Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “repeatability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
NASA NTRS1942

Effects of Range of Stress and of Special Notches on Fatigue Properties of Aluminum Alloys Suitable for Airplane Propellers

Laboratory tests were made to obtain information on the load-resisting properties of X76S-T aluminum alloy when subjected to static, impact, and repeated loads. Results are presented from static-load test of unnotched specimens in tension and in torsion and of notched specimens in tension. Charpy impact values obtained from bend tests on notched specimens and tension impact values for both notched and unnotched specimens tested at several different temperatures are included. The endurance limits obtained from repeated bending fatigue tests made on three different types of testing machine are given for unnotched polished specimens, and the endurance limits of notched specimens subjected to six different ranges of bending stress are also reported. The results indicated that: (a) polished rectangular specimens had an endurance limit about 30 percent less than that obtained for round specimens; (b) a comparison of endurance limits obtained from tests on three different types of machine indicated that there was no apparent effect of speed of testing on the endurance limit for the range of speeds used (1,750 to 13,000 rpm). (c) the fatigue strength (endurance limit) of the X76S-T alloy was greatly decreased by the presence of a notch in the specimens; (d) no complete fractures of the entire specimens occurred in notched fatigue specimens when subjected to stress cycles for which the mean stress at the notch during the cycle was a compressive stress; for this test condition a microscopic cracking occurred near the root of the notch and was used as a criterion of failure of the specimen. (e) as the mean stress at the notch was decreased from a tensile (+) stress to a compressive (-) stress, it was found that the alternating stress that could be superimposed on the mean stress in the cycle without causing failure of the specimens was increased.

ALUMINUM ALLOYS-ALCOA X76ST-FATIGUE↗
NASA NTRS1954

Multiple over-all performance and rotating-stall characteristics of a 15-stage experimental axial-flow compressor at an intermediate speed

The 15-stage experimental axial-flow compressor was investigated at 78.5 percent of design speed, which falls in the region of the surge-limit line discontinuity. In this region indications of multiple characteristic curves of compressor operation had been found. On the basis of previous stage-matching analyses, these multiple performance characteristics appear to be the result of multiple-valued stage performance characteristics. At this speed of 78.5 percent, at least six separate characteristic performance curves were found, associated with five different numbers of rotating stall configurations, from zero to four stall zones. It was difficult in many cases to repeat a given performance curve by approaching the test speed in a similar manner, and many of the curves were not stable, the no-stall curve being the only definitely repeatable one. In some cases a jump from one curve to another took place at the surge point, while in others the change occurred within the usual limits of a conventional performance curve and without any sudden obvious changes in observed data. In general, as the number of zones in the rotating-stall pattern decreased, the maximum weight flow, maximum efficiency, and maximum pressure ratio of the resultant curves were increased. It appears, therefore, that multiple performance characteristics at the given speed are encountered in the region of the discontinuity of the surge line.

Lucas, James G↗
NASA NTRS1994

Cryogenic Multichannel Pressure Sensor With Electronic Scanning

Array of pressure sensors operates reliably and repeatably over wide temperature range, extending from normal boiling point of water down to boiling point of nitrogen. Sensors accurate and repeat to within 0.1 percent. Operate for 12 months without need for recalibration. Array scanned electronically, sensor readings multiplexed and sent to desktop computer for processing and storage. Used to measure distributions of pressure in research on boundary layers at high Reynolds numbers, achieved by low temperatures.

Hopson, Purnell, Jr.↗
NASA NTRS1993

Kennedy Space Center processing of Shuttle small payloads

There are many steps involved in preparing a payload for a mission into space on the Space Shuttle. Operations at the John F. Kennedy Space Center (KSC) are the last of those steps for the hardware before the payload is launched. To assure a successful and efficient KSC processing flow, a great deal of planning between the Robert H. Goddard Space Flight Center (GSFC) and KSC personnel is required before the payload arrives at KSC. After arrival, pre-flight operations occur between payload personnel, GSFC personnel, and KSC personnel for integration of the payload into its carrier (if required), in preparation for installation into a Orbiter. Once installed into an Orbiter, final test(s), checkout, and close-out of the payload is performed by GSFC and KSC personnel before launch. Mission support varies depending on the payload flying, but once the mission is complete and the Orbiter has returned to KSC, post-flight operations begin. This usually involves a reverse flow of the pre-flight operations. KSC operations conclude when the payload, its ground support equipment (GSE), and personnel depart KSC. A list of lessons learned is generated at the end of each payload flow, to avoid repeating the same mistakes (if any) for the next payload or for multiple repeat flights of the same payload. Always monitored are planned changes that may affect the payloads, GSE, KSC facilities, payload personnel, GSFC personnel, and/or KSC personnel.

Haddad, Michael E.↗
NASA NTRS1993

Ridge belt-related scarps and troughs: Compressional crustal bending on Venus

Cytherean ridge arcs resulted in crustal shortening in places with either the strongest compression or weakest surface layers. Arcuate scarps on or close to the edge of the ridge arcs were compressional fronts formed by overthrust over or subduction of adjacent lowland. These ridge arcs became wider due to the propagation of new ridge formation close to previous one(s). As this process repeated itself with time, the crust became thicker and the foreland was bent either due to the excess load, overthrust or subduction event. The Salme Dorsa arc measures 100 km in width and 600 km in length. It consists of a horseshoe-like set of ridges and grooves on a gently sloping lowland. The westward arcuate ridge belt indicates lateral compressional stresses and crustal deformation from SE against the southern Ishtar Terra foreland plain. The trough on the western side of the ridge belt and tensional grabens close to the crest of the bulge to the west of the trough are due to the crustal bending and indicate effects of the load and thrust. Compression and relative movement from southeast against and over the foreland planitia have resulted in ridge belt, trough and bulge formation. The load- and/or stress-induced bending of the uppermost crust allows some estimations of the uppermost elastic lithosphere thickness. Repeated folding and thrust faulting of surface layers due to compression are indicated by four more ridge belts located close to Salme Dorsa. The northeasternmost one has short ridges located in troughs. The west-opening arcuate ridge belt interlocks with the Salme Dorsa horseshoe.

Raitala, J.↗
NASA NTRS1994

Theoretical investigation of variable periodicity (graded) multilayers for hard x ray applications

The objective of this research was to investigate the possibility of increasing the useful bandwidth of multilayer mirrors. Mirrors 'constructed' with non-periodically spaced reflecting surfaces were considered. These structures included depth-graded and laterally-graded mirrors as well as those with reflectors located via a log-periodic spacing rule. No enhancement of bandwidth resulted from simulations of simple versions of any of the three non-periodic mirrors. However, certain depth-graded structures did exhibit reflectances essentially the same as from uniform mirrors. Moreover, it was found that some control was possible regarding the location (with respect to energy) of the maximum reflectance peak. Effective bandwidth was increased when composite models were simulated. In two of the cases studied, bandwidth was enhanced by a factor of approximately 3. One model consisted of a depth-graded mirror constructed with three separately defined structures, or blocks. Each block consisted of two layer-pairs repeated three times. Then, the entire 18 layer-pair group was repeated several times. Simulation of this 3 block depth-graded configuration yielded three reflectance peaks, one representative of each depth-graded block. The other configurations resulting in enhanced bandwidth assumed independently constructed mirrors immediately adjacent to each other and sharing the same substrate. Reflectance peaks from each mirror appeared in the response. Both basic models show greatly enhanced effective bandwidths even though the reflectance curves appear as non-overlapping for these specific models. Additionally, these configurations are realizable. Details are contained in the section, DESIGN SIMULATIONS.

Kinney, Ralph A.↗
NASA NTRS1994

Evaluation of oxide-coated iridium-rhenium chambers

Iridium-coated rhenium (Ir-Re) provides long life operation of radiation-cooled rockets at temperatures up to 2200 C. Ceramic oxide coatings could be used to increase Ir-Re rocket lifetimes and allow operation in highly oxidizing environments. Ceramic oxide coatings promise to serve as both thermal and diffusion barriers for the iridium layer. Seven ceramic oxide-coated Ir-Re, 22-N rocket chambers were tested with gaseous hydrogen/gaseous oxygen (GHz/G02) propellants. Five chambers had thick (over 10 mils), monolithic coatings of either hafnia (HfO2) or zirconia (ZrO2). Two chambers had coatings with thicknesses less than 5 mils. One of these chambers had a thin-walled coating of ZrO2 infiltrated with sol gel HfO2. The other chamber had a coating composed of an Ir-oxide composite. The purpose of this test program was to assess the ability of the oxide coatings to withstand the thermal shock of combustion initiation, adhere under repeated thermal cycling, and operate in aggressively oxidizing environments. All of the coatings survived the thermal shock of combustion and demonstrated operation at mixture ratios up to 11. Testing the Ir-oxide composite-coated chamber included over 29 min at mixture ratio 16. The thicker walled coatings provided the larger temperature drops across the oxide layer (up to 570 C), but were susceptible to macrocracking and eventual chipping at a stress concentrator. The cracks apparently resealed during firing, under compression of the oxide layer. The thinner walled coatings did not experience the macrocracking and chipping of the chambers that was seen with the thick, monolithic coatings. However, burn-throughs in the throat region did occur in both of the thin-walled chambers at mixture ratios well above stoichiometric. The burn-throughs were probably the result of oxygen diffusion through the oxide coating that allowed the underlying Ir and Re layers to be oxidized. The results of this test program indicated that the thin-walled oxide coatings are better suited for repeated thermal cycling than the thick-walled coating, while thicker coatings may be required for operation in aggressively oxidizing environments.

Reed, Brian D.↗
NASA NTRS1993

Testing and evaluation of oxide-coated iridium/rhenium chambers

Iridium-coated rhenium provides long life operation of radiation-cooled rockets at temperatures up to 2200 C. Ceramic oxide coatings could be used to increase iridium/rhenium rocket lifetimes and allow operation in highly oxidizing environments. Ceramic oxide coatings promise to serve as both thermal and diffusion barriers for the iridium layer. Seven ceramic oxide-coated iridium/rhenium, 22 N rocket chambers were tested on gaseous hydrogen/gaseous oxygen propellants. Five chambers had thick (over 10 mils), monolithic coatings of either hafnia or zirconia. Two chambers had coatings with thicknesses less than 5 mils. One of these chambers had a thin-walled coating of zirconia infiltrated with sol gel hafnia. The other chamber had a coating composed of an iridium/oxide composite. The purpose of this test program was to assess the ability of the oxide coatings to withstand the thermal shock of combustion initiation, adhere under repeated thermal cycling, and operate in aggressively oxidizing environments. All of the coatings survived the thermal shock of combustion and demonstrated operation at mixture ratios up to 11. The iridium/oxide composite coated chamber included testing for over 29 minutes at mixture ratio 16. The thicker-walled coatings provided the larger temperature drops across the oxide layer (up to 570 C), but were susceptible to macrocracking and eventual chipping at a stress concentrator. The cracks apparently resealed during firing, under compression of the oxide layer. The thinner-walled coatings did not experience the macrocracking and chipping of the chambers seen with the thick, monolithic coatings. However, burnthroughs in the throat region did occur in both of the thin-walled chambers at mixture ratios well above stochiometric. The burn-throughs were probably the result of oxygen-diffusion through the oxide coating that allowed the underlying iridium and rhenium layers to be oxidized. The results of this test program indicated that the thin-walled oxide coatings are better suited for repeated thermal cycling than the thick-walled coating, while thicker coatings may be required for operation in aggressively oxidizing environments.

Reed, Brian D.↗
NASA NTRS1994

Low aspect ratio wing experiment

This test was initiated to provide validation data on low aspect ratio wings at transonic speeds. The test was conducted so that the data obtained would be useful in the validation of codes, and all boundary condition data required would be measured as part of the test. During the conduct of the test, the measured quantities were checked for repeatability, and when the data would not repeat, the cause was tracked down and either eliminated or included in the measurement uncertainty. The accuracy of the data was in the end limited by wall imperfections of the wind tunnel in which the test was run.

Olsen, Mike↗
NASA NTRS1995

Space environmental effects on polymer matrix composites as a function of sample location on LDEF

This paper presents results on the effect of circumferential location on the variation in solar absorptance (alpha(sub S)) and infrared emittance (epsilon) for five different polymer matrix composites (PMC), and variations in erosion depth due to atomic oxygen (AO) for fourteen different PMC materials. In addition, a chemical content design parameter (gamma) has been found that correlates well with the erosion yield obtained from space flight data and hyperthermal AO tests for hydrocarbon polymeric materials. This parameter defines the ratio of the total number of atoms in a repeat monomer unit to the difference between the total carbon content and the total number of intermolecular oxygen atoms in the same repeat unit.

Tennyson, R. C.↗
NASA NTRS1995

Spontaneous dewetting of a perfluoropolyether

Eight different production lots of a commercial perfluoropolyether (PFPE) based on hexafluoropropene oxide (HFPO) were applied to polished metal surfaces by spinning. One of the lots repeatedly dewetted from a clean 440C steel surface, forming droplets on the surface, whereas the other seven did not dewet. This dewetting phenomenon also repeatedly occurred on 2024 aluminum and 1018 steel, but not on copper or gold. Fourier transform infrared microspectroscopy (mu-FTIR) was used to determine thickness and uniformity of the PFPE films. The dewetting lot was found to dewet from 440C steel at a film thickness greater than 520 A. A portion of the dewetting lot was heated at 316 C for 12 days in the presence of oxygen and M-50 steel. This fluid did not dewet. Sequentially, samples of the dewetting lot were filtered either with an alumina or a silica cartridge which can remove polar impurities. Neither of the filtered samples dewetted from 440C steel. It was concluded that an unknown impurity, both thermally labile and polar, present at very low concentration and undetected by our analytical techniques (FTIR, proton NMR, or F-19 NMR), was responsible for the dewetting phenomenon.

Shogrin, Bradley↗
NASA NTRS1994

Adaptation of rat soleus muscles to 4 wk of intermittent strain

The effect of repeated strains on rat soleus muscles was investigated by stretching active muscles 3 times/wk for 4 wk with two different methods of stretching. The adaptation of myofibers and noncontractile tissue was followed by histochemical techniques and computer-assisted image analysis. Muscle hypertrophy was seen in the slow-stretched muscles, which increased in mass by 13% and increased in myofiber cross-sectional area by 30%. In the fast-stretched muscle, mass increased by 10% but myofiber cross-sectional area actually decreased. This decrease in mean fiber area was the result of a population of very small fibers (population A) that coexisted with slightly smaller normal-sized fibers (population B). Fibers in population A did not have the distribution expected from atrophy compared with atrophic fibers from unloaded muscles; they were much smaller. In addition, there was a 44% increase in noncontractile tissue in the fast-stretched muscles. Thus, soleus muscles subjected to repeated strains respond differently to slow and fast stretching. Slow stretching results in typical muscle hypertrophy, whereas fast stretching produces somewhat larger muscles but with a mixture of small and normal-sized myofibers accompanied by a marked proliferation of noncontractile tissue.

Stauber, W. T.↗
NASA NTRS1994

Observations of geographically correlated orbit errors for TOPEX/Poseidon using the global positioning system

We have compared Global Positioning System (GPS)-based dynamic and reduced-dynamic TOPEX/Poseidon orbits over three 10-day repeat cycles of the ground-track. The results suggest that the prelaunch joint gravity model (JGM-1) introduces geographically correlated errors (GCEs) which have a strong meridional dependence. The global distribution and magnitude of these GCEs are consistent with a prelaunch covariance analysis, with estimated and predicted global rms error statistics of 2.3 and 2.4 cm rms, respectively. Repeating the analysis with the post-launch joint gravity model (JGM-2) suggests that a portion of the meridional dependence observed in JGM-1 still remains, with global rms error of 1.2 cm.

Christensen, E. J.↗
NASA NTRS1994

Preliminary assessment of the accuracy and precision of TOPEX/POSEIDON altimeter data with respect to the large-scale ocean circulation

TOPEX/POSEIDON sea surface height measurements are examined for quantitative consistency with known elements of the oceanic general circulation and its variability. Project-provided corrections were accepted but are at tested as part of the overall results. The ocean was treated as static over each 10-day repeat cycle and maps constructed of the absolute sea surface topography from simple averages in 2 deg x 2 deg bins. A hybrid geoid model formed from a combination of the recent Joint Gravity Model-2 and the project-provided Ohio State University geoid was used to estimate the absolute topography in each 10-day period. Results are examined in terms of the annual average, seasonal average, seasonal variations, and variations near the repeat period. Conclusion are as follows: the orbit error is now difficult to observe, having been reduced to a level at or below the level of other error sources; the geoid dominates the error budget of the estimates of the absolute topography; the estimated seasonal cycle is consistent with prior estimates; shorter-period variability is dominated on the largest scales by an oscillation near 50 days in spherical harmonics Y(sup m)(sub 1)(theta, lambda) with an amplitude near 10 cm, close to the simplest alias of the M(sub 2) tide. This spectral peak and others visible in the periodograms support the hypothesis that the largest remaining time-dependent errors lie in the tidal models. Though discrepancies attribute to the geoid are within the formal uncertainties of the good estimates, removal of them is urgent for circulation studies. Current gross accuracy of the TOPEX/POSEIDON mission is in the range of 5-10 cm, distributed overbroad band of frequencies and wavenumbers. In finite bands, accuracies approach the 1-cm level, and expected improvements arising from extended mission duration should reduce these numbers by nearly an order of magnitude.

Wunsch, Carl↗
NASA NTRS1994

Application of the GEM-T2 gravity field to altimetric satellite orbit computation

As part of a continuing effort to provide improved orbits for use with existing altimeter data, we have recomputed ephemerides for both the Seasat and Geosat Exact Repeat altimeter missions. The orbits were computed in a consistent fashion, using the Goddard Earth Model T2 (GEM-T2) gravity field along with available ground-based tracking data. Such an approach allows direct comparisons of sea level between the two altimeter systems. Evaluation of the resulting ephemerides indicates that root-mean-square accuracies of 30-50 cm have been achieved for the radial component of the orbits for both satellites. An exception occurs for the last year of the Geosat Exact Repeat Mission, when the rms radial orbit accuracy degrades to the 1-m level at times owing to the inability to adequately model the drag force arising from the increased solar activity.

Haines, Bruce J.↗
NASA NTRS1995

Rapid calibration of seven-hole probes

This paper summarizes the major conclusions and some of the key supporting analyses resulting from the calibration and application of two small seven hole probes at NASA Lewis Research Center. These probes can produce reasonably accurate and rapid surveys of unknown steady flow fields which may include flow angles up to 70 degrees and Mach numbers up to 0.8. The probes were calibrated with both 'complete' and 'reduced' test matrices. Both types of test matrices produced similar results suggesting the the reduced matrices are adequate for most purposes. The average accuracy fo the calibration was about the same as that achieved in previous seven hole probe calibrations. At the higher Mach numbers, the calibration was sensitive to the diameter of the free jet in the calibration facility. Over a narrow angular range at the higher Mach numbers, the system had serious repeatability problems. This lack or repeatability apparently results from aliasing of high frequency (20 to 40 Hz) noise with the data acquisition system sampling frequency of 10 Hz. Analyses show that these noise frequencies are probably not related to airflow dynamics in the connecting tubing.

Ericksen, A. L.↗
NASA NTRS1995

A Fizeau optical interferometer astrometric satellite

The proposed design and construction of the Fizeau astrometric mapping explorer (FAME), a small astrometric instrument for use on an artificial satellite, is reported on. The instrument and spacecraft are designed to slowly spin and will repeatedly scan great circles on the sky so that, over a period of time, it will cover the complete sky and repeat in a manner similar to that of the Hipparcos satellite. The instrument will use the two fixed dilute aperture telescopes to measure a fixed angle between stars and detect the positions, magnitude and color of all stars crossing its field of view to a visual magnitude of approximately 15 mag. The aim of the instrument is to obtain a catalog of positions, proper motions and parallaxes of all stars down to about 15 mag, with a magnitude dependent accuracy of positions of 20 to 800 micro arcsec, proper motions of 20 to 800 micro arcsec per year and parallaxes of 20 to 800 micro arcsec.

Seidelmann, P. Kenneth↗
NASA NTRS1995

The remarkable eclipsing asynchronous AM Herculis binary RX J19402-1025

We report on two years of photometric and spectroscopic observation of the recently discovered AM Herculis star RX J19402-1025. A sharp eclipse feature is present in the optical and X-ray light curves, repeating with a period of 12116.290 +/- 0.003 s. The out-of-eclipse optical waveform contains approximately equal contributions from a signal at the same period and another signal at 12150 s. As these signals drift in and out of phase, the wave form of the light curve changes in a complex but predictable manner. After one entire 'supercycle' of 50 days (the beat period between the shorter periods), the light curve returns to its initial shape. We present long-term ephemerides for each of these periods. It is highly probable that the eclipse period is the underlying orbital period, while the magnetic white dwarf rotates with P = 12150 s. The eclipses appear to be eclipses of the white dwarf by the secondary star. But there is probably also a small obscuring effect from cold gas surrounding the secondary, especially on the orbit-leading side where the stream begins to fall towards the white dwarf. The latter hypothesis can account for several puzzling effects in this star, as well as the tendency among most AM Her stars for the sharp emission-line components to slightly precede the actual motion of the secondary. The presence of eclipses in an asynchronous AM Her star provides a marvelous opportunity to study how changes in the orientation of magnetic field lines affect the accretion flows. Repeated polarimetric light curves and high-resolution studies of the emission lines are now critical to exploit this potential.

Patterson, Joseph↗