Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “sensor data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

Low power, compact charge coupled device signal processing system

A variety of charged coupled devices (CCDs) for performing programmable correlation for preprocessing environmental sensor data preparatory to its transmission to the ground were developed. A total of two separate ICs were developed and a third was evaluated. The first IC was a CCD chirp z transform IC capable of performing a 32 point DFT at frequencies to 1 MHz. All on chip circuitry operated as designed with the exception of the limited dynamic range caused by a fixed pattern noise due to interactions between the digital and analog circuits. The second IC developed was a 64 stage CCD analog/analog correlator for performing time domain correlation. Multiplier errors were found to be less than 1 percent at designed signal levels and less than 0.3 percent at the measured smaller levels. A prototype IC for performing time domain correlation was also evaluated.

Bosshart, P. W.↗

Turbid water measurements of remote sensing penetration depth at visible and near-infrared wavelength

Remote sensing of water quality is dicussed. Remote sensing penetration depth is a function both of water type and wavelength. Results of three tests to help demonstrate the magnitude of this dependence are presented. The water depth to which the remote-sensor data was valid was always less than that of the Secchi disk depth, although not always the same fraction of that depth. The penetration depths were wavelength dependent and showed the greatest variation for the water type with largest Secchi depth. The presence of a reflective plate, simulating a reflective subsurface, increased the apparent depth of light penetration from that calculated for water of infinite depth.

Morris, W. D.↗

An investigation of surface albedo variations during the recent Sahel drought

Applications Technology Satellite (ATS) 3 green sensor data are used to measure surface reflectance variations in the Sahara/Sahel during the recent drought period 1967-74. The magnitude of the seasonal reflectance change is shown to be as much as 80% for years of normal precipitation and less than 50% for drought years. Year-to-year comparisons during both wet and dry seasons reveal the existence of a surface reflectance cycle coincident with the drought intensity. The relationship between the green reflectance and solar albedo is examined and estimated to be about 0.6 times the reflectance change observed by the green channel.

Norton, C. C.↗

Guidance of an autonomous planetary rover based on a short-range hazard detection system

The guidance of an autonomous planetary roving vehicle using a scanning laser/multidetector terrain sensor for short-range hazard detection has been simulated. The sensor data are used to model the terrain, thereby providing the information required by a path selection algorithm to control the motion of the rover. These simulation studies are providing the basis for developing both the real-time computer control software and the hardware systems for laboratory and field testing of rover.

Yerazunis, S. W.↗

SEASAT-A synthetic aperture radar performance

The SEASAT-A satellite synthetic aperture radar (SAR) is presented, and its performance since it began operation in July 1978, is examined. The imaging radar system, the first to be designed as an orbital scientific instrument, was intended to generate continuous imagery over a 100-km swath at 25-m resolution from an altitude of 800 km. SAR image quality is measured in terms of resolution, the range of detectable radar backscatter, and the contrast ratio, each of which is affected by antenna, sensor, data link, and recording/processor subsystem parameters. Microdensitometer scans of output image film of actual SEASAT-A SAR data reveal a range resolution of less than 25 m, an azimuth resolution of approximately 40 m, a noise equivalent dynamic range of from 9.6 to -21 + or - 5 dB, and an image contrast ratio of 7.5 dB. SEASAT-A SAR performance is concluded to have confirmed the utility of spaceborne radar sensing.

Jordan, R. L.↗

Training site statistics from Landsat and Seasat satellite imagery registered to a common map base

Landsat and Seasat satellite imagery and training site boundary coordinates were registered to a common Universal Transverse Mercator map base in the Newport Beach area of Orange County, California. The purpose was to establish a spatially-registered, multi-sensor data base which would test the use of Seasat synthetic aperture radar imagery to improve spectral separability of channels used for land use classification of an urban area. Digital image processing techniques originally developed for the digital mosaics of the California Desert and the State of Arizona were adapted to spatially register multispectral and radar data. Techniques included control point selection from imagery and USGS topographic quadrangle maps, control point cataloguing with the Image Based Information System, and spatial and spectral rectifications of the imagery. The radar imagery was pre-processed to reduce its tendency toward uniform data distributions, so that training site statistics for selected Landsat and pre-processed Seasat imagery indicated good spectral separation between channels.

Clark, J.↗

On-line structural parameter identification

Algorithms are presented for on-line parameter identification of structural dynamic systems. As an example, they are used to calculate the parameters of a modal model of a flexible beam. The algorithms are tested using hardware consisting of a 12 ft. beam with four voice coil actuators and nine noncontacting displacement sensors. They are programmed in a CDC Cyber 175 digital computer which provides input command signals for the actuators, reads the sensor data, and processes the algorithm to calculate consistent estimates of the modal parameters of the beam. Experimental results are compared with those of simulation analysis.

Thau, F. E.↗

Real-time test of MOCS algorithm during Superflux 1980

A remote sensing experiment was conducted in which success depended upon the real-time use of an algorithm, generated from MOCS (multichannel ocean color sensor) data onboard the NASA P-3 aircraft, to direct the NOAA ship Kelez to oceanic stations where vitally needed sea truth could be collected. Remote data sets collected on two consecutive days of the mission were consistent with the sea truth for low concentrations of chlorophyll a. Two oceanic regions of special interest were located. The algorithm and the collected data are described.

Grew, G. W.↗

A new method for hardware/software integration of strategic systems - Case study of the Space Shuttle

An advanced system integrated self-test has been developed to provide dynamic checkout of all critical subsystems and hardware/software interfaces of the Space Shuttle during pre-launch ground testing. The system modifies hardware sensor data to represent a real flight scenario. This modified data then drives the flight software. The system was sucessfully utilized for three phases of Space Shuttle testing, and will be expanded for use as a maintenance tool.

Haque, S. I.↗

A method for determining the flight readiness of the integrated Space Shuttle system

The Space Shuttle Dynamic Integrated Test (DIT) system is described. The DIT is an open-loop system which makes no attempt to simulate Shuttle sensors, and by which the Shuttle redundancy management system is left unmodified. Open-loop operation is shown to inherently require less computing capacity during a test than the closed-loop alternative. DIT tests have generated a high degree of confidence in the Shuttle hardware, allowing the identification of such problems as a sluggish main fuel valve, which caused a countdown hold seconds before the simulated T-zero, and Main Engine Controller software malfunctions. Attention is given to the combination and substitution of sensor data, the modification of nominal flight software, and the preparation of simulation data. It is noted that greater performance would have been achieved if the interface with DIT had been a design requirement from the outset of Space Shuttle development.

Bacon, I.↗

Space telescope pointing control system

The Space Telescope is a free-flying spacecraft designed for Space Shuttle launch. The Space Telescope's pointing control system slews the optical axis from one target star region of the celestial sphere to the next, and maintains precision pointing for the target star for up to 24 hours. The spacecraft digital computer processes the precision attitude and rate sensor data to generate torque commands for the reaction wheels. The pointing control system has four major elements: the command generator, the control system, the attitude reference processing, and momentum management. The emphasis is on relating design requirements to the hardware and software implementation.

Dougherty, H.↗

Experimental research on structural dynamics and control

This report describes an apparatus at the NASA Langley Research Center for conducting research on dynamics and control of structural dynamics systems. The apparatus consists of a 3.66 m (12 ft.) long flexible beam to which are attached four electromagnetic actuators, nine noncontacting sensors to measure deflection of beam at various locations, and four strain gage type load cells one at each actuator attachment point. The important feature of the apparatus is that the actuators can be controlled and deflection and load sensor data can be processed in real time using the research centers CDC Cyber 175 computer system - thereby allowing research to be conducted on structural dynamics systems using advanced control laws. The facility is described in the report along with a detailed discussion of the actuators used.

Montgomery, R. C.↗

Active control of a flexible beam

Because of inherent low damping and high flexibility, large space structures may require some form of active control of their dynamics. Because of the apparent inability to accurately model the dynamics of these structures, methods for parameter adaptive control are now being developed at Langley. This approach uses a digital computer to process discrete sensor data, identify modal parameters, calculate modal control gains, and then convert the modal forces to real forces. Some of the problems considered are: (1) the possibility that there may be modes to control with limited amounts of hardware, and (2) the required accuracy of identified structural parameters.

Williams, J. P.↗

Nonlinear control of an experimental beam by IMSC

Results are reported from an experiment designed to control the vibratory motion of a beam at NASA, Langley Research Center. The experimental setup consists of a free-free uniform beam acted upon by four electromagnetic force actuators, with the motion being measured by nine displacement sensors. The entire assembly is linked to a CDC Cyber 175 computer which permits on-line real-time computation of the control forces. The control scheme is based on Independent Modal-Space Control (IMSC), whereby the modal forces are computed using a nonlinear, on-off control law. The actuator forces are then synthesized using a linear transformation, resulting in quantized forces. The sensors data is processed by modal filters. It is observed that the controls designed on the basis of the IMSC method are very effective in suppressing the vibratory motion of the beam, even though there is about a 50 percent differene between the actual and the analytically computed frequencies.

Meirovitch, L.↗

Space Telescope pointing control

The Space Telescope Pointing Control System is used to slew the optical axis of the telescope from one target star region of the celestial sphere to the next, and to maintain precision pointing on the target star. A digital computer is employed in the processing of attitude and rate sensor data, in order to generate torque commands for the reaction wheels. The System comprises four major elements: a command generator, the electronic control system, attitude update processing, and momentum management. Emphasis is given to control-related flexibility effects of the Space Telescope's solar cell array and vehicle, and the acquisition methodology and development testing employed, in addition to Pointing Control System design features.

Dougherty, H.↗

High-speed digital signal normalization for feature identification

A design approach for high speed normalization of digital signals was developed. A reciprocal look up table technique is employed, where a digital value is mapped to its reciprocal via a high speed memory. This reciprocal is then multiplied with an input signal to obtain the normalized result. Normalization improves considerably the accuracy of certain feature identification algorithms. By using the concept of pipelining the multispectral sensor data processing rate is limited only by the speed of the multiplier. The breadboard system was found to operate at an execution rate of five million normalizations per second. This design features high precision, a reduced hardware complexity, high flexibility, and expandability which are very important considerations for spaceborne applications. It also accomplishes a high speed normalization rate essential for real time data processing.

Ortiz, J. A.↗

Investigation of design considerations for a complex demodulation filter

The digital design of an adaptive digital filter to be employed in the processing of microwave remote sensor data was developed. In particular, a complex demodulation approach was developed to provide narrow band power estimation for a proposed Doppler scatterometer system. This scatterometer was considered for application in the proposed National Oceanographic survey satellite, on an improvement of SEASAT features. A generalized analysis of complex diagrams for the digital architecture component of the proposed system.

Stoughton, J. W.↗