Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “model order reduction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Development of Electrolytic Oxygen Recovery System for Advanced Life Support

The oxygen (O2) recovery system for the International Space Station (ISS) can recover approximately 50 percent of O2 from metabolic carbon dioxide (CO2). Increasing the O2 recovery rate and closing the open loop for future long duration crewed missions in space beyond Low Earth Orbit (LEO) is essential. There are several developmental efforts underway to increase the recovery rate. However, most of these technologies result in a complex, heavy, and power consuming system. The desired exploration O2 recovery system would be reliable and efficient with maximum O2 recovery. Marshall Space Flight Center (MSFC) is currently investigating an electrolytic O2 recovery approach that will increase the O2 recovery to greater than 70 percent as well as lowering the complexity, mass, and power consumption than most other technologies currently under development. The electrolytic O2 recovery system consists of a Microfluidic Electrochemical Reactor (MFECR) that is based on the electrochemical reduction of CO2 to O2 and ethylene (C2H4) using water (H2O) as precursor and operates at standard condition with a theoretical recovery rate of 73 percent. In 2016, NASA’s Game Changing Development Program awarded the University of Texas Arlington (UTA) a grant to initiate the development of the MFECR. Since 2019, MSFC and UTA have been collaborating with the current goals of increasing the O2 recovery efficiency, advancing the technology readiness to a Technology Readiness Level (TRL) 4, and maturing the system to process CO2 of one crew-member. Based on the results from UTA’s initial efforts, the following were identified as key areas of improvement in order to maximize O2 recovery for the system: further development of the anode material and cathode catalyst, model-based cell design optimization, and the addition of a separation system and fuel cell. This paper will present the current developmental efforts of the electrolytic system including MFECR design and overall system enhancements as well as results from single cell stack testing.

Brittany R Brown↗
NASA NTRS1983

An evaluation of circumferentially segmented duct liners

An evaluation of circumferentially segmented duct linings are performed by comparing attenuations of optimized segmented and uniform linings for a range of frequencies and source structures. Broadband suppression and the effects of changes to input modal structure are explored in these comparisons. Credence in the theoretical model was obtained by comparing predictions to results of a carefully controlled experiment performed on the Spinning Mode Synthesizer facility at the NASA Langley Research Center. Excellent agreement was obtained in these comparisons. Predicted results show that the optimized segmented liner is more effective than the optimized uniform liner for the higher order spinning mode sources with a hard-wall/soft-wall admittance variation representing an optimum configuration for the segmented liner. Predicted results also indicate that the segmented linear gives better broadband performance and that its suppression characteristics are not particularly sensitive to changes in input modal structure when compared to that of the uniform lining. It is shown that the greatest suppression benefit of segmented linings occur near mode cuton frequencies and that these benefits are obtained despite reductions in the total amount of acoustic treatment of fifty percent or more.

Watson, W. R.↗
NASA NTRS1989

A computationally efficient modelling of laminar separation bubbles

In order to predict the aerodynamic characteristics of airfoils operating at low Reynolds numbers, it is necessary to accurately account for the effects of laminar (transitional) separation bubbles. Generally, the greatest difficulty comes about when attempting to determine the increase in profile drag that results from the presence of separation bubbles. While a number of empirically based separation bubble models have been introduced in the past, the majority assume that the bubble development is fully predictable from upstream conditions. One way of accounting for laminar separation bubbles in airfoil design is the bubble analog used in the design and analysis program of Eppler and Somers. A locally interactive separation bubble model was developed and incorporated into the Eppler and Somers program. Although unable to account for strong interactions such as the large reduction in suction peak sometimes caused by leading edge bubbles, it is able to predict the increase in drag and the local alteration of the airfoil pressure distribution that is caused by bubbles occurring in the operational range which is of most interest.

Dini, Paolo↗
NASA NTRS1989

A computationally efficient modelling of laminar separation bubbles

In order to predict the aerodynamic characteristics of airfoils operating at low Reynolds numbers, it is necessary to accurately account for the effects of laminar (transitional) separation bubbles. Generally, the greatest difficulty comes about when attempting to determine the increase in profile drag that results from the presence of separation bubbles. While a number of empirically based separation bubble models have been introduced in the past, the majority assume that the bubble development is fully predictable from upstream conditions. One way of accounting for laminar separation bubbles in airfoil design is the bubble analog used in the design and analysis program of Eppler and Somers. A locally interactive separation bubble model was developed and incorporated into the Eppler and Somers program. Although unable to account for strong interactions such as the large reduction in suction peak sometimes caused by leading edge bubbles, it is able to predict the increase in drag and the local alteration of the airfoil pressure distribution that is caused by bubbles occurring in the operational range which is of most interest.

Dini, Paolo↗
NASA NTRS2016

Analysis and Characterization of Damage Utilizing an Orthotropic Generalized Composite Material Model Suitable for Use in Impact Problems

The need for accurate material models to simulate the deformation, damage and failure of polymer matrix composites under impact conditions is becoming critical as these materials are gaining increased usage in the aerospace and automotive communities. In order to address a series of issues identified by the aerospace community as being desirable to include in a next generation composite impact model, an orthotropic, macroscopic constitutive model incorporating both plasticity and damage suitable for implementation within the commercial LS-DYNA computer code is being developed. The plasticity model is based on extending the Tsai-Wu composite failure model into a strain hardening-based orthotropic plasticity model with a non-associative flow rule. The evolution of the yield surface is determined based on tabulated stress-strain curves in the various normal and shear directions and is tracked using the effective plastic strain. To compute the evolution of damage, a strain equivalent semi-coupled formulation is used in which a load in one direction results in a stiffness reduction in multiple material coordinate directions. A detailed analysis is carried out to ensure that the strain equivalence assumption is appropriate for the derived plasticity and damage formulations that are employed in the current model. Procedures to develop the appropriate input curves for the damage model are presented and the process required to develop an appropriate characterization test matrix is discussed.

Impact↗
NASA NTRS2016

Analysis and Characterization of Damage Utilizing an Orthotropic Generalized Composite Material Model Suitable for Use in Impact Problems

The need for accurate material models to simulate the deformation, damage and failure of polymer matrix composites under impact conditions is becoming critical as these materials are gaining increased usage in the aerospace and automotive communities. In order to address a series of issues identified by the aerospace community as being desirable to include in a next generation composite impact model, an orthotropic, macroscopic constitutive model incorporating both plasticity and damage suitable for implementation within the commercial LS-DYNA computer code is being developed. The plasticity model is based on extending the Tsai-Wu composite failure model into a strain hardening-based orthotropic plasticity model with a non-associative flow rule. The evolution of the yield surface is determined based on tabulated stress-strain curves in the various normal and shear directions and is tracked using the effective plastic strain. To compute the evolution of damage, a strain equivalent semi-coupled formulation is used in which a load in one direction results in a stiffness reduction in multiple material coordinate directions. A detailed analysis is carried out to ensure that the strain equivalence assumption is appropriate for the derived plasticity and damage formulations that are employed in the current model. Procedures to develop the appropriate input curves for the damage model are presented and the process required to develop an appropriate characterization test matrix is discussed

Impact↗
NASA NTRS2022

Europa Clipper Payload Verification and Validation: Avionics-Instrument Interface Test Campaign

NASA's Europa Clipper mission will investigate Jupiter's icy moon Europa using a payload suite consisting of nine instruments to address a range of scientific objectives concerning Europa's habitability. As the project proceeds past its Critical Design Review, confidence is being built in the system's ability to achieve mission objectives through the implementation of a rigorous payload verification and validation (V&V) program. As part of this payload V&V program, instrument box-level testing was performed by the payload team to verify select instrument-avionics interface requirements. This testing was performed at JPL using the avionics testbed's Bulk Data Storage Emulator (BDSEM) with visiting instrument Test Models. This paper summarizes the Data Link test campaign involving roughly four days of functional testing per instrument, including planning, testing methods, types of issues found, and the requirement closure process. Detail is also provided on the development, deployment, and validation of a standardized analysis tool used in data reviews. This testing verified requirements related to commanding rates, loss of link, packet format, clock counters, loopback test capability, and SpaceWire jitter and skew margins. Additional risk reduction testing of basic commanding, counter behavior, science data collection and transfer, and interface swapping was also performed. Because the BDSEM venue was not originally designed to be a run for record venue, the process of characterizing venue fidelity and establishing suitability for requirement closure using data collected in this venue will also be addressed.In order to close requirements, an extensible tool was developed to post-process instrument command and telemetry data from their original binary to a human-readable format and give visibility to errors detected within the data, such as packets with Cyclic Redundancy Check errors. This tool, called payload-packet-parser, is a Python 3.9 command line tool built using a variety of open-source Python libraries. Payload-packet-parser was designed to support parsing command and telemetry packets for all Europa Clipper instruments and additional analysis tools were developed for verification of specific information interface requirements. This test campaign, including post-processing using a single parsing and verification toolset, allowed for early interface testing, alleviating testing burdens on instrument teams and buying down risk on the instrument-avionics interface by finding hardware and software issues and idiosyncrasies prior to integration with system test venues. Over twenty issues were discovered across the payload, resulting in software updates and instrument rework well in advance of any system impacts. This paper concludes with an assessment of benefits and costs of this type of testing and lessons learned.

Montanez, Leticia↗
NASA NTRSDate not supplied

Modeling the Integrated Thermal Amine Scrubber and Air Cooled-Temperature Swing Adsorbent Compressor

As part of a larger CO2 removal architecture study, a model was developed in Aspen Custom Modeler of the Thermal Amine Scrubber (TAS), an ISS flight experiment intended to scrub CO2 from the cabin air. In order to minimize mass losses, it was determined the TAS should work in conjunction with the Air Cooled-Temperature Swing Adsorption Compressor (AC-TSAC) to reduce the CO2 for O2 production. First the TAS removes CO2 from the cabin atmosphere, then the AC-TSAC compresses the CO2 and feeds it in a steady steam to a Sabatier or Bosch process. This document details an effort to add a model of the AC-TSAC to the existing TAS model to determine if the two hardware systems will have deleterious effects on each other’s performance. It was found the AC-TSAC provided sufficient vacuum for the TAS’s desorption to occur, but not the same level of vacuum as space vacuum. This lower quality vacuum led to a reduction in the total cyclical uptake capacity of the TAS and thus a lower CO2 removal under the same conditions. The TAS did not remove enough CO2 to fill the AC-TSAC bed to capacity during the production phase which caused the AC-TSAC to run out of CO2 during production. This renders the addition of the AC-TSAC pointless. It is believed these effects can be overcome with a redesign of one or both systems.

TAS↗
NASA NTRS1990

Application of a Reynolds stress turbulence model to the compressible shear layer

Theoretically based turbulence models have had success in predicting many features of incompressible, free shear layers. However, attempts to extend these models to the high-speed, compressible shear layer have been less effective. In the present work, the compressible shear layer was studied with a second-order turbulence closure, which initially used only variable density extensions of incompressible models for the Reynolds stress transport equation and the dissipation rate transport equation. The quasi-incompressible closure was unsuccessful; the predicted effect of the convective Mach number on the shear layer growth rate was significantly smaller than that observed in experiments. Having thus confirmed that compressibility effects have to be explicitly considered, a new model for the compressible dissipation was introduced into the closure. This model is based on a low Mach number, asymptotic analysis of the Navier-Stokes equations, and on direct numerical simulation of compressible, isotropic turbulence. The use of the new model for the compressible dissipation led to good agreement of the computed growth rates with the experimental data. Both the computations and the experiments indicate a dramatic reduction in the growth rate when the convective Mach number is increased. Experimental data on the normalized maximum turbulence intensities and shear stress also show a reduction with increasing Mach number.

Sarkar, S.↗
NASA NTRS1990

Application of a Reynolds stress turbulence model to the compressible shear layer

Theoretically based turbulence models have had success in predicting many features of incompressible, free shear layers. However, attempts to extend these models to the high-speed, compressible shear layer have been less effective. In the present work, the compressible shear layer was studied with a second-order turbulence closure, which initially used only variable density extensions of incompressible models for the Reynolds stress transport equation and the dissipation rate transport equation. The quasi-incompressible closure was unsuccessful; the predicted effect of the convective Mach number on the shear layer growth rate was significantly smaller than that observed in experiments. Having thus confirmed that compressibility effects have to be explicitly considered, a new model for the compressible dissipation was introduced into the closure. This model is based on a low Mach number, asymptotic analysis of the Navier-Stokes equations, and on direct numerical simulation of compressible, isotropic turbulence. The use of the new model for the compressible dissipation led to good agreement of the computed growth rates with the experimental data. Both the computations and the experiments indicate a dramatic reduction in the growth rate when the convective Mach number is increased. Experimental data on the normalized maximum turbulence intensities and shear stress also show a reduction with increasing Mach number.

Sarkar, S.↗
NASA NTRS2015

Mars2020 Entry, Descent, and Landing Instrumentation (MEDLI2): Science Objectives and Instrument Requirements

NASAs exploration and technology roadmaps call for capability advancements in Mars entry, descent, and landing (EDL) systems to enable increased landed mass, a higher landing precision, and a wider planetary access. It is also recognized that these ambitious EDL performance goals must be met while maintaining a low mission risk in order to pave the way for future human missions. As NASA is engaged in developing new EDL systems and technologies via testing at Earth, instrumentation of existing Mars missions is providing valuable engineering data for performance improvement, risk reduction, and an improved definition of entry loads and environment. The most notable recent example is the Mars Entry, Descent and Landing Instrument (MEDLI) suite hosted by Mars Science Laboratory for its entry in Aug 2012. The MEDLI suite provided a comprehensive dataset for Mars entry aerodynamics, aerothermodynamics and thermal protection system (TPS) performance. MEDLI data has since been used for unprecedented reconstruction of aerodynamic drag, vehicle attitude, in-situ atmospheric density, aerothermal heating, and transition to turbulence, in-depth TPS performance and TPS ablation. [1,2] In addition to validating predictive models, MEDLI data has demonstrated extra margin available in the MSL forebody TPS, which can potentially be used to reduce vehicle parasitic mass. The presentation will introduce a follow-on MEDLI instrumentation suite (called MEDLI2) that is being developed for Mars-2020 mission. MEDLI2 has an enhanced scope that includes backshell instrumentation, a wider forebody coverage, and instruments that specifically target supersonic aerodynamics. Similar to MEDLI, MEDLI2 uses thermal plugs with embedded thermocouples and ports through the TPS to measure surface pressure. MEDLI2, however, also includes heat flux sensors in the backshell and a low range pressure transducer to measure afterbody pressure.

Aerothermodynamics↗
NASA NTRSDate not supplied

Jet Noise Modeling Using an Acoustic Analogy: From Theoretical Formulation to Practical Noise Predictions

In this presentation an overview of the development of an acoustic analogy formulation, and its implementation into a reduced-order prediction method for turbulent jet mixing noise, will be given. The definition and rationale of an acoustic analogy approach to the prediction of flow-generated noise will be provided. A high-level description of the mathematical processes involved will be outlined in the context of a particular formulation developed at NASA Glenn Research Center. The modelling approximations needed to implement the general theoretical formulation into a practical noise prediction tool will be discussed. Sample results obtained using a noise prediction code based on the NASA Glenn formulation, and comparisons with experimental data, will be presented for a series of turbulent jet test cases. A view on the prospects for continued use of acoustic analogy-based methods for the prediction of flow-generated noise and the assessment of noise-reduction technologies will conclude the presentation.

Jet noise↗
NASA NTRS2023

Fully Coupled Aeroelastic Stability Analysis of Adaptive Shape Memory Alloy Structural Technologies for Airframe Noise Reduction

This final report documents work performed by ATA Engineering, Inc., (ATA) to develop computational models and analyze the coupled fluid-structure response of two types of noise treatments applied to the leading-edge-slat component of a high-lift system typical of modern transport aircraft. The first treatment is a slat-gap filler (SGF), which closes the gap between the suction surfaces of a deployed slat and an aircraft main wing, and the second treatment is a slat-cove filler (SCF), which replaces the recirculating flow on the slat cove with a surface that promotes flow attachment. The representative airframe chosen for this work was NASA’s High-Lift Common Research Model (CRM-HL) in a baseline high-lift configuration. Superelastic shape memory alloys (SMAs) have been identified as enabling materials for these structural treatments. Since the technology elements rely upon having a highly reconfigurable structure, designs were assessed for their static aeroelastic deflection as well as their dynamic aeroelastic stability using coupled computational fluid dynamics (CFD) and nonlinear computational structural dynamics (NL-CSD) tools. Specifically, fluid-structure interaction (FSI) problems were solved computationally using the CFD solver Loci/CHEM and the NL-CSD solver Abaqus. As a part of the overall project, a similar capability was implemented using the CFD solver FUN3D coupled to Abaqus, although that work is documented in a separate report and that FSI framework was not used to analyze any of NASA’s SGF and SCF configurations. The technical approach consisted of solving for the flow field around the entire vehicle using a global CFD model, followed by extraction of relevant local subdomain data for CFD and NL-CSD co-simulations. The SGF design was analyzed using both 2D and 3D co-simulations to predict quasi-static aeroelastic deformations and to assess dynamic aeroelastic stability, whereas the SCF was analyzed in 2D only. SGF static aeroelastic response predictions focused on characterizing the deformed shape, with maximum displacements predicted to be on the order of magnitude of the technology element panel thickness. SGF dynamic aeroelastic response predictions used Partial Floquet analysis of the temporal evolution of selected nodal displacements to quantify the sign and magnitude of aeroelastic damping. Results suggest that the CRM-HL operating conditions would result in a dynamically stable response. The simulated dynamic pressure was also increased up to a factor of about four, and resulting responses suggest that predicted dynamic stability would be achieved with some margin.

Fluid Structure Interaction↗
NASA NTRSDate not supplied

Investigating the Numerical Stability of Using an Impedance Boundary Condition to Model Broadband Noise Scattering With Acoustic Liners

Reducing aircraft noise is a major objective in the field of computational aeroacoustics. When designing next generation quiet aircraft, it is important to be able to accurately and efficiently predict the acoustic scattering by an aircraft body from a given noise source. Acoustic liners are an effective tool for achieving aircraft noise reduction and are characterized by a frequency-dependent impedance value. Converted into the time-domain using Fourier transforms, an impedance boundary condition can be used to simulate the acoustic wave scattering by geometric bodies treated with acoustic liners. A Broadband Impedance Model will be discussed in which the liner impedance is specified along a wide range of frequencies. The liner impedance boundary condition will be derived and coupled with a time-domain boundary integral equation to model acoustic scattering by a flat plate consisting of both un-lined and lined surfaces. The scattering solution will be obtained iteratively using both spatial and temporal basis functions and the stability will be demonstrated through eigenvalue analysis. Stability will be assessed for its dependence on time step, spatial discretization, as well as temporal basis function order. Both second- and third-order Lagrange temporal basis functions are considered.

acoustics↗
NASA NTRSDate not supplied

Investigating the Numerical Stability of Using an Impedance Boundary Condition to Model Broadband Noise Scattering With Acoustic Liners

Reducing aircraft noise is a major objective in the field of computational aeroacoustics. When designing next generation quiet aircraft, it is important to be able to accurately and efficiently predict the acoustic scattering by an aircraft body from a given noise source. Acoustic liners are an effective tool for achieving aircraft noise reduction and are characterized by a frequency-dependent impedance value. Converted into the time-domain using Fourier transforms, an impedance boundary condition can be used to simulate the acoustic wave scattering by geometric bodies treated with acoustic liners. A Broadband Impedance Model will be discussed in which the liner impedance is specified along a wide range of frequencies. The liner impedance boundary condition will be derived and coupled with a time-domain boundary integral equation to model acoustic scattering by a flat plate consisting of both un-lined and lined surfaces. The scattering solution will be obtained iteratively using both spatial and temporal basis functions and the stability will be demonstrated through eigenvalue analysis. Stability will be assessed for its dependence on time step, spatial discretization, as well as temporal basis function order. Both second- and third-order Lagrange temporal basis functions are considered.

acoustics↗
NASA NTRS2000

Sugars as the optimal biosynthetic carbon substrate of aqueous life throughout the universe

Our previous analysis of the energetics of metabolism showed that both the biosynthesis of amino acids and lipids from sugars, and the fermentation of organic substrates, were energetically driven by electron transfer reactions resulting in carbon redox disproportionation (Weber, 1997). Redox disproportionation--the spontaneous (energetically favorable) direction of carbon group transformation in biosynthesis--is brought about and driven by the energetically downhill transfer of electron pairs from more oxidized carbon groups (with lower half-cell reduction potentials) to more reduced carbon groups (with higher half-cell reduction potentials). In this report, we compare the redox and kinetic properties of carbon groups in order to evaluate the relative biosynthetic capability of organic substrates, and to identify the optimal biosubstrate. This analysis revealed that sugars (monocarbonyl alditols) are the optimal biosynthetic substrate because they contain the maximum number of biosynthetically useful high energy electrons/carbon atom while still containing a single carbonyl group needed to kinetically facilitate their conversion to useful biosynthetic intermediates. This conclusion applies to aqueous life throughout the Universe because it is based on invariant aqueous carbon chemistry--primarily, the universal reduction potentials of carbon groups.

NASA Center ARC↗
NASA NTRS1997

Analysis of Smart Composite Structures Including Debonding

Smart composite structures with distributed sensors and actuators have the capability to actively respond to a changing environment while offering significant weight savings and additional passive controllability through ply tailoring. Piezoelectric sensing and actuation of composite laminates is the most promising concept due to the static and dynamic control capabilities. Essential to the implementation of these smart composites are the development of accurate and efficient modeling techniques and experimental validation. This research addresses each of these important topics. A refined higher order theory is developed to model composite structures with surface bonded or embedded piezoelectric transducers. These transducers are used as both sensors and actuators for closed loop control. The theory accurately captures the transverse shear deformation through the thickness of the smart composite laminate while satisfying stress free boundary conditions on the free surfaces. The theory is extended to include the effect of debonding at the actuator-laminate interface. The developed analytical model is implemented using the finite element method utilizing an induced strain approach for computational efficiency. This allows general laminate geometries and boundary conditions to be analyzed. The state space control equations are developed to allow flexibility in the design of the control system. Circuit concepts are also discussed. Static and dynamic results of smart composite structures, obtained using the higher order theory, are correlated with available analytical data. Comparisons, including debonded laminates, are also made with a general purpose finite element code and available experimental data. Overall, very good agreement is observed. Convergence of the finite element implementation of the higher order theory is shown with exact solutions. Additional results demonstrate the utility of the developed theory to study piezoelectric actuation of composite laminates with pre-existing debonding. Significant changes in the modes shapes and reductions in the control authority result due to partially debonded actuators. An experimental investigation addresses practical issues, such as circuit design and implementation, associated with piezoelectric sensing and actuation of composite laminates. Composite specimens with piezoelectric transducers were designed, constructed and tested to validate the higher order theory. These specimens were tested with various stacking sequences, debonding lengths and gains for both open and closed loop cases. Frequency changes of 15% and damping on the order of more than 20% of critical damping, via closed loop control, was achieved. Correlation with the higher order theory is very good. Debonding is shown to adversely affect the open and closed loop frequencies, damping ratios, settling time and control authority.

Chattopadhyay, Aditi↗
NASA NTRS2016

Modeling and Simulation of Radiative Compressible Flows in Aerodynamic Heating Arc-Jet Facility

Numerical simulations of an arc heated flow inside NASA's 20 [MW] Aerodynamics heating facility (AHF) are performed in order to investigate the three-dimensional swirling flow and the current distribution inside the wind tunnel. The plasma is considered in Local Thermodynamics Equilibrium(LTE) and is composed of Air-Argon gas mixture. The governing equations are the Navier-Stokes equations that include source terms corresponding to Joule heating and radiative cooling. The former is obtained by solving an electric potential equation, while the latter is calculated using an innovative massively parallel ray-tracing algorithm. The fully coupled system is closed by the thermodynamics relations and transport properties which are obtained from Chapman-Enskog method. A novel strategy was developed in order to enable the flow solver and the radiation calculation to be preformed independently and simultaneously using a different number of processors. Drastic reduction in the computational cost was achieved using this strategy. Details on the numerical methods used for space discretization, time integration and ray-tracing algorithm will be presented. The effect of the radiative cooling on the dynamics of the flow will be investigated. The complete set of equations were implemented within the COOLFluiD Framework. Fig. 1 shows the geometry of the Anode and part of the constrictor of the Aerodynamics heating facility (AHF). Fig. 2 shows the velocity field distribution along (x-y) plane and the streamline in (z-y) plane.

Pasma flows↗