Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “source term”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

UAVs for Radiological Monitoring: Determining Ideal Operational Parameters From GEANT4 Simulations - 18025

Owing in no small part to the enormous advances in radiation detector technology (size, sensitivity and spectral-resolution), there has been an increased drive and requirement to accurately map both the spatial extent and magnitude of radiological contamination at the greatest possible spatial resolutions. To undertake this, a range of different methods have been devised and include the use of cars and human, but also planes (and more recently) unmanned aerial vehicles (UAVs). However, critical to the remote sensing using such UAVs in contrast to ground-based sensing, is (i) the selection of the ideal operational parameters to attain the best on-ground resolution in addition to, (ii) understanding the correct normalisation procedures and other influences on results that surveys at these reduced altitudes might present. Resulting from earlier works, through employing combined modelling and experimental data, the optimal height for a UAV survey using the more realistic 'area' radioactive source term (opposed to an infinitely-small 'point-source') is determined to be approximately 5 m - suitably maximizing cross detector counts. At greater altitudes than this, the influence of variations in neighboring topology / topography and nearby structures are observed to be negligible. However, at this and further-reduced altitudes (where optimal count-rates exists), small height-related variations are observed to result, and impact considerably on the complexity of the data normalisation. Whilst not occurring as a tool to entirely replace ground-based surveys, UAV systems are able to perform in challenging or dangerous environments, inadvisable or problematic to send humans. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

A Simultaneous Multi-phase Approach to Determine P-wave and S-wave Attenuation of the Crust and Upper Mantle

We have generalized the methodology of our regional amplitude tomography from the Lg phase to the four primary regional phases (Pn, Pg, Sn, Lg). Differences in the geometrical spreading, source term, site term, and travel paths are accounted for, while event source parameters such as seismic moment are consistent among phases. In the process, we have developed the first regional attenuation model that uses the amplitudes of four regional phases to determine a comprehensive P-wave and S-wave attenuation model of the crust and upper mantle. When applied to an area encompassing the Middle East, eastern Europe, western Asia, south Asia, and northeast Africa for the 1-2 Hz passband, we find large differences in the attenuation of the lithosphere across the region. The tectonic Tethys collision zone has high attenuation, while stable outlying regions have low attenuation. While crust and mantle Q variations are often consistent, we do find several notable areas where they differ considerably, but are appropriate given the region's tectonic history. Lastly, the relative values of Qp and Qs indicate that scattering Q is likely the dominant source of attenuation in the crust at these frequencies.

58 GEOSCIENCES↗

Analysis of the Reactor Physics of Low-Enrichment Fuel for the INL Advanced Test Reactor in support of RERTR

Analysis of the performance of the ATR with a LEU fuel design shows promise in terms of a core design that will yield the same neutron sources in target locations. A proposed integral cladding burnable absorber design appears to meet power profile requirements that will satisfy power distributions for safety limits. Performance of this fuel design is ongoing; the current work is the initial evaluation of the core performance of this fuel design with increasing burnup. Results show that LEU fuel may have a longer lifetime that HEU fuel however, such limits may be set by mechanical performance of the fuel rather that available reactivity. Changes seen in the radial fuel power distribution with burnup in LEU fuel will require further study to ascertain the impact on neutron fluxes in target locations. Source terms for discharged fuel have also been studied. By its very nature, LEU fuel produces much more plutonium than is present in HEU fuel at discharge. However, the effect of the plutonium inventory appears to have little affect on radiotoxicity or decay heat in the fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Construction of a Post-Irradiated Fuel Examination Shielded Enclosure Facility

The U.S. Department of Energy (DOE) has committed to provide funding to the Idaho National Laboratory (INL) for new post-irradiation examination (PIE) equipment in support of advanced fuels development. This equipment will allow researchers at the INL to accurately characterize the behavior of experimental test fuels after they are removed from an experimental reactor also located at the INL. The accurate and detailed characterization of the fuel from the reactor, when used in conjunction with computer modeling, will allow DOE to more quickly understand the behavior of the fuel and to guide further development activities consistent with the missions of the INL and DOE. Due to the highly radioactive nature of the specimen samples that will be prepared and analyzed by the PIE equipment, shielded enclosures are required. The shielded cells will be located in the existing Analytical Laboratory (AL) basement (Rooms B-50 and B-51) at the INL Material and Fuels Complex (MFC). AL Rooms B-50 and B-51 will be modified to establish an area where sample containment and shielding will be provided for the analysis of radioactive fuels and materials while providing adequate protection for personnel and the environment. The area is comprised of three separate shielded cells for PIE instrumentation. Each cell contains an atmosphere interface enclosure (AIE) for contamination containment. The shielding will provide a work area consistent with the as-low-as-reasonably-achievable (ALARA) concept, assuming a source term of 10 samples in each of the three shielded areas. Source strength is assumed to be a maximum of 3 Ci at 0.75 MeV gamma for each sample. Each instrument listed below will be installed in an individual shielded enclosure: Shielded electron probe micro-analyzer (EPMA) Focused ion beam instrument (FIB) Micro-scale x-ray diffractometer (MXRD). The project is designed and expected to be built incrementally as funds are allocated. The initial phase will be to fund the construction activities, which will include facility modifications and construction of one shielded enclosure. Follow-up activities will be to construct two additional shielded enclosures to complete the suite of three separate but connected remote operated examination areas. Equipment purchases are to be capital procurement spread out over several years on a funded schedule. This paper discusses safety and operational considerations given during the conceptual design phase of the project. The paper considers such things as project material at risk (MAR), new processes and equipment, potential hazards, and the major modification evaluation process to determine if a preliminary Documented Safety Analysis (PDSA) is required. As part of that process, an evaluation was made of the potential hazards with the new project compared to the existing and historical work and associated hazards in the affected facility.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Ginzburg-Landau model of Bose-Einstein condensation of magnons

We introduce a system of phenomenological equations for Bose-Einstein condensates of magnons in the one-dimensional setting. The nonlinearly coupled equations, written for amplitudes of the right- and left-traveling waves, combine basic features of the Gross-Pitaevskii and complex Ginzburg-Landau models. They include localized source terms to represent the microwave magnon-pumping field. With the source represented by the delta functions, we find analytical solutions for symmetric localized states of the magnon condensates. We also predict the existence of asymmetric states with unequal amplitudes of the two components. Numerical simulations demonstrate that all analytically found solutions are stable. With the delta-function terms replaced by broader sources, the simulations reveal a transition from the single-peak stationary symmetric states to multipeak ones, generated by the modulational instability of extended nonlinear-wave patterns. In the simulations, symmetric initial conditions always converge to symmetric stationary patterns. On the other hand, asymmetric inputs may generate nonstationary asymmetric localized solutions, in the form of traveling or standing waves. Comparison with experimental results demonstrates that the phenomenological equations provide for a reasonably good model for the description of the spatiotemporal dynamics of magnon condensates.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Parameter estimation and prediction for groundwater contamination based on measure theory

The problem of groundwater contamination in an aquifer is one with many uncertainties. Properly quantifying these uncertainties is es- sential in order to make reliable probabilistic based predictions and decisions regarding remediation strategies. In this work, a measure-theoretic frame- work is employed to quantify uncertainties in a simpli ed groundwater con- tamination transport model. Given uncertain data from observation wells, the stochastic inverse problem is solved numerically to obtain a probability measure on the space of unknown model parameters characterizing ground- water ow and contaminant transport in an aquifer, as well as unknown model boundary or source terms such as the contaminant source release into the environment. This probability measure is used to make predictions of future contaminant concentrations and to analyze possible remediation techniques. The ability to identify regions of small but nonzero probability using this method is illustrated.

54 ENVIRONMENTAL SCIENCES↗

Spatial assignment of symmetry adapted perturbation theory interaction energy components: The atomic SAPT partition

We develop a physically-motivated assignment of symmetry adapted perturbation theory for intermolecular interactions (SAPT) into atom-pairwise contributions (the A-SAPT partition). The basic precept of A-SAPT is that the many-body interaction energy components are computed normally under the formalism of SAPT, following which a spatially-localized two-body quasiparticle interaction is extracted from the many-body interaction terms. For electrostatics and induction source terms, the relevant quasiparticles are atoms, which are obtained in this work through the iterative stockholder analysis (ISA) procedure. For the exchange, induction response, and dispersion terms, the relevant quasiparticles are local occupied orbitals, which are obtained in this work through the Pipek-Mezey procedure. The local orbital atomic charges obtained from ISA additionally allow the terms involving local orbitals to be assigned in an atom-pairwise manner. Further summation over the atoms of one or the other monomer allows for a chemically intuitive visualization of the contribution of each atom and interaction component to the overall noncovalent interaction strength. Herein, we present the intuitive development and mathematical form for A-SAPT applied in the SAPT0 approximation (the A-SAPT0 partition). We also provide an efficient series of algorithms for the computation of the A-SAPT0 partition with essentially the same computational cost as the corresponding SAPT0 decomposition. We probe the sensitivity of the A-SAPT0 partition to the ISA grid and convergence parameter, orbital localization metric, and induction coupling treatment, and recommend a set of practical choices which closes the definition of the A-SAPT0 partition. We demonstrate the utility and computational tractability of the A-SAPT0 partition in the context of side-on cation-π interactions and the intercalation of DNA by proflavine. A-SAPT0 clearly shows the key processes in these complicated noncovalent interactions, in systems with up to 220 atoms and 2845 basis functions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effects of collisions on conservation laws in gyrokinetic field theory

Effects of collisions on conservation laws for toroidal plasmas are investigated based on the gyrokinetic field theory. Associating the collisional system with a corresponding collisionless system at a given time such that the two systems have the same distribution functions and electromagnetic fields instantaneously, it is shown how the collisionless conservation laws derived from Noether's theorem are modified by the collision term. Effects of the external source term added into the gyrokinetic equation can be formulated similarly with the collisional effects. Particle, energy, and toroidal momentum balance equations including collisional and turbulent transport fluxes are systematically derived using a novel gyrokinetic collision operator, by which the collisional change rates of energy and canonical toroidal angular momentum per unit volume in the gyrocenter space can be given in the conservative forms. The ensemble-averaged transport equations of particles, energy, and toroidal momentum given in the present work are shown to include classical, neoclassical, and turbulent transport fluxes which agree with those derived from conventional recursive formulations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Evaluation of PBR Spent Fuel Criticality and Dose Rate Compliance for Storage and Transportation

Spent tri-structural isotropic (TRISO)–based fuels have a strong track record in storage and transportation without documented incidents. This work seeks to reduce uncertainty to aid in more informed spent fuel management of TRISO-based fuels by modeling both fresh and spent pebble bed reactor (PBR) fuel and comparing the results to the regulatory standards from 10 CFR 71. SCALE was used for all modeling due to it having fast and accurate methods for handling PBR fuel modeling, as well as having an efficient method for shielding calculations in monaco with automated variance reduction using importance calculations (MAVRIC), which utilizes the consistent adjoint-driven importance sampling (CADIS) and the forward-weighted consistent adjoint-driven importance sampling (FW-CADIS) methods. KENO-VI was used for all criticality calculations, TSUNAMI was used for uncertainty quantification on k-effective, TRITON and the Oak Ridge isotope generation code (ORIGEN) were both used for depletion of the fuel, and MAVRIC was used for shielding calculations. For criticality assessments, this study focused on the requirement that the value of the neutron multiplication factor, k-effective (k-eff), would not exceed a peak value of 0.95, including uncertainty, with 95% confidence. Criticality was initially examined by modeling fresh fuel from three different designs—HTR-10 fuel, PBMR-400 fuel, and demonstration fuel representative of a TRISO-fueled modern high-temperature gas reactor (HTGR) design, henceforth referred to as Demo HTGR—and placing them into various sized containers with conditions described in 10 CFR 71 to quantify the peak k-eff state. When the peak value of 0.95 k-eff was exceeded, mitigation methods were examined in those scenarios. Burnup credit, pebble displacement in areas of strong neutron multiplication, and random pebble replacement using pebbles of various compositions and replacement fractions were examined. In summary, the criticality of PBR fuels can be well accounted for by restricting container size, taking credit for burnup, or by displacing/replacing pebbles. Uncertainty of the k-eff due to nuclear data uncertainties was recorded at ~0.6644%Δk/k, or roughly 664% mil (pcm). The nuclear data–induced uncertainty was relatively small and should not require significant modification in the design to be accounted for. Revisions to the evaluated nuclear data file values have been shown to have a larger impact than nuclear data–induced uncertainty. For dose rate aspects, U.S. Nuclear Regulatory Commission regulations require a maximum dose rate of 10 millirem per hour (mrem/h) at 2 meters. In examining the dose rate behavior of spent PBR fuel, the representative Demo HTGR fuel was modeled exclusively due to it possessing the highest target burnup of the examined fuels. Equilibrium cycle modeling methods were used to produce a higher-fidelity discharge isotopic composition than simple assumptions, such as reflected pebbles. The discharge composition was used as a source term in the fixed-source transport shielding calculations, and dose rates were calculated at 2 m for the shortest possible cooling time. The low concentration of fuel material led to dose rates that were in line with regulatory limits, despite the high burnup when compared to traditional light water reactor fuels. In conclusion, the methods employed in this study would require more work to further verify and validate and are limited to the criticality and dose rate analyses performed.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Integrated Approach to Fluoride High Temperature Reactor Technology and Licensing Challenges (FHR-IRP)

This document constitutes progress made on this project by the Georgia Tech led Integrated Approach to Fluoride High Temperature Reactor Technology and Licensing Challenges (FHR-IRP). This is the first draft of the project final report. Chapter 3 is focused on Tritium management. Tritium management in Fluoride-salt High-temperature Reactors (FHRs) presents a major operational concern and a significant challenge. Tritium is generated via multiple pathways including various interactions in fuel and structural materials, as well as coolant (primarily interaction with lithium and beryllium), leading to a complex evolution and spatial distribution of tritium generation rate. FHR generates orders of magnitude more tritium than in LWRs, and has potential for a significant release, via permeation through structural materials (due to high temperature), and through heat exchanger(s). Therefore, accurate estimate is necessary. For that purpose relevant tritium production pathways were identified. A methodology to obtain space-time dependent tritium generation rate was developed and implemented, employing SCALE and MCNP codes. Detailed models of the reference Advanced High Temperature Reactor (AHTR) design were developed. A multi-parametric metrics was introduced to capture relevant tritium production indicators, including the instantaneous tritium production rate, total tritium production (neglecting subsequent decay), and accumulated tritium production (accounting for the decay). The obtained results will inform tritium management, including the sizing of the components, and to gain insight on the impact of the core design parameters on tritium generation rates. Research effort on Liquid Salt Impurity Removal, Redox and Corrosion Control is discussed in Chapter 4. Section 4.1 is an introduction chapter. Based on the current available knowledge and operation experience on previous MSRs and other types of nuclear reactors, the report identifies the major impurities that are related to either material compatibility, salt properties or radioactive source terms, and the potential contamination sources of these impurities, their transport in the primary coolant loop and available cleanup methodologies for a particular group of impurity. In section 4.2, the available purification methods were discussed, including the liquid/liquid extraction using liquid Bi-Li which has been applied in MSBR and electrochemical purification which is developed based on Pyroprocessing. In this section, the new multi-stage and multi-salt-component was developed and discussed. Section 4.3 discussed the redox potential control for salt chemistry and corrosion mitigation, including the control theory and the soluble/soluble buffer control method. The section also developed method on how to analyze soluble/soluble redox reaction in a molten salt system and designed an electrochemical sensor for redox potential control. Corrosion models were also reported in this section. Section 4.4 focused on how to measure the fundamental properties in a molten salt. As an example, the section focused on La fluoride in the molten salt. The section developed methods on how analyze electrochemical measurement data to obtain the fundamental properties including the redox potential, diffusion coefficient and exchange current density. All these fundamental information is important for salt purification system development. Section 4.5 focused on measurements of corrosion products in the salts. Because of the different behaviors between Cr and La in the salt, new analysis method for Cr fluorides in the salt was developed. Some results for Fe fluoride in the salt and corrosion measurements were also reported. Section 4.6 demonstrated the separation of oxide from the salt. This section also measured the solubility of La 2 O 3 in the salt as function of temperature. Section 4.7 focused on the separation of La and Ce from the molten salt. These two elements were selected because La was found to be separated by using inert electrode, while for separation of Ce, reactive electrode must be selected. Section 4.8 demonstrated the separation iodine ions from the molten salt. Two kinds of working electrode materials (metal W and graphite) were investigated. Section 4.9 focused on the fundamental data of fission products and actinides in liquid Bi. The chapter reviewed the available data, then based a CALPHAD model, the available data were broadened to the concentration-dependent cases.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

A new aerodynamic integral equation based on an acoustic formula in the time domain

An aerodynamic integral equation for bodies moving at transonic and supersonic speeds is presented. Based on a time-dependent acoustic formula for calculating the noise emanating from the outer portion of a propeller blade travelling at high speed (the Ffowcs Williams-Hawking formulation), the loading terms and a conventional thickness source terms are retained. Two surface and three line integrals are employed to solve an equation for the loading noise. The near-field term is regularized using the collapsing sphere approach to obtain semiconvergence on the blade surface. A singular integral equation is thereby derived for the unknown surface pressure, and is amenable to numerical solutions using Galerkin or collocation methods. The technique is useful for studying the nonuniform inflow to the propeller.

Farassat, F.↗

A parallel iterative solution method for systems of nonlinear hyperbolic equations

An iterative algorithm suitable for the solution of a system of nonlinear hyperbolic partial differentiation equations in multiple dimensions is discussed. Current numerical methods for systems of nonlinear PDEs have limited parallelism due to strong coupling between the equations. This method decouples the PDEs by linearizing the convention coefficient for a space-time domain. This provides large grain parallelism. The linearization also allows the treatment of some terms in the equations as source terms, providing more freedom to choose from a wider variety of numerical methods. Smaller grain parallelism may be exploited within the solves for each equation. Thus, the method has potential for parallelism at several levels.

Scroggs, Jeffrey S.↗

Some implementational issues of convection schemes for finite volume formulations

Two higher-order upwind schemes - second-order upwind and QUICK - are examined in terms of their interpretation, implementation as well as performance for a recirculating flow in a lid-driven cavity, in the context of a control volume formulation using the SIMPLE algorithm. The present formulation of these schemes is based on a unified framework wherein the first-order upwind scheme is chosen as the basis, with the remaining terms being assigned to the source term. The performance of these schemes is contrasted with the first-order upwind and second-order central difference schemes. Also addressed in this study is the issue of boundary treatment associated with these higher-order upwind schemes. Two different boundary treatments - one that uses a two-point scheme consistently within a given control volume at the boundary, and the other that maintains consistency of flux across the interior face between the adjacent control volumes - are formulated and evaluated.

Thakur, Siddharth↗

Some implementational issues of convection schemes for finite-volume formulations

Two higher-order upwind schemes - second-order upwind and QUICK - are examined in terms of their interpretation, implementations, as well as performance for a recirculating flow in a lid-driven cavity, in the context of a control-volume formulation using the SIMPLE algorithm. The present formulation of these schemes is based on a unified framework wherein the first-order upwind scheme is chosen as the basis, with the remaining terms being assigned to the source term. The performance of these schemes is contrasted with the first-order upwind and second-order central difference schemes. Also addressed in this study is the issue of boundary treatment associated with these higher-order upwind schemes. Two different boundary treatments - one that uses a two-point scheme consistently within a given control volume at the boundary, and the other that maintains consistency of flux across the interior face between the adjacent control volumes - are formulated and evaluated.

Thakur, Siddharth↗

Modeling of x-ray fluorescence using MCNPX and Geant4

X-Ray Fluorescence (XRF) is one of thirteen non-destructive assay techniques being researched for the purpose of quantifying the Pu mass in used fuel assemblies. The modeling portion of this research will be conducted with the MCNPX transport code. The research presented here was undertaken to test the capability of MCNPX so that it can be used to benchmark measurements made at the ORNL and to give confidence in the application of MCNPX as a predictive tool of the expected capability of XRF in the context of used fuel assemblies. The main focus of this paper is a code-to-code comparison between MCNPX and Geant4 code. Since XRF in used fuel is driven by photon emission and beta decay of fission fragments, both terms were independently researched. Simple cases and used fuel cases were modeled for both source terms. In order to prepare for benchmarking to experiments, it was necessary to determine the relative significance of the various fission fragments for producing X-rays.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Development of ARCHER towards clinical use: modeling and simulation of Varian Linac for radiation therapy dose calculations - 25449

Monte Carlo particle transport methods are well recognized as the most accurate approach to dose calculations for radiation therapy treatment planning. However, the lengthy calculation time has prevented Monte Carlo methods from being applied to dose calculations in the planning of radiation therapy. Recently, the emerging parallel computing hardware accelerators, such as general-purpose Graphics Processing Unit (GPU), have significantly boosted the performance of Monte Carlo codes. The accuracy of a clinical dose engine depends greatly on the accuracy of source term modeling and the methodology of dose calculations. Hence, in this study, an efficient and accurate source model of the Varian TrueBeam{sup R} Linac is developed and integrated with a fast photon-electron transport module of the recently developed high-performance Monte Carlo code, ARCHER. The validity of the source model and the particle transport physics are verified with established dose calculation codes such as EGSnrc and validated with experimental measurements. To demonstrate the capability of the platform in clinical applications, three clinical treatment plans (the lung, breast, and prostate) are simulated and analyzed. From the perspective of performance, the entire simulation of each clinical plan, starting from the source modeling to the end of particle transport within the patient phantom, can be finished in less than one minute using a single Titan X GPU card with 1% statistical error. In comparison, the same cases take the EGSnrc code hundreds of CPU hours to finish. The results suggest that this new version of ARCHER code has been successfully developed and tested as a clinically deployable dose engine for external photon beam IMRT plans in the clinical setting. (authors)

61 RADIATION PROTECTION AND DOSIMETRY↗

A Maxwell formulation for the equations of a plasma

In light of the analogy between the structure of electrodynamics and fluid dynamics, the fluid equations of motion may be reformulated as a set of Maxwell equations. This analogy has been explored in the literature for incompressible turbulent flow and compressible flow but has not been widely explored in relation to plasmas. This letter introduces the analogous fluid Maxwell equations and formulates a set of Maxwell equations for a plasma in terms of the species canonical vorticity and its cross product with the species velocity. The form of the source terms is presented and the magnetohydrodynamic (MHD) limit restores the typical variety of MHD waves.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Broadband Lg Attenuation Modeling in the Middle East

We present a broadband tomographic model of Lg attenuation in the Middle East derived from source- and site-corrected amplitudes. Absolute amplitude measurements are made on hand-selected and carefully windowed seismograms for tens of stations and thousands of crustal earthquakes resulting in excellent coverage of the region. A conjugate gradient method is used to tomographically invert the amplitude dataset of over 8000 paths over a 45{sup o} x 40{sup o} region of the Middle East. We solve for Q variation, as well as site and source terms, for a wide range of frequencies ranging from 0.5-10 Hz. We have modified the standard attenuation tomography technique to more explicitly define the earthquake source expression in terms of the seismic moment. This facilitates the use of the model to predict the expected amplitudes of new events, an important consideration for earthquake hazard or explosion monitoring applications. The attenuation results have a strong correlation to tectonics. Shields have low attenuation, while tectonic regions have high attenuation, with the highest attenuation at 1 Hz is found in eastern Turkey. The results also compare favorably to other studies in the region made using Lg propagation efficiency, Lg/Pg amplitude ratios and two-station methods. We tomographically invert the amplitude measurements for each frequency independently. In doing so, it appears the frequency-dependence of attenuation is not compatible with the power law representation of Q(f), an assumption that is often made.

58 GEOSCIENCES↗