Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “oscillating flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Inhomogeneity of pulmonary perfusion during sustained microgravity

The effects of gravity on the inhomogeneity of pulmonary perfusion in man were studied by performing hyperventilation-breathhold single-breath measurements before, during and after 9 days of continuous exposure to microgravity. In microgravity the indicators of inhomogeneity of perfusion, especially the size of cardiogenic oscillations in expired CO2 and the height of phase 4, were both markedly reduced. Cardiogenic oscillations were reduced to approximately 60 of their preflight standing size, while the height of phase 4 was between 0 and -8% (a terminal fall became a small terminal rise) of preflights standing. The terminal change in CO2 was nearly abolished in microgravity indicating more uniformity of blood flow between lung units that close at the end of expiration and units that remain open. This may result from the disappearance of gravity-dependent topographical inequality of blood flow. The residual cardiographic oscillations in expired CO2 imply a persisting inhomogeneity of perfusion in the absence of gravity at a level larger than acinar.

Prisk, G. Kim↗
NASA NTRS1978

Water-tunnel experiments on an oscillating airfoil at RE equals 21,000

Flow visualization experiments were performed in a water tunnel on a modified NACA 0012 airfoil undergoing large amplitude harmonic oscillations in pitch. Hydrogen bubbles were used to: (1) create a conveniently striated and well preserved set of inviscid flow markers; and (2) to expose the succession of events occurring within the viscous domain during the onset of dynamic stall. Unsteady effects were shown to have an important influence on the progression of flow reversal along the airfoil surface prior to stall. A region of reversed flow underlying a free shear layer was found to momentarily exist over the entire upper surface without any appreciable disturbance of the viscous-inviscid boundary. A flow protuberance was observed to develop near the leading edge, while minor vortices evolve from an expanding instability of the free shear layer over the rear portion of the airfoil. The complete breakdown of this shear layer culminates in the successive formation of two dominant vortices.

Mcalister, K. W.↗
NASA NTRS1994

Inhomogeneity of pulmonary perfusion during sustained microgravity on SLS-1

We studied the effects of gravity on the inhomogeneity of pulmonary perfusion in humans by performing hyperventilation-breath-hold single-breath measurements before, during, and after 9 days of continuous exposure to microgravity during the Spacelab Life Sciences-1 (SLS-1) mission. In microgravity the indicators of inhomogeneity of perfusion, especially the size of cardiogenic oscillations in expired CO2 and the height of phase IV, were markedly reduced. Cardiogenic oscillations were reduced to approximately 60% of their preflight standing size, and the height of phase IV was between 0 and -8% (a terminal fall became a small terminal rise) of the preflight standing value. The terminal change in expired CO2 was nearly abolished in microgravity, indicating more uniformity of blood flow between lung units that close and those that remain open at the end of expiration. A possible explanation of this observation is the disappearance of gravity-dependent topographic inequality of blood flow. The residual cardiogenic oscillations in expired CO2 imply a persisting inhomogeneity of perfusion in the absence of gravity, probably in lung regions that are not within the same acinus.

Prisk, G. Kim↗
NASA NTRS2000

Quantifying Instability Sources in Liquid Rocket Engines

Computational fluid dynamics methodology to predict the effects of combusting flows on acoustic pressure oscillations in liquid rocket engines (LREs) is under development. 'Me intent of the investigation is to develop the causal physics of combustion driven acoustic resonances in LREs. The crux of the analysis is the accurate simulation of pressure/density/sound speed in a combustor which when used by the FDNS-RFV CFD code will produce realistic flow phenomena. An analysis of a gas generator considered for the Fastrac engine will be used as a test validation case.

Farmer, Richard C.↗
NASA NTRS1942

The stability of laminar flow past a sphere

As a contribution to the problem of turbulence on a surface of rotation, the method of small oscillation is applied to the flow past a sphere. It was found that the method developed for two-dimensional flow is applicable without modifications. The frictional layer in the vicinity of the stagnation point of a surface of rotation is less stable against small two-dimensional disturbances than in the stagnation point itself, as proved from an analysis of the velocity distribution made by Homann.

Pretsch, J↗
NASA NTRS1988

The effects of compressibility on dynamic stall

In this paper, typical computational predictions and experimental measurements of compressible flow past an airfoil at dynamic stall conditions are studied and compared to develop an insight into the effect of compressibility on dynamic stall. The dependency of the critical Mach number on airfoil leading edge curvature, camber, and angle of attack is investigated. Evidence is presented to show that a local region of supersonic flow occurs on an oscillating airfoil, even for a freestream Mach number as low as 0.2, if the boundary layer remains attached and the angle of attack is sufficiently high; that a shock terminates this local supersonic bubble; and that the vorticity that this shock generates grows rapidly and becomes very unstable as the angle of attack increases beyond the value at which the maximum local flow speed first exceeds the speed of sound. It is suggested that these shock-induced effects compete with the dynamic viscous effects occurring in the boundary layer in determining the onset of separation, which can lead to premature dynamic stall and can significantly reduce the maximum dynamic lift that can otherwise be obtained.

Fung, K.-Y.↗
NASA NTRS2011

Steady and Unsteady Flow Effects of Circumferential Grooves Casing Treatment in a Transonic Compressor Rotor

The current paper reports on an investigation of steady and unsteady flow effects of circumferential grooves casing treatment in a transonic compressor rotor. Circumferential grooves casing treatment is used mainly to increase stall margin in axial compressors with a relatively small decrease in aerodynamic efficiency. It is widely believed that flow mechanisms of circumferential grooves casing treatment near stall conditions are not yet well understood even though this treatment has been used widely in real engines. Numerical analysis based on steady Reynolds-averaged Navier-Stokes (RANS) has been the primary tool used to understand flow mechanism for circumferential grooves casing treatment. Although steady RANS explains some flow effects of circumferential grooves casing treatment, it does not calculate all the measured changes in the compressor characteristics. Therefore, design optimization of circumferential grooves with steady RANS has not been very successful. As a compressor operates toward the stall condition, the flow field becomes transient. Major sources of self-generated flow unsteadiness are shock oscillation and interaction between the passage shock and the tip leakage vortex. In the present paper, an unsteady Reynolds-averaged Navier-Stokes (URANS) approach is applied to study the effects of circumferential grooves in a transonic compressor. The results from URANS are compared with the results from RANS and measured data. The current investigation shows that there are significant unsteady flow effects on the performance of the circumferential grooves casing treatment. For the currently investigated rotor, the unsteady effects are of the same magnitude as the steady effects in terms of extending the compressor stall margin.

Hah, Chunill↗
NASA NTRS2023

Effects of Heating Configuration and Operating Parameters on Heat Transfer and Interfacial Physics of Microgravity Flow Boiling With Subcooled Inlet Conditions –Experiments Onboard the International Space Station

This study is part of the Flow Boiling and Condensation Experiment (FBCE), a collaborative effort between the Purdue University Boiling and Two-Phase Flow Laboratory (PU-BTPFL) and the NASA Glenn Research Center. The FBCE fitted with the Flow Boiling Module (FBM) was launched to the International Space Station (ISS) in August 2021 and experiments were successfully performed from February to July 2022 to amass a large microgravity-flow-boiling database. This study is focused on heat transfer and flow visualization of microgravity flow boiling of n-Perfluorohexane in a rectangular channel of 5.0 mm height, 2.5 mm width (heated), and 114.6 mm length, with subcooled inlet conditions. High-speed-video photography is utilized to present flow patterns and temporal interfacial behavior. Heat transfer results are presented in the form of flow boiling curves and both parametric curves and streamwise profiles of wall temperature and heat transfer coefficient. Firstly, the parametric effects of mass velocity (199.4 – 3200.0 kg/m 2 s), inlet subcooling (0.2 – 46.0°C), and inlet pressure (124.2 – 176.7 kPa), on the aforementioned aspects are assessed for double-sided heating to establish them for a microgravity environment. Of these three parameters, mass velocity and inlet subcooling mostly determine the microgravity flow boiling behavior, while inlet pressure plays an insignificant role. Flow patterns for double-sided heating are more complex than those for single-sided heating due to interaction between the two vapor layers. Vapor interaction is minimized at high subcoolings and high mass velocities due to strong condensation offered by the subcooled bulk liquid layer separating them. Despite the different flow patterns, both single- and double-sided heating generally result in similar parametric trends and local heat transfer coefficients for similar operating conditions. Flow instabilities manifest as temporal flow anomalies and temperature oscillations, and their severity increases with increasing boiling number. Secondly, the effects of heating configuration are analyzed by comparing and contrasting several aspects of single- and double-sided heating data. The heat fluxes at which onset of nucleate boiling degradation (ONBD) and critical heat flux (CHF) occur are distinctly different for single- and double-sided heating. There exists a threshold inlet subcooling demarcating the dominance of flow acceleration and condensation effects in vapor removal from the near-wall region and replenishment of fresh liquid for boiling. Above the threshold, condensation from the near-wall region is dominant and single-sided heating yields higher heat fluxes, and below it, acceleration is dominant and double-sided yields higher heat fluxes. At mass velocity in the range of 200 – 2400 kg/m 2 s, the threshold inlet subcooling lies in the approximate range of 20 – 30°C (corresponding inlet quality of roughly -0.40 – -0.20).

Microgravity↗
NASA NTRS1946

Flutter and oscillating air-force calculations for an airfoil in two-dimensional supersonic flow

A connected account is given of the Possio theory of non-stationary flow for small disturbances in a two-dimensional supersonic flow and of its application to the determination of the aerodynamic forces on an oscillating airfoil. Further application is made to the problem of wing flutter in the degrees of freedom - torsion, bending, and aileron rotations. Numerical tables for flutter calculations are provided for various values of the Mach number greater than unity. Results for bending-torsion wing flutter are shown in figures and are discussed. The static instabilities of divergence and aileron reversal are examined as is a one-degree-of-freedom case of torsional oscillatory instability.

Garrick, I E↗
NASA NTRS2002

A Solar Model with g-Modes

Good evidence is assembled showing that the Suit's core arid surface vary on time scales from a month to a decade arid that a number of scales are similar. The most plausible source for numerous long time scales and periodicities is long-lived global oscillations. This suggests g-modes (oscillations restored mainly by buoyancy) because they particularly affect the core and base of the convective envelope, which then indirectly modulates the surface. Also, standing g-modes have rotational properties that match many observed periodicities. But the standard solar model (SSM) has a static core and excites few if any g-modes. making new interior structures worth exploring. The model outlined here assumes two well mixed shells near 0.18 and 0.68 R, (13 = solar radius) where sound speed data shows sharp deviations from the SSM. Mixing is sustained by flows driven by the oscillations. The shells form a cavity that excludes g-modes from their main damping region below 0.1 R, assisting their net excitation and increasing their oscillation periods by at least a factor of two and probably much more. In terms of the solar luminosity L, the modes transport up through the cavity a power approx. 0.004 L as a lower limit and 0.11 L as all upper limit. The modes dissipate energy in the outer shell and cool the inner shell, asymmetrically in each case, and this stimulates occasional convective events whose response time is typically 0.8 years longer near the inner shell. Such events cool the core and reduce neutrino flux while heating the envelope and increasing solar activity. This gives a physical basis for a well mixed Sun with low neutrino flux and basis for the observed anticorrelation and lag of neutrino behind surface activity.

Wolff, Charles L.↗
NASA NTRS1981

Some features of unsteady separating turbulent boundary layers

The physical features of steady and unsteady separating turbulent boundary layers are discussed with reference to wind-tunnel data obtained at a Reynolds number of 5.1 x 10 to the 6th and a reduced frequency of 0.55. It is shown that a moderate-amplitude (R less than 0.3) oscillating turbulent boundary layer has a mean flow structure that is close to that of a steady free-stream turbulent boundary layer. Well upstream of the separation, unexpected phase shifts of the velocity and turbulence oscillations occur near the wall between the viscous sublayer and the semilogarithmic region. Significant phase variations between the velocity and turbulence also exist in the detached and back flows downstream. Large amplitude oscillations are shown to have a substantial effect on the flow structure.

Simpson, R. L.↗
NASA NTRS1983

Calculation of boundary layers near the stagnation point of an oscillating airfoil

The results of an investigation of boundary layers close to the stagnation point of an oscillating airfoil are reported. Two procedures for generating initial conditions, the characteristics box scheme and a quasi-static approach, were investigated, and the quasi-static approach was shown to be appropriate provided the initial region was far from any flow separation. With initial conditions generated in this way, the unsteady boundary layer equations were solved for the flow in the leading edge region of a NACA 0012 airfoil oscillating from 0 to 5 deg. Results were obtained for both laminar and turbulent flow, and, in the latter case, the effect of transition was assessed by specifying its occurrence at different locations. The results demonstrate the validity of the numerical scheme and suggest that the procedures should be applied to calculation of the entire flow around oscillating airfoils.

Cebeci, T.↗
NASA NTRS1996

Forced Rolling Oscillation of a 65 deg-Delta Wing in Transonic Vortex-Breakdown Flow

Unsteady, transonic, vortex dominated flow over a 65 deg. sharp-edged, cropped-delta wing of zero thickness undergoing forced rolling oscillations is investigated computationally. The wing angle of attack is 20 deg. and the free stream Mach number and Reynolds number are 0.85 and 3.23 x 10(exp 6), respectively. The initial condition of the flow is characterized by a transverse terminating shock which induces vortex breakdown of the leading edge vortex cores. The computational investigation uses the time accurate solution of the laminar, unsteady, compressible, full Navier-Stokes equations with the implicit, upwind, Roe flux difference splitting, finite-volume scheme. While the maximum roll amplitude is kept constant at 4.0 deg., both Reynolds number and roll frequency are varied covering three cases of forced sinusoidal rolling. First, the Reynolds number is held at 3.23 x 10(exp 6) and the wing is forced to oscillate in roll around the axis of geometric symmetry at a reduced frequency of 2(pi). Second, the Reynolds number is reduced to 0.5 x 10(exp 6) to observe the effects of added viscosity on the vortex breakdown. Third, with the Reynolds number held at 0.5 x 10(exp 6), the roll frequency is reduced to 1(pi) to complete the study.

Menzies, Margaret A.↗
NASA NTRS1993

Viscous/Inviscid Interaction On An Oscillating Airfoil

Viscous/inviscid-interaction procedure developed for computation of two-dimensional flow of air about airfoil, angle of attack of which oscillates at high amplitude. Purpose of procedure to study flow effects in dynamic stall. Bulk of flow treated as inviscid, while effects of viscosity treated only on surface of airfoil and in boundary layer. Inviscid part of flow simulated via time-marching, unsteady-subsonic-flow panel method incorporating appropriate distributions of unsteady surface and wake singularities.

Carr, L. W.↗
NASA NTRS1961

Unsteady Aerodynamic Forces on a Slender Body of Revolution in Supersonic Flow

Linearized slender-body theory is applied to the computation of aerodynamic forces on an oscillating, or deforming, body in supersonic flow. The undeformed body is a body of revolution and the deformed body is represented by movement of a line through the centers of the cross sections which are assumed to remain circular. The time dependence is based on sinusoidal motion. For a body of vanishing thickness the slender-body theory yields the apparent mass approximation as it is obtained for incompressible crossflow around a cylinder. Both linearized slender-body theory and the apparent mass approximation are used to calculate the pitching-moment coefficients on a rigid slender body with a parabolic arc nose cone, and these coefficients are compared with some experimental results.

Bond, Reuben↗
NASA NTRS1946

Flutter and oscillating air-force calculations for an airfoil in a two-dimensional supersonic flow

An account is given of the Possio theory of non stationary flow for small disturbances in a two-dimensional supersonic flow and of its application to determination of the aerodynamic forces on an oscillating airfoil. Further application is made to the problem of wing flutter in the degrees of freedom - torsion, bending, and aileron torsion. Numerical tables for flutter calculations are provided for numerous values of the Mach number greater than unity. Results for bending-torsion wing flutter are discussed. The static instabilities of divergence and aileron reversal are examined as is a one degree of freedom case of torsional oscillatory instability.

Garrick, I E↗
NASA NTRS1996

An Experimental Device for Generating High Frequency Perturbations in Supersonic Wind Tunnels

This paper describes the analytical study of a device that has been proposed as a mechanism for generating gust-like perturbations in supersonic wind tunnels. The device is envisioned as a means to experimentally validate dynamic models and control systems designed for high-speed inlets. The proposed gust generator is composed of two flat trapezoidal plates that modify the properties of the flow ingested by the inlet. One plate may be oscillated to generate small perturbations in the flow. The other plate is held stationary to maintain a constant angle-of-attack. Using an idealized approach, design equations and performance maps for the new device were developed from the compressible flow relations. A two-dimensional CFD code was used to confirm the correctness of these results. The idealized approach was then used to design and evaluate a new gust generator for a 3.05-meter by 3.05-meter (10-foot by 10-foot) supersonic wind tunnel.

Melcher, Kevin J.↗