Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “wind tunnel experiments”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Design and calibration of the mixing layer and wind tunnel

A detailed account of the design, assembly and calibration of a wind tunnel specifically designed for free-shear layer research is contained. The construction of this new facility was motivated by a strong interest in the study of plane mixing layers with varying initial and operating conditions. The Mixing Layer Wind tunnel is located in the Fluid Mechanics Laboratory at NASA Ames Research Center. The tunnel consists of two separate legs which are driven independently by centrifugal blowers connected to variable speed motors. The blower/motor combinations are sized such that one is smaller than the other, giving maximum flow speeds of about 20 and 40 m/s, respectively. The blower speeds can either be set manually or via the Microvax II computer. The two streams are allowed to merge in the test section at the sharp trailing edge of a slowly tapering splitter plate. The test section is 36 cm in the cross-stream direction, 91 cm in the spanwise direction and 366 cm in length. One test section side-wall is slotted for probe access and adjustable so that the streamwise pressure gradient may be controlled. The wind tunnel is also equipped with a computer controlled, three-dimensional traversing system which is used to investigate the flow fields with pressure and hot-wire instrumentation. The wind tunnel calibration results show that the mean flow in the test section is uniform to within plus or minus 0.25 pct and the flow angularity is less than 0.25 deg. The total streamwise free-stream turbulence intensity level is approximately 0.15 pct. Currently the wind tunnel is being used in experiments designed to study the three-dimensional structure of plane mixing layers and wakes.

Bell, James H.↗
NASA NTRS1990

Turbulence and shear stress measurements in hypersonic flow

An assessment has been made of the potential for hot wire and laser anemometer measurements of turbulent fluctuations in hypersonic flow fields. The results of laser velocimeter experiments conducted in two hypersonic wind tunnels are reported and comparisons made with previous hot wire turbulence measurements. A new concept for the measurement of the compressible shear stress terms which combines the attributes of both hot wire and laser anemometry is presented.

Owen, F. K.↗
NASA NTRS1990

Transition and turbulence measurements in hypersonic flows

This paper reviews techniques for transitional- and turbulent-flow measurements and describes current research in support of turbulence modeling. Special attention is given to the potential of applying hot wire and laser velocimeter to measuring turbulent fluctuations in hypersonic flow fields. The results of recent experiments conducted in two hypersonic wind tunnels are presented and compared with previous hot-wire turbulence measurements.

Owen, F. K.↗
NASA NTRS1991

V/STOL gets a lift

The concept of a supersonic STOVL that could offer enhanced mission capability, survivability, operational flexibility, and utility over conventional aircraft is presented. Emphasis is currently on design studies, CFD work, small- and large-scale wind tunnel tests, simulation activities, flight experiments, and ground environment experiments. Propulsion system technology centers about the adaptation of existing or off-the-shelf engines. Concepts under study include separate flow in hover, gas-driven lift fan, and shaft-driven lift fan. NASA is examining generic valve and ducting configurations with airflow at ambient temperature and at temperatures up to 1000 F to gather pressure loss and heat transfer data. Advanced civil rotorcraft technologies examined include high-efficiency/dual-mode components such as torque converters; lightweight, quiet transmissions; and variable geometry power turbines; along with dual-function or convertible engines.

Biesiadny, Tom↗
NASA NTRS1991

Meeting Review: Airborne Aerosol Inlet Workshop

Proceedings from the Airborne Aerosol Inlet Workshop are presented. The two central topics of discussion were the role of aerosols in atmospheric processes and the difficulties in characterizing aerosols. The following topics were discussed during the working sessions: airborne observations to date; identification of inlet design issues; inlet modeling needs and directions; objectives for aircraft experiments; and future laboratory and wind tunnel studies.

Baumgardner, Darrel↗
NASA NTRS1992

An assessment of particle velocimetry potential in hypersonic flow

Future progress in the computation of hypersonic flow fields is restricted by the need for a reliable turbulence modeling data base which could be used for the development of empirical models for use in numerical codes. Currently, there are few compressible flow measurements which could be used for this purpose. Procedures for hot wire measurements in hypersonic flows are presently outlined, and assessments are made of the potential for hot wire and laser velocimeter measurements of turbulent fluctuations in hypersonic flow fields. The results of recent experiments conducted in two hypersonic wind tunnels will be presented and comparisons made with previous hot wire turbulence measurements.

Owen, F. K.↗
NASA NTRS2002

Virtual Shaping of a Two-dimensional NACA 0015 Airfoil Using Synthetic Jet Actuator

The Aircraft Morphing Program at NASA Langley envisions an aircraft without conventional control surfaces. Instead of moving control surfaces, the vehicle control systems may be implemented with a combination of propulsive forces, micro surface effectors, and fluidic devices dynamically operated by an intelligent flight control system to provide aircraft maneuverability over each mission segment. As a part of this program, a two-dimensional NACA 0015 airfoil model was designed to test mild maneuvering capability of synthetic jets in a subsonic wind tunnel. The objective of the experiments is to assess the applicability of using unsteady suction and blowing to alter the aerodynamic shape of an airfoil with a purpose to enhance lift and/or to reduce drag. Synthetic jet actuation at different chordwise locations, different forcing frequencies and amplitudes, under different freestream velocities are investigated. The effect of virtual shape change is indicated by a localized increase of surface pressure in the neighborhood of synthetic jet actuation. That causes a negative lift to the airfoil with an upper surface actuation. When actuation is applied near the airfoil leading edge, it appears that the stagnation line is shifted inducing an effect similar to that caused by a small angle of attack to produce an overall lift change.

Chen, Fang-Jenq↗
NASA NTRS2015

Near-Field Acoustic Power Level Analysis of F31/A31 Open Rotor Model at Simulated Cruise Conditions, Technical Report II

Near-field acoustic power level analysis of F31A31 open rotor model has been performed to determine its noise characteristics at simulated cruise flight conditions. The non-proprietary parts of the test data obtained from experiments in the 8x6 supersonic wind tunnel were provided by NASA-Glenn Research Center. The tone and broadband components of total noise have been separated from raw test data by using a new data analysis tool. Results in terms of sound pressure levels, acoustic power levels, and their variations with rotor speed, freestream Mach number, and input shaft power, with different blade-pitch setting angles at simulated cruise flight conditions, are presented and discussed. Empirical equations relating models acoustic power level and input shaft power have been developed. The near-field acoustic efficiency of the model at simulated cruise conditions is also determined. It is hoped that the results presented in this work will serve as a database for comparison and improvement of other open rotor blade designs and also for validating open rotor noise prediction codes.

Broadband↗
NASA NTRS2015

Time-Accurate Unsteady Pressure Loads Simulated for the Space Launch System at Wind Tunnel Conditions

A transonic flow field about a Space Launch System (SLS) configuration was simulated with the Fully Unstructured Three-Dimensional (FUN3D) computational fluid dynamics (CFD) code at wind tunnel conditions. Unsteady, time-accurate computations were performed using second-order Delayed Detached Eddy Simulation (DDES) for up to 1.5 physical seconds. The surface pressure time history was collected at 619 locations, 169 of which matched locations on a 2.5 percent wind tunnel model that was tested in the 11 ft. x 11 ft. test section of the NASA Ames Research Center's Unitary Plan Wind Tunnel. Comparisons between computation and experiment showed that the peak surface pressure RMS level occurs behind the forward attach hardware, and good agreement for frequency and power was obtained in this region. Computational domain, grid resolution, and time step sensitivity studies were performed. These included an investigation of pseudo-time sub-iteration convergence. Using these sensitivity studies and experimental data comparisons, a set of best practices to date have been established for FUN3D simulations for SLS launch vehicle analysis. To the author's knowledge, this is the first time DDES has been used in a systematic approach and establish simulation time needed, to analyze unsteady pressure loads on a space launch vehicle such as the NASA SLS.

Alter, Stephen J.↗
NASA NTRS2021

Hypersonic Boundary-Layer Transition on Blunted Cones at Angle of Attack

Experimental studies of cones at several high-speed facilities have demonstrated that, for small nosetip bluntness, transition onset over a circular cone moves upstream along the leeward side and downstream along the windward side, but this trend may be reversed at large bluntness values, where transition onset moves downstream along the leeward side and upstream along the windward side. A theoretical and numerical investigation is performed to characterize the effects of nose bluntness on disturbance amplification over the circular cone for several angles of attack, with the goal of understanding the potential physical mechanisms behind the experimental observations. The three-dimensional laminar basic states over a 1.5 m long, 7-degree half-angle cone with 9.525 mm nosetip radius are computed for selected angles of attack values and freestream conditions that are selected to match the Mach 10 experiments conducted within the Hypervelocity Wind Tunnel 9 at the Arnold Engineering Development Complex (AEDC). The solutions at a freestream unit Reynolds number of 17.1 million per meter are used to perform detailed instability analyses for angles of attack equal to 0, 1, 3, and 5 degrees. Results indicate that the linear amplification of stationary crossflow waves along inflection lines may begin to influence transition along the acreage of the cone for angles of attack equal to or larger than 5 degrees. The measured trend in transition front with respect to increasing angle of attack is found to be consistent with the predicted increase in the amplification factors for Mack mode disturbances along the streamline trajectories. The increase in Mack mode amplification along the windward ray for higher angles of attack is shown to be the result of a progressively earlier entropy-layer swallowing. Computations also indicate that the transition amplification factor along the windward ray is not constant and increases with the angle of attack and that the transition #-factors along the leeward ray are rather small. The nonmodal analysis for zero degrees angle of attack shows that entropy-layer disturbances with appreciably strong energy growth can coexist with Mack mode instabilities at the measured transition location.

boundary layer transition↗
NASA NTRS2021

Hypersonic Boundary-Layer Transition on Blunted Cones at Angle of Attack

Experimental studies of cones at several high-speed facilities have demonstrated that, for small nosetip bluntness, transition onset over a circular cone moves upstream along the leeward side and downstream along the windward side, but this trend may be reversed at large bluntness values, where transition onset moves downstream along the leeward side and upstream along the windward side. A theoretical and numerical investigation is performed to characterize the effects of nose bluntness on disturbance amplification over the circular cone for several angles of attack, with the goal of understanding the potential physical mechanisms behind the experimental observations. The three-dimensional laminar basic states over a 1.5 m long, 7-degree half-angle cone with 9.525 mm nosetip radius are computed for selected angles of attack values and freestream conditions that are selected to match the Mach 10 experiments conducted within the Hypervelocity Wind Tunnel 9 at the Arnold Engineering Development Complex (AEDC). The solutions at a freestream unit Reynolds number of 17.1 million per meter are used to perform detailed instability analyses for angles of attack equal to 0, 1, 3, and 5 degrees. Results indicate that the linear amplification of stationary crossflow waves along inflection lines may begin to influence transition along the acreage of the cone for angles of attack equal to or larger than 5 degrees. The measured trend in transition front with respect to increasing angle of attack is found to be consistent with the predicted increase in the amplification factors for Mack mode disturbances along the streamline trajectories. The increase in Mack mode amplification along the windward ray for higher angles of attack is shown to be the result of a progressively earlier entropy-layer swallowing. Computations also indicate that the transition amplification factor along the windward ray is not constant and increases with the angle of attack and that the transition #-factors along the leeward ray are rather small. The nonmodal analysis for zero degrees angle of attack shows that entropy-layer disturbances with appreciably strong energy growth can coexist with Mack mode instabilities at the measured transition location.

Boundary Layer Transition↗
NASA NTRSDate not supplied

Computational Investigation of the Effect of Chemistry on Mars Supersonic Retropropulsion Environments

Retropropulsion ground tests require significant compromises on physical scale, instrumentation, configuration, and environments. Matching the full Martian environment is simply not possible on Earth. Ground tests of retropropulsion configurations thus far have neglected effects of chemistry due to physical constraints of wind tunnel models and facilities; most experiments use inert simulant gases at relatively low temperatures. As such, a strong reliance on high-fidelity computational analyses is required to expand the knowledge of retropropulsion aerodynamics. In this work, we investigate the effects of chemistry using scale-resolving computational fluid dynamics (CFD) with finite-rate chemistry and a graphics processing unit (GPU)-enabled implementation of the NASA FUN3D flow solver on a human-scale Mars lander concept at supersonic freestream conditions. Results are compared to previous perfect gas simulations.

retropropulsion↗
NASA NTRSDate not supplied

Computational Investigation of the Effect of Chemistry on Mars Supersonic Retropropulsion Environments

Retropropulsion ground tests require significant compromises on physical scale, instrumentation, configuration, and environments. Matching the full Martian environment is simply not possible on Earth. Ground tests of retropropulsion configurations thus far have neglected effects of chemistry due to physical constraints of wind tunnel models and facilities; most experiments use inert simulant gases at relatively low temperatures. As such, a strong reliance on high-fidelity computational analyses is required to expand the knowledge of retropropulsion aerodynamics. In this work, we investigate the effects of chemistry using scale-resolving computational fluid dynamics (CFD) with finite-rate chemistry and a graphics processing unit (GPU)-enabled implementation of the NASA FUN3D flow solver on a human-scale Mars lander concept at supersonic freestream conditions. Results are compared to previous perfect gas simulations.

retropropulsion↗
NASA NTRSDate not supplied

Computational Investigation of the Effect of Chemistry on Mars Retropropulsion Environments using a Massively Parallel GPU Approach

In this work, we investigate the effects of chemistry on a human-scale Mars lander concept using scale-resolving computational fluid dynamics (CFD) with finite-rate chemistry and a graphics processing unit (GPU)-enabled implementation of the NASA FUN3D flow solver, enabling run-times of a few days for the simulations presented. Simulations are carried out on Summit at Oak Ridge Leadership Computing Facility using thousands of GPUs. Retropropulsion ground tests require significant compromises on physical scale, instrumentation, configuration, and environments. Ground tests of retropropulsion configurations thus far have neglected effects of chemistry due to physical constraints of wind tunnel models and facilities; most experiments use inert simulant gases at low temperatures. As such, a strong reliance on high-fidelity computational analyses such as those presented in this work is required to expand the knowledge of retropropulsion aerodynamics. An overview of the GPU approach will be presented. Results are compared to a previous scaled perfect gas (air) campaign.

retropropulsion↗
NASA NTRS1986

Feasibility study of optical boundary layer transition detection method

A high sensitivity differential interferometer was developed to locate the region where the boundary layer flow undergoes transition from laminar to turbulent. Two laboratory experimental configurations were used to evaluate the performance of the interferometer: open shear layer, and low speed wind tunnel turbulent spot configuration. In each experiment, small temperature fluctuations were introduced as the signal source. Simultaneous cold wire measurements were compared with the interferometer data. The comparison shows that the interferometer is sensitive to very weak phase variations in the order of 0.001 the laser wavelength. An attempt to detect boundary layer transition over a flat plate at NASA-Langley Unitary Supersonic Wind Tunnel using the interferometer system was performed. The phase variations during boundary layer transition in the supersonic wind tunnel were beyond the minimum signal-to-noise level of the instrument.

Azzazy, M.↗
NASA NTRS1982

Transonic pressure measurements and comparison of theory to experiment for three arrow-wing configurations

Wind tunnel tests of arrow-wing body configurations consisting of flat, twisted, and cambered twisted wings, as well as a variety of leading and trailing edge control surface deflections, were conducted at Mach numbers from 0.4 to 1.05 to provide an experimental pressure data base for comparison with theoretical methods. Theory to experiment comparisons of detailed pressure distributions were made using state of the art attached flow methods. Conditions under which these theories are valid for these wings are presented.

Manro, M. E.↗
NASA NTRS1986

Future requirements of wind tunnels for Computational Fluid Dynamics code verification

The role of experiment in the development of Computational Fluid Dynamics (CFD) for external aerodynamic flow-field prediction is discussed. Requirements for code verification from two sources pacing the development of CFD are described: (1) the need for developing adequate flow modeling, and (2) the need for establishing confidence in the use of CFD for predicting complex flows. The type of data needed to meet these needs differs in detail and scope and leads to definite wind tunnel requirements. Recent examples of testing to assess and develop turbulence models, and to verify code development are used to establish future requirements of wind tunnel testing for CFD verification.

Marvin, J. G.↗
NASA NTRS2001

National Transonic Facility Wall Pressure Calibration Using Modern Design of Experiments (Invited)

The Modern Design of Experiments (MDOE) has been applied to wind tunnel testing at NASA Langley Research Center for several years. At Langley, MDOE has proven to be a useful and robust approach to aerodynamic testing that yields significant reductions in the cost and duration of experiments while still providing for the highest quality research results. This paper extends its application to include empty tunnel wall pressure calibrations. These calibrations are performed in support of wall interference corrections. This paper will present the experimental objectives, and the theoretical design process. To validate the tunnel-empty-calibration experiment design, preliminary response surface models calculated from previously acquired data are also presented. Finally, lessons learned and future wall interference applications of MDOE are discussed.

Underwood, Pamela J.↗