Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “sintering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Dislocation density in fine grain-size spark-plasma sintered aluminum measured using high brightness synchrotron radiation

In this study, three-dimensional orientation mapping of samples of aluminum prepared by spark plasma sintering (SPS) with average grain sizes of 5 μm and 1 μm has been carried out using high-brightness synchrotron radiation, from which the geometrically necessary dislocation (GND) density has been determined. The low average measured GND density values confirm that the SPS process can be used to produce samples containing grains with dislocation density similar to that of fully recrystallized coarse-grained samples. Values of GND density are also compared to those obtained from electron back-scatter diffraction studies on the same material, highlighting the significantly higher angular resolution of the synchrotron data. For the 5 μm grain-size sample the measured GND density can account for a large fraction of the previously observed positive Hall-Petch deviation of this material. For the 1 μm grain-size sample, however, the GND-based strengthening contribution is much smaller than the reported positive Hall-Petch deviation, such that the additional strength may be reliably associated with dislocation source-limited strengthening.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Solid-state reaction mediated microstructural evolution in a spark plasma sintered in situ Ti–B 4 C composite

For this study, a novel porosity-free in situ Ti–B 4 C composite was fabricated via spark plasma sintering (SPS). Detailed analysis of the phase evolution, coupling results from XRM, XRD and SEM-EBSD-EDS, indicate that primarily TiB 2 precipitates formed due to the in-situ reactions between the boron-carbide and titanium powders. The precipitation of TiB 2 resulted in the formation of a graphitic C-rich thin layer circumscribing the partially reacted B 4 C particles. Further progression of the in-situ reaction leads to the out-diffusion of the excess carbon from the B 4 C particles, across the graphite and TiB 2 phases, forming TiC upon reacting with the titanium matrix. Therefore, the final microstructure primarily consisted of TiB 2 , TiC, and partially reacted B 4 C phases, with small amounts of TiB, α-Ti, and graphite. Furthermore, the microstructure in these SPS processed in situ composites appeared to be the product of a solid-state Ti–B 4 C diffusion couple, substantially different from their fusion-based additively manufactured counterparts. Nano-indentation tests revealed a remarkably high average hardness of ~25 GPa for this SPS-processed Ti–B 4 C composite and comparable (with literature) phase-specific hardness and modulus values for the constituent TiB 2 , TiC, and B 4 C phases.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Electric-field-assisted-sintering of rare-earth oxide dispersion strengthened Fe-Cr-Mo alloys

Oxide dispersion-strengthened (ODS) alloys are widely recognized for their exceptional high-temperature strength, creep resistance, and radiation tolerance, making them indispensable for advanced nuclear reactors, aerospace, and energy systems. Achieving a fine and stable dispersion of oxide nanoparticles is critical, as these particles act as strong barriers to dislocation motion and effective sinks for irradiation-induced defects, ensuring structural integrity under extreme conditions. Here, in this study, Fe–Cr–Mo-based ODS alloys were fabricated via mechanical alloying and consolidated using electric-field-assisted sintering (EFAS) with additions of Y 2 O 3 , La 2 O 3 , and CeO 2 . EFAS processing produced ultrafine-grained microstructures (average grain size <1 μm) with uniformly distributed oxide clusters (2–4 nm). Atom probe tomography revealed that La 2 O 3 -containing alloys exhibited the highest nanoparticle number density, resulting in superior tensile strength compared to yttria- and ceria-bearing counterparts. The combined effect of grain refinement and rare-earth oxide dispersion significantly enhanced mechanical performance, demonstrating the potential of EFAS for developing high-strength ferritic alloys for demanding environments such as nuclear systems.

36 - MATERIALS SCIENCE↗
DOE OSTI2025

Amorphous complexion-aided sintering enables scalable processing of bulk nanocrystalline Cu-Zr with high strength and compressive plasticity

Nanocrystalline alloys can have exceptional strengths, yet due to limited microstructural stability it is difficult to fabricate bulk pieces through traditional processing routes that retain nanosized grains. In this study, centimeter-sized Cu-Zr alloy pellets were fabricated via a simple and improved powder metallurgy processing route. Different consolidation temperatures and times were employed to investigate the effect of amorphous grain boundary complexions on densification and the resulting mechanical properties. Bulk compression tests were carried out, with the samples that were hot pressed at 900 °C for 10 h exhibiting an excellent combination of average yield strength of 722 ± 45 MPa and average failure strain of 25.3 ± 2.4 %. Furthermore, we find that a powder processing route which enables amorphous complexion-assisted sintering leads to samples that (1) reach full density without requiring quenching treatments or other complex processing, (2) demonstrate appreciable plasticity, and (3) have strength that competes with commercially available high-strength Cu alloys.

Bulk nanocrystalline alloy↗
DOE OSTI2019

Radiative Properties of Coal Ash Deposits with Sintering Effects

The heat-transfer characteristics in the fireside of a pulverized-coal furnace are affected, among other factors, by the physical and chemical characteristics of the ash deposits. Indeed, the physical state of the ash deposits and their chemical composition determine the radiative and conductive properties of the furnace walls. Particularly, several complex mechanisms are involved in the radiative heat-transfer process at the walls that restricts the absorption of the incident radiation of the flame, particles, and hot gases. These mechanisms involve dependencies on the radiation spectrum due to the ash chemical composition and ash-sintering effects that enhance or hinder the overall heat transfer. In this work, the complex mechanisms that describe the heat exchange in the presence of ash deposits and their impact on the prediction of the wall emissivity and ultimately the wall heat transfer in a real system are discussed.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2024

Pelletization with Spark Plasma Sintering and Characterization of Metal Iodides: An Assessment of Long-Term Radioiodine Immobilization Options

Four promising iodine “getter” materials (Ag, Cu, Bi, and Sn) for radioiodine capture were assessed in their pure metal-iodide (MI x ) pelletized forms to compare relative chemical durabilities. To study chemical durability, commercial MI x compounds of AgI, BiI 3 , BiOI, CuI, and SnI 4 were converted to dense monolithic pellets using spark plasma sintering. Semidynamic leach testing in the form of modified ASTM C1308 tests was then performed on the pellets in two different forms including unmounted (as-pressed) specimens (i.e., “U”) and epoxy-mounted specimens (i.e., “M”) with polished surfaces. The chemical durability results and sample characterizations showed that three of the five MI x compounds tested (i.e., AgI, CuI, and BiOI) displayed moderate to high leach resistances. Further, the remaining two MI x compounds (i.e., BiI 3 and SnI 4 ), which are both desirable iodine waste forms due to their high iodine loading capacities, readily decomposed during leach testing, indicated by crystallographic changes in the specimens as well as large amounts of iodine detected in the leachate solutions. The instabilities of BiI 3 and SnI 4 raise uncertainties for using the base metals/cations (i.e., Bi 0 /Bi 3+ and Sn 0 /Sn 4+ , respectively) as viable getters for radioiodine capture due to likely poor waste form chemical durabilities after capture and consolidation into waste forms.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2017

Toward the Design of a Hierarchical Perovskite Support: Ultra-Sintering-Resistant Gold Nanocatalysts for CO Oxidation

We report that an ultrastable Au nanocatalyst based on a heterostructured perovskite support with high surface area and uniform LaFeO 3 nanocoatings was successfully synthesized and tested for CO oxidation. Strikingly, small Au nanoparticles (4–6 nm) are obtained after calcination in air at 700 °C and under reaction conditions. The designed Au catalyst not only possessed extreme sintering resistance but also showed high catalytic activity and stability because of the strong interfacial interaction between Au and the heterostructured perovskite support.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Study on different characteristics of doped tri calcium phosphate at different sintering temperatures

Pure β-tricalcium phosphate (β-TCP), Zn-doped (3wt %) β-TCP and Mg- doped (3wt %) β-TCP samples were prepared by using a wet chemical precipitation synthesis technique, followed by calcination at 800 °C in air. The developed materials were subjected to sintering at different temperatures. Density and porosity were compared. The X-ray diffractometry (XRD) and Fourier-transformed infrared (FTIR) spectrometer were used to examine the changes in crystalline phases and presence of functional groups of TCP ceramics. The scanning electron microscopy (SEM) was used to study the pore formation, pore size, grain size.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Effect of process parameters on hardness, temperature profile and solidification of different layers processed by direct metal laser sintering (DMLS)

In DMLS process objects are fabricated layer by layer from powdered material by melting induced by a controlled laser beam. Metallic powder melts and solidifies to form a single layer. Solidification map during layer formation is an important route to characterize micro-structure and grain morphology of sintered layer. Generally, solidification leads to columnar, equiaxed or mixture of these two types grain morphology depending on solidification rate and thermal gradient. Eutectic or dendritic structure can be formed in fully equiaxed zone. This dendritic growth has a large effect on material properties. Smaller dendrites generally increase ductility of the layer. Thus, materials can be designed by creating desired grain morphology in certain regions using DMLS process. To accomplish this, hardness, temperature distribution, thermal gradient and solidification cooling rate in processed layers will be studied under change of process variables by using finite element analysis, with specific application to Ti-6Al-4V.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Effect of different grain boundary diffusion alloys on magnetic properties of Dy-free sintered NdFeB magnet

Dy-free sintered magnets were fabricated by blending Neo powder with different grain boundary diffusion alloy powders. Cu, CeAl and CeAlCu have a negative effect on H cj of magnets, while PrAlCu and AlCuGa have a positive effect. The PrAlCu-added magnet achieves the best magnetic properties among all magnets with the additions of different diffusion alloys. With increasing PrAlCu from 0-10 wt.%, H cj of the magnets gradually increases from the original 14.5 kOe to 19.2 kOe. The magnet with 7.5 wt.% PrAlCu obtains a H cj of 18 kOe and (BH) max of 39.1 MGOe. It is found that Pr and Cu in PrAlCu alloy is mainly distributed at grain boundary and triple junctions, leading to a reduced coupling among grains, thus an enhanced H cj . Here, the grain boundary engineering by adding an appropriate alloy is an effective method to improve H cj of Dy-free NdFeB magnets.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Spark plasma sintering of structure-tailored ultrahigh-temperature components: First step to complex net shaping

The net-shaping capability in spark plasma sintering (SPS) of ultrahigh-temperature ceramics has been explored in this study. The annular or ring-like shape is considered here as the first step to a more complex geometry compared to a solid cylinder or disk. ZrC powders have been SPS processed in specially designed graphite tooling to achieve the annular shape geometry. Experimental runs have been carried out to determine the optimal processing parameters for producing highly dense ZrC specimens in this geometry. Finite-element modeling framework has been constructed to determine the internal stress evolution, as well as densification, during the SPS of the annular-shaped ZrC. The formulated processing schemes for ZrC have been adapted to process SiC/ZrB2 composite powder with the purpose of making tooling components for SPS applications. The applicability of the obtained composite SPS tooling has been evaluated at high temperature and high pressure associated with SPS regimes.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Energy efficient spark plasma sintering: Breaking the threshold of large dimension tooling energy consumption

An energy efficient spark plasma sintering method enabling the densification of large size samples assisted by very low electric current levels is developed. In this method, the electric current is concentrated in the graphite foils around the sample. High-energy dissipation is then achieved in this area enabling the heating and full densification of large (alumina) parts (Ø 40 mm) at relatively low currents (800 A). The electrothermal mechanical simulation reveals that the electric current needed to heat the large samples is 70% lower in the energy efficient configuration compared to the traditional configuration. The presence of thermal and densification gradients is also revealed for the larger size samples. Potential solutions for this problem are discussed. The experiments confirm the possibility of full densification (96%-99%) of large alumina samples. This approach allows using small (and low cost) SPS devices (generally limited to 10-15 mm samples) for large-size samples (40-50 mm). Finally, the developed technique enables also an optimized energy consumption by large-scale SPS systems.

36 MATERIALS SCIENCE↗
DOE OSTI2020

In situ characterization of ceramic cold sintering by small-angle scattering

The first in situ characterization of the pore morphology evolution during the cold sintering process (CSP) is presented using small-angle X-ray scattering methods. For practical reasons, measurements have been made on a model system, KH 2 PO 4 (KDP). The scattering signal revealed a striking behavior that could be modeled with nanoscale structural features associated with the dissolution and reprecipitation of KDP close to the grain/pore interface during CSP. The prospects for future more quantitative experiments under a range of temperature and pressure conditions, as well as for studies of more technologically important materials such as ZnO are considered.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effect of V Content on Corrosion Behavior of Al-V Alloys Produced by Mechanical Alloying and Subsequent Spark Plasma Sintering

Al-V alloys produced via high-energy ball milling have been reported to show simultaneous improvement of corrosion resistance and mechanical properties compared to traditional Al alloys. In these alloys, V content plays a crucial role in increasing or decreasing the corrosion resistance. Therefore, the effect of V and microstructure on corrosion of high-energy ball milled and subsequently spark plasma sintered Al-xV alloys (x = 2, 5, 10 at%) has been studied. Cyclic potentiodynamic polarization tests and electrochemical impedance spectroscopic analysis revealed the increment of V content up to 5 at% enhanced the corrosion resistance of the alloy. However, highly heterogeneous microstructure in Al-10 at%V resulted in significant localized corrosion over the immersion time. The electrochemical impedance spectroscopy studies over 14 days of immersion revealed underlying corrosion mechanisms.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Synthesis and behavior of bulk iron nitride soft magnets via high-pressure spark plasma sintering

Abstract In this study, dense bulk iron nitrides (Fe x N) were synthesized for the first time ever using spark plasma sintering (SPS) of Fe x N powders. The Fe 4 N phase of iron nitride in particular has significant potential to serve as a new soft magnetic material in both transformer and inductor cores and electrical machines. The density of SPSed Fe x N increased with SPS temperature and pressure. The microstructure of the consolidated bulk Fe x N was characterized with X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and superconducting quantum interference device (SQUID) magnetometry. XRD revealed a primary phase of Fe 4 N with secondary phases of Fe 3 N and metallic iron. Finite element analysis (FEA) was also applied to investigate and explain localized heating and temperature distribution during SPS. The effects of processing on interface bonding formation and phase evolution were investigated and discussed in detail to provide insight into fundamental phenomena and microstructural evolution in SPSed Fe x N. Graphic abstract

36 MATERIALS SCIENCE↗
DOE OSTI2024

Development of Novel Sintered Carbon-Ore Building Materials

The main objective for this project was to develop value-added products from carbon-ore leading to commercialization of a carbon-based product. These carbon-based products (LIG2 products) are produced using the sintered carbon-ore building materials (SCBM) technology and have carbon contents greater than 70 wt.% carbon with greater than 51wt.% of the carbon coming from carbon-ore. The project team produced LIG2 bricks at a rate of five bricks per day and characterized the material properties of the bricks. These products can then be used in fabrication of a carbon-based building. A technical and economic analysis (TEA), cradle-to-grave life cycle analysis (LCA), technology gap analysis, and conceptual design were also completed for the LIG2 carbon-ore brick manufacturing process.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2026

Enhancing CMC Temperature Performance in High Hydrogen Environments using Field Assisted Sintering Technology

This final report summarizes the developments in field assisted sintering technology (FAST) for rapid fabrication of ceramic matrix composite (CMC) materials with integrated environmental barrier coatings (EBCs), as well as their performance in a representative gas turbine combustor environment including stagnant flame zones, and high velocity product zones. CMCs are a possible high temperature tolerant material system for gas turbine engines, which are currently the dominant source of electric power production and the primary source of aircraft propulsion. However, CMCs are costly and time-consuming (on the order of weeks to months) to fabricate, and CMCs based on silicon carbide (SiC) ceramics are susceptible to water vapor degradation requiring the use of specialized EBCs. The manufacturing technique known as FAST can create consolidated parts in as little as a few hours using high pressure and temperature, and may be useful to integrate EBCs into CMCs directly during consolidation.

08 HYDROGEN↗
DOE OSTI2018

Fabrication of Titanium-Niobium-Zirconium-Tantalium Alloy (TNZT) Bioimplant Components with Controllable Porosity by Spark Plasma Sintering

Spark Plasma Sintering (SPS) is used to fabricate Titanium-Niobium-Zirconium-Tantalum alloy (TNZT) powder—based bioimplant components with controllable porosity. The developed densification maps show the effects of final SPS temperature, pressure, holding time, and initial particle size on final sample relative density. Correlations between the final sample density and mechanical properties of the fabricated TNZT components are also investigated and microstructural analysis of the processed material is conducted. A densification model is proposed and used to calculate the TNZT alloy creep activation energy. The obtained experimental data can be utilized for the optimized fabrication of TNZT components with specific microstructural and mechanical properties suitable for biomedical applications.

36 MATERIALS SCIENCE↗