Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “model testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Can binary stars test solar models?

The position in the H-R diagram of the approximately solar-mass component of the Hyades eclipsing binary, HD 27130, is compared with the predictions of stellar structure theory. The stellar models are calibrated by matching a model with the solar heavy element composition and age to the solar radius and luminosity. The comparison to the Hyades binary then is a test of the prediction that the initial solar luminosity was only about 0.7 times the present solar luminosity. The agreement is satisfactory, lending a measure of confidence to the solar model employed, provided that the initial helium abundance of the Hyades stars is not greater than that of the sun and is not less by more than about 0.03 in Y. Unless the model is grossly incorrect, the inference of Stromgren, Olsen, and Gustafsson (1982) from the 'Hyades anomaly' in intermediate-band photometry that Y(Hyades) is less than Y(solar) by 0.1 or 0.15 is rejected by the observed properties of HD 27130.

Popper, D. M.↗
NASA NTRS1947

Spin and Recovery Characteristics of the Curtiss-Wright XP-87 Airplane

The spin and recovery characteristics of the Curtiss-Wright XP-87 airplane, as well as the spin-recovery parachute requirements, the control forces that would be encountered in the spin, and the best method for the crew to attempt an emergency escape, are presented in this report. The characteristics were estimated rather than determined by model tests because the XP-87 dimensional and mass characteristics were considered to be noncritical and because data were available from model tests of several similar airplanes. The study indicated that the recovery characteristics of the airplane will be satisfactory for all loadings if the controls are reversed fully and rapidly. The control forces, however, will probably be beyond the capabilities of the pilot unless some additional balance or a booster is used. A 6-foot tail parachute or a 3.5-foot wing-tip parachute with a drag coefficient of 0.7 will be a satisfactory, emergency spin-recovery device for spin demonstrations. If it is necessary for the crew to abandon the spinning airplane, they should leave from the outboard side of the cockpit.

Berman, Theodore↗
NASA NTRS2008

Using Pressure- and Temperature-Sensitive Paint for Global Surface Pressure and Temperature Measurements on the Aft-Body of a Capsule Reentry Vehicle

Pressure Sensitive Paint (PSP) and Temperature Sensitive Paint (TSP) were used to visualize and quantify the surface interactions of reaction control system (RCS) jets on the aft body of capsule reentry vehicle shapes. The first model tested was an Apollo-like configuration and was used to focus primarily on the effects of the forward facing roll and yaw jets. The second model tested was an early Orion Crew Module configuration blowing only out of its forward-most yaw jet, which was expected to have the most intense aerodynamic heating augmentation on the model surface. This paper will present the results from the experiments, which show that with proper system design, both PSP and TSP are effective tools for studying these types of interaction in hypersonic testing environments.

Watkins, A. Neal↗
NASA NTRS1976

Acoustics and aerodynamics of over-the-wing thrust reversers

As part of the Quiet Clean Short-Haul Experimental Engine Program, model tests were conducted to determine the effects of thrust reverser geometric parameters on noise and reverse thrust. The acoustic tests used a 1/6 scale model thrust reverser while the aerodynamic performance tests used a 1/12 scale model reverser. Parameters which were varied in both tests include blocker spacing, blocker height, lip angle, and lip length. The impact of these parameters on peak sideline noise and reverse thrust performance is discussed.

Stimpert, D. L.↗
DOE OSTI2023

Predicting discomfort from glare with pedestrian-scale lighting: A comparison of candidate models using four independent datasets

After dark, pedestrians may experience discomfort from glare caused by outdoor lighting. While several models for measuring discomfort have been proposed, there is no consensus as to which model should be used. The performances of different models were investigated using datasets from four independent studies, comparing the degree of association between model predictions and subjective ratings, and the ability of a model to distinguish between discomfort and non-discomfort situations. The models tested are those proposed by Petherbridge and Hopkinson in 1950, Schmidt-Clausen and Bindels in 1974, Bullough et al. in 2008 and Lin et al. in 2014 and 2015. They also include two quantities: direct illuminance at the eye from the glare source and average source luminance. Of the models tested, the best performance was found using either the model proposed by Bullough et al. in 2008 or by direct illuminance at the eye.

Abboushi, B.↗
NASA NTRS2006

Three-dimensional Myoblast Aggregates--Effects of Modeled Microgravity

The overall objective of these studies is to elucidate the molecular and cellular alterations that contribute to muscle atrophy in astronauts caused by exposure to microgravity conditions in space. To accomplish this, a three-dimensional model test system was developed using mouse myoblast cells (C2C12). Myoblast cells were grown as three-dimensional aggregates (without scaffolding or other solid support structures) in both modeled microgravity (Rotary Cell Culture System, Synthecon, Inc.) and at unit gravity in coated Petri dishes. Evaluation of H&E stained thin sections of the aggregates revealed the absence of any necrosis. Confocal microscopy evaluations of cells stained with the Live/Dead assay (Molecular Probes) confirmed that viable cells were present throughout the aggregates with an average of only three dead cells observed per aggregate. Preliminary results from gene array analysis (Affymetrix chip U74Av2) showed that approximately 14% of the genes were down regulated (decreased more than 3 fold) and 4% were upregulated in cells exposed to modeled microgravity for 12 hours compared to unit gravity controls. Additional studies using fluorescent phallacidin revealed a decrease in F-actin in the cells exposed to modeled microgravity compared to unit gravity. Myoblast cells grown as aggregates in modeled microgravity exhibited spontaneous differentiation into syncitia while no differentiation was seen in the unit gravity controls. These studies show that 1)the model test system developed is suitable for assessing cellular and molecular alterations in myoblasts; 2) gene expression alterations occur rapidly (within 12 hours) following exposure to modeled microgravity; and 3) modeled microgravity conditions stimulated myoblast cell differentiation. Achieving a greater understanding of the molecular alterations leading to muscle atrophy will eventually enable the development of cell-based countermeasures, which may be valuable for treatment of muscle diseases on Earth and future space explorations.

Byerly, Diane↗
NASA NTRS2021

Lunar Auger Dryer ISRU (LADI) Breadboard Testing and Model Validation

In 2009, the Lunar Reconnaissance Orbiter (LRO)and Lunar Crater Observation and Sensing Satellite(LCROSS) provided definitive proof of water in the Lunar’s southern permanently shadowed region (PSR)[1]. Both the 2020 NASA Technology Taxonomy[2] and the Lunar Surface Innovation Initiative (LSII) team identified capability gaps in icy regolith transfer and reactor processing in Permanently Shadowed Region(PSR) environmental conditions. A screw conveyor dryer system operating from inside the PSR can continuously process water (and volatiles) for both breathable air and propellant. NASA’s Johnson Space Center (JSC) began development of a similar sub-system for Mars operation in 2017 and fabricated a unique breadboard test stand for validating the feasibility of this concept. This testing was postponed with the redirection of NASA’s mission from Mars to Moon. A JSC led trade study[3] in FY20 formulated a plan to leverage existing hardware to test concept feasibility, developed a lunar auger dryer sizing tool, and identified that both a physical flow and thermal model is required to develop an Engineering Development Unit (EDU) for environmental testing. Beginning in FY21, the Game Changing Development Program (GCDP) funded a three-year technology development project to increase the Technology Readiness Level (TRL) of the Lunar Auger Dryer ISRU (LADI) subsystem to TRL 5.

Lunar↗
NASA NTRS2021

Lunar Auger Dryer ISRU (LADI) Breadboard Testing and Model Validation

In 2009, the Lunar Reconnaissance Orbiter (LRO)and Lunar Crater Observation and Sensing Satellite(LCROSS) provided definitive proof of water in the Lunar’s southern permanently shadowed region (PSR)[1]. Both the 2020 NASA Technology Taxonomy[2] and the Lunar Surface Innovation Initiative (LSII) team identified capability gaps in icy regolith transfer and reactor processing in Permanently Shadowed Region(PSR) environmental conditions. A screw conveyor dryer system operating from inside the PSR can continuously process water (and volatiles) for both breathable air and propellant. NASA’s Johnson Space Center (JSC) began development of a similar sub-system for Mars operation in 2017 and fabricated a unique breadboard test stand for validating the feasibility of this concept. This testing was postponed with the redirection of NASA’s mission from Mars to Moon. A JSC led trade study[3] in FY20 formulated a plan to leverage existing hardware to test concept feasibility, developed a lunar auger dryer sizing tool, and identified that both a physical flow and thermal model is required to develop an Engineering Development Unit (EDU) for environmental testing. Beginning in FY21, the Game Changing Development Program (GCDP) funded a three-year technology development project to increase the Technology Readiness Level (TRL) of the Lunar Auger Dryer ISRU (LADI) subsystem to TRL 5.

Lunar↗
NASA NTRS2018

Natural Frequency Testing and Model Correlation of Rocket Engine Structures in Liquid Hydrogen - Phase I, Cantilever Beam

Many structures in the launch vehicle industry operate in liquid hydrogen (LH2), from the hydrogen fuel tanks through the ducts and valves and into the pump sides of the turbopumps. Calculating the structural dynamic response of these structures is critical for successful qualification of this hardware, but accurate knowledge of the natural frequencies is based entirely on numerical or analytical predictions of frequency reduction due to the added-fluid-mass effect because testing in LH2 has always been considered too difficult and dangerous. This fluid effect is predicted to be approximately 4-5% using analytical formulations for simple cantilever beams. As part of a comprehensive test/analysis program to more accurately assess pump inducers operating in LH2, a series of frequency tests in LH2 were performed at NASA/Marshall Space Flight Center's unique cryogenic test facility. These frequency tests are coupled with modal tests in air and water to provide critical information not only on the mass effect of LH2, but also the cryogenic temperature effect on Young's Modulus for which the data is not extensive. The authors are unaware of any other reported natural frequency testing in this media. In addition to the inducer, a simple cantilever beam was also tested in the tank to provide a more easily modeled geometry as well as one that has an analytical solution for the mass effect. This data will prove critical for accurate structural dynamic analysis of these structures, which operate in a highly-dynamic environment.

Brown, Andrew M.↗
NASA NTRS1979

A model for testing centerfinding algorithms for automated optical navigation

An efficient software simulation of the imaging process for optical navigation is presented, illustrating results using simple examples. The problems of image definition and optical system modeling, including ideal image containing features and realistic models of optical filtering performed by the entire camera system, are examined. A digital signal processing technique is applied to the problem of developing methods of automated optical navigation and the subsequent mathematical formulation is presented. Specific objectives such as an analysis of the effects of camera defocusing on centerfinding of planar targets, addition of noise filtering to the algorithm, and implementation of multiple frame capability were investigated.

Griffin, M. D.↗
NASA NTRS1990

Thermomechanical deformation testing and modeling in the presence of metallurgical instabilities

A number of viscoplastic constitutive models were developed to describe deformation behavior under complex combinations of thermal and mechanical loading. Questions remain, however, regarding the validity of procedures used to characterize these models for specific structural alloys. One area of concern is that the majority of experimental data available for this purpose are determined under isothermal conditions. This experimental study is aimed at determining whether viscoplastic constitutive theories characterized using an isothermal data base can adequately model material response under the complex thermomechanical loading conditions typical of power generation service. The approach adopted was to conduct a series of carefully controlled thermomechanical experiments on a nickel-based superalloy, Hastelloy Alloy X. Previous investigations had shown that this material experiences metallurgical instabilities leading to complex hardening behavior, termed dynamic strain aging. Investigating this phenomenon under full thermomechanical conditions leads to a number of challenging experimental difficulties which up to the present work were unresolved. To correct this situation, a number of advances were made in thermomechanical testing techniques. Advanced methods for dynamic temperature gradient control, phasing control and thermal strain compensation were developed and incorporated into real time test control software. These advances allowed the thermomechanical data to be analyzed with minimal experimental uncertainty. The thermomechanical results were evaluated on both a phenomenological and microstructural basis. Phenomenological results revealed that the thermomechanical hardening trends were not bounded by those displayed under isothermal conditions. For the case of Hastelloy Alloy X (and similar dynamic strain aging materials), this strongly suggests that some form of thermomechanical testing is necessary when characterizing a thermoviscoplastic deformation model. Transmission electron microscopy was used to study the microstructural physics, and analyze the unique phenomenological behavior.

Castelli, Michael G.↗
NASA NTRS1981

Model aerodynamic test results for two variable cycle engine coannular exhaust systems at simulated takeoff and cruise conditions. Comprehensive data report. Volume 3: Graphical data book 1

A graphical presentation of the aerodynamic data acquired during coannular nozzle performance wind tunnel tests is given. The graphical data consist of plots of nozzle gross thrust coefficient, fan nozzle discharge coefficient, and primary nozzle discharge coefficient. Normalized model component static pressure distributions are presented as a function of primary total pressure, fan total pressure, and ambient static pressure for selected operating conditions. In addition, the supersonic cruise configuration data include plots of nozzle efficiency and secondary-to-fan total pressure pumping characteristics. Supersonic and subsonic cruise data are given.

Nelson, D. P.↗
NASA NTRS1985

Low-speed stability and control wind-tunnel investigations of effects of spanwise blowing on fighter flight characteristics at high angles of attack

The effects of spanwise blowing on two configurations representative of current fighter airplanes were investigated. The two configurations differed only in wing planform, with one incorporating a trapezoidal wing and the other a 60 delta wing. Emphasis was on determining the lateral-directional characteristics, particularly in the stall/departure angle-of-attack range; however, the effects of spanwise blowing on the longitudinal aerodynamics were also determined. The-tunnel tests included measurement of static force and forced-oscillation aerodynamic data, visualization of the airflow changes created by the spanwise blowing, and free-flight model tests. The effects of blowing rate, chordwise location of the blowing ports, asymmetric blowing, and blowing on the conventional aerodynamic control characteristics were investigated. In the angle-of-attack regions in which the spanwise blowing substantially improved the wing upper-surface flow field (i.e., provided reattachment of the flow aft of the leading-edge vortex), improvements in both static and dynamic lateral-directional stability were observed. Blowing effects on stability could be proverse or adverse depending on blowing rate, blowing port loaction, and wing planform. Free-flight model tests of the trapezoidal wing confirmed the beneficial effects of spanwise blowing measured in the static and dynamic force tests.

Satran, D. R.↗
NASA NTRS1977

Theoretical jet exhaust noise model for the duct burning turbofan

A model was developed to predict the acoustic power spectrum for a Duct Burning Turbofan (DBTF) whose cycle results in a high velocity, high temperature fan stream and a lower velocity, lower temperature primary stream. Model tests have demonstrated that a DBTF may produce substantially less noise than a conventional turbojet with the same thrust and weight flow. Predictions from the model agreed well with measured data from the model tests. The characteristics of the DBTF acoustic power spectrum were shown to be related to the rapid mixing of the fan and primary streams. The effects of fan to primary velocity ratio, temperature ratio, area ratio, and the effect of nozzle geometry on DBTF jet noise were determined.

Larson, R. S.↗
NASA NTRS1938

Tank Tests of Model 36 Flying Boat Hull

N.A.C.A. Model 36, a hull form with parallel middle body for half the length of the forebody and designed particularly for use with stub wings, was tested according to the general fixed-trim method over the range of practical loads, trims, and speeds. It was also tested free to trim with the center of gravity at two different positions. The results are given in the form of nondimensional coefficients. The resistance at the hump was exceptionally low but, at high planing speeds, afterbody interference made the performance only mediocre.

Allison, John↗
NASA NTRS2013

Develop a Model Component

During my internship at NASA, I was a model developer for Ground Support Equipment (GSE). The purpose of a model developer is to develop and unit test model component libraries (fluid, electrical, gas, etc.). The models are designed to simulate software for GSE (Ground Special Power, Crew Access Arm, Cryo, Fire and Leak Detection System, Environmental Control System (ECS), etc. ~.) before they are implemented into hardware. These models support verifying local control and remote software for End-Item Software Under Test (SUT). The model simulates the physical behavior (function, state, limits and 110) of each end-item and it's dependencies as defined in the Subsystem Interface Table, Software Requirements & Design Specification (SRDS), Ground Integrated Schematic (GIS), and System Mechanical Schematic.(SMS). The software of each specific model component is simulated through MATLAB's Simulink program. The intensiv~ model development life cycle is a.s follows: Identify source documents; identify model scope; update schedule; preliminary design review; develop model requirements; update model.. scope; update schedule; detailed design review; create/modify library component; implement library components reference; implement subsystem components; develop a test script; run the test script; develop users guide; send model out for peer review; the model is sent out for verific~tionlvalidation; if there is empirical data, a validation data package is generated; if there is not empirical data, a verification package is generated; the test results are then reviewed; and finally, the user. requests accreditation, and a statement of accreditation is prepared. Once each component model is reviewed and approved, they are intertwined together into one integrated model. This integrated model is then tested itself, through a test script and autotest, so that it can be concluded that all models work conjointly, for a single purpose. The component I was assigned, specifically, was a fluid component, a discrete pressure switch. The switch takes a fluid pressure input, and if the pressure is greater than a designated cutoff pressure, the switch would stop fluid flow.

Ensey, Tyler S.↗