Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface conditioning”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
NASA NTRS2023

Venus Surface Environmental Chamber Test of SiC JFET-R Multi-Chip Circuit Board

This poster describes a first attempt to demonstrate a multi-chip prototype lander control and sensor signal digitization electronics circuit board comprised of ten NASA Glenn IC Generation 11 SiC JFET-R IC chips in 460 °C, 9.4 MPa harsh Venus surface conditions. The lander circuit ceased electrical operation prematurely at 107 °C as the Venus chamber heated up. Optical and SEM post-test inspections indicate fatal dielectric cracks occurred on only one of the ten SiC chips.

silicon carbide↗
NASA NTRS2024

Dust Model Sensitivity to Dust Source Mask, Sandblasting Efficiency, Air Density, and Land Use: Implications for Model Improvement

This study compares dust storm simulations using two commonly adopted methods for representing four important dust emission parameters. Compared to a dynamic dust source mask based on land use and vegetation cover, a static mask based solely on land use overestimates dust concentration and optical depth by a factor of 2, besides generating spurious emissions. The results reinforce that seasonal variations in vegetation cover can significantly affect dust emissions. For sandblasting efficiency, a clay-dependent semiempirical expression produces 10 times more dust than a physics-based expression. Simulations using model-predicted versus a fixed constant for air density differ by only 8%. However, this difference could range between 12 and 22% for annual simulations over global dust source regions. Simulations with updated versus old land use data, using the same dust source mask, differ twofold, indicating the significant impact of land use change on regional dust emission in central Arizona. The differences in the pairs of these simulations are generally larger than the uncertainty due to meteorology. The simulations align better with observation when using the dynamic dust source mask, the physics-based sandblasting efficiency, and the up-to-date land use data. Given the high sensitivity of dust to surface conditions, the results discussed have implications for improving the dust cycle in weather and climate models and for interpreting model intercomparisons.

Dust-emission source↗
NASA NTRSDate not supplied

Additive Manufacturing and Experimental Characterization of Nickel-Titanium Shape-Memory Alloy Wick Structures and Heat Pipes for Spacecraft Thermal Control

Shape memory alloys (SMA), such as those based on nickel-titanium (NiTi), are increasingly being applied as multifunctional spacecraft components. For thermal management applications, NiTi flow tubing hinges and self-deploying loop heat pipes have been demonstrated. Emerging additive manufacturing (AM) processes are enabling more complex SMA devices than can be formed from conventional plain wire, tubing, and sheet stock materials. This paper presents our progress toward applying powder bed fusion AM to producing porous NiTi wicks and NiTi-H2O heat pipes, which could be embedded in thermally deploying radiators for spacecraft thermal management. AM near-equiatomic NiTi (55.1 wt% Ni) porous wick specimens were produced with a range of deposition parameters. Transient acetone rate-of-rise experiments were performed to estimate wick permeability (K) and average pore radius (r_pore) values and identify parameter sets with high capillary performance. Surface treatments were evaluated to achieve hydrophilic wick structures. Evaluated treatments included chemical oxide growth with H2O2, oxide and sodium titanate growth with NaOH solution, and ultrasonic cleaning with specialty detergents that can remove hydrocarbon contaminants. The most durable hydrophilic surface conditions were obtained with the NaOH treatment. High performing wick deposition parameters were used to produce a full AM NiTi heat pipe, which was treated with NaOH solution to activate the wick. This heat pipe was operated on a test stand in the inverted configuration (upper evaporator and lower condenser), and demonstrated stable nearly isothermal operation for 150 hrs.

Thermal management↗
NASA NTRSDate not supplied

Additive Manufacturing and Experimental Characterization of Nickel-Titanium Shape-Memory Alloy Wick Structures and Heat Pipes for Spacecraft Thermal Control

Shape memory alloys (SMA), such as those based on nickel-titanium (NiTi), are increasingly being applied as multifunctional spacecraft components. For thermal management applications, NiTi flow tubing hinges and self-deploying loop heat pipes have been demonstrated. Emerging additive manufacturing (AM) processes are enabling more complex SMA devices than can be formed from conventional plain wire, tubing, and sheet stock materials. This paper presents our progress toward applying powder bed fusion AM to producing porous NiTi wicks and NiTi-H2O heat pipes, which could be embedded in thermally deploying radiators for spacecraft thermal management. AM near-equiatomic NiTi (55.1 wt% Ni) porous wick specimens were produced with a range of deposition parameters. Transient acetone rate-of-rise experiments were performed to estimate wick permeability (K) and average pore radius (r_pore) values and identify parameter sets with high capillary performance. Surface treatments were evaluated to achieve hydrophilic wick structures. Evaluated treatments included chemical oxide growth with H2O2, oxide and sodium titanate growth with NaOH solution, and ultrasonic cleaning with specialty detergents that can remove hydrocarbon contaminants. The most durable hydrophilic surface conditions were obtained with the NaOH treatment. High performing wick deposition parameters were used to produce a full AM NiTi heat pipe, which was treated with NaOH solution to activate the wick. This heat pipe was operated on a test stand in the inverted configuration (upper evaporator and lower condenser), and demonstrated stable nearly isothermal operation for 150 hrs.

Thermal management↗
NASA NTRSDate not supplied

The BioSensor Instrument Beyond LEIA: a Versatile Platform for Lunar Biology

Introduction: The BioSensor is a deep-space-compatible automated microfluidic culturing instrument. While originally designed to measure the effects of deep space radiation on yeast growth for the BioSentinel mission, it has the potential to host a diverse range of life science experiments with single- and/or multi-celled organisms and can be adapted to interface with a diverse range of platforms in both crewed and uncrewed settings. It is therefore a leading candidate for hosting life sciences experimentation associated with a lunar surface habitat. BioSensor design: The function of the BioSensor is to monitor the growth and metabolic activity of samples in batch fluidic culture, without the need for crew involvement. The current configuration houses organisms in 16 wells within 16 microfluidic cards, accommodating a total of 256 samples, replicates, and controls. Each well has an optical system including three LEDs and a photodiode detector to measure absorbance at three wavelengths, enabling measurement of optical density, color change in dyes such as alamarBlue, and bioproduction of pigmented compounds. Organisms are loaded into fluidic wells and air-dried for storage during integration, launch, and transit, then activated by the introduction of culture medium from storage bags via manifolds that fill one card at a time. Temperature is controlled by individual card heaters, and timing of all activities (fluidics fills, optical measurements, temperatures) is directed by an experiment script. The self-contained BioSensor payload is roughly 4U in volume; with electrical/mechanical/thermal interface, e.g. for operation on ISS or a lunar lander, as well as a linear energy-transfer (LET) charged-particle radiation spectrometer, the entire system is closer to 6U. BioSentinel and LEIA: Flown on the ISS and in a deep-space free flyer for BioSentinel, the BioSensor has been modified for use in the LEIA mission, including improvements to reduce the sensitivity to lengthy launch delays. LEIA will monitor yeast growth in the radiation and reduced-gravity environment of the lunar surface no earlier than 2026, on a CLPS lander [4]. Changes include accommodating additional culture media and an additional LED color for a new biological assay (bioproduction of carotenoids-- dietary antioxidants), as well as modifications to the housing to allow late-load biology changeout and improved isolation between fluidics and electronics. Future prospects: Future work with the BioSensor, beyond LEIA, will include expanding the range and diversity of organisms and assays accommodated. Preliminary work has demonstrated the growth of Arabidopsis seedlings in BioSensor fluidic cards, including optical measurements of growth rate over time. Minor modifications could allow measurement of phenotypes related to photosynthetic capacity in both plants and cyanobacteria. The experimental capabilities of the BioSensor could be dramatically increased by introducing the capability for fluorescence measurements, and/or the design of novel biological assays using luminescence. The BioSensor can also be adapted for new platforms and experiment settings; in addition to free-flyer, ISS, and CLPS lander, a preliminary design concept has been developed for crewed deployment directly to the lunar surface. The instrument could be accommodated inside a lunar habitat, where its automated operation would make it an excellent candidate for experiments from fundamental investigations into the response of organisms to lunar surface conditions to applied-science purposes such as screening engineered strains of various organisms for bioproduction capability.

J A Lee↗
NASA NTRSDate not supplied

Machine Learning Application for Improving Cloud Detection and Phase Determination Over Sunglint Regions for Geostationary Satellites

Cloud detection and phase determination over sunglint regions has been a challenge, especially for geostationary (GEO) satellites. Sunglint is observed when the sunlight specular reflection is at the same viewing angle of the satellite sensor. This intense reflection in the visible channels (VIS) is often comparable to that from optically thick clouds. It also contaminates the shortwave infrared channels (SWIR). Consequently, VIS and SWIR channels become less useful - or not useful- when they are saturated, hampering the detection of cloudy and clear-sky pixels. Sunglint contamination happens frequently and exists nearly in every daytime GEO full disk satellite images. However, sunglint intensity and region are difficult to model due to variable viewing geometry and ocean surface conditions. Moreover, existing physical models do not meet the accuracy required for operational GEO satellite cloud detection. We developed a machine learning algorithm to improve cloud detection in sunglint conditions for the NASA Langley’s Satellite ClOud and radiation Property retrieval System (SatCORPS). This poster presents our recent progress in the algorithm development, validation and applications. The algorithm is validated using collocated SatCORPS GOES-East and GOES-West cloud products. We demonstrate that the machine learning cloud detection in sunglint regions is superior to the traditional approach by improving temporal consistency between sunglint and non-sunglint conditions.

Machine Learning, Cloud detection, Sunglint, SatCO↗
NASA NTRS2026

Hematite Is a Mineralogical Marker of Ancient Climate Change on Mars

The ancient climate of Mars changed from warm to cold surface conditions. This climate transition is demonstrated by geomorphological evidence, but lacks suitable mineralogical indicators. We investigate the crystallographic properties of hematite (iron oxide) in Gale crater, measured by the Curiosity rover, and compare them to laboratory experiments. Hematite crystallite sizes are ~5 to ~65 nm in the oldest sedimentary rocks investigated by the rover (the Murray formation) and <10 nm in the younger overlying strata (Mirador and Carolyn Shoemaker formations). We attribute the larger crystallites in the Murray formation to post-depositional coarsening by groundwater in warm and wet conditions, which persisted for several million years. Hematite with small crystallites co-occurs with goethite (iron oxyhydroxide) in the overlying layers, consistent with colder and water- limited conditions.

Marek Szczerba↗
NASA NTRS1973

Radiative property degradation of water impinging on thermally-controlled surfaces under space conditions.

Review of the results of an investigation aimed at determining experimentally the directional monochromatic reflectance changes caused under high-vacuum space conditions by a water spray impinging on thermally controlled surfaces consisting of three paint specimens (Z93, S13G, and 92-007) and an aluminum foil. The first two paints and the aluminum foil suffered considerable physical damage, but only small changes resulted in the reflectance of the paints while the reflectance of the aluminum foil decreased with increase in exposure time to the water jet. Only the 92-007 Dow Corning paint retained the same physical and reflective characteristics.

Maples, D.↗
NASA NTRS1993

The stability of oxyamphiboles: Existence of Ferric-bearing minerals under the reducing conditions on the surface of Venus

An enigma of Venusian mineralogy is the suggestion that Fe(3+)-bearing minerals exist under the reducing conditions of the Venusian atmosphere. Analysis of the spectrophotometric data from the Venera 13 and 14 missions, combined with the laboratory reflectance spectral measurements of oxidized basalts at elevated temperatures, led to the suggestion that metastable hematite might exist on Venus. Heating experiments at 475 C when f(sub O2) approximately 10(exp -24) demonstrated that the hematite to magnetite conversion is rapid indicating metastable hematite is not present on Venus. In addition to hematite, several other ferric oxide and silicate minerals have been proposed to occur on Venus, including laihunite or ferrifayalite, Fe(3+)-bearing tephroite, oxyamphiboles, and oxybiotites. Heating experiments performed on these Fe(3+)-bearing minerals under temperature-f(sub O2) conditions existing on Venus suggest that only oxyamphiboles and oxybiotites may be stable on the surface of Venus.

Straub, Darcy W.↗
NASA NTRS1991

Errors of five-day mean surface wind and temperature conditions due to inadequate sampling

Surface meteorological reports of wind components, wind speed, air temperature, and sea-surface temperature from buoys located in equatorial and midlatitude regions are used in a simulation of random sampling to determine errors of the calculated means due to inadequate sampling. Subsampling the data with several different sample sizes leads to estimates of the accuracy of the subsampled means. The number N of random observations needed to compute mean winds with chosen accuracies of 0.5 (N sub 0.5) and 1.0 (N sub 1,0) m/s and mean air and sea surface temperatures with chosen accuracies of 0.1 (N sub 0.1) and 0.2 (N sub 0.2) C were calculated for each 5-day and 30-day period in the buoy datasets. Mean values of N for the various accuracies and datasets are given. A second-order polynomial relation is established between N and the variability of the data record. This relationship demonstrates that for the same accuracy, N increases as the variability of the data record increases. The relationship is also independent of the data source. Volunteer-observing ship data do not satisfy the recommended minimum number of observations for obtaining 0.5 m/s and 0.2 C accuracy for most locations. The effect of having remotely sensed data is discussed.

Legler, David M.↗
NASA NTRS2012

Method for Pre-Conditioning a Measured Surface Height Map for Model Validation

This software allows one to up-sample or down-sample a measured surface map for model validation, not only without introducing any re-sampling errors, but also eliminating the existing measurement noise and measurement errors. Because the re-sampling of a surface map is accomplished based on the analytical expressions of Zernike-polynomials and a power spectral density model, such re-sampling does not introduce any aliasing and interpolation errors as is done by the conventional interpolation and FFT-based (fast-Fourier-transform-based) spatial-filtering method. Also, this new method automatically eliminates the measurement noise and other measurement errors such as artificial discontinuity. The developmental cycle of an optical system, such as a space telescope, includes, but is not limited to, the following two steps: (1) deriving requirements or specs on the optical quality of individual optics before they are fabricated through optical modeling and simulations, and (2) validating the optical model using the measured surface height maps after all optics are fabricated. There are a number of computational issues related to model validation, one of which is the "pre-conditioning" or pre-processing of the measured surface maps before using them in a model validation software tool. This software addresses the following issues: (1) up- or down-sampling a measured surface map to match it with the gridded data format of a model validation tool, and (2) eliminating the surface measurement noise or measurement errors such that the resulted surface height map is continuous or smoothly-varying. So far, the preferred method used for re-sampling a surface map is two-dimensional interpolation. The main problem of this method is that the same pixel can take different values when the method of interpolation is changed among the different methods such as the "nearest," "linear," "cubic," and "spline" fitting in Matlab. The conventional, FFT-based spatial filtering method used to eliminate the surface measurement noise or measurement errors can also suffer from aliasing effects. During re-sampling of a surface map, this software preserves the low spatial-frequency characteristic of a given surface map through the use of Zernike-polynomial fit coefficients, and maintains mid- and high-spatial-frequency characteristics of the given surface map by the use of a PSD model derived from the two-dimensional PSD data of the mid- and high-spatial-frequency components of the original surface map. Because this new method creates the new surface map in the desired sampling format from analytical expressions only, it does not encounter any aliasing effects and does not cause any discontinuity in the resultant surface map.

Sidick, Erkin↗
NASA NTRS2015

Lidar Observations of Atmospheric CO2 Column During 2014 Summer Flight Campaigns

Advanced knowledge in atmospheric CO2 is critical in reducing large uncertainties in predictions of the Earth' future climate. Thus, Active Sensing of CO2 Emissions over Nights, Days, and Seasons (ASCENDS) from space was recommended by the U.S. National Research Council to NASA. As part of the preparation for the ASCENDS mission, NASA Langley Research Center (LaRC) and Exelis, Inc. have been collaborating in development and demonstration of the Intensity-Modulated Continuous-Wave (IM-CW) lidar approach for measuring atmospheric CO2 column from space. Airborne laser absorption lidars such as the Multi-Functional Fiber Laser Lidar (MFLL) and ASCENDS CarbonHawk Experiment Simulator (ACES) operating in the 1.57 micron CO2 absorption band have been developed and tested to obtain precise atmospheric CO2 column measurements using integrated path differential absorption technique and to evaluate the potential of the space ASCENDS mission. This presentation reports the results of our lidar atmospheric CO2 column measurements from 2014 summer flight campaign. Analysis shows that for the 27 Aug OCO-2 under flight over northern California forest regions, significant variations of CO2 column approximately 2 ppm) in the lower troposphere have been observed, which may be a challenge for space measurements owing to complicated topographic condition, heterogeneity of surface reflection and difference in vegetation evapotranspiration. Compared to the observed 2011 summer CO2 drawdown (about 8 ppm) over mid-west, 2014 summer drawdown in the same region measured was much weak (approximately 3 ppm). The observed drawdown difference could be the results of the changes in both meteorological states and the phases of growing seasons. Individual lidar CO2 column measurements of 0.1-s integration were within 1-2 ppm of the CO2 estimates obtained from on-board in-situ sensors. For weak surface reflection conditions such as ocean surfaces, the 1- s integrated signal-to-noise ratio (SNR) of lidar measurements at 11 km altitude reached 376, which was equivalent to a 10-s CO2 error 0.33 ppm. For the entire processed 2014 summer flight campaign data, the mean differences between lidar remote sensed and in-situ estimated CO2 values were about -0.013 ppm. These results indicate that current laser absorption lidar approach could meet space measurement requirements for CO2 science goals.

Lin, Bing↗
NASA NTRS2013

Implicit Coupling Approach for Simulation of Charring Carbon Ablators

This study demonstrates that coupling of a material thermal response code and a flow solver with nonequilibrium gas/surface interaction for simulation of charring carbon ablators can be performed using an implicit approach. The material thermal response code used in this study is the three-dimensional version of Fully Implicit Ablation and Thermal response program, which predicts charring material thermal response and shape change on hypersonic space vehicles. The flow code solves the reacting Navier-Stokes equations using Data Parallel Line Relaxation method. Coupling between the material response and flow codes is performed by solving the surface mass balance in flow solver and the surface energy balance in material response code. Thus, the material surface recession is predicted in flow code, and the surface temperature and pyrolysis gas injection rate are computed in material response code. It is demonstrated that the time-lagged explicit approach is sufficient for simulations at low surface heating conditions, in which the surface ablation rate is not a strong function of the surface temperature. At elevated surface heating conditions, the implicit approach has to be taken, because the carbon ablation rate becomes a stiff function of the surface temperature, and thus the explicit approach appears to be inappropriate resulting in severe numerical oscillations of predicted surface temperature. Implicit coupling for simulation of arc-jet models is performed, and the predictions are compared with measured data. Implicit coupling for trajectory based simulation of Stardust fore-body heat shield is also conducted. The predicted stagnation point total recession is compared with that predicted using the chemical equilibrium surface assumption

Ablation↗
NASA NTRS2004

Enhanced Boiling on Micro-Configured Composite Surfaces Under Microgravity Conditions

Two experimental setups: High Heat Flux Pool Boiling Setup and Optical system of Measuring Contact Angle and Spreading Parameters were established and a series of experiments was conducted. The experimental work on the nucleate boiling performance of both Freon-113 and water on the composite surfaces has been finished and the results show that the composite surface with 25% volume fraction of graphite fibers in the copper matrix has the best enhancing performance. Stronger enhancement was obtained for water compared to Freon-113. The wall superheat initiating boiling was reduced 40% and 35% and the heat flux of the nucleate boiling was augmented up to ten times and 6.7 times, respectively. A bubble departure model has been presented to explain the enhancement mechanism of the boiling heat transfer on the composite surfaces. A powerful optical method to measure contact angle and spreading parameters of liquids on solid surfaces, including both transparent and non-transparent substrates, has been developed and successfully used in the measurements for various liquid-solid systems. The experimental work on identification of profiles near three-phase line by laser shadowgraphy method has been finished and the characteristics of the three-phase line for different liquid-solid systems were unveiled, which is very important to understand the mechanism of boiling under microgravity conditions. The four basic patterns of sessile profile were discovered through caustics and caustic-diffraction analysis by applying wave theory in shadowgraphy technology, which contributes to clearly explain the different characteristics of wetting and spreading of various liquids on a solid surface, and therefore to further understand the bubble departure mechanisms. A new working pattern of heat pipes using working fluids with positive surface-tension gradient against temperature was discovered and analyzed, and then the new heat pipe systems using this kind of working fluids have been presented. Two patent devices, i.e. Shadowgraphic Method to Measure Properties of Sessile Drops and Heat Pipe Systems Using New Working Fluids, have been developed; the former has been approved by The United States Patent & Trademark Office and the latter is being examined.

Source record↗
NASA NTRS1998

Experimental Studies of Hydrogenation and Other Reactions on Surfaces Under Astrophysically Relevant Conditions

The goal of our project is to study hydrogen recombination reactions on solid surfaces under conditions that are relevant in astrophysics. Laboratory experiments were conducted using low-flux, cold atomic H and D beams impinging on a sample kept under ultra high vacuum conditions. Realistic analogues of interstellar dust grains were used. Our results show that current models for hydrogen recombination reactions have to be modified to take into account the role of activated diffusion of H on surfaces even at low temperature.

Vidali, Gianfranco↗
NASA NTRSDate not supplied

ADVANCES IN PLUME-SURFACE INTERACTION SIMULATION CAPABILITY UNDER LUNAR LANDING CONDITIONS

The Fluid Dynamics Branch at theNASA Marshall Space Flight Center has assembled a portfolio of simulation tools to predict Plume-SurfaceInteraction (PSI) environments during extra-terrestrial propulsive landings. Particular focus is on engineering support for lunar landers such as robotic CommercialLunar Payload Services (CLPS) and the HumanLander System (HLS). Extension of existing PSI simulation capabilities are required to accurately capture the complex plume flow conditions and surface soil particle composition effects that arise in the lunar environment. The required model development and implementation, and extensive verification and validation of the key simulation tools, Loci/Chem [1]and Loci/Boltzmann [2], and Loci/GGFS [3] are now performed under a NASA Space Technology MissionDirectorate (STMD) funded multi-year GameChanging Development (GCD) project. The project will implement and mature these new modeling features and verify and validate them for the Mars andMoon environments with the aid of existing and new experiments to be performed under this project

Plume Surface Interaction↗