Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “multiple faults”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

Analysis of the survivability of the shuttle (ALT) fault-tolerant avionics system

An extension of the Complementary-Analytic-Simulative Technique (CAST) is presented which is applicable to the Shuttle Data Processing Subsystem (DPS). A two step process was used. The first step provides models, both analytic and simulative, for analysis of the Approach-Landing Test (ALT) configuration. The ALT modeling and analysis are presented. Since CAST had already been shown to be multicomputer systems, the emphasis was placed on extending the CAST concept so it is applicable to computer systems including the multiplicity of input and output devices found in a real-time control system application. The DPS mission-critical survivability for a six-hour mission was determined to be 0.999863 for the Shuttle ALT baseline configuration. Thus it can be said that for ALT, the survivability is adequate. However, the fact that orbiting missions of up to 30 days are planned illustrates the necessity of extending the ALT work to be applicable to OFT and actual mission scenarios. The above analysis led to the evaluation of three selected options which identified two areas of possible improvement. These improvements would result from use of a recovery technique which combines roll ahead with memory copy, and increased TACAN fault detectability.

Source record↗

Co-introduction of precipitate hardening and TRIP in a TWIP high-entropy alloy using friction stir alloying

Tuning deformation mechanisms is imperative to overcome the well-known strength-ductility paradigm. Twinning-induced plasticity (TWIP), transformation-induced plasticity (TRIP) and precipitate hardening have been investigated separately and have been altered to achieve exceptional strength or ductility in several alloy systems. In this study, we use a novel solid-state alloying method—friction stir alloying (FSA)—to tune the microstructure, and a composition of a TWIP high-entropy alloy by adding Ti, and thus activating site-specific deformation mechanisms that occur concomitantly in a single alloy. During the FSA process, grains of the as-cast face-centered cubic matrix were refined by high-temperature severe plastic deformation and, subsequently, a new alloy composition was obtained by dissolving Ti into the matrix. After annealing the FSA specimen at 900 °C, hard Ni–Ti rich precipitates formed to strengthen the alloy. An additional result was a Ni-depleted region in the vicinity of newly-formed precipitates. The reduction in Ni locally reduced the stacking fault energy, thus inducing TRIP-based deformation while the remaining matrix still deformed as a result of TWIP. Our current approach presents a novel microstructural architecture to design alloys, an approach that combines and optimizes local compositions such that multiple deformation mechanisms can be activated to enhance engineering properties.

36 MATERIALS SCIENCE↗

Refinements to the Graves–Pitarka Kinematic Rupture Generator, Including a Dynamically Consistent Slip-Rate Function, Applied to the 2019 Mw 7.1 Ridgecrest Earthquake

The main objective of this study is to develop physics–based constraints on the spatiotemporal variation of the slip–rate function using a simplified dynamic rupture model. First, we performed dynamic rupture modeling of the 2019 M w 7.1 Ridgecrest, California, earthquake, to analyze the effects of depth–dependent stress and material friction on slip rate. Then, we used our modeling results to guide refinements to the slip–rate function that were implemented in the Graves–Pitarka kinematic rupture generation technique. The dynamic ruptures were computed on a surface–rupturing, planar strike–slip fault that includes a weak (negative to low–stress–drop) zone in the upper 4 km of the crust. Below the weak zone, we placed high–stress–drop patches designed to mirror the large–slip areas seen in various rupture model inversions of the event. The locations of the high–stress–drop patches and the hypocenter were varied in multiple realizations to investigate how changing the dynamic conditions affected the resulting rupture kinematics, in particular, the slip rate. From these simulations, we observed a systematic change in the shape of the slip–rate function from Kostrov type below the weak zone to a predominantly symmetric shape within the weak zone, along with a depth–dependent reduction of peak slip rate. We generalized these shallow rupture features into a depth–dependent parametric variation of the slip–rate function and implemented it in the Graves–Pitarka kinematic rupture model generator. The performance of the updated kinematic approach was then verified in 0–4 Hz simulations of the M w 7.1 Ridgecrest earthquake, which showed that incorporating the depth–dependent variation in the shape of the slip–rate function improves the fit to the observed near–fault ground motions in the 0.5–3 s period range.

58 GEOSCIENCES↗

WinGridder-A graphic grid generator for TOUGH2 simulators (WinGridder) v3.0

WINGRIDDER V3.0 is a Windows-based software for designing and generating numerical grids for numerical simulators that are based on the "integral finite difference" or the "control volume" numerical scheme (e.g., TOUGH2, Pruess et al., 1996). The user can design and generate grid that properly represents the stratigraphic features, inclined faults, and repository. WINGRIDDER V3.0 is an upgrade from WINGRIDDER V2.0. This revision includes testable requirements as listed in the Requirements Document (RD), 10024-RD-3.0-00, Section 2. With new features, WINGRIDDER V3.0 adds the ability to generate a multiple-interactive-continuum (MINC) grid.

Pan, Lehua↗

Development and Application of Preliminary TOGA Model for CO 2 -EOR with Comparison to Resistivity Data

A new TOUGH code, TOGA (Transport of Oil, Gas, Aqueous), is used to model enhanced oil recovery (EOR) from a South Texas field where a combination of water, CO 2 , and WAG (water-alternating-gas) injection wells are located in the down-dip region of a fault block, with oil and natural gas production occurring from wells located up-dip. The reservoir is composed of interlayered sands and shales at a depth of about 2000 m. TOGA considers three fluid phases (oil, gas, and aqueous), and multiple components. Oil field data including compositional analysis of stock-tank oil, gas-oil ratio, and gas gravity are used to determine the composition of oil and gas phases. Initial conditions for aqueous saturation are determined from a depth to surface resistivity survey conducted prior to the onset of CO 2 injection and Archie’s Law. Simulation results after several years of EOR operations are then converted back to resistivity maps and compared to images created by time-lapse depth-to-surface resistivity surveys. These surveys show a strong increase in resistivity, interpreted as the replacement of aqueous phase by injected CO 2 . In contrast, preliminary TOGA results show that injected CO 2 displaced more oil than water, suggesting that the three-phase relative permeability curves used to describe the interference of fluid phases need to be modified. Limited information on the composition of produced fluids provides another data set for comparison with model results. Model variations including using different relative permeability curve parameters and WAG cycle durations yielded improved model matches to the field data. The practical simplifications needed to simulate an actual operating oil field and the limited amount of field operation data available preclude using the present model to get an accurate history match or to make detailed predictions. Rather, the modeling is intended to illustrate the general trends occurring during CO 2 -EOR and to indicate where more detailed information is needed.

02 PETROLEUM↗

Evolution of a standard microprocessor-based space computer

An existing in inventory computer hardware/software package (B-1 RFS/ECM) was repackaged and applied to multiple missile/space programs. Concurrent with the application efforts, low risk modifications were made to the computer from program to program to take advantage of newer, advanced technology and to meet increasingly more demanding requirements (computational and memory capabilities, longer life, and fault tolerant autonomy). It is concluded that microprocessors hold promise in a number of critical areas for future space computer applications. However, the benefits of the DoD VHSIC Program are required and the old proliferation problem must be revised.

Fernandez, M.↗

The Manson impact structure, a possible site for a Cretaceous-Tertiary (K-T) boundary impact

The Manson impact structure, about 35 km in diameter, is the largest impact crater recognized in the United States. Its center is located near the town of Manson, 29 km west of Fort Dodge, Iowa. The structure is not well known geologically because it is covered by tens of meters of glacial deposits. What is known about the structure was learned mostly from the study of water well cuttings. At Manson the normal Phanerozoic and Proterozoic sedimentary rocks were replaced by centrally uplifted Proterozoic crystalline rocks that are representative of the normal basement: This central uplift is surrounded by completely disrupted rocks which are roughly encircled by peripherally faulted and slumped sequences of normal sedimentary strata. Radially outward normal sedimentary strata are uplifted slightly. Manson, once interpreted as a cryptovolcanic structure, is now considered an impact structure based on its circular shape, its central uplift and the presence of multiple intersecting sets of shock lamellae in quartz grains from the central uplift. The Ar-40/Ar-39 age spectrum dating results for a microcline separate from the Manson 2-A core in the central uplift is shown. This spectrum is interpreted to indicate a nearly complete degassing of the microcline at the time of the Manson impact. The remainder of the gas released climbs in age with increasing temperature of release. This pattern of the age spectrum is interpreted to represent diffusional loss due to reheating at the time of the impact and during subsequent cooling. Shocked quartz grains, present in the iridium-bearing layer at the K-T boundary throughout the world, have a significantly larger size and are more abundant in the western interior of North America than elsewhere in the world. Furthermore, shocked feldspar and granitic fragments are found at the K-T boundary in North America. These observations indicate the K-T boundary impact must have penetrated continental crust in North America.

Hartung, J. B.↗

Astor Pass Seismic Surveys Preliminary Report

In collaboration with the Pyramid Lake Paiute Tribe (PLPT), the University of Nevada, Reno (UNR) and Optim re-processed, or collected and processed, over 24 miles of 2d seismic-reflection data near the northwest corner of Pyramid Lake, Nevada. The network of 2d land surveys achieved a near-3d density at the Astor Pass geothermal prospect that the PLPT drilled during Nov. 2010 to Feb. 2011. The Bureau of Indian Affairs funded additional seismic work around the Lake, and an extensive, detailed single-channel marine survey producing more than 300 miles of section, imaging more than 120 ft below the Lake bottom. Optim’s land data collection utilized multiple heavy vibrators and recorded over 200 channels live, providing a state-of-the-art reflection-refraction data set. After advanced seismic analysis including first-arrival velocity optimization and prestack depth migration, the 2d sections show clear fault-plane reflections, in some areas as deep as 4000 ft, tying to distinct terminations of the mostly volcanic stratigraphy. Some lines achieved velocity control to 3000 ft depth; all lines show reflections and terminations to 5000 ft depth. Three separate sets of normal faults appear in an initial interpretation of fault reflections and stratigraphic terminations, after loading the data into the OpendTect 3d seismic visualization system. Each preliminary fault set includes a continuous trace more than 3000 ft long, and a swarm of short fault strands. The three preliminary normal-fault sets strike northerly with westward dip, northwesterly with northeast dip, and easterly with north dip. An intersection of all three fault systems documented in the seismic sections at the end of Phase I helped to locate the APS-2 and APS-3 slimholes. The seismic sections do not show the faults connected to the Astor Pass tufa spire, suggesting that we have imaged mostly Tertiary-aged faults. We hypothesize that the Recent, active faults that produced the tufa through hotspring activity do not have enough offset to produce seismic terminations. We are conducting further high-resolution seismic studies (to 200 ft depths) at the tufa spire to test this hypothesis. Additional work in progress includes a collaborative, iterative joint interpretation of geologic mapping and the seismic sections for fault locations, building the geologic model; and 3d velocity modeling and imaging to locate additional faultplane images appearing between the 2d lines. Overall, the seismic exploration program cost less than $0.5M from all funders. It defines in detail the geologic structure of much of the north margin of Pyramid Lake.

01 COAL, LIGNITE, AND PEAT↗

Hydrogen and water interactions with CrMnFeCoNi alloy from density functional theory calculations

High entropy alloys (HEAs) are a promising class of materials with remarkable mechanical and catalytic properties. Among these, the quinary CrMnFeCoNi alloy (also called “Cantor alloy”) has attracted considerable attention given its thermodynamic stability and remarkable mechanical properties under different temperatures. Given that various degradation mechanisms involve multiple contaminants, such as hydrogen and water in hydrogen embrittlement and surface poisoning, respectively, understanding their interactions with the Cantor alloy is critical for its practical applications as structural, nuclear, or hydrogen storage material. In this work, we perform first-principles calculations based on Density Functional Theory (DFT) to investigate such interactions when considering various microstructures, including bulk materials and those containing certain defects, such as grain boundaries, stacking faults, and vacancies. We also employ Global Sensitivity Analysis to identify the importance of different factors in the stability of the impurities. We find that the accuracy of the H formation energy is significantly affected by spin polarization and chemical short-range order. The study also identifies a strong tendency for hydrogen interstitials to segregate to Σ5(210)/[001] symmetric tilt grain boundary, even when H concentrations are high, suggesting that a certain type of grain boundaries acts as H sinks within the alloy. Further, this result is reinforced by the low formation energy of vacancy-hydrogen complexes, which can contain multiple hydrogen atoms. Finally, the surface reactivity analysis reveals that the adsorption energy of oxygen and hydroxyl groups is highly sensitive to the specific metal atom involved in the binding, with a clear preference for chromium atoms, which could have implications for the alloy’s oxidation and corrosion behavior.

36 MATERIALS SCIENCE↗

Fidelity of an encoded [7,1,3] logical zero

I calculate the fidelity of a [7,1,3] Calderbank-Shor-Steane quantum error correction code logical zero state constructed in a nonequiprobable Pauli operator error environment for two methods of encoding. The first method is to apply fault-tolerant error correction to an arbitrary state of seven qubits utilizing Shor states for syndrome measurement. The Shor states are themselves constructed in the nonequiprobable Pauli operator error environment, and their fidelity depends on the number of verifications done to ensure multiple errors will not propagate into the encoded quantum information. Surprisingly, performing these verifications may lower the fidelity of the constructed Shor states. The second encoding method is to simply implement the [7,1,3] encoding gate sequence also in the nonequiprobable Pauli operator error environment. Perfect error correction is applied after both methods to determine the correctability of the implemented errors. I find that which method attains higher fidelity depends on which of the Pauli operators errors is dominant. Nevertheless, perfect error correction applied after the encoding suppresses errors to at least first order for both methods.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Autonomous power expert system

The goal of the Autonomous Power System (APS) program is to develop and apply intelligent problem solving and control technologies to the Space Station Freedom Electrical Power Systems (SSF/EPS). The objectives of the program are to establish artificial intelligence/expert system technology paths, to create knowledge based tools with advanced human-operator interfaces, and to integrate and interface knowledge-based and conventional control schemes. This program is being developed at the NASA-Lewis. The APS Brassboard represents a subset of a 20 KHz Space Station Power Management And Distribution (PMAD) testbed. A distributed control scheme is used to manage multiple levels of computers and switchgear. The brassboard is comprised of a set of intelligent switchgear used to effectively switch power from the sources to the loads. The Autonomous Power Expert System (APEX) portion of the APS program integrates a knowledge based fault diagnostic system, a power resource scheduler, and an interface to the APS Brassboard. The system includes knowledge bases for system diagnostics, fault detection and isolation, and recommended actions. The scheduler autonomously assigns start times to the attached loads based on temporal and power constraints. The scheduler is able to work in a near real time environment for both scheduling and dynamic replanning.

Ringer, Mark J.↗

Autonomous power expert system

The goal of the Autonomous Power System (APS) program is to develop and apply intelligent problem solving and control technologies to the Space Station Freedom Electrical Power Systems (SSF/EPS). The objectives of the program are to establish artificial intelligence/expert system technology paths, to create knowledge based tools with advanced human-operator interfaces, and to integrate and interface knowledge-based and conventional control schemes. This program is being developed at the NASA-Lewis. The APS Brassboard represents a subset of a 20 KHz Space Station Power Management And Distribution (PMAD) testbed. A distributed control scheme is used to manage multiple levels of computers and switchgear. The brassboard is comprised of a set of intelligent switchgear used to effectively switch power from the sources to the loads. The Autonomous Power Expert System (APEX) portion of the APS program integrates a knowledge based fault diagnostic system, a power resource scheduler, and an interface to the APS Brassboard. The system includes knowledge bases for system diagnostics, fault detection and isolation, and recommended actions. The scheduler autonomously assigns start times to the attached loads based on temporal and power constraints. The scheduler is able to work in a near real time environment for both scheduling an dynamic replanning.

Ringer, Mark J.↗

Fly-By-Light/Power-By-Wire Fault-Tolerant Fiber-Optic Backplane

The design and development of a fault-tolerant fiber-optic backplane to demonstrate feasibility of such architecture is presented. The simulation results of test cases on the backplane in the advent of induced faults are presented, and the fault recovery capability of the architecture is demonstrated. The architecture was designed, developed, and implemented using the Very High Speed Integrated Circuits (VHSIC) Hardware Description Language (VHDL). The architecture was synthesized and implemented in hardware using Field Programmable Gate Arrays (FPGA) on multiple prototype boards.

Malekpour, Mahyar R.↗

Benchmark study of a new simplified DFN model for shearing of intersecting fractures and faults

It is challenging to quantitatively predict shearing of intersecting fractures/faults because of dynamic frictional contacts accompanied by possible nonlinear rock deformation. To address such challenges, a new conceptual model—the simplified DFN model—was proposed and validated by Hu et al. 46 to use major paths (MPs) to represent complicated DFNs for calculation of shearing. In this work, we conducted a benchmark study for three examples that involve different levels of complexity of intersecting fractures, and correspondingly different numbers of MPs. The codes and software that were used in the benchmark cover a range of continuum, discontinuum and hybrid numerical methods: NMM (LBNL), FLAC3D (LBNL), GBDEM (KIGAM), FRACOD (DynaFrax), and CASRock (CAS). The general consistency between DFN and MP cases as predicted by all the codes/software demonstrates that major paths can be used to simplify the geometry of DFNs in a wide range of software. Disagreement in results made by some software and potential future improvements are discussed. We show that (1) shearing of one or multiple major fractures can be reduced if there are multiple smaller intersecting fractures in that area, which is a useful basis for understanding and controlling induced seismicity and merits further analysis, and (2) the agreement achieved in the benchmark examples provide confidence that the simplified DFN model is a promising conceptual model that can be used for different types of numerical approaches and software for simplifying the analysis of the shearing of intersecting fractures and faults.

58 GEOSCIENCES↗

Physics-Based Methods of Failure Analysis and Diagnostics in Human Space Flight

The Integrated Health Management (IHM) for the future aerospace systems requires to interface models of multiple subsystems in an efficient and accurate information environment at the earlier stages of system design. The complexity of modern aeronautic and aircraft systems (including e.g. the power distribution, flight control, solid and liquid motors) dictates employment of hybrid models and high-level reasoners for analysing mixed continuous and discrete information flow involving multiple modes of operation in uncertain environments, unknown state variables, heterogeneous software and hardware components. To provide the information link between key design/performance parameters and high-level reasoners we rely on development of multi-physics performance models, distributed sensors networks, and fault diagnostic and prognostic (FD&P) technologies in close collaboration with system designers. The main challenges of our research are related to the in-flight assessment of the structural stability, engine performance, and trajectory control. The main goal is to develop an intelligent IHM that not only enhances components and system reliability, but also provides a post-flight feedback helping to optimize design of the next generation of aerospace systems. Our efforts are concentrated on several directions of the research. One of the key components of our strategy is an innovative approach to the diagnostics/prognostics based on the real time dynamical inference (DI) technologies extended to encompass hybrid systems with hidden state trajectories. The major investments are into the multiphysics performance modelling that provides an access of the FD&P technologies to the main performance parameters of e.g. solid and liquid rocket motors and composite materials of the nozzle and case. Some of the recent results of our research are discussed in this chapter. We begin by introducing the problem of dynamical inference of stochastic nonlinear models and reviewing earlier results. Next, we present our analytical approach to the solution of this problem based on the path integral formulation. The resulting algorithm does not require an extensive global search for the model parameters, provides optimal compensation for the effects of dynamical noise, and is robust for a broad range of dynamical models. In the following Section the strengths of the algorithm are illustrated illustrated by inferring the parameters of the stochastic Lorenz system and comparing the results with those of earlier research. Next, we discuss a number of recent results in application to the development of the IHM for aerospace system. Firstly, we apply dynamical inference approach to a solution of classical three tank problems with mixed unknown continuous and binary parameters. The problem is considered in the context of ground support system for filling fuel tanks of liquid rocket motors. It is shown that the DI algorithm is well suited for successful solution of a hybrid version of this benchmark problem even in the presence of additional periodic and stochastic perturbation of unknown strength. Secondly, we illustrate our approach by its application to an analysis of the nozzle fault in a solid rocket motor (SRM). The internal ballistics of the SRM is modelled as a set of one-dimensional partial differential equations coupled to the dynamics of the propellant regression. In this example we are specifically focussed on the inference of discrete and continuous parameters of the nozzle blocking fault and on the possibility of an application of the DI algorithm to reducing the probability of "misses" of an on-board FD&P for SRM. In the next section re-contact problem caused by first stage/upper stage separation failure is discussed. The reaction forces imposed on the nozzle of the upper stage during the re-contact and their connection to the nozzle damage and to the thrust vector control (TVC) signal are obtained. It is shown that transient impact induced torquean be modelled as a response of an effective damped oscillator. A possible application of the DI algorithm to the inference of damage parameters and predicting fault dynamics ahead of time using the actuator signal is discussed. Finally, we formulate Bayesian inferential framework for development of the IHM system for in-flight structural health monitoring (SHM) of composite materials. We consider the signal generated by piezoelectric actuator mounted on composite structure generating elastic waves in it. The signal received by the sensor is than compared with the baseline signal. The possibility of damage inference is discussed in the context of development of the SHM.

Smelyanskiy, Vadim N.↗

Creating dynamic equivalent PV circuit models with impedance spectroscopy for arc-fault modeling.

Article 690.11 in the 2011 National Electrical Code{reg_sign} (NEC{reg_sign}) requires new photovoltaic (PV) systems on or penetrating a building to include a listed arc fault protection device. Currently there is little experimental or empirical research into the behavior of the arcing frequencies through PV components despite the potential for modules and other PV components to filter or attenuate arcing signatures that could render the arc detector ineffective. To model AC arcing signal propagation along PV strings, the well-studied DC diode models were found to inadequately capture the behavior of high frequency arcing signals. Instead dynamic equivalent circuit models of PV modules were required to describe the impedance for alternating currents in modules. The nonlinearities present in PV cells resulting from irradiance, temperature, frequency, and bias voltage variations make modeling these systems challenging. Linearized dynamic equivalent circuits were created for multiple PV module manufacturers and module technologies. The equivalent resistances and capacitances for the modules were determined using impedance spectroscopy with no bias voltage and no irradiance. The equivalent circuit model was employed to evaluate modules having irradiance conditions that could not be measured directly with the instrumentation. Although there was a wide range of circuit component values, the complex impedance model does not predict filtering of arc fault frequencies in PV strings for any irradiance level. Experimental results with no irradiance agree with the model and show nearly no attenuation for 1 Hz to 100 kHz input frequencies.

99 GENERAL AND MISCELLANEOUS↗

Efficient Floating-Point Arithmetic on Fault-Tolerant Quantum Computers

We propose a novel floating-point encoding scheme that builds on prior work involving fixed-point encodings. We encode floating-point numbers using Two's Complement fixed-point mantissas and Two's Complement integral exponents. We used our proposed approach to develop quantum algorithms for fundamental arithmetic operations, such as bit-shifting, reciprocation, multiplication, and addition. We prototyped and investigated the performance of the floating-point encoding scheme on quantum computer simulations by performing reciprocation on randomly drawn inputs and by solving first-order ordinary differential equations, while varying the number of qubits in the encoding. We observed rapid convergence to the exact solutions as we increased the number of qubits and a significant reduction in the number of ancilla qubits required for reciprocation when compared with similar approaches.

Serrallés, José Cruz [Weill Cornell Med. Coll.]↗