Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “performance degradation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
NASA NTRS2017

Mirror coatings for large aperture UV optical infrared telescope optics

Large space telescope concepts such as LUVOIR and HabEx aiming for observations from far UV to near IR require advanced coating technologies to enable efficient gathering of light with important spectral signatures including those in far UV region down to 90nm. Typical Aluminum mirrors protected with MgF2 fall short of the requirements below 120nm. New and improved coatings are sought to protect aluminum from oxidizing readily in normal environment causing severe absorption and reduction of reflectance in the deep UV. Choice of materials and the process of applying coatings present challenges. Here we present the progress achieved to date with experimental investigations of coatings at JPL and at GSFC and discuss the path forward to achieve high reflectance in the spectral region from 90 to 300nm without degrading performance in the visible and NIR regions taking into account durability concerns when the mirrors are exposed to normal laboratory environment as well as high humidity conditions. Reflectivity uniformity required on these mirrors is also discussed.

Quijada, Manuel↗
NASA NTRS2021

NASA Engineering and Safety Center Technical Bulletin No. 21-01: Experimental and Computational Study of Cavitation in Hydrogen Peroxide

Cavitation in liquid propulsion systems can lead to performance degradation and hardware failures. The NESC sponsored an investigation to measure and model cavitation in pressurized hydrogen peroxide fl ow. The experimentally measured and computationally predicted cavitation lengths were compared as a function of cavitation number. The measured and predicted data exhibited close agreement over the range of pressures and temperatures studied, and no calibration of the cavitation model coefficients was needed.

NESC Technical Bulletin No. 21-01↗
NASA NTRS2021

Proton Exchange Membrane Fuel Cell Transient Load Response

Spaceflight mission profiles may not be limited to constant power loads. It is necessary for the associated power system to support changes in load in addition to being energy dense. H2-O2 proton exchange membrane (PEM) fuel cells can accommodate such requirements without significant current smoothing or additional devices to provide transient power. This testing involved current load step changes to characterize non-flow-through PEM fuel cell response to increasing and decreasing load step changes over a range of 0 to 0.5 A/sq. cm. It was determined that fuel cell output voltage stabilizes within 4 ms with no noticeable steady-state performance degradation, following exposure of the fuel cell to transient loads of up to ~1.5 A/sq. cm. Faster stabilization generally occurred following larger step changes.

fuel cell↗
NASA NTRS2021

MODIS Reflective Solar Bands Calibration Improvements for Collection 7

Calibration of Terra and Aqua MODIS reflective solar bands (RSB) has evolved significantly since the launch of the first MODIS instrument on the Terra satellite more than 21 years ago. In NASA’s current Collection 6 and 6.1 Level 1B products (C6/C6.1 L1B), the RSB calibration algorithm continues to rely primarily on the onboard solar diffuser to calibrate the instrument gain. Lunar observations are used to track on-orbit changes in the response versus scan angle (RVS), and data from pseudo-invariant desert sites are used to apply adjustments to the gain and RVS calibration for select bands. The resulting reflectance products have in general shown a very stable performance. In recent years, some performance degradation has been noted for a few bands and algorithm changes have been tested to further improve the calibration accuracy for the upcoming Collection 7 (C7) L1B reprocess. In this paper, we present the MODIS RSB calibration improvements that will be included in C7. Major improvements include: applying polarization correction to the desert data before using it to generateRVS for Terra bands 8, 9, 3, and 10; using ocean scene data and an interband calibration approach to correct for long-term drift of Terra bands 11 and 12; applying an updated crosstalk correction to Terra SWIR bands over the entire mission; and using data from deep convective clouds in Terra SWIR band calibration, including the addition of time-dependent RVS for bands 5 and 26. All other minor calibration changes are also covered. Overall, the reflectance differences at nadir between C6.1 and C7 are within a few percent, though the differences increase in some cases at large scan angles. The Terra visible (3, 8-12) and SWIR bands (5-7, 26) have the most significant improvements. For all other Terra bands and all Aqua bands, the C7-C6.1 differences are mostly within 1%

MODIS↗
NASA NTRS2022

Development and Application of Advanced Measurement Techniques for Characterizing and Controlling Flow Instabilities in Axial Turbomachines

This report summarizes the recent progress in a project aimed at characterizing the flow structure, instabilities, and turbulence in axial compressors, and also on the utilization of casing grooves for delaying the onset of stall without performance degradation at high flow rates. Progress had been hindered by the COVID-19 laboratory closures and restrictions on the number of people that could be present in the laboratory during Fiscal Year 2020. Once the restrictions were lifted, the tasks described in this report were completed.

compressor↗
NASA NTRS2022

Semispan Test Results of a Conventional High-Lift Common Research Model in Landing Configuration

A 10%-scale high-lift version of the Common Research Model (CRM-HL) was tested in the 14- by 22-Foot Subsonic Tunnel at the NASA Langley Research Center. This research was aimed at providing a representative reference case for comparison with an Active Flow Control (AFC) enabled version of the CRM-HL and to increase the existing experimental database for CFD high-lift prediction. The test was conducted mostly at a freestream Mach number of 0.20. The effects of the engine nacelle, nacelle chine, tufts, small variations in Mach number, hysteresis-associated increasing/decreasing angle of attack, and incoming floor boundary-layer thickness (i.e., thinning by activation of the floor boundary layer removal system) were examined. A prestall lift performance degradation for the CRM-HL configuration was resolved with a properly placed nacelle chine. Surface pressure results are presented in detail for three key variants of CRM-HL — baseline (nacelle on), nacelle off, and nacelle with the most effective chine installation. The presented aerodynamic forces and surface pressures include both with and without the wall correction using the Transonic Wall Interference Correction System (TWICS) method. A limited set of photogrammetry results is also presented to document the model deformation under test conditions.

high-lift↗
NASA NTRSDate not supplied

Rapid Cycle Amine 4.0 System Development

Carbon dioxide (CO2) and humidity control is a key function of the spacesuit Portable Life Support Subsystem (PLSS). The latest spacesuit design utilizes a pressure swing bed containing a solid amine sorbent to scrub CO2 and humidity produced by the crewmember from the ventilation loop. The solid amine sorbent removes CO2 and humidity from the ventilation loop through a chemisorption mechanism. Simultaneously, CO2 and humidity are desorbed to vacuum via the two-bed pressure swing system during operation. This continuous regeneration allows for longer Extravehicular Activity (EVA) times while minimizing maintenance, consumables, and power usage. This concept has been in development for over 20 years, during which many prototypes and design iterations have been fabricated and evaluated. This paper discusses the recent Rapid Cycle Amine (RCA) design, development, and testing that has been done to advance the technology. The most recent fabrication is the RCA 3.0. It was delivered to NASA Johnson Space Center in 2015 and has since been tested at the component level and at the integrated PLSS level. The purpose of the component level testing was to understand CO2 removal capacity, end-of-life performance, and establish a baseline performance prior to integrated testing. The RCA 3.0 was integrated into the Exploration Extravehicular Mobility Unit (xEMU) PLSS for a comprehensive Design Verification Test (DVT) series. The integrated testing provided the benefit of characterizing the impact performance degradation has on the system. Many of the RCA requirements were developed through analysis, based on the limitations of the PLSS and, in some cases, assumptions about the system and flow behavior. Integrated testing was an opportunity to validate those requirements and assumptions. While the RCA 3.0 was being tested, the next design iteration, RCA 4.0, was under development. The RCA 4.0 preliminary design phase began in late-2019 and shortly after the Preliminary Design Review, the critical design phase began in 2021. The design work has concluded with the completion of a Pre-Manufacturing Review in 2022. This paper provides an overview of the RCA 4.0 system design, summarizes the results of integrated RCA 3.0 testing, and discusses the pertinence of driving requirements such as mass, volume, and power consumption.

Kelsey Bloom↗
NASA NTRSDate not supplied

Overview of NASA Gateway Lunar Dust Mitigation and Contamination Modeling and Analysis

The planned NASA Artemis campaign has several lunar surface missions in which the NASA Gateway is the waypoint between lunar orbit and the lunar surface for Human Lander System (HLS). Each of these missions is an opportunity for lunar dust to be introduced into the Gateway environment, post surface mission, potentially causing end of life (EOL) performance degradation due to lunar dust contamination of sensitive hardware and systems on the exterior of Gateway and Visiting Vehicles. The Gateway Systems Engineering and Integration (SE&I) and Induced Environments teams are addressing the challenge of lunar dust with a two-pronged approach. Characterization of the lunar dust induced environment around Gateway and contamination risk is accomplished with a comprehensive physics-based framework, the Gateway On-orbit Lunar Dust Modeling and Analysis Program (GOLDMAP), which is currently in development. Analysis results from GOLDMAP define Gateway-level induced environments requirements and are flowed to elements and subsystems. In parallel, a dust mitigation strategy is being developed with a focus on lunar dust protection, dust mitigation technologies, mitigation and testing guidance, and cross-program coordination and is informed by outputs from GOLDMAP analyses. Activities supporting both components include hardware susceptibility assessments and testing, and scientific experiments on lunar regolith.

Gateway↗
NASA NTRSDate not supplied

Real-time Hardware-in-the-Loop Evaluation of a Partially Turboelectric Propulsion Control Design

In support of aviation fuel burn and emission reduction goals, NASA is pursuing high-payoff research investments that promise to transform aviation. This includes investments in Electrified Aircraft Propulsion (EAP). Multiple technology challenges must be addressed to unlock the full potential of EAP. This includes addressing challenges related to propulsion controls, which will be vital for ensuring efficient coordinated operation of EAP subsystems. This paper presents results from real-time hardware-in-the-loop testing of a control design for a single aisle partially-turboelectric aircraft propulsion concept conducted at the NASA Electric Aircraft Testbed (NEAT) facility. The control system under test is designed for a propulsion concept consisting of two wing-mounted turbofan engines that produce thrust and generate electrical power to drive a boundary layer ingesting tailfan propulsor via an electrical motor. An integrated control strategy is applied to ensure coordinated operation of the turbofan and tailfan subsystems during steady-state and transient operation throughout the flight envelope. The NEAT test of this integrated control design consists of a partially hardware-in-the-loop, partially simulated configuration. A subscale representation of the electrical system design is implemented in hardware and mechanically coupled to electric machines that emulate turbomachinery and propulsor shaft dynamics. The hardware configuration is then operated under the control of a real-time computer application that runs a simulation of the propulsion system and the developed control logic. The NEAT facility test campaign includes a series of experiments that subject the control design to throttle transients conducted throughout the flight envelope and full-flight mission profiles. Testing under simulated performance degradation is also conducted to evaluate control design robustness. This includes constant and abrupt changes in degradation levels. Results from the hardware-in-the-loop test are presented and shown to be in good agreement with pre-test simulation predictions demonstrating the efficacy of the integrated control design approach.

Electrified Aircraft Propulsion↗
NASA NTRSDate not supplied

Real-time Hardware-in-the-Loop Evaluation of a Partially Turboelectric Propulsion Control Design

In support of aviation fuel burn and emission reduction goals, NASA is pursuing high-payoff research investments that promise to transform aviation. This includes investments in Electrified Aircraft Propulsion (EAP). Multiple technology challenges must be addressed to unlock the full potential of EAP. This includes addressing challenges related to propulsion controls, which will be vital for ensuring efficient coordinated operation of EAP subsystems. This paper presents results from real-time hardware-in-the-loop testing of a control design for a single aisle partially-turboelectric aircraft propulsion concept conducted at the NASA Electric Aircraft Testbed (NEAT) facility. The control system under test is designed for a propulsion concept consisting of two wing-mounted turbofan engines that produce thrust and generate electrical power to drive a boundary layer ingesting tailfan propulsor via an electrical motor. An integrated control strategy is applied to ensure coordinated operation of the turbofan and tailfan subsystems during steady-state and transient operation throughout the flight envelope. The NEAT test of this integrated control design consists of a partially hardware-in-the-loop, partially simulated configuration. A subscale representation of the electrical system design is implemented in hardware and mechanically coupled to electric machines that emulate turbomachinery and propulsor shaft dynamics. The hardware configuration is then operated under the control of a real-time computer application that runs a simulation of the propulsion system and the developed control logic. The NEAT facility test campaign includes a series of experiments that subject the control design to throttle transients conducted throughout the flight envelope and full-flight mission profiles. Testing under simulated performance degradation is also conducted to evaluate control design robustness. This includes constant and abrupt changes in degradation levels. Results from the hardware-in-the-loop test are presented and shown to be in good agreement with pre-test simulation predictions demonstrating the efficacy of the integrated control design approach.

Electrified Aircraft Propulsion↗
NASA NTRS2023

Real-Time Hardware-in-the-Loop Evaluation of A Partially Turboelectric Propulsion Control Design

In support of aviation fuel burn and emission reduction goals, NASA is pursuing high-payoff research investments that promise to transform aviation. This includes investments in Electrified Aircraft Propulsion (EAP). Multiple technology challenges must be addressed to unlock the full potential of EAP. This includes addressing challenges related to propulsion controls, which will be vital for ensuring efficient coordinated operation of EAP subsystems. This paper presents results from real-time hardware-in-theloop (HIL) testing of a control design for a single aisle partially-turboelectric aircraft propulsion concept conducted at the NASA Electric Aircraft Testbed (NEAT) facility. The control system under test is designed for a propulsion concept consisting of two wing-mounted turbofan engines that produce thrust and generate electrical power to drive a boundary layer ingesting tailfan propulsor via an electrical motor. An integrated control strategy is applied to ensure coordinated operation of the turbofan and tailfan subsystems during steady-state and transient operation throughout the flight envelope. The NEAT test of this integrated control design consists of a partially HIL, partially simulated configuration. A subscale representation of the electrical system design is implemented in hardware and mechanically coupled to electric machines that emulate turbomachinery and propulsor shaft dynamics. The hardware configuration is then operated under the control of a real-time computer application that runs a simulation of the propulsion system and the developed control logic. The NEAT facility test campaign includes a series of experiments that subject the control design to throttle transients conducted throughout the flight envelope and full-flight mission profiles. Testing under simulated performance degradation is also conducted to evaluate control design robustness. This includes constant and abrupt changes in degradation levels. Results from the HIL test are presented and shown to be in good agreement with pretest simulation predictions demonstrating the efficacy of the integrated control design approach.

Electrified Aircraft Propulsion↗
NASA NTRSDate not supplied

Robust Path-following Controller for Multirotor Vehicles in Uncertain Wind Conditions

This paper presents simulations of L1 adaptive controller on a multirotor vehicle for compensation of convective winds. There are increasing efforts to utilize unmanned vehicles for fighting wildfires, but such vehicles need to be able to compensate for convective updrafts and other uncertainties (e.g., wind shear and turbulence) caused by the wildfire. Other application domains, such as urban air mobility, also must account for convective or uncertain winds present in urban microclimates. Geometric controllers have great tracking performance properties in environments without uncertainties, but the tracking performance degrades when wind disturbances and external loads are present in the environment. Introducing L1 adaptive control into the controller architecture compensates for these wind disturbances and reduces the tracking error caused by such disturbances. The controller architecture is implemented on a small quadrotor. The simulations demonstrate the advantages of the L1 adaptive augmentation for a sample figure-eight trajectory while encountering unknown variable wind conditions with an external load.

John L Bullock↗
NASA NTRSDate not supplied

Robust Path-following Controller for Multirotor Vehicles in Uncertain Wind Conditions

This paper presents simulations of L1 adaptive controller on a multirotor vehicle for compensation of convective winds. There are increasing efforts to utilize unmanned vehicles for fighting wildfires, but such vehicles need to be able to compensate for convective updrafts and other uncertainties (e.g., wind shear and turbulence) caused by the wildfire. Other application domains, such as urban air mobility, also must account for convective or uncertain winds present in urban microclimates. Geometric controllers have great tracking performance properties in environments without uncertainties, but the tracking performance degrades when wind disturbances and external loads are present in the environment. Introducing L1 adaptive control into the controller architecture compensates for these wind disturbances and reduces the tracking error caused by such disturbances. The controller architecture is implemented on a small quadrotor. The simulations demonstrate the advantages of the L1 adaptive augmentation for a sample figure-eight trajectory while encountering unknown variable wind conditions with an external load.

John Bullock↗
NASA NTRSDate not supplied

Abrasive Effects of Lunar Regolith on Material Wear for Long-Term Lunar Applications

Long-term operations on the Moon’s surface require materials that can withstand the harsh lunar environment. Lunar dust and regolith pose significant threats to the long-term durability of materials used in lunar applications. Lunar dust, easily perturbed and dispersed, adheres and abrades materials due to its rough and irregular grain morphology. More closely representing this abrasion action through experimental laboratory testing is critical in assessing the durability of potential lunar candidate materials used in mechanical, sensor, and human-based systems. In this study, the performance of materials using Taber abrasive wheels made from lunar regolith simulant was assessed and compared to results obtained using standard ceramic-based abrasion materials. The results highlight a difference in the abrasive wear rates between the lunar regolith simulant and the standard ceramic-based abrasive. Utilizing the mechanisms and testing capabilities of this two-body abrasive interaction leveraging regolith-based abrasives may more closely represent the interplay between materials and lunar dust, which is vital for assessing the long-term viability of materials for extended lunar missions. Improved lunar testing capabilities may also enhance evaluations of the long-term performance degradation of passive and active dust mitigation methods.

Zachary Stein↗
NASA NTRS1984

A performability solution method for degradable nonrepairable systems

The present performability model-solving algorithm identifies performance with 'reward', representing the state behavior of a system S by a finite-state stochastic process and determining reward by means of reward rates that are associated with the states of the base model. A general method is obtained for determining the probability distribution function of the performance (reward) variable, and therefore the performability, of the corresponding system. This is done for bounded utilization periods, and the result is an integral expression which is either analytically or numerically solvable.

Furchtgott, D. G.↗
NASA NTRS1998

Active Pattern Factor Control for Gas Turbine Engines

Small variations in fuel/air mixture ratios within gas turbine combustors can result in measurable, and potentially detrimental, exit thermal gradients. Thermal gradients can increase emissions, as well as shorten the design life of downstream turbomachinery, particularly stator vanes. Uniform temperature profiles are usually sought through careful design and manufacturing of related combustor components. However, small componentto-component variations as well as numerous aging effects degrade system performance. To compensate for degraded thermal performance, researchers are investigating active, closed-loop control schemes.

May, James E.↗
NASA NTRS1981

Coding tradeoffs for improved performance of FH/MFSK systems in partial band noise

Partial band noise jamming can severely degrade the performance of frequency-hopped, M-ary frequency-shift keyed communciation systems. This paper illustrates the tradeoffs between channel coding, diversity, and block orthogonal (MFSK) modulation as a means of overcoming the advantage of worst case, non-adaptive (as opposed to repeat-back) partial band jamming. For ease of computation, the analysis relies on exponentially tight error bounds, and is based on a noncoherent detection metric that requires jamming state information for each hop. A more robust, less complex receiver structure which eliminates the jamming knowledge requirement is shown to degrade performance less than 2-1/2 dB. The coding tradeoffs discussed in this report are exemplified in the design of a hypothetical 32 kb/s military frequency-hopped communication link.

Levitt, B. K.↗