating System. This paper discusses each of the Attitude Control Applications Software Packages, and describes the purpose and design of each.

Stone, R. W.↗

Cosmic Background Explorer (COBE) transfer orbit attitude control system

The Cosmic Background Explorer (COBE) spacecraft will be launched by the Shuttle from Vandenberg AFB into a 300 km altitude, 99 deg inclination, 6 a.m. or 6 p.m. ascending node orbit. After release from the Remote Manipulator System (RMS) arm, an on-board monopropellant hydrazine propulsion system will raise the orbit altitude to 900 km. The spacecraft continuously spins during transfer orbit operations with the spin axis nominally horizontal and in or near the orbit plane. The blowdown propulsion system consists of twelve 5 lb thrusters (3 'spin', 3 'despin', and 6 'axial') with the latter providing initially 30 lb of force parallel to the spin axis for orbit raising. The spin/despin jets provide a constant roll rate during the transfer orbit phase of the mission and the axials control pitch and yaw. The axial thrusters are pulsed on for attitude control during coast periods and are normally on- and off-modulated for control during orbit raising. Attitude sensors employed in the control loops include an array of two-axis digital sun sensors and three planar earth scanners for position measurements, as well as six gyroscopes for rate information. System redundancy is achieved by means of unique three-axes-in-a-plane geometry. This triaxial concept results in a fail-safe operational system with no performance degradation for many different component failure modes.

Placanica, Samuel J.↗

GRO attitude control and determination

Design features of the attitude control and determination (ACAD) system for the Gamma Ray Observatory (GRO) that will eventually be launched on the Shuttle are described. A tabulation of the ACAD system components is provided and the various standby and normal pointing operational modes of the system are summarized. The system software and sensors will maintain a quaternion model of the GRO attitude on the bases of kinematic equations and inertial data. The software is standardized and has previously been used on the Solar Maximum Mission and Landsat-D. Details of the processing components, redundant electronics for sensor processing, data handling and actuator control are outlined and illustrated with block diagrams. Tests applied to validate the ACAD design are outlined, as are ground support which will be implemented once the GRO is launched.

Jerkovsky, W.↗

Determining Spacecraft Attitude For Planetary Mapping

New algorithm calculates attitude with accuracy to spare. Report describes algorithm for use in determining attitude of spacecraft from incremental-angle output of strapdown gyroscope and star-scanner measurements. Highlights detail of underlying theories and strategies. Presents results of simulation to demonstrate capability of algorithm, and discusses possible applications.

Huang, Whitak H.↗

Three axis attitude control system

A three-axis attitude control system for an orbiting body comprised of a motor driven flywheel supported by a torque producing active magnetic bearing is described. Free rotation of the flywheel is provided about its central axis and together with limited angular torsional deflections of the flywheel about two orthogonal axes which are perpendicular to the central axis. The motor comprises an electronically commutated DC motor, while the magnetic bearing comprises a radially servoed permanent magnet biased magnetic bearing capable of producing cross-axis torques on the flywheel. Three body attitude sensors for pitch, yaw and roll generate respective command signals along three mutually orthogonal axes (x, y, z) which are coupled to circuit means for energizing a set of control coils for producing torques about two of the axes (x and y) and speed control of the flywheel about the third (z) axis. An energy recovery system, which is operative during motor deceleration, is also included which permits the use of a high-speed motor to perform effectively as a reactive wheel suspended in the magnetic bearing.

Studer, Philip A.↗

Model reference adaptive attitude control of spacecraft using reaction wheels

A nonlinear model reference adaptive control law for large angle rotational maneuvers of spacecraft using reaction wheels in the presence of uncertainty is presented. The derivation of control law does not require any information on the values of the system parameters and the disturbance torques acting on the spacecraft. The controller includes a dynamic system in the feedback path. The control law is a nonlinear function of the attitude error, the rate of the attitude error, and the compensator state. Simulation results are prsented to show that large angle rotational maneuvers can be performed in spite of the uncertainty in the system.

Singh, Sahjendra N.↗

Attitude control of a three rotor gyrostat in the presence of uncertainty

A nonlinear control law for large angle rotational maneuvers of spacecraft using reaction wheels in the presence of uncertainty is presented. The derivation of this suboptimal control law does not require any information on the values of the system parameters and the disturbance torques acting on the spacecraft. The controller includes a dynamic system in the feedback path. The control law is a nonlinear function of the attitude error, the rate of the attitude error and the compensator state. Simulation results are presented to show that large angle rotational maneuvers can be performed in spite of the uncertainty in the system.

Singh, Sahjendra N.↗