Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “microstructural analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Increasing the Pressure‐Free Stripping Capacity of the Lithium Metal Anode in Solid‐State‐Batteries by Carbon Nanotubes

Abstract Lithium metal is the key anode material for solid‐state‐batteries as its successful implementation will drastically increase their energy and power densities. However, anode contact loss during stripping leads to dendrites upon plating and subsequent cell failure. Design strategies to mitigate these issues are crucial to enable the use of lithium metal anodes. This paper reports the dissolution kinetics of composite anodes made of lithium metal and carbon nanotubes (CNTs) with a garnet‐type solid electrolyte (SE). In addition to an enhancement of the effective diffusion within the anode, its dissolution is fundamentally changed from being 2D to 3D. By maintaining contact with the SE, the CNTs facilitate lithium transport to the interface, which yields more than 20 mAh cm −2 discharge capacity at 100 µ A cm −2 without the application of external stack pressure ( > 1 MPa). Conclusions drawn from electrochemical data on the anode microstructure are validated using cryo‐focused‐ion‐beam scanning electron microscopy and correlated with the mechanical properties. Micro‐indentation, acoustic analysis, and stress–strain testing show that mechanical properties of the anode, like yield strength and hardness, are adjustable. Overall, it is shown that the mechanical and electrochemical properties of Li–CNT composite electrodes can be tailored to suit the requirements of a practical cell.

Fuchs, Till↗
DOE OSTI2025

Fused filament fabrication of thermoplastic polyurethane composites with microencapsulated phase-change material

Here, the present study examines the thermal energy storage (TES) effectiveness and printability of microencapsulated phase-change material (MEPCM) combined with thermoplastic polyurethane (TPU) for fused filament fabrication (FFF). Two formulations were assessed: 24D MEPCM, which changes phase at 24 ° C, compounded with TPU pellets and 43D MEPCM, which changes phase at 43 ° C, integrated with TPU powder. These combinations are designed to evaluate the effectiveness of the form of the TPU (pellets versus powder) in the FFF process. The investigation includes a comprehensive analysis of thermal characteristics, encompassing phase-change temperature, latent heat of fusion, thermal conductivity, and thermal decomposition, which are assessed through differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). Additionally, mechanical properties, including stress-strain behavior, are examined to evaluate material suitability for TES applications, while microstructural visualization is used to provide deeper insights into material performance, structural integrity, and the quality of printed components. The 24D MEPCM and TPU pellets formulation experienced a significant loss of approximately 39.6% of PCM during filament extrusion and printing, resulting in a reduced effective latent heat. Therefore, further characterization of the pellet formulation was discontinued due to excessive leakage. In contrast, the 43D MEPCM and TPU powder formulation demonstrated minimal PCM loss, with the 60 wt.% composition achieving an effective latent heat of 132 J/g. This value represents the highest effective latent heat currently documented in the literature for PCM-polymer-composite materials produced using an FFF-based additive manufacturing process.

25 ENERGY STORAGE↗
DOE OSTI2021

Wide-blocky veins explained by dependency of crystal growth rate on fracture surface type: Insights from phase-field modeling

Vein microstructures contain a wealth of information on coupled chemical and mechanical processes of fracturing, fluid transport, and crystal growth. Numerical simulations have been used for exploring the factors controlling the development of vein microstructures; however, they have not been quantitatively validated against natural veins. Here we combined phase-field modeling with microtextural analysis of previously unexplained wide-blocky calcite veins in natural limestone and of the fresh fracture surface in this limestone. Results show that the wide-blocky vein textures can only be reproduced if ~10%–20% of crystals grow faster than the rest. This fraction corresponds to the amount of transgranularly broken grains that were observed on the experimental fracture surfaces, which are dominantly intergranular. We hypothesize that transgranular fractures allow faster growth of vein minerals due to the lack of clay coatings and other nucleation discontinuities that are common along intergranular cracks. Our simulation results show remarkable similarity to the natural veins and reproduce the nonlinear relationship between vein crystal width and vein aperture. This allows accurate simulations of crystal growth processes and related permeability evolution in fractured rocks.

Geology↗
DOE OSTI2021

Report on Properties and Microstructure of 3D Printed Inc-718

The report presents the microstructure and mechanical properties of 3D printed Inconel 718 to assess its potential use as a structural material for the Transformation Challenge Reactor (TCR). The structural components near the outlet of the core will experience significant neutron fluxes and outlet coolant temperatures from the hot standby temperature of 300°C to nearly 550°C at the center of the part. These components must support the core in appropriate loading conditions and require structural analysis at relevant temperatures. Strong spatial and chemical heterogeneity was found in as-built (ASB) Inconel 718. Three heat treatments were designed and conducted to simplify the microstructure and determine how each precipitating phase contributed to the overall strength. Baseline mechanical properties were measured from uniaxial tensile tests on subsize SS-J2 specimens at room temperature and at elevated temperatures of 300, 450, and 600°C. Microstructure electron microscopy was performed on ASB Inconel 718 and heat treated to correlate the observed mechanical properties with nanoscale features. Homogenization of the microstructure led to a highly ductile Inconel with lower strength compared with wrought Inconel 718. The tensile properties of additively manufactured 718 using a standard ASTMrecommended heat treatment were consistent with literature and with the ASTM for the properties of this alloy. A higher fraction of the δ phase led to shorter uniform elongation without altering other engineering properties.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Insight into the interfacial microstructure and chemistry of hot isostatically pressed AA6061-AA6061 bonds for U-10Mo fuel cladding application

Here, in the present study, hot isostatic pressing (HIP) bonding was carried out using AA6061-AA6061 plates for U-10Mo monolithic fuel cladding application. HIP was performed at 560°C with an applied isostatic pressure of 103 MPa for 90 min. Interfacial microstructure characterizations were performed using scanning electron microscopy (SEM) combined with electron backscatter diffraction (EBSD) to quantify precipitate fractions and study recrystallization, grain growth, and orientation relationships across the interface. EBSD results confirmed that no interfacial grain growth occurred during the HIP process. Transmission electron microscopy (TEM) was also employed to quantify composition and identify phases of various precipitates and an oxide layer that formed at the interface during HIP bonding. Microstructural analyses revealed the formation of a large fraction of Mg 2 Si precipitate and a ~50 nm thick Mg-oxide layer at the interface. Further TEM analysis confirmed that the oxide layer was not continuous, and Mg 2 Al 2 O 5 oxide particles with an average size of 18 nm were present in the oxide layer. Finite element modeling analysis was performed to study the stress distribution at the interface during HIP processing.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

The onset of alloying in Cu-Ni powders under high-shear consolidation

Friction consolidation (FC) is a solid phase processing methodology that densifies a material through high-shear deformation and pressure at elevated temperature. The method has garnered interest in the scientific community because of its ability to produce extremely refined and homogeneous microstructures, off-axis texture development, and improved material properties. This manuscript presents an investigation of Cu and Ni material mixing via evaluation of morphological evolution, grain boundary characterization, and compositional analysis to provide insights on the operational alloying mechanisms occurring under high shear and elevated temperature. Using correlative microscopy techniques, we show alloying progresses via a combination of grain boundary diffusion and interfacial roughening at heterophane boundaries. Evidence supporting Cu infiltration along Ni-Ni grain boundaries along with asymmetric diffusion of Cu into Ni grains is highlighted. The resultant, consolidated microstructure was produced directly from a powder compact in ~30 s and exhibited a submicron, equiaxed grain size.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Utilizing Oxygen Redox in Layered Cathode Materials from Multiscale Perspective

We report in high-capacity layered oxide cathode materials, utilization of lattice oxygen as a redox center is considered to be one of the most promising approaches to overcome the capacity limitation set by conventional transition metal redox centers. However, rapid material degradation is often associated with oxygen oxidation, leading to formidable challenges in utilizing oxygen redox. Further mechanistic understanding of the oxygen activities thus becomes critical to better control oxygen redox reactions. This review summarizes recent advances for investigating oxygen redox reactions in cathode materials from a multiscale perspective, i.e., from the atomistic level to the microstructure regime. First the mechanistic aspects of oxygen redox and the consequences of this reaction on various electrode degradation pathways during battery operation (e.g., oxygen loss, transition metal migration, irreversible phase transition), relating structural changes at the crystallographic scale to those at the macro scale, are discussed. Then recent developments based on atomic and microstructure modifications that are promising for improving the reversibility of oxygen redox reaction or mitigating the harmful processes arising from oxidation of the oxygen centers under high operating voltage are recounted. The analysis is concluded with a commentary on further research directions toward optimizing the oxygen activity for high-capacity charge storage.

25 ENERGY STORAGE↗
DOE OSTI2020

Effect of heat treatment on microstructural evolution and hardness homogeneity in laser powder bed fusion of alloy 718

The thermal history developed in laser powder bed fusion (LPBF) processes has been shown to be complex resulting in equally complex microstructures and mechanical properties. Microscopic observations and Vickers micro-hardness mapping measurements were carried out on diff ;erent section planes of LPBF alloy 718 cuboids. Three-dimensional finite element analysis was used to simulate thermal history and to predict the residual stress distribution in the as-built material. Computational thermodynamics was used to predict the micro-segregation and nucleation driving force of various phases in the bulk and in segregated regions. Varied heat-treatments such as simulated hot isostatic pressing, and double aging were applied. Their influence on the microstructure, microsegregation, precipitate formation, and micro-hardness variations of LPBF alloy 718 were investigated. Hardness map results showed heterogeneous micro-hardness on the xy- and xz-planes of the as-built parts where the bottom plane and center regions had larger hardness of ~315 HV 0.5 while the top plane and contours showed hardness of ~300 HV 0.5 . It was found that the aging treatment increased the overall hardness of the as-built condition from ~310 HV 0.5 to 470 HV 0.5 but also increased the hardness gradient throughout the coupon. After simulated hot isostatic pressing process (i.e., without applied pressure) at 1020 °C for 4 h followed by water quench (HIPWQ), the hardness gradient and hardness was minimized (~210 HV 0.5 ) as the microstructure transitioned from heterogeneous columnar grains in the as-built condition to more uniform recrystallized grains. A double aging treatment was applied to enhance hardness from ~210 HV 0.5 to ~440 HV 0.5 . Finally, HIPWQ followed by double aging produced a homogeneous microstructure and more uniform hardness map with enhanced mechanical properties in LPBF alloy 718 coupons.

36 MATERIALS SCIENCE↗
DOE OSTI2022

An analysis of fluff formation in metallic fuel via data analyzes from EBR-II experiments and BISON fuel code modeling

During the operation of EBR-II, it was found that a highly porous structure (over 40% area fraction) formed at the top of several fuel columns. Previous work has shown that this structure, designated fluff in this paper, contains a significant fraction of fuel elements (e.g., U and Pu) which could potentially impact neutronics. This work aims in analyzing the formation mechanism of this microstructure so its impact can be incorporated into future metallic fuel modeling codes and algorithms. This paper details a preliminary examination into the formation mechanisms of fluff by performing qualitative and statistical analysis of EBR-II experimental data. Additionally, the operating conditions that have the greatest impact on fluff formation were determined based on this data set. Also, BISON fuel code simulations were used to help postulate potential fluff formation mechanisms. From this analysis it was found that the largest contributors to fluff formation were fuel burnup and composition, with fluff formation exhibiting a roughly linear positive correlation with increasing burnup and a negative correlation with increasing Pu content. It was also found that higher pin operating temperatures decreased fluff formation but only for U-10Zr fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Three-dimensional morphology of an ultrafine Al-Si eutectic produced via laser rapid solidification

Al-Si alloys processed by laser rapid solidification yield eutectic microstructures with ultrafine and interconnected fibers. Such fibrous structures have long been thought to bear resemblance to those formed in impurity-doped alloys upon conventional casting. Here, we show that any similarity is purely superficial. By harnessing high-throughput characterization and computer vision techniques, we perform a three-dimensional analysis of the branching behavior of the ultrafine eutectic and compare it against an impurity-modified eutectic as well as a random fractal (as a benchmark). Differences in the branching statistics point to different microstructural origins of the impurity- and quench-modified eutectic. Finally, our quantitative approach is not limited to the data presented here but can be used to extract abstract information from other volumetric datasets, without customization.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Discovering mechanisms for materials microstructure optimization via reinforcement learning of a generative model

Abstract The design of materials structure for optimizing functional properties and potentially, the discovery of novel behaviors is a keystone problem in materials science. In many cases microstructural models underpinning materials functionality are available and well understood. However, optimization of average properties via microstructural engineering often leads to combinatorically intractable problems. Here, we explore the use of the reinforcement learning (RL) for microstructure optimization targeting the discovery of the physical mechanisms behind enhanced functionalities. We illustrate that RL can provide insights into the mechanisms driving properties of interest in a 2D discrete Landau ferroelectrics simulator. Intriguingly, we find that non-trivial phenomena emerge if the rewards are assigned to favor physically impossible tasks, which we illustrate through rewarding RL agents to rotate polarization vectors to energetically unfavorable positions. We further find that strategies to induce polarization curl can be non-intuitive, based on analysis of learned agent policies. This study suggests that RL is a promising machine learning method for material design optimization tasks, and for better understanding the dynamics of microstructural simulations.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Microstructure and properties of a high temperature Al–Ce–Mn alloy produced by additive manufacturing

An Al–10Ce-8Mn (wt%) alloy was designed and fabricated by laser powder bed fusion additive manufacturing (AM). The rapid cooling rates of the AM process produced a refined microstructure with a large fraction of reinforcing intermetallic phases. The tensile properties of the alloy were characterized in the as-fabricated state and following thermal exposure. The properties of the as-fabricated microstructure showed exceptional high-temperature performance and strength retention at elevated temperatures up to 400 °C relative to benchmark wrought Al and AM Al alloy properties. Characterization of the microstructure and thermodynamic modeling of the ternary Al–Ce–Mn system rationalized the solidification and solid-state phase transformations. Finally, analysis of the relevant strengthening mechanisms for both the as-fabricated and thermally exposed conditions was performed.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Intergranular ductile failure of materials with plastically heterogeneous grains

In several precipitation hardened alloys that are susceptible to intergranular ductile failure, precipitation does not always occur uniformly throughout the microstructure, and regions close to grain boundaries may remain precipitate-free. These precipitate-free zones (PFZs) in the material microstructures result in plastically heterogeneous grains, since PFZs are expected to have lower yield strength but higher strain-hardenability compared to the precipitate containing grain interior. Experimentally, the presence of PFZs in precipitation-hardened alloys has been associated with both increase and decrease in materials’ ductility, with or without significant change in the strength. Thus, to understand and rationalize the experimental observations, we have carried out extensive microstructure-based finite element calculations of intergranular ductile failure in materials under tensile loading conditions. In the calculations, both the grain boundaries and PFZs are discretely modeled, and a wide range of the values of yield strength, strain-hardenability and width of PFZs in the material microstructures are analyzed. Our results show that the effects of PFZs on the overall mechanical response of the material strongly depend on the values of yield strength and strain-hardenability of PFZs. Here, there exists an optimum combination of the values of these two parameters that can result in the overall ductility and tensile strength of the material microstructures with PFZs being greater than the microstructures without PFZs.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Physical characterization of fault rocks within the Opalinus Clay formation

Near-surface disposal of radioactive waste in shales is a promising option to safeguard the population and environment. However, natural faults intersecting these geological formations can potentially affect the long-term isolation of the repositories. This paper characterizes the physical properties and mineralogy of the internal fault core structure intersecting the Opalinus Clay formation, a host rock under investigation for nuclear waste storage at the Mont Terri Laboratory (Switzerland). We have performed porosity, density, microstructural and mineralogical measurements in different sections of the fault, including intact clays, scaly clays and fault gouge. Mercury intrusion porosimetry analysis reveal a gouge that has a pore network dominated by nanopores of less than 10 nm, yet a high-porosity (21%) and low grain density (2.62 g/cm 3 ) when compared to the intact rock (14.2%, and 2.69 g/cm 3 ). Thus, a more permeable internal fault core structure with respect to the surrounding rock is deduced. Further, we describe the OPA fault gouge as a discrete fault structure having the potential to act as a preferential, yet narrow, and localized channel for fluid-flow if compared to the surrounding rock. Since the fault gouge is limited to a millimetres-thick structure, we expect the barrier property of the geological formation is almost not affected.

58 GEOSCIENCES↗
DOE OSTI2025

An engineering perspective on evaluating mechanisms governing ductility in pure molybdenum

The United States lacks a stable domestic supply of 99 mTc, a critical medical imaging isotope generated from 99 Mo. Accelerator-based production using 100 Mo targets (aMo) introduces mechanical concerns due to the ductile-to-brittle transition temperature inherent to refractory metals like Mo. This study evaluates the tensile behavior of aMo targets from 25 to 1000 °C, compared to powder-metallurgy-processed natural Mo (PMo) and cast-and-rolled Mo (RMo), both as-received and after 5 ppm O 2 exposure in flowing He. RMo showed superior ductility (7.3% at 25 °C, 48% at 1000 °C) and strength, attributed to its fine, elongated grains and high geometrically necessary dislocation density. PMo exhibited variable ductility (up to 33%), while aMo remained brittle, with a maximum elongation of 10.4% at 600 °C. EBSD analysis revealed weak texture in PMo and aMo, but high defect density in aMo limited dislocation mobility. This work links processing, microstructure, and deformation mechanisms to guide fabrication of ductile refractory targets.

Hyer, Holden C. [Oak Ridge National Laboratory (OR↗
DOE OSTI2020

An Investigation of Liquefaction in Irradiated TRIGA Fuel Exposed to Relatively High Temperatures

This report presents the findings of an investigation into high temperature fuel cladding chemical interactions (FCCI) in Training, Research, Isotopes, General Atomics (TRIGA) fuel rods. A TRIGA fuel-rod core or meat is principally composed of uranium (U) particles dispersed in a zirconium hydride (Zr H) matrix. The fuel is clad in sealed 304SS or Incoloy 800 tubes. At high temperatures, the fuel will interact with the cladding, resulting in FCCI. To investigate the FCCI (in this case, liquefaction), irradiated TRIGA fuel rods were exposed to relatively high temperatures in furnace tests. The tests were performed at different temperatures using segments from an irradiated TRIGA fuel rod at the Hot Fuel Examination Facility located at Idaho National Laboratory (INL). The data from this study is important for developing a better understanding of the performance of U-ZrH fuel type during transient events (e.g., a Loss of Coolant Accident (LOCA) event) that may result in high temperatures while operating a TRIGA reactor. Furnace tests were run for 6 hours at 730, 800, 900, 950, and 1,000°C. One test was run for 12 hours at 950°C. Post-test microstructural characterization was performed on the heat-treated samples using optical metallography to look for evidence of liquefaction. Additionally, microstructural characterization was performed using scanning electron microscopy to investigate the microstructure of the as-irradiated fuel before heat treatment and the microstructural changes that occurred after heat treating for the 730 and 950°C heat treatments for 6 hours. Results of the analysis were compared to those produced during diffusion studies performed using unirradiated TRIGA fuel meat and type 304 stainless steel. A gap is typically present in as-irradiated fuel that limits any possibility for chemical interaction between the fuel and cladding. Optical metallography (OM) was used to identify areas in the specimens heat treated at 950 and 1000°C where fuel and cladding contact was satisfactory for the FCCI to transpire. The bulk of the interaction zones that form due to FCCI developed in the fuel meat and not as much in the cladding. Even in the sample tested at 1,000°C, no evidence was found that gross fuel meat or cladding melting had occurred. Only limited porosity was found in the fuel meat that possibly could have been due to melting of a particular precipitate phase or phases that had formed during FCCI. These results agreed with those reported for the unirradiated diffusion couple studies.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

FY21 Status Report on Creep Rupture Testing at ANL to Support the Development of Alloy 709 Code Case

This report provides an update on the status of the creep rupture testing on the first commercial heat of Alloy 709 in support of the Alloy 709 Code Case development. Creep tests were performed in air on the lever-arm load frames in the Mechanical and Environmental Testing Laboratory at Argonne National Laboratory (ANL). In FY21, the focus was on the age-hardened ESR-1150°C material. Twenty two tests were initiated, among which ten were completed. This report presents the data from the completed tests. Metallographic characterization of the fractured specimens were performed and the results are included. The creep data enabled the preliminary analysis of the creep behavior of this material. The characterization showed the effect of test temperature and stress on the deformation microstructure.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2026

Time at Temperature Experiments on Neutron Irradiated Zircaloy-2 using Conventional & Flash DSC

Dryout events in Boiling Water Reactors (BWRs) are currently treated by NRC regulations as automatic disqualification for continued fuel rod operation, even though this criterion does not account for the rate or duration of power increases, associated changes in material behavior, or the possibility of rewetting. Operational history from Anticipated Operational Occurrences (AOOs) shows that short, transient power excursions often demand only modest heat removal, and industry experience suggests that fuel can briefly enter dryout yet return to safe, stable operation. The lack of detailed understanding of the material response during such events motivates the present series of experiments. This study uses unique and innovative methods to investigate microstructural evolution in irradiated Zircaloy-2 exposed to high temperatures in inert environments. Differential Scanning Calorimetry (DSC) and FlashDSC are combined to build a comprehensive experimental framework capable of identifying the a–ß phase transformation in zirconium and examining defect annealing under steep thermal gradients. FlashDSC enables rapid heating and cooling of Focused Ion Beam (FIB)–prepared large-area lift-outs (LALOs) of irradiated Zircaloy-2 at rates of 1,000 K/s to peak temperatures of 600°C, 750°C, and 900°C. The goal is to determine whether these conditions produce measurable microstructural changes that could influence cladding performance in typical BWR environments. Microstructural characterization includes quantifying dislocation density and assessing secondary phase particle (SPP) size and distribution using Transmission Electron Microscopy (TEM). Ongoing analysis, such as diffraction pattern indexing and 4D STEM processing, will further refine these observations.

36 - MATERIALS SCIENCE↗