Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “scaled testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Correlation of full-scale helicopter rotor performance in air with model-scale Freon data

An investigation was conducted in a transonic dynamics tunnel to measure the performance of a 1/5 scale model helicopter rotor in a Freon atmosphere. Comparisons were made between these data and full scale data obtained in air. Both the model and full scale tests were conducted at advance ratios between 0.30 and 0.40 and advancing tip Mach numbers between 0.79 and 0.95. Results show that correlation of model scale rotor performance data obtained in Freon with full scale rotor performance data in air is good with regard to data trends. Mach number effects were found to be essentially the same for the model rotor performance data obtained in Freon and the full scale rotor performance data obtained in air. It was determined that Reynolds number effects may be of the same magnitude or smaller than rotor solidity effects or blade elastic modeling in rotor aerodynamic performance testing.

Yeager, W. T., Jr.↗
NASA NTRS1996

Aspirating Seal Development: Analytical Modeling and Seal Test Rig

This effort is to develop large diameter (22 - 36 inch) Aspirating Seals for application in aircraft engines. Stein Seal Co. will be fabricating the 36-inch seal(s) for testing. GE's task is to establish a thorough understanding of the operation of Aspirating Seals through analytical modeling and full-scale testing. The two primary objectives of this project are to develop the analytical models of the aspirating seal system, to upgrade using GE's funds, GE's 50-inch seal test rig for testing the Aspirating Seal (back-to-back with a corresponding brush seal), test the aspirating seal(s) for seal closure, tracking and maneuver transients (tilt) at operating pressures and temperatures, and validate the analytical model. The objective of the analytical model development is to evaluate the transient and steady-state dynamic performance characteristics of the seal designed by Stein. The transient dynamic model uses a multi-body system approach: the Stator, Seal face and the rotor are treated as individual bodies with relative degrees of freedom. Initially, the thirty-six springs are represented as a single one trying to keep open the aspirating face. Stops (Contact elements) are provided between the stator and the seal (to compensate the preload in the fully-open position) and between the rotor face and Seal face (to detect rub). The secondary seal is considered as part of the stator. The film's load, damping and stiffness characteristics as functions of pressure and clearance are evaluated using a separate (NASA) code GFACE. Initially, a laminar flow theory is used. Special two-dimensional interpolation routines are written to establish exact film load and damping values at each integration time step. Additionally, other user-routines are written to read-in actual pressure, rpm, stator-growth and rotor growth data and, later, to transfer these as appropriate loads/motions in the system-dynamic model. The transient dynamic model evaluates the various motions, clearances and forces as the seals are subjected to different aircraft maneuvers: Windmilling restart; start-ground idle; ground idle-takeoff; takeoff-burst chop, etc. Results of this model show that the seal closes appropriately and does not ram into the rotor for all of the conditions analyzed. The rig upgrade design for testing Aspirating Seals has been completed. Long lead-time items (forgings, etc.) have been ordered.

Bharat Bagepalli↗
NASA NTRS2009

The E-3 Test Facility at Stennis Space Center: Research and Development Testing for Cryogenic and Storable Propellant Combustion Systems

This paper will provide the reader a broad overview of the current upgraded capabilities of NASA's John C. Stennis Space Center E-3 Test Facility to perform testing for rocket engine combustion systems and components using liquid and gaseous oxygen, gaseous and liquid methane, gaseous hydrogen, hydrocarbon based fuels, hydrogen peroxide, high pressure water and various inert fluids. Details of propellant system capabilities will be highlighted as well as their application to recent test programs and accomplishments. Data acquisition and control, test monitoring, systems engineering and test processes will be discussed as part of the total capability of E-3 to provide affordable alternatives for subscale to full scale testing for many different requirements in the propulsion community.

Pazos, John T.↗
NASA NTRS2004

A New Test Method for Material Flammability Assessment in Microgravity and Extraterrestrial Environments

The objective of this research is to modify the well-instrumented standard cone configuration to provide a reproducible bench-scale test environment that simulates the buoyant or ventilation flow that would be generated by or around a burning surface in a spacecraft or extraterrestrial gravity level. We will then develop a standard test method with pass-fail criteria for future use in spacecraft materials flammability screening. (For example, dripping of molten material will be an automatic fail.)

Olson, S. L.↗
NASA NTRSDate not supplied

Multiphase Computational Fluid Dynamics Simulation of Ignition Overpressure and Plume-Water Interaction in the SLS Scale Model Acoustics Test

The solid rocket boosters (SRBs) on the Space Launch System (SLS) generate powerful ignition overpressure (IOP) waves that can potentially damage the vehicle and surrounding ground structures. Based on historical Shuttle experience, the IOP will be mitigated by utilizing an IOP/Sound Suppression (SS) water system which sprays water in and around the SRB and RS-25 engine plumes. However, the complex multiphase physics of the resulting plume-water interaction can lead to undesirable effects, such as high velocity water spray onto the engine nozzles and SRB nozzle side loads. Prior to launch, insight into this environment can be achieved through scale model testing and predictive computational fluid dynamics (CFD) modeling. The Scale Model Acoustic Test (SMAT) was conducted at Marshall Space Flight Center to provide the data necessary to develop the SLS liftoff acoustic environments by using a 5% scale SLS vehicle, fully integrated with a scaled IOP/SS water system, mobile launcher (ML), and tower. NASA engineers have put forth significant effort in validating the Loci/CHEM-Real Fluids multiphase CFD solver on a wet hold down test from the SMAT series. In this paper, the IOP acoustics and plume-water interactions predicted by the CFD model are compared and validated against the experiment, enabling relatively inexpensive, rapid turnaround for multiphase launch environment analyses to support future flights and design evolutions of SLS and other launch vehicles.

John E. Soto↗
NASA NTRSDate not supplied

CFD Simulation of Ignition Overpressure and Plume-Water Interaction in the SLS Scale Model Acoustics Test

The solid rocket boosters (SRBs) on the Space Launch System (SLS) generate powerful ignition overpressure (IOP) waves that can potentially damage the vehicle and surrounding ground structures. Based on historical Shuttle experience, the IOP will be mitigated by utilizing an IOP/Sound Suppression (SS) water system which sprays water in and around the SRB and RS-25 engine plumes. However, the complex multiphase physics of the resulting plume-water interaction can lead to undesirable effects, such as high velocity water spray onto the engine nozzles and SRB nozzle side loads. Prior to launch, insight into this environment can be achieved through scale model testing and predictive computational fluid dynamics (CFD) modeling. The Scale Model Acoustic Test (SMAT) was conducted at Marshall Space Flight Center to provide the data necessary to develop the SLS liftoff acoustic environments by using a 5% scale SLS vehicle, fully integrated with a scaled IOP/SS water system, mobile launcher (ML), and tower. NASA engineers have put forth significant effort in validating the Loci/CHEM-Real Fluids multiphase CFD solver on a wet hold down test from the SMAT series. In this paper, the IOP acoustics and plume-water interactions predicted by the CFD model are compared and validated against the experiment, enabling relatively inexpensive, rapid turnaround for multiphase launch environment analyses to support future flights and design evolutions of SLS and other launch vehicles.

Computational Fluid Dynamics↗
NASA NTRS1991

Response of composite materials to low velocity impact

Orthotropic and quasiisotropic laminates clamped at the edges were impacted by an instrumented falling weight. Five matrix materials, comprising a baseline epoxy, two toughened thermosets, and amorphous and crystalline thermoplastics were studied. For each material, the projected damage area and residual compression strengths and strains were determined as a function of impact energy. Principal conclusions are: (1) incipient damage associated with a prominent load drop during the impact test seems to be decisive for residual properties; (2) subtle rate effects are present with some materials; and (3) results from the small scale tests parallel those in standard tests and may be adequate for screening purposes.

Srinivasan, K.↗
NASA NTRS1991

Response of composite materials to low velocity impact

Orthotropic and quasi-isotropic laminates clamped at the edges were impacted by an instrumented falling weight. Five matrix materials, comprising a baseline epoxy, two toughened thermosets, and amorphous and crystalline thermoplastics were studied. For each material, the projected damage area and residual compression strengths and strains were determined as a function of impact energy. Principal conclusions are: (1) incipient damage associated with a prominent load drop during the impact test seems to be decisive for residual properties; (2) subtle rate effects are present with some materials; and (3) results from the small scale tests parallel those in standard tests and may be adequate for screening purposes.

Srinivasan, K.↗
NASA NTRS2015

Experimental Validation of the Dynamic Inertia Measurement Method to Find the Mass Properties of an Iron Bird Test Article

This presentation describes the DIM method and how it measures the inertia properties of an object by analyzing the frequency response functions measured during a ground vibration test (GVT). The DIM method has been in development at the University of Cincinnati and has shown success on a variety of small scale test articles. The NASA AFRC version was modified for larger applications.

dynamic structural analysis↗
NASA NTRS2015

Testing and Validation of the Dynamic Interia Measurement Method

This presentation describes the DIM method and how it measures the inertia properties of an object by analyzing the frequency response functions measured during a ground vibration test (GVT). The DIM method has been in development at the University of Cincinnati and has shown success on a variety of small scale test articles. The NASA AFRC version was modified for larger applications.

vibration tests↗
NASA NTRSDate not supplied

Thermostructural Testing of PICA-D for NASA Planetary Science Missions

Phenolic Impregnated Carbon Ablator–Domestic (PICA‑D) has been selected as the heatshield thermal protection system (TPS) material for two upcoming NASA planetary science missions: the Dragonfly mission to Titan and the Mars Sample Retrieval Lander (SRL). Early testing revealed differences between PICA‑D and heritage PICA, particularly in in‑plane (IP) tensile stiffness and thermal expansion. Thermostructural analyses using Finite Element Method (FEM) tools subsequently predicted the potential for IP compressive failure in the near‑surface layers of PICA‑D under both Dragonfly and SRL flight environments. Over the past three years, the Dragonfly and SRL teams have carried out an extensive thermostructural qualification campaign to address these concerns and validate PICA‑D for flight. This effort began with a comprehensive mechanical property characterization program at Kratos test laboratories, which significantly improved understanding of PICA‑D mechanical behavior and increased the fidelity of FEM predictions. The teams also conducted six large‑scale test entries at the National Solar Thermal Test Facility (NSTTF) solar tower, exposing PICA‑D articles—including gap fillers and representative design features or flaws—to combined thermal and mechanical loads. The talk will summarize key findings from these mechanical and thermostructural test campaigns and present the current status of PICA‑D qualification for NASA’s planetary science missions.

TPS↗
NASA NTRS1974

Thermal performance of multilayer insulations

Experimental and analytical studies were conducted in order to extend previous knowledge of the thermal performance and gas evacuation characteristics of three selected multilayer insulation (MLI) composites. Flat plate calorimeter heat flux measurements were obtained for 20- and 80- shield specimens using three representative layer densities over boundary temperatures ranging from 39 K (70 R) to 389 K (700 R). Laboratory gas evacuation tests were performed on representative specimens of each MLI composite after initially purging them with helium, nitrogen, or argon gases. In these tests, the specimens were maintained at temperatures between 128 K (230 R) and 300 K (540 R). Based on the results of the laboratory-scale tests, a composite MLI system consisting of 112 unperforated, double-aluminized Mylar reflective shields and 113 water preconditioned silk net spacer pairs was fabricated and installed on a 1.22-m-(4-ft-) diameter calorimeter tank.

Keller, C. W.↗
NASA NTRS2015

Jet-Surface Interaction: High Aspect Ratio Nozzle Test, Nozzle Design and Preliminary Data

The Jet-Surface Interaction High Aspect Ratio (JSI-HAR) nozzle test is part of an ongoing effort to measure and predict the noise created when an aircraft engine exhausts close to an airframe surface. The JSI-HAR test is focused on parameters derived from the Turbo-electric Distributed Propulsion (TeDP) concept aircraft which include a high-aspect ratio mailslot exhaust nozzle, internal septa, and an aft deck. The size and mass flow rate limits of the test rig also limited the test nozzle to a 16:1 aspect ratio, half the approximately 32:1 on the TeDP concept. Also, unlike the aircraft, the test nozzle must transition from a single round duct on the High Flow Jet Exit Rig, located in the AeroAcoustic Propulsion Laboratory at the NASA Glenn Research Center, to the rectangular shape at the nozzle exit. A parametric nozzle design method was developed to design three low noise round-to-rectangular transitions, with 8:1, 12:1, and 16: aspect ratios, that minimizes flow separations and shocks while providing a flat flow profile at the nozzle exit. These designs validated using the WIND-US CFD code. A preliminary analysis of the test data shows that the actual flow profile is close to that predicted and that the noise results appear consistent with data from previous, smaller scale, tests. The JSI-HAR test is ongoing through October 2015. The results shown in the presentation are intended to provide an overview of the test and a first look at the preliminary results.

Aeroacoustics↗
NASA NTRS2011

Fundamental Aeronautics Program. Subsonic Rotary Wing Project: SRW Aeromechanics Overview/UH-60 Airloads Wind Tunnel Test Summary

Objectives: a) Advance the understanding of phenomena in aerodynamics, dynamics, and active control of rotorcraft. b) Develop and validate first-principles tools. c) Acquire data for tool validation from small and large-scale testing of existing and novel rotorcraft configurations. Recent Accomplishments include: (CFD) - Made significant improvements in structured and unstructured rotorcraft CFD methods (OVERFLOW and FUN3D). (Icing) - a) Continued development of high-fidelity icing analysis tools. b) Completed test of oscillating airfoil in Icing Research Tunnel (IRT). c) Developed plans and began detailed preparations for subscale rotor test in IRT.

Norman, Thomas R.↗
DOE OSTI2027

From zonal to nodal capacity expansion planning: Spatial aggregation impacts on a realistic test-case

Solving power system capacity expansion planning (CEP) problems at realistic spatial resolutions is computationally challenging. Thus, a common practice is to solve CEP over zonal models with low spatial resolution rather than over full-scale nodal power networks. Due to improvements in solving large-scale stochastic mixed integer programs, these computational limitations are becoming less relevant, and the assumption that zonal models are realistic and useful approximations of nodal CEP is worth revisiting. Here, this work is the first to conduct a systematic computational study on the assumption that spatial aggregation can reasonably be used for ISO-scale CEP. By considering a realistic, large-scale test network based on the state of California with over 8000 buses, we find that well-designed small spatial aggregations can yield good approximations but that coarser zonal models may result in large distortions of investment decisions, e.g., capacity under-investment of up to 41% for the lowest resolution model considered.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2024

Non-contact Real-time Target Health Monitor

Targets are an essential part of many accelerator-based experiments, yet their constant radiation exposure eventually affects their internal structure and, consequently, their properties. Current methods typically involve either direct contact with the target or complete removal of the system, which may not be the most efficient for assessing radiation damage. For this reason, a system has been proposed that will monitor a target s radiation damage without the need for direct contact or removal. This sensor will achieve this by measuring the reflectivity of S- and P-polarized waves, which are expected to change measurably due to radiation-induced alterations. As is commonly done, smaller-scale tests were performed to ensure that the necessary equipment was functioning correctly. Once all equipment is tested, the next step will be to perform reflectivity measurements using a tungsten sample, a material often used in targets. Longer-term work will involve scaling up the system and implementing higher-energy beams. This sensor will enable a more comprehensive study of radiation damage in materials and is being considered for projects such as Mu2e, Mu2e-II, LBNF, AMF, and muon colliders.

Agosto Reyes, Alanice↗