Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “numerical optimal control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
NASA NTRS2018

Transition Delay via Vortex Generators in a Hypersonic Boundary Layer at Flight Conditions

The potential of realizable, stationary streaks undergoing non-modal growth to stabilize a hypersonic boundary-layer flow and, subsequently, delay the laminar-turbulent transition onset, is studied via numerical computations. The geometry and flow conditions are selected to match a relevant trajectory location from the ascent phase of the HIFiRE-1 flight experiment, namely, a 7-degree half-angle cone with 2.5 mm nose radius, freestream Mach number of 5.30, freestream unit Reynolds number equal to 13.42 x 10(exp 6)/m, and wall-to-adiabatic temperature ratio of approximately 0.35 over most of the test article. This paper investigates flow modifications induced by wall-mounted vortex generators (VGs), followed by an analysis of the modal instability of the perturbed, streaky boundary-layer flow. Results are presented both for a single array of VGs that was designed on the basis of optimal growth theory and for a VG configuration involving two separate arrays with opposite orientations that ware designed to provide staged control of flow instabilities while simultaneously reducing the amplification of streak instabilities resulting from the control devices. Earlier research had shown that the onset of transition during the HIFiRE-1 flight experiment, which did not include any control devices, correlated with an amplification factor of N = 14.7 for the planar Mack modes. If one assumes that the transition N -factor is not affected by the introduction of the VGs, then the control configurations based on a single array of VGs and two separate arrays would result in a transition delay of 17% and 40%, respectively. These findings suggest a passive flow control s to induce streaks that would delay transition in hypersonic boundary dominated by Mack-mode instabilities.

Incompressible boundary layer↗
NASA NTRS2020

Pterodactyl: The Development and Performance of Guidance Algorithms for a Mechanically Deployed Entry Vehicle

Pterodactyl is a NASA Space Technology Mission Directorate (STMD) project focused on developing a design capabilityfor optimal, scalable, Guidance and Control (G&C) solutions that enable precision targeting for Deployable Entry Vehicles(DEVs). This feasibility study is unique in that it focuses on the rapid integration of targeting performance analysis withstructural &packaging analysis, which is especially challenging for new vehicle and mission designs. This paper will detailthe guidance development and trajectory design process for a lunar return mission, selected to stress the vehicle designsand encourage future scalability. For the five G&C configurations considered, the Fully Numerical Predictor-CorrectorEntry Guidance (FNPEG) was selected for configurations requiring bank angle guidance and FNPEG with Uncoupled

Johnson, Breanna↗
NASA NTRS1993

A numerical approach to controller design for the ACES facility

In recent years the employment of active control techniques for improving the performance of systems involving highly flexible structures has become a topic of considerable research interest. Most of these systems are quite complicated, using multiple actuators and sensors, and possessing high order models. The majority of analytical controller synthesis procedures capable of handling multivariable systems in a systematic way require considerable insight into the underlying mathematical theory to achieve a successful design. This insight is needed in selecting the proper weighting matrices or weighting functions to cast what is naturally a multiple constraint satisfaction problem into an unconstrained optimization problem. Although designers possessing considerable experience with these techniques have a feel for the proper choice of weights, others may spend a significant amount of time attempting to find an acceptable solution. Another disadvantage of such procedures is that the resulting controller has an order greater than or equal to that of the model used for the design. Of course, the order of these controllers can often be reduced, but again this requires a good understanding of the theory involved.

Frazier, W. Garth↗
NASA NTRS1972

The optimal control of merging aircraft - Implementation of the hybrid air traffic controller.

The control of merging aircraft is formulated as a finite-time, quadratic optimal control problem of a linear system with state and control constraints. The purpose of this paper is to demonstrate that the Hybrid Air Traffic Controller (HAC), which has been previously developed as a solution to this problem, may be easily implemented. Use is made of both the properties of the algebraic solution to the matrix Riccati equation and the structure of the linear model. This approach results in a real-time synthesis procedure for the HAC which does not rely on iterative numerical integration techniques.

Schatz, J. G.↗
NASA NTRS2003

Lorentz Body Force Induced by Traveling Magnetic Fields

The Lorentz force induced by a traveling magnetic field (TMF) in a cylindrical container has been calculated. The force can be used to control flow in dectrically conducting melts and the direction of the magnetic field and resulting flow can be reversed. A TMF can be used to partially cancel flow driven by buoyancy. The penetration of the field into the cylinder decreases as the frequency increases, and there exists an optimal value of frequency for which the resulting force is a maximum. Expressions for the Lorentz force in the limiting cases of low frequency and infinite cylinder are also given and compared to the numerical calculations.

Volz, M. P.↗
NASA NTRS2005

Central-Monitor Software Module

One of the software modules of the emergency-vehicle traffic-light-preemption system of the two preceding articles performs numerous functions for the central monitoring subsystem. This module monitors the states of all units (vehicle transponders and intersection controllers): It provides real-time access to the phases of traffic and pedestrian lights, and maps the positions and states of all emergency vehicles. Most of this module is used for installation and configuration of units as they are added to the system. The module logs all activity in the system, thereby providing information that can be analyzed to minimize response times and optimize response strategies. The module can be used from any location within communication range of the system; with proper configuration, it can also be used via the Internet. It can be integrated into call-response centers, where it can be used for alerting emergency vehicles and managing their responses to specific incidents. A variety of utility subprograms provide access to any or all units for purposes of monitoring, testing, and modification. Included are "sniffer" utility subprograms that monitor incoming and outgoing data for accuracy and timeliness, and that quickly and autonomously shut off malfunctioning vehicle or intersection units.

Bachelder, Aaron↗
NASA NTRS2012

SCaN Testbed Software Development and Lessons Learned

National Aeronautics and Space Administration (NASA) has developed an on-orbit, adaptable, Software Defined Radio (SDR)Space Telecommunications Radio System (STRS)-based testbed facility to conduct a suite of experiments to advance technologies, reduce risk, and enable future mission capabilities on the International Space Station (ISS). The SCAN Testbed Project will provide NASA, industry, other Government agencies, and academic partners the opportunity to develop and field communications, navigation, and networking technologies in the laboratory and space environment based on reconfigurable, SDR platforms and the STRS Architecture.The SDRs are a new technology for NASA, and the support infrastructure they require is different from legacy, fixed function radios. SDRs offer the ability to reconfigure on-orbit communications by changing software for new waveforms and operating systems to enable new capabilities or fix any anomalies, which was not a previous option. They are not stand alone devices, but required a new approach to effectively control them and flow data. This requires extensive software to be developed to utilize the full potential of these reconfigurable platforms. The paper focuses on development, integration and testing as related to the avionics processor system, and the software required to command, control, monitor, and interact with the SDRs, as well as the other communication payload elements. An extensive effort was required to develop the flight software and meet the NASA requirements for software quality and safety. The flight avionics must be radiation tolerant, and these processors have limited capability in comparison to terrestrial counterparts. A big challenge was that there are three SDRs onboard, and interfacing with multiple SDRs simultaneously complicatesd the effort. The effort also includes ground software, which is a key element for both the command of the payload, and displaying data created by the payload. The verification of the software was an extensive effort. The challenges of specifying a suitable test matrix with reconfigurable systems that offer numerous configurations is highlighted. Since the flight system testing requires methodical, controlled testing that limits risk, a nearly identical ground system to the on-orbit flight system was required to develop the software and write verification procedures before it was installed and tested on the flight system. The development of the SCAN testbed was an accelerated effort to meet launch constraints, and this paper discusses tradeoffs made to balance needed software functionality and still maintain the schedule. Future upgrades are discussed that optimize the avionics and allow experimenters to utilize the SCAN testbed potential.

radio communication↗
NASA NTRS2020

Pterodactyl: The Development and Performance of Guidance Algorithms for a Mechanically Deployed Entry Vehicle

Pterodactyl is a NASA Space Technology Mission Directorate (STMD) project focused on developing a design capability for optimal, scalable, Guidance and Control (G&C) solutions that enable precision targeting for Deployable Entry Vehicles (DEVs). This feasibility study is unique in that it focuses on the rapid integration of targeting performance analysis with structural & packaging analysis, which is especially challenging for new vehicle and mission designs. This paper will detail the guidance development and trajectory design process for a lunar return mission, selected to stress the vehicle designs and encourage future scalability. For the five G&C configurations considered, the Fully Numerical Predictor-Corrector Entry Guidance (FNPEG) was selected for configurations requiring bank angle guidance and FNPEG with Uncoupled Range Control (URC) was developed for configurations requiring angle of attack and sideslip angle guidance. Successful G&C configurations are defined as those that can deliver payloads to the intended descent and landing initiation point, while abiding by trajectory constraints for nominal and dispersed trajectories.

Johnson, Breanna J.↗
NASA NTRS1982

Heat flow control and segregation in directional solidification

Optimization of the vertical Bridgman technique for growth of electronic materials in single crystal form was investigated. The limitations of the crystal growth configuration were experimentally determined and heat transfer related deficiencies identified. Design of an alternate system was based on the use of heat pipes separated by a gradient region. Heat transfer analyses based on one and two dimensional models indicated the necessity of a flexible gradient zone configuration. Directional melting of binary systems as encountered during seeding in melt growth was analysed for concurrent compositional changes at the crystal-metal interface, and the theoretical treatment numerically applied to HgCdTe and Ga doped germanium. A theoretical and experimental study of the thermal effects associated with current flow was conducted. It was found that experimental measurements of dc induced growth during crystal pulling can be used for the precise determination of the Peltier coefficient.

Witt, A. F.↗
NASA NTRS1988

Research on output feedback control

A summary is presented of the main results obtained during the course of research on output feedback control. The term output feedback is used to denote a controller design approach which does not rely on an observer to estimate the states of the system. Thus, the order of the controller is fixed, and can even be zero order, which amounts to constant gain ouput feedback. The emphasis has been on optimal output feedback. That is, a fixed order controller is designed based on minimizing a suitably chosen quadratic performance index. A number of problem areas that arise in this context have been addressed. These include developing suitable methods for selecting an index of performance, both time domain and frequency domain methods for achieving robustness of the closed loop system, developing canonical forms to achieve a minimal parameterization for the controller, two time scale design formulations for ill-conditioned systems, and the development of convergent numerical algorithms for solving the output feedback problem.

Calise, Anthony J.↗
NASA NTRS2019

Pterodactyl: An Uncoupled Range Control Approach to Fully Numerical Predictor-Corrector Entry Guidance

Entry, descent, and landing (EDL) has been identified as a core area of investment in NASA's Strategic Technology Investment Plan (NASA STIP). STIP lists the space technologies needed to help achieve NASA's science, technology, and exploration goals across the agency. Within the EDL core area, deployable hypersonic decelerators, also known as deployable entry vehicles (DEVs), have been identified as an area of investment, due to its potential to revolutionize payload delivery methods to Earth and other planets. These vehicles, which can deploy their heat shields or alter their shape before entry, exploit an increased and more effective drag ratio by using less mass than traditional blunt body vehicles with rigid aeroshells. DEVs like Adaptive Deployable Entry and Placement Technology (ADEPT) and Hypersonic Inflatable Aerodynamic Decelerator (HIAD) have demonstrated the capability of transporting the equivalent science payloads of blunt body rigid aeroshells, while using a significantly smaller diameter when stowed within a launch vehicle. While DEVs' increased energy dissipation for less mass is an attractive feature, their ability to contract and expand would require advancements in the current state-of-the-art guidance and control (G&C) architectures used by traditional rigid vehicles. Pterodactyl, a project funded by NASA's Space Technology Mission Directorate (STMD), aims to provide feasible integrated G&C solutions for DEVs, complete with optimized vehicle designs and packaging analyses. Structural and aerodynamic analyses for the explored control systems suggested a need for a bank angle guidance algorithm, a heritage guidance approach that has been used in many entry precision targeting vehicles, as well as an additional need for the development of a non-bank angle guidance. For this reason, Pterodactyl will consider four different G&C configurations during its design phase: i) a reaction control system for bank (sigma) control, ii) a mass movement system for angle of attack (alpha) sideslip (beta) control, iii) flaps for alpha - beta control, and iv) flaps for sigma control. To increase the applicability of each proposed integrated G&C architecture, an 11 km/s lunar return demonstration mission is selected to stress the developed technology capability. The Lifting Nano-ADEPT (LNA) vehicle is chosen as the DEV to demonstrate the integrated solutions. This paper will detail the trajectory design for a lunar return mission, using the validated bank control guidance algorithm Fully Numerical Predictor-Corrector Entry Guidance (FNPEG) and a newly developed guidance algorithm: FNPEG Uncoupled Range Control (URC). FNPEG-URC diverges from traditional bank angle guidances by producing alpha and beta commands to thereby decouple downrange and crossrange control. This presentation will discuss the development and overall performance of FNPEG and FNPEG-URC for each of the four G&C configurations. Successful G&C configurations are defined as those that can deliver payloads to the intended descent and landing site while abiding by trajectory constraints in the face of dispersions.

Johnson, Breanna↗
NASA NTRS2011

CO2 Insulation for Thermal Control of the Mars Science Laboratory

The National Aeronautics and Space Administration (NASA) is sending a large (>850 kg) rover as part of the Mars Science Laboratory (MSL) mission to Mars in 2011. The rover's primary power source is a Multi-Mission Radioisotope Thermoelectric Generator (MMRTG) that generates roughly 2000 W of heat, which is converted to approximately 110 W of electrical power for use by the rover electronics, science instruments, and mechanism-actuators. The large rover size and extreme thermal environments (cold and hot) for which the rover is designed for led to a sophisticated thermal control system to keep it within allowable temperature limits. The pre-existing Martian atmosphere of low thermal conductivity CO2 gas (8 Torr) is used to thermally protect the rover and its components from the extremely cold Martian environment (temperatures as low as -130 deg C). Conventional vacuum based insulation like Multi Layer Insulation (MLI) is not effective in a gaseous atmosphere, so engineered gaps between the warm rover internal components and the cold rover external structure were employed to implement this thermal isolation. Large gaps would lead to more thermal isolation, but would also require more of the precious volume available within the rover. Therefore, a balance of the degree of thermal isolation achieved vs. the volume of rover utilized is required to reach an acceptable design. The temperature differences between the controlled components and the rover structure vary from location to location so each gap has to be evaluated on a case-by-case basis to arrive at an optimal thickness. For every configuration and temperature difference, there is a critical thickness below which the heat transfer mechanism is dominated by simple gaseous thermal conduction. For larger gaps, the mechanism is dominated by natural convection. In general, convection leads to a poorer level of thermal isolation as compared to conduction. All these considerations play important roles in the optimization process. A three-step process was utilized to design this insulation. The first step is to come up with a simple, textbook based, closed-form equation assessment of gap thickness vs. resultant thermal isolation achieved. The second step is a more sophisticated numerical assessment using Computational Fluid Dynamics (CFD) software to investigate the effect of complicated geometries and temperature contours along them to arrive at the effective thermal isolation in a CO2 atmosphere. The third step is to test samples of representative geometries in a CO2 filled chamber to measure the thermal isolation achieved. The results of these assessments along with the consistency checks across these methods leads to the formulation of design-guidelines for gap implementation within the rover geometry. Finally, based on the geometric and functional constraints within the real rover system, a detailed design that accommodates all these factors is arrived at. This paper will describe in detail this entire process, the results of these assessments and the final design that was implemented.

CO2↗
NASA NTRS2012

Adaptive control based on retrospective cost optimization

A discrete-time adaptive control law for stabilization, command following, and disturbance rejection that is effective for systems that are unstable, MIMO, and/or nonminimum phase. The adaptive control algorithm includes guidelines concerning the modeling information needed for implementation. This information includes the relative degree, the first nonzero Markov parameter, and the nonminimum-phase zeros. Except when the plant has nonminimum-phase zeros whose absolute value is less than the plant's spectral radius, the required zero information can be approximated by a sufficient number of Markov parameters. No additional information about the poles or zeros need be known. Numerical examples are presented to illustrate the algorithm's effectiveness in handling systems with errors in the required modeling data, unknown latency, sensor noise, and saturation.

Santillo, Mario A.↗
NASA NTRS2016

Automated Generation of Finite-Element Meshes for Aircraft Conceptual Design

This paper presents a novel approach for automated generation of fully connected finite-element meshes for all internal structural components and skins of a given wing-body geometry model, controlled by a few conceptual-level structural layout parameters. Internal structural components include spars, ribs, frames, and bulkheads. Structural layout parameters include spar/rib locations in wing chordwise/spanwise direction and frame/bulkhead locations in longitudinal direction. A simple shell thickness optimization problem with two load conditions is used to verify versatility and robustness of the automated meshing process. The automation process is implemented in ModelCenter starting from an OpenVSP geometry and ending with a NASTRAN 200 solution. One subsonic configuration and one supersonic configuration are used for numerical verification. Two different structural layouts are constructed for each configuration and five finite-element meshes of different sizes are generated for each layout. The paper includes various comparisons of solutions of 20 thickness optimization problems, as well as discussions on how the optimal solutions are affected by the stress constraint bound and the initial guess of design variables.

Li, Wu↗
NASA NTRS1987

Approximating the linear quadratic optimal control law for hereditary systems with delays in the control

The fundamental control synthesis issue of establishing a priori convergence rates of approximation schemes for feedback controllers for a class of distributed parameter systems is addressed within the context of hereditary systems. Specifically, a factorization approach is presented for deriving approximations to the optimal feedback gains for the linear regulator-quadratic cost problem associated with time-varying functional differential equations with control delays. The approach is based on a discretization of the state penalty which leads to a simple structure for the feedback control law. General properties of the Volterra factors of Hilbert-Schmidt operators are then used to obtain convergence results for the controls, trajectories and feedback kernels. Two algorithms are derived from the basic approximation scheme, including a fast algorithm, in the time-invariant case. A numerical example is also considered.

Milman, Mark H.↗
NASA NTRS1988

Approximating the linear quadratic optimal control law for hereditary systems with delays in the control

The fundamental control synthesis issue of establishing a priori convergence rates of approximation schemes for feedback controllers for a class of distributed parameter systems is addressed within the context of hereditary schemes. Specifically, a factorization approach is presented for deriving approximations to the optimal feedback gains for the linear regulator-quadratic cost problem associated with time-varying functional differential equations with control delays. The approach is based on a discretization of the state penalty which leads to a simple structure for the feedback control law. General properties of the Volterra factors of Hilbert-Schmidt operators are then used to obtain convergence results for the controls, trajectories and feedback kernels. Two algorithms are derived from the basic approximation scheme, including a fast algorithm, in the time-invariant case. A numerical example is also considered.

Milman, Mark H.↗
NASA NTRS1993

An integrated approach to spacecraft control design

Flight opreation of numerous spacecraft over the years has clearly demonstrated the inherant coupling between the vehicle structure and its control system. Even early missions, such as Explorer I, have experienced this coupling phenomenon. More recent and vivid examples are the Hubble Telescope and the Upper Atmospheric Research Satellite (UARS). In an effort to mitigate these problems and to aid the engineer in his task of achieving maximum performance from this design, even in the presence of structural flexibility, NASA has undertaken a program to provide the methodology for the optimal and integrated design of the vehicle structure and its control system. The analysis and design methodology developed is described. Anticipated performance gains to be realized from this methodology are demonstrated through computer simulation and supported by experimental validations of the design approach.

Keckler, C. R.↗
NASA NTRS1979

Formulations and applications of large structure actuator and sensor placements

A new approach based on the steady-state solutions of the optimal control and estimation problems is presented to study respectively the actuator and sensor locations for large flexible structures. A simple and computer-implementable formulation for minimizing the steady state optimal cost function and the state estimation error inherent in the estimation process is given. In conjunction with the new approach, two criteria are established relating the actuator and the sensor placement optimalities respectively to the minimums of the optimal cost function and the state estimation error. To illustrate the concepts of this paper, we present the results of some numerical and analytical studies on the actuator and the sensor locations of several simple flexible beam modes.

Juang, J.-N.↗