Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “rock”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Experimental study of three-dimensional CO 2 -water drainage and fracture-matrix interactions in fractured porous media

Estimation of CO 2 storage capacity in fractured porous reservoirs requires a better understanding of the CO 2 -water flow fundamentals in fracture-matrix systems. There are few core-flood experiments on three-dimensional CO 2 -water drainage in a fracture-matrix system, yet none have examined the impacts of the capillary continuity of fractures and fracture-matrix interactions. In this study, twelve drainage experiments were conducted in four fracture-matrix columns, each comprising a vertical stack of a cylindrical rock core, a filter paper serving as an analogue to a horizontal fracture, and a ceramic plate. Here, the core sample was surrounded by open space at the top and circumferential sides to model fractures, allowing for 3-D CO 2 -water drainage in the rock core and displaced water draining across the horizontal fracture. X-ray computed tomography was conducted to visualize the dynamic invasion/drainage processes in four rock core samples showing contrasts in anisotropy, permeability, and heterogeneity. Experimental results show (1) the equilibrium CO 2 saturations in the rock matrix vary from 0.10 to 0.60 at controlled capillary pressures up to 200 kPa, (2) the CO 2 saturations in the matrix increase with water saturation in the horizontal fracture resulting in better capillary continuity for water to drain across the fracture, and (3) the fracture water saturation can be enhanced by the non-uniform fracture capillary pressure and countercurrent flow of CO 2 and water across the fracture-matrix interface. In the case of high fracture water saturation, matrix CO 2 saturation largely depends on matrix anisotropy and heterogeneity. The core-scale experimental results contribute to understand the fracture-matrix interactions and CO 2 storage efficiency in fractured porous media.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

A comparative investigation of the effect of gas type on foam strength and flow behavior in tight carbonates

Foam generation technique has been practically applied to overcome gas mobility issue during enhanced oil recovery (EOR) processes. Incorporated with the utilized gas, the capability of foaming agent to generate persistent foam determines the flow performance under reservoir conditions. Here, in this study, we first identified the surfactants with excellent phase behavior and foaming properties and, second, evaluated their bulk foam performance with different gases, including N 2 , CO 2 , and hydrocarbon gas (CH 4 ) under high-pressure and high-temperature conditions. In bulk, the foam generated with the high-density gas, i.e., CO 2 , exhibited the greatest foamability but the lowest foam stability. With amidoamine oxide-based surfactant, CH 4 -foam was found to be more stable than N 2 -foam, while the opposite was observed for sulfobetaine-based surfactant. The most effective surfactant was later used to perform flow experiments on two tight carbonate rocks, including Minnesota Norther Cream Buff and Edwards limestone, with permeabilities of ~0.8 and 16 mD, respectively. The core-flooding experiments showed that the optimum quality of CO 2 -foam was lower than that of N 2 - and CH 4 -foams. For a given flow rate and fixed foam quality, the steady-state strength followed the descending order of CH 4 -, N 2 -, and CO 2 -foam. However, in general, the difference in foam strength between N 2 - and CH 4 -foams was insignificant when the total flow rate was varied. We also found that the variation in rock permeability had a greater effect on the strength of the CO 2 -foam compared to those generated with N 2 and CH 4 . In the presence of oil, the shear-thinning behavior of all foams was found more prominent. The increase in oil saturation had a more adverse effect on the strength of N 2 - and CH 4 -foams, particularly in the higher permeability rock. The results indicated that the foam strength, which is key in the effectiveness of foam EOR applications, is greatly influenced by several factors such as gas density, gas solubility in water, the presence of oil, and rock permeability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Reduced-order modeling of near-field THMC coupled processes for nuclear waste repositories in shale

Performance assessment (PA) of geologic radioactive waste repositories requires three-dimensional simulation of highly nonlinear, thermo-hydro-mechanical-chemical (THMC), multiphase flow and transport processes across many kilometers and over tens to hundreds of thousands of years. Integrating the effects of a near-field geomechanical process (i.e. buffer swelling) into coupled THC simulations through reduced-order modeling, rather than through fully coupled geomechanics, can reduce the dimensionality of the problem and improve computational efficiency. In this study, PFLOTRAN simulations model a single waste package in a shale host rock repository, where re-saturation of a bentonite buffer causes the buffer to swell and exert stress on a highly fractured disturbed rock zone (DRZ). Three types of stress-dependent permeability functions (exponential, modified cubic, and Two-part Hooke’s law models) are implemented to describe mechanical characteristics of the system. Overall, our modeling study suggests that compressing fractures reduces DRZ permeability, which could influence the rate of radionuclide transport and exchange with corrosive species in host rock groundwater that could accelerate waste package degradation. Less permeable shale host rock delays buffer swelling, consequently retarding DRZ permeability reduction as well as chemical transport within the barrier system.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Laboratory evaluation of cyclic underground hydrogen storage in the Temblor sandstone of the San Joaquin Basin, California

Underground Hydrogen Storage (UHS) in depleted oil and gas reservoirs could provide a cost-effective solution to balance seasonal fluctuations in renewable energy generation. However, data and knowledge on UHS at subsurface conditions are limited so it is difficult to estimate how effective this type of storage could be. In this study, we perform high pressure experiment to measure the effectiveness of cyclic hydrogen (H 2 ) storage in a specimen of Temblor sandstone retrieved from the San Joaquin Basin of California. Our experiment mimics reservoir pressure conditions to measure H 2 -brine relative permeability and fluid-rock interactions over the course of ten charging and discharging cycles. Initial gas breakthrough occurred at 15 % to 25 % H2 saturation in the specimen with 3 % NaCl brine as the resident fluid. Continuing injecting to 4 pore volumes (PV) of H 2 yielded an asymptotic H 2 saturation of 38 % to 41 %, a level often referred to as the irreducible gas saturation based on two-phase flow. The boundary condition in this study mimics the near wellbore region, which experiences bi-directional H 2 flow. This bi-directional flow led to evaporative drying of the specimen resulting in 94 % H 2 saturation at the end of 10th cycle. This indicates that cyclic flow and evaporative drying can lead to more efficient reservoir storage where a larger fraction of the reservoir porosity is usable to store H 2 . The produced gas stream consisted of H 2 mixed with 8 % to 22 % H 2 O, indicating formation dry-out by evaporation. Meanwhile, produced water chemistry indicated calcite and silicate dissolution, with calcite sourced from fossil fragments. This led to a loss of cementation and weakened the rock sample. Combined, our results indicate dry-out, compaction, increased H 2 saturation, rock weakening, and permeability loss during cyclic UHS. Overall, we anticipate that the combined effects should lead to higher than anticipated UHS storage efficiency per volume of sandstone reservoir rock.

08 HYDROGEN↗
DOE OSTI2023

Wettability variation and its impact on CO 2 storage capacity at the Wyoming CarbonSAFE storage hub: An experimental approach

Meeting global and national net zero carbon emission targets will require geologic carbon disposal. The U.S. Department of Energy (DOE) has accordingly funded significant research in this area, including the Wyoming CarbonSAFE project at Dry Fork Station (DFS) in Campbell County, Wyoming. This work studied wettability on micro- and macro-scales, CO 2 storage potential, and the correlation between the two to support the Wyoming CarbonSAFE project’s subsurface assessment. During the study, a target formation’s wettability was found to affect how much CO 2 can be stored in a given formation. Here, in this study, representative rock samples were selected from the target storage formations— Lakota, Hulett, and Minnelusa—based on the heterogeneity of the lithology, permeability, and porosity of the respective formations. The rock samples are all fine-grained sandstone with variable cementation and bedding structure, including different scales of laminated bedding. The porosity and permeability vary within the range of 9.0–14.3% and 0.1–28.9 mD, respectively. These rock samples were prepared for the micro-scale wettability (contact angle measurement), macro-scale wettability (wettability index derived from unsteady-state flow characterization for the core plugs), and CO 2 storage evaluation. The macro-scale experiments suggested that wettability appeared to dominate the CO 2 storage potential performance during the drainage process, where less water-wet behavior promoted higher CO 2 storage potential. The micro-scale wettability tests showed that the rock samples at the studied reservoir conditions behaved water-wet and became more water-wet as pressure increased. This kind of wettability change discourages further CO 2 storage potential yet benefits the CO 2 residual trapping as the CO 2 injection proceeds for the studied area. The results allow the recommendation of the best reservoir candidate for storage based on wettability that affects CO 2 storage. The work presented in this study provides valuable insights into wettability’s effect on the CO 2 storage capacity and wettability’s importance when identifying the optimal CO 2 storage formation to meet the project’s goals.

58 GEOSCIENCES↗
DOE OSTI2026

The solubility of ErPO 4 and Er speciation in hydrothermal fluids at varying pH and salinity between 350 and 450 °C

The rare earth elements (REE) are important for the green-energy transition and can be incorporated into the REE phosphates, such as xenotime-(Y), which also hosts heavy REE (Tb– Lu). Xenotime-(Y) is a common accessory mineral in metamorphic rocks and a range of mineral deposits where it controls the mobility of heavy REE, however, the impact of high temperature aqueous fluids on the behavior of heavy REE is largely unknown. Thermodynamic modeling can be utilized as a tool to predict the mobility of REE in hydrothermal aqueous fluids, but must be supported by accurate experimental data. Here, we measured the solubility of endmember synthetic xenotime-structured ErPO4 in NaCl-HCl-NaOH-bearing aqueous solutions at 350 °C and water vapor saturation pressure, at 400 and at 450 °C and 500 bar using batch-type Inconel reactors. Erbium speciation was investigated as a function of pH from 2.8 to 8, where Er chloride species are predominant at acidic conditions (pH <3) and Er hydroxyl complexes are predominant at near- neutral to alkaline conditions (pH >3). At pH 7–9, the measured ErPO 4 solubility (-9.8 to -7.5 log m Er ) is up to 2.5 orders of magnitude lower than thermodynamic predictions (-9.4 to -6.7 log m Er ) using existing thermodynamic databases. At pH 2–3, the predicted ErPO 4 solubility is ~0.5 orders of magnitude higher at 350 °C and ~1 order of magnitude lower at 450 °C compared to experimentally measured Er concentrations. The thermodynamic properties of aqueous Er species were therefore revised in this study. The partial molal Gibbs energy of formation (Δ f G 0 T,P ) for aqueous Er hydroxyl and chloride species are optimized using GEMSFITS and the logarithmic formation constants (logβ n ( Cl,OH) ) were derived at each experimental temperature and pressure. The updated thermodynamic properties for Er hydroxyl species (Er(OH) +2 , Er(OH) 2 + , and Er(OH) 3 0 ) show that their stability shifts to more acidic conditions at and below 400 °C. The Er chloride species (ErCl +2 and ErCl 2 + ) show increased stability compared to Er hydroxyl species at temperatures of 450 °C and 0.01 mol/kg NaCl. The updated thermodynamic properties are implemented into the GEM-Selektor modeling package to investigate the mobility of Er in saline hydrothermal fluids in equilibrium with alkaline rocks. Importantly, the updated properties for Er hydroxyl species result in low Er solubility at rock equilibrated pH conditions due to an expanded hydroxyl predominance zone, but lower aqueous complex stability overall, whereas previous models suggest greater stability for aqueous Er species. Furthermore, ErPO 4 solubility increases with decreasing temperature due to the deprotonation of HCl, which increases the acidity of hydrothermal fluids and the availability of Cl - to complex with the REE. These simulations highlight how fluid-rock reaction and temperature affect the mobility of REE in hydrothermal ore-forming systems.

58 GEOSCIENCES↗
DOE OSTI2021

Modeling heat transport processes in enhanced geothermal systems: Validation study from EGS Collab Experiment 1

Heat recovery from enhanced geothermal systems (EGS) is a complex process involving heat transport in both fracture networks and rock formations. A comprehensive understanding of and the ability to model the underlying heat transport mechanisms is important for the success of EGS but remains challenging in practice due to the generally insufficient characterization of EGS reservoirs. In the present study, we analyze an extensively monitored intermediate-scale EGS field experiment performed in a well-characterized testbed. The high-resolution, high-quality measurements from the field experiment enable the development of a high-fidelity model incorporating a well-constrained fracture network. Based on the field experiment, we investigate the complex heat transport processes in an EGS-relevant environment and validate the capability of a numerical approach in simulating these inherently coupled heat transport processes. A series of numerical simulations were performed to study the effects of different heat transport mechanisms, including thermal convection with fracture flow, thermal conduction in rock formations, and the Joule-Thomson effect. The agreement of thermal responses between field measurements and simulation results indicates that our numerical approach can appropriately model the heat transport processes pertaining to heat recovery from EGS reservoirs.

Wu, Hui↗
DOE OSTI2023

Role of pH and Eh in geothermal systems: Thermodynamic examples and impacts on scaling and corrosion

The global demand for sustainable and clean renewable energy sources is rapidly increasing to meet growing energy demands while curtailing the CO2 emissions from fossil fuels. Harnessing the natural heat or geothermal energy of the Earth's interior can simultaneously address both issues by offering a clean and renewable energy source. Enhanced geothermal systems require the movement and cycling of fluid through a porous rock media. Further, this process requires understanding the chemistry occurring at the fluid-rock and fluid-metal interfaces both in the deep subsurface and surface, where fluid is circulated for energy transfer or storage. In this review paper, we evaluate the current state of research on how two key variables, pH and Eh, control the fluid-rock reactions controlling mineral scaling and the steel corrosion reactions associated with geothermal systems. These variables are frequently used in geochemical modeling to predict chemical reactions in geothermal systems. Prediction of the fluid-rock behavior can be utilized to formulate new strategies for extending the lifespan and efficiency of heat extraction and utilization and maximizing the safety of geothermal systems.

15 GEOTHERMAL ENERGY↗
DOE OSTI2025

Preferential adsorption of noble gases in zeolitic tuff with variable saturation: A modeling study of counter-intuitive diffusive-adsorptive behavior

Noble gas transport through geologic media has important applications in the prediction and characterization of measured gas signatures related to underground nuclear explosions (UNEs). Retarding processes such as adsorption can cause significant species fractionation of radionuclide gases, which has implications for measured and predicted signatures used to distinguish radioxenon originating from civilian nuclear facilities or from UNEs. Accounting for the effects of variable water saturation in geologic media on tracer transport is one of the most challenging aspects of modeling gas transport because there is no unifying relationship for the associated tortuosity changes between different rock types, and reactive transport processes such as adsorption that are affected by the presence of water likewise behave differently between gas species. In this study, we perform numerical diffusive-adsorptive transport simulations to estimate gas transport parameters associated with bench-scale laboratory diffusion cell experiments measuring breakthrough in zeolitic and non-zeolitic rocks for a gaseous mixture of xenon, krypton, and SF 6 at varying degrees of water saturation (S w ). Counter-intuitive transport behavior was observed in the zeolitic rock experiments whereby breakthrough concentrations were significantly higher when the core was partially saturated (S w = 17 %) than under dry (S w = 0 %) conditions. Breakthrough of xenon was especially retarded in the dry core – likely due to comparatively high affinity of xenon for zeolitic adsorption sites – and estimated effective diffusion coefficients for all gases were approximately an order of magnitude lower than what is predicted by porosity-tortuosity models. We propose the counter-intuitive behavior observed is because water infiltration of zeolite nanopores reduces both the adsorptive capacity of the rock and the tortuosity of connected flow paths. We developed a two-site competitive kinetic Langmuir adsorption reaction for the porous media transport simulator in order to constrain transport parameters within zeolitic tuff, where differential adsorption to zeolite and non-zeolite pores was observed. We determined that liquid saturation-dependent diffusive-adsorptive transport is affected by subtle and at times competing processes that are specific to different gases, which have a significant overall influence on effective transport parameters.

58 GEOSCIENCES↗
DOE OSTI2023

Radiation-induced alteration of sandstone concrete aggregate

This study investigates the alteration of felsic sandstone-type rock, which is used as a coarse aggregate in concrete, subject to the effects of gamma-ray and neutron irradiation. The effects of three gamma-ray doses (27, 55, and 108 MGy) and four neutron fluence levels (1.22, 2.19, 6.99, and 14.30 × 10 19 n/cm 2 , $E$ ≥ 0.01 MeV) were investigated. Quartz and albite were found to be the major rock-forming minerals, with microcline intermediates, chlorite, and muscovite as the minors. Gamma rays caused no significant changes to the physical properties of the sandstone aggregates, even at high doses (108 MGy). In contrast, neutron irradiation caused alterations that became more pronounced at higher neutron fluences. The solid was confirmed to expand through metamictization of the rock-forming minerals. Quartz and muscovite were the most affected phases, whereas albite and microcline intermediates were only slightly affected, and chlorite was almost unaffected. The decrease in density was measured by He and water pycnometry, and this value was almost reproduced by calculations using the rock-forming mineral composition of the pristine sample measured using X-ray powder diffraction/Rietveld analysis and the cell volume change of the major forming minerals. In addition, light optical microscopy and scanning electron microscopy images confirmed the presence of intergranular and intragranular cracks. Intergranular cracks appeared to have initiated from the quartz grains, which expanded significantly. The intragranular cracks were frequently observed in the albite and microcline intermediates. These cracks can be described as radial cracks starting from the expanding quartz, caused by enforced displacement for deformation consistency with quartz expansion. The crack area ratio quantified by SEM image analysis corresponds to the discrepancy of the volume expansion difference calculated by He or water pycnometry and dimensional change measurements. In conclusion, an evaluation of solid expansion and crack openings in aggregates is important to estimate concrete degradation.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Coupled Time-Lapse Full-Waveform Inversion for Subsurface Flow Problems Using Intrusive Automatic Differentiation

We describe a novel framework for estimating subsurface properties, such as rock permeability and porosity, from time-lapse observed seismic data by coupling full-waveform inversion (FWI), subsurface flow processes, and rock physics models. For the inverse modeling, we handle the back propagation of gradients by an intrusive automatic differentiation strategy that offers three levels of user control: (1) At the wave physics level, we adopted the discrete adjoint method in order to use our existing high-performance FWI code; (2) at the rock physics level, we used built-in automatic differentiation operators from the TensorFlow backend; (3) at the flow physics level, we implemented customized partial differential equation (PDE) operators for the multiphase flow equations. The three-level coupled inversion strategy strikes a good balance between computational efficiency and programming efforts, and when the gradients are chained together, it constitutes a coupled inverse system. Our numerical experiments demonstrate that the three-level coupled inverse problem is superior in terms of accuracy to a traditional decoupled inversion strategy. Additionally, our method is able to simultaneously invert for parameters in empirical relationships such as the rock physics models. Our proposed inverted model can be used for reservoir performance prediction and reservoir management/optimization purposes.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Comparison of Biotite Elastic Properties Recovered by Spherical Nanoindentations and Atomistic Simulations — Influence of Nano-Scale Defects in Phyllosilicates

Phyllosilicate minerals, due to their sheets structure and morphology, are known to cause anisotropy in bulk rock properties and make the bulk rock more compliant. Accurately characterizing the micromechanical behavior of phyllosilicate minerals from laboratory observations, which eventually translates to the bulk rock behavior, is still challenging due to their fine-grained nature. Recent advances in atomistic simulations open the possibility of theoretically investigating such mineral mechanical behavior. We compare the elastic properties of biotites recovered by spherical nanoindentation with those predicted from density functional theory (DFT) simulations to investigate to what extent theoretical predictions reproduce actual phyllosilicate properties. Spherical nanoindentation was conducted using schist rocks from Poorman Formation, South Dakota, USA, to recover continuous indentation stress-strain curves. Loading in the layer-normal orientation shows an average indentation modulus (M) of about 35 GPa, while loading in the layer-parallel orientation gives a higher average of about 95 GPa. To facilitate comparison, the elastic stiffness constants (cij) determined from DFT were converted to indentation modulus (M) using solutions proposed in this study. The majority of the nanoindentation modulus results are below the values inferred from the simulation results representing ideal defect-free minerals. We suggest that crystal defects present at the nano-scale, potentially ripplocations, are the dominant cause of the lower indentation modulus recovered from nanoindentation compared to those inferred from DFT simulations. Results highlight the importance of acknowledging the defects that exist down to the nano-scale as it modifies the mechanical properties of phyllosilicates compared to its pure defect-free form.

58 GEOSCIENCES↗
DOE OSTI2026

Amapari Marker Band Metal‐Enrichments: Potential Mechanisms and Implications for Surface and Subsurface Water and Weathering in Gale Crater

NASA's Curiosity rover is exploring a 5 km tall sedimentary mound that is hypothesized to record the transition from a warm and wet (phyllosilicate-rich) to a cold and drier (sulfate-rich) Mars. Evidence of magnesium sulfate-bearing rock has shown that Curiosity has crossed through this phyllosilicate-sulfate transition. Recently, Curiosity arrived at the Amapari Marker Band, a darker, indurated unit that can be traced laterally for tens of kilometers in orbiter images. Here, Curiosity found evidence for a very broad lake, and bedforms interpreted as wave-ripple laminated sedimentary rock that likely was deposited in shallow water in the explored location, before becoming a deeper lake. These rocks are enriched in Fe, Mn, and Zn which has major implications for groundwater paleohydrology in Gale crater. Three formation hypotheses are considered: concretion formation during early diagenetic alteration of shallow lake sediments, laterization or leaching of the sediments, and addition of Fe, Mn, and Zn by a mildly acidic and reducing groundwater interacting with a redox and/or pH front in a stratified lake. The preferred interpretation of the metal enrichments within the Amapari Marker band sedimentary rocks is that they formed in a shallow water environment at a redox and/or pH front within the ripple unit, which drove precipitation and concentration of metals. If the enrichments are due to groundwater alteration, these processes could link subsurface and surface environments. Water and the presence of high amounts of redox sensitive elements and other metals are favorable indicators for habitability.

58 GEOSCIENCES↗
DOE OSTI2021

Quantitative Evaluation of Top Coal Caving Methods at the Working Face of Extra‐Thick Coal Seams Based on the Random Medium Theory

Adopting an effective top coal caving method is the key to enhancing coal recovery and reducing gangue content for the fully mechanized top coal caving working face with extra‐thick coal seams. In this study, the movement of coal particles generated during top coal caving is considered to follow a normal distribution. Then, the caving body and coal‐rock settlement along the working face during the caving process are studied based on both the random media theory and probability theory. Accordingly, the optimal caving interval and caving sequences are determined, and a novel interval symmetrical coal caving method is proposed. The proposed method is systematically verified with results from physical similarity tests, and different caving methods are assessed by field tests. The results show the following: (1) The coal‐rock settlement and the caving body demonstrate clear axial symmetrical features along the working face; the size of the caving body increases as the caving height grows and its shape turns progressively from semicircular to semielliptical with a lower foot of the coal‐rock settlement. (2) The caving interval is derived using the sum of the radii of the coal‐rock settlement curves formed by the two largest caving bodies. (3) The symmetrical caving approach provides a symmetrical space for the subsequent movement of the broken top coal, which enables a uniform development of the caving body. (4) Compared with the traditional sequential coal caving method with the same number of supports, the interval symmetrical caving method results in a 21.7% of coal production increase, 17% caving rate promotion, and a shortened caving time by 23.4%. (5) The interval symmetrical caving method is found to improve the controllability of the caving process at the fully mechanized top coal caving working face. In general, this work presents a theoretical approach to select the optimal caving methods for the fully mechanized caving working face in extra‐thick coal seams for an improved production efficiency of the work face. The results of this study can also provide theoretical significance and referencing value for quantitative analyses of the coal caving methods for work faces with similar geological conditions.

Jiulin, Shi (ORCID:0000000155819062)↗
DOE OSTI2023

Wettability Alteration with Weak Acid-Assisted Surfactant Flood

Oil-wetness and heterogeneity are two key reasons for low oil recovery by waterflooding in carbonate reservoirs. Surfactants have been effective in altering the oil-wet matrix to a more water-wet condition and initiating spontaneous imbibition. Because it takes time for the surfactant to alter wettability, oil recovery from the tight matrix is slow and sometimes not economically feasible. Acids have the potential of dissolving minerals, which may alter wettability. In this study, the enhanced oil recovery (EOR) performance of an acid-assisted surfactant solution, a novel technique, was evaluated for low-temperature applications. A set of acids and their acetates were tested. Bulk rock-acid reaction, wettability alteration (WA) tests, and spontaneous imbibition measurements were conducted at reservoir temperature (35°C) to identify effective candidates. Coreflood tests were then performed to evaluate the selected acid-surfactant formulations. Before and after a coreflood test, the core was scanned using micro-computed tomography (CT) to investigate pore structure alteration. Bulk reaction measurements showed that weak acids, especially acetic acid (AA), have the desired low reaction rates at 35°C. WA tests showed that AA can remove the crude oil off the rock surface and alter wettability through mineral dissolution. The surfactant can reduce contact angles from 160° to 58°; adding acid into the surfactant can further reduce it to 52°. Spontaneous imbibition experiments showed the synergy between the acid and the surfactant; the AA-surfactant solution had the highest oil recovery (62.6%) among acid-surfactant formulations. The acid improves the WA efficiency by the surfactant through surface mineral dissolution and lower ζ-potential. The imbibition transports the acid-surfactant solutions into the matrix, which minimizes face dissolution. Coreflood tests show that the AA-surfactant flood can increase the oil recovery rate and recover about 8% more oil compared to the surfactant flood. Micro-CT showed that a few mineral particles were transported along the core and partially plugged pore throats, which reduced permeability and diverted flow leading to improved oil recovery. Here, the transport of the acid in reservoirs and the potential plugging issues have to be carefully evaluated in future studies.

58 GEOSCIENCES↗
DOE OSTI2021

Oxygen isotope ratios in zircon and garnet: A record of assimilation and fractional crystallization in the Dinkey Dome peraluminous granite, Sierra Nevada, California

Abstract The 119 Ma Dinkey Dome pluton in the central Sierra Nevada Batholith is a peraluminous granite and contains magmatic garnet and zircon that are complexly zoned with respect to oxygen isotope ratios. Intracrystalline SIMS analysis tests the relative importance of magmatic differentiation processes vs. partial melting of metasedimentary rocks. Whereas δ18O values of bulk zircon concentrates are uniform across the entire pluton (7.7‰ VSMOW), zircon crystals are zoned in δ18O by up to 1.8‰, and when compared to late garnet, show evidence of changing magma chemistry during multiple interactions of the magma with wall rock during crustal transit. The evolution from an early high-δ18O magma [δ18O(WR) = 9.8‰] toward lower values is shown by high-δ18O zircon cores (7.8‰) and lower δ 18O rims (6.8‰). Garnets from the northwest side of the pluton show a final increase in δ18O with rims reaching 8.1‰. In situ REE measurements show zircon is magmatic and grew before garnets. Additionally, δ18O in garnets from the western side of the pluton are consistently higher (avg = 7.3‰) relative to the west (avg = 5.9‰). These δ18O variations in zircon and garnet record different stages of assimilation and fractional crystallization whereby an initially high-δ18O magma partially melted low-δ18O wallrock and was subsequently contaminated near the current level of emplacement by higher δ18O melts. Collectively, the comparison of δ18O zoning in garnet and zircon shows how a peraluminous pluton can be constructed from multiple batches of variably contaminated melts, especially in early stages of arc magmatism where magmas encounter significant heterogeneity of wall-rock assemblages. Collectively, peraluminous magmas in the Sierran arc are limited to small <100 km2 plutons that are intimately associated with metasedimentary wall rocks and often surrounded by later and larger metaluminous tonalite and granodiorite plutons. The general associations suggest that early-stage arc magmas sample crustal heterogeneities in small melt batches, but that with progressive invigoration of the arc, such compositions are more effectively blended with mantle melts in source regions. Thus, peraluminous magmas provide important details of the nascent Sierran arc and pre-batholithic crustal structure.

Geochemistry & Geophysics↗
DOE OSTI2020

Abstract for Joint Work Statement 5 (AGMT-1005) between National Energy Technology Laboratory (NETL) and ExxonMobil Research and Engineering Company (EMRE) to Umbrella CRADA (AGMT-0922)

NETL and EMRE will focus on fundamental questions aimed at understanding the controlling factors on tight oil production flow paths and how those flow paths are impacted by the hydraulic fracturing fluids and processes. Key questions for the Parties to explore include the following: Are there geochemical reactions between hydrocarbon producing tight reservoir rocks and water from the hydraulic fracturing process? To what extent does this alteration impact oil production? By further characterizing the flow paths near the fracture-matrix interface, what is the relative impact of geochemical process compared to geomechanical changes on production? This research focuses on rock types found in the Permian Basin. The research drives along two main thrusts: 1) Inorganic geochemistry studies involving representative rock types, connate fluids (hydrocarbons and water), and injected fluids (fracturing water) will be conducted in order to bound the kinetics of key mineral reactions; 2) Computed tomography (CT) for characterization of flow paths as a function of geochemical and geomechanical processes associated with hydraulic fracture creation and reservoir production. The objective of this characterization is to ultimately develop new insights into the role geochemical and geomechanical effects play on production. The work will include studying mechanical damage near the rock-fracture interface and how it impacts flow properties.

02 PETROLEUM↗