Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “higher form”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
NASA NTRS2000

Evaluation of an Impedance Model for Perforates Including the Effect of Bias Flow

A new bias flow impedance model is developed for perforated plates from basic principles using as little empiricisms as possible. A quality experimental database was used to determine the predictive validity of the model. Results show that the model performs better for higher (15%) rather than lower (5%) percent open area (POA) samples. Based on the least squares ratio of numerical vs. experimental results, model predictions were on average within 20% and 30% for the higher and lower (POA), respectively. It is hypothesized on the work of other investigators that at lower POAs the higher fluid velocities in the perforate's orifices start forming unsteady vortices, which is not accounted for in our model. The numerical model, in general also underpredicts the experiments. It is theorized that the actual acoustic C(sub D) is lower than the measured raylometer C(sub D) used in the model. Using a larger C(sub D) makes the numerical model predict lower impedances. The frequency domain model derived in this paper shows very good agreement with another model derived using a time domain approach.

Betts, J. F.↗
NASA NTRS2014

Processing and Material Characterization of Continuous Basalt Fiber Reinforced Ceramic Matrix Composites Using Polymer Derived Ceramics.

The need for high performance vehicles in the aerospace industry requires materials which can withstand high loads and high temperatures. New developments in launch pads and infrastructure must also be made to handle this intense environment with lightweight, reusable, structural materials. By using more functional materials, better performance can be seen in the launch environment, and launch vehicle designs which have not been previously used can be considered. The development of high temperature structural composite materials has been very limited due to the high cost of the materials and the processing needed. Polymer matrix composites can be used for temperatures up to 260C. Ceramics can take much higher temperatures, but they are difficult to produce and form in bulk volumes. Polymer Derived Ceramics (PDCs) begin as a polymer matrix, allowing a shape to be formed and cured and then to be pyrolized in order to obtain a ceramic with the associated thermal and mechanical properties. The use of basalt in structural and high temperature applications has been under development for over 50 years, yet there has been little published research on the incorporation of basalt fibers as a reinforcement in the composites. In this study, continuous basalt fiber reinforced PDCs have been fabricated and tested for the applicability of this composite system as a high temperature structural composite material. The oxyacetylene torch testing and three point bend testing have been performed on test panels and the test results are presented.

Polymer Derived Ceramics↗
NASA NTRS2014

Processing and Characterization of Basalt Fiber Reinforced Ceramic Composites for High Temperature Applications Using Polymer Precursors

The development of high temperature structural composite materials has been very limited due to the high cost of the materials and the processing needed. Ceramics can take much higher temperatures, but they are difficult to produce and form in bulk volumes. Polymer Derived Ceramics (PDCs) begin as a polymer matrix, allowing a shape to be formed, to be cured, and be pyrolized in order to obtain a ceramic with the associated thermal and mechanical properties. The two PDCs used in this development are polysiloxane and polycarbosilane. Polysiloxanes contain a silicon oxycarbide backbone when pyrolized up to 1000degC. Polycarbosilane, an organosilicon polymer, contain a silicon-carbon backbone; around 1200degC, -SiC begins to crystallize. The use of basalt in structural and high temperature applications has been under development for over 50 years, yet there has been little published research on the incorporation of basalt fibers as a reinforcement in composites. Basalt is a naturally occurring material found in volcanic rock. Continuous basalt fiber reinforced PDCs have been fabricated and tested for the applicability of this composite system as a high temperature structural composite material. Testing for this included thermal and mechanical testing per ASTM standard tests.

High Temperature Composites↗
NASA NTRS2014

Processing and Characterization of Basalt Fiber Reinforced Ceramic Composites for High Temperature Applications Using Polymer Precursors

The development of high temperature structural composite materials has been very limited due to the high cost of the materials and the processing needed. Ceramics can take much higher temperatures, but they are difficult to produce and form in bulk volumes. Polymer Derived Ceramics (PDCs) begin as a polymer matrix, allowing a shape to be formed and cured and then to be pyrolized in order to obtain a ceramic with the associated thermal and mechanical properties. The two PDCs used in this development are polysiloxane and polycarbosilane. Polysiloxanes contain a silicon oxycarbide backbone when pyrolized up to 1000C. Polycarbosilane, an organosilicon polymer, contain a silicon-carbon backbone; around 1200C, beta-SiC begins to crystallize. The use of basalt in structural and high temperature applications has been under development for over 50 years, yet there has been little published research on the incorporation of basalt fibers as a reinforcement in composites. Basalt is a naturally occurring material found in volcanic rock. Continuous basalt fiber reinforced PDCs have been fabricated and tested for the applicability of this composite system as a high temperature structural composite material. Thermal and mechanical testing includes oxyacetylene torch testing and three point bend testing.

Ceramic Matrix Composites↗
NASA NTRS2014

Processing and Characterization of Basalt Fiber Reinforced Ceramic Composites for High Temperature Applications Using Polymer Precursors

The development of high temperature structural composite materials has been very limited due to the high cost of the materials and the processing needed. Ceramics can take much higher temperatures, but they are difficult to produce and form in bulk volumes. Polymer Derived Ceramics (PDCs) begin as a polymer matrix, allowing a shape to be formed and cured and then to be pyrolized in order to obtain a ceramic with the associated thermal and mechanical properties. The two PDCs used in this development are polysiloxane and polycarbosilane. Polysiloxanes contain a silicon oxycarbide backbone when pyrolized up to 1000 deg C. Polycarbosilane, an organosilicon polymer, contain a silicon-carbon backbone; around 1200 deg C, Beta-SiC begins to crystallize. The use of basalt in structural and high temperature applications has been under development for over 50 years, yet there has been little published research on the incorporation of basalt fibers as a reinforcement in composites. Basalt is a naturally occurring material found in volcanic rock. Continuous basalt fiber reinforced PDCs have been fabricated and tested for the applicability of this composite system as a high temperature structural composite material. Thermal and mechanical testing includes oxyacetylene torch testing and three point bend testing.

Polymer Derived Ceramics↗
NASA NTRS1960

Aerodynamic Characteristics at Mach Numbers of 1.41 and 2.01 of a Series of Cranked Wings Ranging in Aspect Ratio from 4.00 to 1.74 in Combination with a Body

A program has been conducted in the Langley 4- by 4-foot supersonic pressure tunnel to determine the effects of certain wing plan-form variations on the aerodynamic characteristics of wing-body combinations at supersonic speeds. The present report deals with the results of tests of a family of cranked wing plan forms in combination with an ogive-cylinder body of revolution. Tests were made at Mach numbers of 1.41 and 2.01 at corresponding values of Reynolds number per foot of 3.0 x 10(exp 6) and 2.5 x 10(exp 6). Results of the tests indicate that the best overall characteristics were obtained with the low-aspect-ratio wings. Plan-form changes which involved decreasing the aspect ratio resulted in higher values of maximum lift-drag ratio, in addition to large increases in wing volume. Indications are that this trend would have continued to exist at aspect ratios even lower than the lowest considered in the present tests. Increases in the maximum lift-drag ratio of about 15 percent over the basic wing were achieved with practically no increase in drag. The severe longitudinal stability associated with the basic cranked wing was no longer present (within the limits of the present tests) on the wings of lower aspect ratio formed by sweeping forward the inboard portion of the trailing edge.

Sevier, John R., Jr.↗
DOE OSTI2022

Universal Properties of Weakly Bound Two-Neutron Halo Nuclei

We construct an effective field theory of a two-neutron halo nucleus in the limit where the two-neutron separation energy B and the neutron-neutron two-body virtual energy ε n are smaller than any other energy scale in the problem, but the scattering between the core and a single neutron is not fine-tuned, and the Efimov effect does not operate. The theory has one dimensionless coupling which formally runs to a Landau pole in the ultraviolet. We show that many properties of the system are universal in the double fine-tuning limit. The ratio of the mean-square matter radius and charge radius is found to be < r$^{2}_{m}$ > / < r$^{2}_{c}$ > = Af(ε n /B), where A is the mass number of the core and f is a function of the ratio ε n / B which we find explicitly. In particular, when B >> ε n , < r$^{2}_{m}$ > / < r$^{2}_{c}$ > = 2/3 A . Here, the shape of the E1 dipole strength function also depends only on the ratio ε n /B and is derived in explicit analytic form. We estimate that for the 22 C nucleus higher-order corrections to our theory are of the order of 20% or less if the two-neutron separation energy is less than 100 keV and the s-wave scattering length between a neutron and a 20 C nucleus is less than 2.8 fm.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2026

The porosity surrounding carbides and second phase stringers in monolithic U-10Mo fuel plate after irradiation

Post-irradiation microstructure characterization plays an important role in qualifying the low-enriched uranium (LEU) monolithic U-10 wt%Mo plate-type fuel for United States high-performance research reactors (USHPRRs) program. Inhomogeneous features resulting from manufacturing and irradiation processes, including carbides, second phase stringers, and extensive void spaces caused by the combining of small porosities, may increase the risk of heat concentration in local regions of the fuel plate over the operating conditions. In this study, characteristics of carbides, stringers, and porosity after multiple levels of irradiation at varying fission densities were studied by electron microscopes to decipher the morphology of pores and the porosity evolution in U-10 wt%Mo. For carbides, the result shows that porosities start forming on UMo grain boundaries, then on UMo/carbides interfaces as the burn-up going higher. However, the porosities surrounding carbides grow larger than the ones on UMo grain boundaries. The porosities around the uranium carbides could interconnect to form larger void space. The study revealed that the void spaces larger than 5 µm were found around uranium carbides after high burnup, while no evidence was observed to support the similar voids formed near second phase stringers even though the size of the stringers (> 50 µm) was much larger than uranium carbides (< 20 µm). The evolution of porosities suggests that the formation of second phase stringers may not create more significant porosities compared to regular uranium carbides regions during fuel operating conditions.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1998

Crystallization of Chicken Egg White Lysozyme from Sulfate Salts

It has been "known" that chicken egg white lysozyme does not crystallize from sulfate, particularly ammonium sulfate, salts, but instead gives amorphous precipitates. This has been the basis of several studies using lysozyme comparing macromolecule crystal nucleation and amorphous precipitation. Recently Ries-Kautt et al (Acta Cryst D50, (1994) 366) have shown that purified isoionic CEWL could be crystallized from low concentrations of sulfate at basic pH, and we subsequently showed that in fact CEWL could be purified in both the tetragonal and orthorhombic forms using ammonium sulfate over the pH range 4.0 to 7.8 (Acta Cryst D53, (1997) 795). We have now extended these observations to include a range of common sulfate salts, specifically sodium, potassium, rubidium, magnesium, and manganese sulfates. In all cases but the manganese sulfates both the familiar tetragonal and orthorhombic forms were obtained, with unit cell dimensions close to those known for the "classic" sodium chloride crystallized forms. Manganese sulfate has only yielded orthorhombic crystals to date. All crystallizations were carried out using low (typically less than or equal to 6 M) salt and high (greater than approximately 90 mg/ml) protein concentrations. As with ammonium sulfate, the tetragonal - orthorhombic phase shift appears to be a function of both the temperature and the protein concentration, with higher temperatures and concentrations favoring the orthorhombic and lower the tetragonal form. The phase change range is somewhat reduced for the sulfate salts, depending upon conditions being typically between approximately 15 - 20 C. Both the magnesium and manganese sulfates gave crystals at salt concentrations over 0.6 M as well, with magnesium sulfate giving a very slowly nucleating and growing hexagonal form. A triclinic crystal form, characterized by aggressively small crystals (typically 0.1 mm in size) has been occasionally obtained from ammonium sulfate. Finally, preliminary spot solubility determinations have suggested that in some cases the solubility increases with increasing salt concentrations.

Forsythe, Elizabeth↗
NASA NTRS1992

Synoptic maps of heliospheric Thomson scattering brightness from 1974-1985 as observed by the Helios photometers

We display the electron Thomson scattering intensity of the inner heliosphere as observed by the zodiacal light photometers on board the Helios spacecraft in the form of synoptic maps. The technique extrapolates the brightness information from each photometer sector near the Sun and constructs a latitude/longitude map at a given solar height. These data are unique in that they give a determination of heliospheric structures out of the ecliptic above the primary region of solar wind acceleration. The spatial extent of bright, co-rotating heliospheric structures is readily observed in the data north and south of the ecliptic plane where the Helios photometer coverage is most complete. Because the technique has been used on the complete Helios data set from 1974 to 1985, we observe the change in our synoptic maps with solar cycle. Bright structures are concentrated near the heliospheric equator at solar minimum, while at solar maximum bright structures are found at far higher heliographic latitudes. A comparison of these maps with other forms of synoptic data are shown for two available intervals.

Hick, P.↗
NASA NTRS1978

An experimental investigation of the condensation of silicate grains

Results are presented for a series of laboratory experiments designed to investigate the nucleation of small silicate grains from a vapor of astrophysically significant elements and compounds. In the experiments, magnesium silicate grains were condensed by simultaneously evaporating Mg and SiO solids into an atmosphere of argon or hydrogen at a pressure of a few torr. The results show that at low temperatures (up to a few hundred degrees C) the condensates are amorphous grains and have widely varying stoichiometries. The thermodynamically most stable compounds (Mg2SiO4, MgSiO3, SiO2) do not form readily, but all initial condensates can be converted to crystalline forsterite (Mg2SiO4) by heating to 1000 C in vacuum. At higher temperatures (above 700 K) it becomes more difficult to nucleate any silicates, and those that do form are amorphous, indicating that surface energies and kinetic effects are very important in determining under what conditions condensation will occur. The IR spectra of the experimentally produced magnesium silicates are found to have a strong resemblance to those observed in many astronomical clouds.

Day, K. L.↗
NASA NTRS1982

On higher eigenstates of Goertler instability in compressible flow

The effect of secondary instabilities of Goertler vortices with respect to their growth and amplification was investigated. Instability of viscous flow along a concave surface is in the form of counterrotating streamwise vortices commonly known as Goertler vortices. The effects of suction on higher modes of Goertler vortices are also considered.

Goglia, G. L.↗
DOE OSTI2021

Growth, sintering, and chemical states of Co supported on reducible CeO 2 (111) thin films: The effects of the metal coverage and the nature of the support

The growth, sintering, and interaction of cobalt with ceria were studied under ultrahigh vacuum conditions by vapor-deposition of Co onto well-defined CeOx(111) (1.5 < x < 2) thin films grown on Ru(0001). Charge transfer from Co to ceria occurs upon deposition of Co on CeO 1.96 and partially reduced CeO 1.83 at 300 K. X-ray photoelectron spectroscopy studies show that Co is oxidized to Co 2+ species at the cost of the reduction of Ce 4+ to Ce 3+ , at a lesser extent on reduced ceria. Co 2+ is the predominant species on CeO 1.96 at low Co coverages (e.g., ≤0.20 ML). The ratio of metallic Co/Co 2+ increases with the increase in the Co coverage. However, both metallic Co and Co 2+ species are present on CeO 1.83 even at low Co coverages with metallic Co as the major species. Scanning tunneling microscopy results demonstrate that Co tends to wet the CeO 1.96 surface at very low Co coverages at room temperature forming one-atomic layer high structures of Co–O–Ce. The increase in the Co coverage can cause the particle growth into three-dimensional structures. The formation of slightly flatter Co particles was observed on reduced CeO 1.83 . In comparison with other transition metals including Ni, Rh, Pt, and Au, our studies demonstrate that Co on ceria exhibits a smaller particle size and higher thermal stability, likely arising from strong metal–support interactions. The formed particles upon Co deposition at 300 K are present on the ceria surface after heating to 1000 K. The Co–ceria interface can be tuned by varying the Co metal coverage, the annealing temperature, and the nature of the ceria surface.

36 MATERIALS SCIENCE↗
NASA NTRS2013

NASA Marshall Space Flight Center Tri-gas Thruster Performance Characterization

Historically, spacecraft reaction control systems have primarily utilized cold gas thrusters because of their inherent simplicity and reliability. However, cold gas thrusters typically have a low specific impulse. It has been determined that a higher specific impulse can be achieved by passing a monopropellant fluid mixture through a catalyst bed prior to expulsion through the thruster nozzle. This research analyzes the potential efficiency improvements from using tri-gas, a mixture of hydrogen, oxygen, and an inert gas, which in this case is helium. Passing tri-gas through a catalyst causes the hydrogen and oxygen to react and form water vapor, ultimately heating the exiting fluid and generating a higher specific impulse. The goal of this project was to optimize the thruster performance by characterizing the effects of varying several system components including catalyst types, catalyst lengths, and initial catalyst temperatures.

Dorado, Vanessa↗
DOE OSTI2025

Manipulating Excitonic Quantum Droplets in Two-Dimensional CdSe Nanoplatelets via Thickness and Core/Shell Morphology

Recently, photoexcitation of high-density 4 or 5 monolayer (ML) thick CdSe nanoplatelet films at temperatures below ~200K was observed to produce pump-intensitydependent, superlinear, progressively red-shifted light output due to amplified spontaneous emission (ASE) from polyexcitonic species, distinct from biexcitonic ASE. These polyexcitonic species comprise Coulombically bound multiexciton states, termed “quantum droplets”, that form when multiexciton binding energy exceeds thermal energy fluctuations. In this work, we investigate thinner samples as well as core/shell nanoplatelet films and find that the 3 ML sample supports quantum droplet ASE up to higher temperatures than the 4 or 5 ML whereas core/shell structures suppress this form of ASE even at very low sample temperatures despite observable biexcitonic ASE, suggesting that the reduced or repulsive Coulomb binding energy of multiple excitons suppresses quantum droplets. These findings help to add understanding of routes to harness quantum droplet optical nonlinearities.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1976

Zonal and tesseral harmonic coefficients for the geopotential function, from zero to 18th order

Zonal and tesseral harmonic coefficients for the geopotential function are usually tabulated in normalized form to provide immediate information as to the relative significance of the coefficients in the gravity model. The normalized form of the geopotential coefficients cannot be used for computational purposes unless the gravity model has been modified to receive them. This modification is usually not done because the absolute or unnormalized form of the coefficients can be obtained from the simple mathematical relationship that relates the two forms. This computation can be quite tedious for hand calculation, especially for the higher order terms, and can be costly in terms of storage and execution time for machine computation. In this report, zonal and tesseral harmonic coefficients for the geopotential function are tabulated in absolute or unnormalized form. The report is designed to be used as a ready reference for both hand and machine calculation to save the user time and effort.

Kirkpatrick, J. C.↗
DOE OSTI2023

Noise and thermal depinning of Wigner crystals

We examine changes in the depinning threshold and conduction noise fluctuations for driven Wigner crystals in the presence of quenched disorder. At low temperatures there is a well defined depinning threshold and a strong peak in the noise power with 1/f noise characteristics. At higher temperatures, the depinning threshold shifts to lower drives and the noise, which is also reduced in power, becomes more white in character. At lower temperatures, a washboard frequency appears when the system depins elastically or forms a moving smectic state; however, this washboard signal is strongly reduced for higher temperatures and completely disappears above the melting temperature of a system without quenched disorder. Our results are in good agreement with recent transport and noise studies for systems where electron crystal depinning is believed to arise, and also show how noise can be used to distinguish between crystal, glass, and liquid phases.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS2006

Formation of Metal and Silicate Globules in Gujba: A New Bencubbin-like Meteorite Fall

Gujba is a coarse-grained meteorite fall composed of 41 vol% large kamacite globules, 20 vol% large light-colored silicate globules with cryptocrystalline, barred pyroxene and barred olivine textures, 39 vol% dark-colored, silicate-rich matrix, and rare refractory inclusions. Gujba resembles Bencubbin and Weatherford in texture, oxygen-isotopic composition and in having high bulk delta N-15 values (approximately +685%0). The He-3 cosmic-ray exposure age of Gujba (26 +/- 7 Ma) is essentially identical to that of Bencubbin, suggesting that they were both reduced to meter-size fragments in the same parent-body collision. The Gujba metal globules exhibit metal-troilite quench textures and vary in their abundances of troilite and volatile siderophile elements. We suggest that the metal globules formed as liquid droplets either via condensation in an impact-generated vapor plume or by evaporation of preexisting metal particles in a plume. The lower the abundance of volatile elements in the metal globules, the higher the globule quench temperature. We infer that the large silicate globules also formed from completely molten droplets; their low volatile-element abundances indicate that they also formed at high temperatures, probably by processes analogous to those that formed the metal globules. The coarse-grained Bencubbin-Weatherford-Gujba meteorites may represent a depositional component from the vapor cloud enriched in coarse and dense particles. A second class of Bencubbin-like meteorites (represented by Hammadah a1 Hamra 237 and QUE 94411) may be a finer fraction derived from the same vapor cloud

Rubin, Alan E.↗