Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “generative diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Surface Properties and RF Performance of Vapor Diffused Nb3Sn on NB After Sequential Anneals Below 1000°C

Nb3Sn is a next-generation superconducting material that can be used for future superconducting radiofrequency (SRF) accelerator cavities, promising better performance, cost reduction, and higher operating temperature than Nb. The Sn vapor diffusion method is currently the most preferred and successful technique to coat niobium cavi-ties with Nb3Sn. Among post-coating treatments to opti-mize the coating quality, higher temperature annealing without Sn is known to degrade Nb3Sn because of Sn loss. We have investigated Nb3Sn/Nb samples briefly annealed at 800-1000°C for 10 and 20 minutes to poten-tially improve the surface to enhance the performance of Nb3Sn-coated cavities. Following the sample studies, a coated single-cell cavity was sequentially annealed at 900°C and tested its performance each time, improving the cavity's quality factor relatively. This paper summarizes the sample studies and discusses the RF test results from sequentially annealed SRF Nb3Sn/Nb cavity.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2021

Deep potential generation scheme and simulation protocol for the Li 10 GeP 2 S 12 -type superionic conductors

We report solid-state electrolyte materials with superior lithium ionic conductivities are vital to the next-generation Li-ion batteries. Molecular dynamics could provide atomic scale information to understand the diffusion process of Li-ion in these superionic conductor materials. Here, we implement the deep potential generator to set up an efficient protocol to automatically generate interatomic potentials for Li 10 GeP 2 S 12 -type solid-state electrolyte materials (Li 10 GeP 2 S 12 , Li 10 SiP 2 S 12 , and Li 10 SnP 2 S 12 ). The reliability and accuracy of the fast interatomic potentials are validated. With the potentials, we extend the simulation of the diffusion process to a wide temperature range (300 K–1000 K) and systems with large size (~1000 atoms). Important technical aspects such as the statistical error and size effect are carefully investigated, and benchmark tests including the effect of density functional, thermal expansion, and configurational disorder are performed. The computed data that consider these factors agree well with the experimental results, and we find that the three structures show different behaviors with respect to configurational disorder. Our work paves the way for further research on computation screening of solid-state electrolyte materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2001

Forced Diffusion of Trailing Vorticity from a Hovering Rotor

A small turbulence generating device was Attached near the tip of a hovering rotor blade In order to alter the structure of the trailing vortex. Stereo particle image velocimetry (PIV) images were used to quantify the wake behind the rotor blade during the first revolution. An analysis of the 3D-velocity field includes a method for accounting for vortex wander. The results show that a major change in the size and intensity of the trailing vortex can be achieved.

McAlister, Kenneth W.↗
DOE OSTI2012

Diffusion Welding of Compact Heat Exchangers for Nuclear Applications

The next-­-generation nuclear plant (NGNP) is designed to be a flexible source of energy, producing various mixes of electrical energy and process heat (for example, for hydrogen generation) on demand. Compact heat exchangers provide an attractive way to move energy from the helium primary reactor coolant to process heat uses. For process heat efficiency, reactor outlet temperatures of 750-­-900°C are desirable. There are minor but deleterious components in the primary coolant; the number of alloys that can handle this environment is small. The present work concentrates on Alloys 800H and 617.

42 ENGINEERING↗
DOE OSTI2024

Interpenetrated Structures for Enhancing Ion Diffusion Kinetics in Electrochemical Energy Storage Devices

The architectural design of electrodes offers new opportunities for next-generation electrochemical energy storage devices (EESDs) by increasing surface area, thickness, and active materials mass loading while maintaining good ion diffusion through optimized electrode tortuosity. However, conventional thick electrodes increase ion diffusion length and cause larger ion concentration gradients, limiting reaction kinetics. We demonstrate a strategy for building interpenetrated structures that shortens ion diffusion length and reduces ion concentration inhomogeneity. This free-standing device structure also avoids short-circuiting without needing a separator. The feature size and number of interpenetrated units can be adjusted during printing to balance surface area and ion diffusion. Starting with a 3D-printed interpenetrated polymer substrate, we metallize it to make it conductive. This substrate has two individually addressable electrodes, allowing selective electrodeposition of energy storage materials. Using a Zn//MnO 2 battery as a model system, the interpenetrated device outperforms conventional separate electrode configurations, improving volumetric energy density by 221% and exhibiting a higher capacity retention rate of 49% compared to 35% at temperatures from 20 to 0 °C. Our study introduces a new EESD architecture applicable to Li-ion, Na-ion batteries, supercapacitors, etc.

25 ENERGY STORAGE↗
DOE OSTI2023

Data-driven methods for diffusivity prediction in nuclear fuels

The growth rate of structural defects in nuclear fuels under irradiation is intrinsically related to the diffusion rates of the defects in the fuel lattice. The generation and growth of atomistic structural defects can significantly alter the performance characteristics of the fuel. This alteration of functionality must be accurately captured to qualify a nuclear fuel for use in reactors. Predicting the diffusion coefficients of defects and how they impact macroscale properties such as swelling, gas release, and creep is therefore of significant importance in both the design of new nuclear fuels and the assessment of current fuel types. In this article, we apply data-driven methods focusing on machine learning (ML) to determine various diffusion properties of two nuclear fuels—uranium oxide and uranium nitride. We show that using ML can increase, often significantly, the accuracy of predicting diffusivity in nuclear fuels in comparison to current analytical models. We also illustrate how ML can be used to quickly develop fuel models with parameter dependencies that are more complex and robust than what is currently available in the literature. In conclusion, these results suggest there is potential for ML to accelerate the design, qualification, and implementation of nuclear fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Improving generative model-based unfolding with Schrödinger bridges

Machine learning-based unfolding has enabled unbinned and high-dimensional differential cross section measurements. Two main approaches have emerged in this research area; one based on discriminative models and one based on generative models. The main advantage of discriminative models is that they learn a small correction to a starting simulation while generative models scale better to regions of phase space with little data. We propose to use Schrödinger bridges and diffusion models to create , an unfolding approach that combines the strengths of both discriminative and generative models. The key feature of is that its generative model maps one set of events into another without having to go through a known probability density as is the case for normalizing flows and standard diffusion models. We show that achieves excellent performance compared to state of the art methods on a synthetic Z + jets dataset. Published by the American Physical Society 2024

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2020

Field-emission plasma enhancement of H₂–O₂ micro-combustion

In this paper, a detailed three-dimensional computational model is developed to assess the potential of micron-scale field emission dielectric barrier discharge (FE-DBD) plasma actuators in non-premixed microburners with channel heights in the range of L z = 0.25–0.75 mm. Results for H 2 –O 2 combustion with Reynolds number Re = 100 are studied for different configurations of plasma actuator arrays. Without plasma actuation, results agree with corresponding experiments, although in this case the burner typically suffers from incomplete combustion due to thermal quenching, radical quenching, and slow diffusive mixing. For the range of conditions simulated, plasma actuation increases combustion completeness from 25%–70% to 40%–80% by enhancing mixing, generating radicals, and Joule heating. Ionic wind resulting from the FE-DBD plasma disrupts the otherwise simple laminar flow in the burner, accelerating the growth of a mixing layer and enhancing heat transfer to channel walls. The larger, lower temperature flames reduce thermal gradients (and thereby thermal stresses) in the walls. Radical generation due to electron-impact dissociation extends the reaction zone in the diffusion flame and increases combustion completeness. In all cases, the additional heat release with plasma actuation (100–190 W) is significantly larger than the power needed to sustain the plasma (≲0.1 W), suggesting that plasma actuation may provide a significant advantage in energy generation using realistic portable micro-combustion devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2015

Kinetic Monte Carlo Simulation of Oxygen Diffusion in Ytterbium Disilicate

Silicon-based ceramic components for next-generation jet turbine engines offer potential weight savings, as well as higher operating temperatures, both of which lead to increased efficiency and lower fuel costs. Silicon carbide (SiC), in particular, offers low density, good strength at high temperatures, and good oxidation resistance in dry air. However, reaction of SiC with high-temperature water vapor, as found in the hot section of jet turbine engines in operation, can cause rapid surface recession, which limits the lifetime of such components. Environmental Barrier Coatings (EBCs) are therefore needed if long component lifetime is to be achieved. Rare earth silicates such as Yb2Si2O7 and Yb2SiO5 have been proposed for such applications; in an effort to better understand diffusion in such materials, we have performed kinetic Monte Carlo (kMC) simulations of oxygen diffusion in Ytterbium disilicate, Yb2- Si2O7. The diffusive process is assumed to take place via the thermally activated hopping of oxygen atoms among oxygen vacancy sites or among interstitial sites. Migration barrier energies are computed using density functional theory (DFT).

Computer Simulation↗
DOE OSTI2016

Multicomponent diffusion in molten salt NaF-ZrF{sub 4}: Dynamical correlations and Maxwell–Stefan diffusivities

NaF-ZrF{sub 4} is used as a waste incinerator and as a coolant in Generation IV reactors.Structural and dynamical properties of molten NaF-ZrF{sub 4} system were studied along with Onsagercoefficients and Maxwell–Stefan (MS) Diffusivities applying Green–Kubo formalism and molecular dynamics (MD) simulations. The zirconium ions are found to be 8 fold coordinated with fluoride ions for all temperatures and concentrations. All the diffusive flux correlations show back-scattering. Even though the MS diffusivities are expected to depend very lightly on the composition because of decoupling of thermodynamic factor, the diffusivity Đ{sub Na-F} shows interesting behavior with the increase in concentration of ZrF{sub 4}. This is because of network formation in NaF-ZrF{sub 4}. Positive entropy constraints have been plotted to authenticate negative diffusivities observed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2014

Direct molecular diffusion and micro-mixing for rapid dewatering of LiBr solution

A slow molecular diffusion rate often limits the desorption process of an absorbate molecule from a liquid absorbent. To enhance the desorption rate, the absorbent is often boiled to increase the liquid vapor interfacial area. However, the growth of bubbles generated during the nucleate boiling process still remains mass-diffusion limited. Here, it is shown that a desorption rate higher than that of boiling can be achieved, if the vapor absorbent interface is continuously replenished with the absorbate-rich solution to limit the concentration boundary layer growth. The study is conducted in a LiBr-water-solution, in which the water molecules' diffusion rate is quite slow. The manipulation of the vapor solution interface concentration distribution is enabled by the mechanical confinement of the solution flow within microchannels, using a hydrophobic vapor-venting membrane and the implementation of microstructures on the flow channel's bottom wall. The microstructures stretch and fold the laminar streamlines within the solution film and produce vortices. The vortices continuously replace the concentrated solution at the vapor solution interface with the water-rich solution brought from the bottom and middle of the flow channel. The physics of the process is described using a combination of experimental and numerical studies. Published by Elsevier Ltd.

Bigham, S↗
DOE OSTI2022

CEFR simulation using diffusion code system RAST-F

In this study, the RAST-F code system, which is based on the two-step approach that couples a multi-group cross-section generation Monte-Carlo (MC) code and a multi-group nodal diffusion solver, was used for the neutronic simulation of the CEFR start-up experiments. The numerical solution of the RAST-F system was verified against the full core MC solution MCS at all control rods fully inserted and withdrawn states. The RAST-F solution of the selected experimental simulations was compared against the measurement data. A good agreement between RAST-F and MCS solutions was observed with less than 120 pcm discrepancies and 1.2% root-mean-square error in terms of k{sub eff} and power distribution, respectively. Meanwhile, the RAST-F result agreed well with the experimental data within two-sigma of experimental uncertainty. The good agreement of these results indicates that RAST-F can be used to neutronic steady-state simulations for small core-size SFR, which was challenged to deterministic code systems. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
NASA NTRS1998

Time-resolved diffusion tomographic imaging in highly scattering turbid media

A method for imaging objects in highly scattering turbid media. According to one embodiment of the invention, the method involves using a plurality of intersecting source/detectors sets and time-resolving equipment to generate a plurality of time-resolved intensity curves for the diffusive component of light emergent from the medium. For each of the curves, the intensities at a plurality of times are then inputted into the following inverse reconstruction algorithm to form an image of the medium: X.sup.(k+1).spsp.T =?Y.sup.T W+X.sup.(k).spsp.T .LAMBDA.!?W.sup.T W+.LAMBDA.!.sup.-1 wherein W is a matrix relating output at detector position r.sub.d, at time t, to source at position r.sub.s, .LAMBDA. is a regularization matrix, chosen for convenience to be diagonal, but selected in a way related to the ratio of the noise, to fluctuations in the absorption (or diffusion) X.sub.j that we are trying to determine: .LAMBDA..sub.ij =.lambda..sub.j .delta..sub.ij with .lambda..sub.j = /<.DELTA.Xj.DELTA.Xj> Here Y is the data collected at the detectors, and X.sup.k is the kth iterate toward the desired absoption information.

Alfano, Robert R.↗
DOE OSTI2018

Pore-scale study of effects of macroscopic pores and their distributions on reactive transport in hierarchical porous media

For applications of reactive transport in porous media, optimal porous structures should possess both high surface area for reactive sites loading and low mass transport resistance. Hierarchical porous media with a combination of pores at different scales are designed for this purpose. In this paper, using the lattice Boltzmann method, pore-scale numerical studies are conducted to investigate diffusion-reaction processes in 2D hierarchical porous media generated by self-developed reconstruction scheme. Complex interactions between porous structures and reactive transport are revealed under different conditions. Simulation results show that adding macropores can greatly enhance the mass transport, but at the same time reduce the reactive surface, leading to complex change trend of the total reaction rate. Effects of gradient distribution of macropores within the porous medium are also investigated. It is found that a front-loose, back-tight (FLBT) hierarchical structure is desirable for enhancing mass transport, increasing total reaction rate, and improving catalyst utilization. Finally, on the whole, from the viewpoint of reducing cost and improving material performance, hierarchical porous structures, especially gradient structures with the size of macropores gradually decreasing along the transport direction, are desirable for catalyst application.

42 ENGINEERING↗
DOE OSTI2022

Silicon alloying enhances fast heating rate combustion of aluminum particles

Alloys and composites of aluminum (Al) have shown promise in regulating and enhancing particle combustion for energy generation applications. Recent work on aluminum-silicon (Al-Si) spherical alloy particles has shown improved combustion at low heating rates through enhanced diffusion accompanying a lower melting temperature. This study extends reactivity analysis to higher heating rates, comparing oxidation of Al-Si with Al. Flame speeds of Al-Si powder mixed with molybdenum trioxide (MoO 3 ) powder (Al-Si+MoO 3 ) exhibited a faster transition to steady propagation relative to Al+MoO 3 . Bomb calorimetry experiments revealed up to 5.8% greater early temperature rise for Al-Si powder. Rapid steady propagation for Al-Si mixture and faster temperature rise for Al-Si particles were attributed to accelerated kinetics evidenced in thermal equilibrium analysis of the mixtures using a differential scanning calorimeter (DSC). Larger DSC exotherms in the early stages of oxidation (i.e., 480–720 °C) correlated with early heat release and promoted steady flame propagation for Al-Si+MoO 3 compared with Al+MoO 3 . Furthermore, in multiple heating rate DSC studies, Al-Si+MoO 3 ignited at a lower heating rate (i.e., 15 ⁰C/min) than Al+MoO 3 (i.e., 20 ⁰C/min). Both mixtures ignited at temperatures less than 625 °C which is above the melting temperature of Al-Si (574 °C) and below Al (659 °C). Thus, alloy particle fuels with enhanced diffusion-controlled kinetics promote steady flame propagation and show promise for energy generation applications. This is especially promising for technologies driven by enhanced condensed phase combustion such as some propellant additives or applications dependent on reliable burn rates such as pyrotechnic time delay formulations and primers.

36 MATERIALS SCIENCE↗
DOE OSTI2013

In situ CrB{sub 2} and its effect on the mechanical properties of A390 alloy

In this work, a series of CrB{sub 2}/A390 composite alloys have been prepared and analyzed by a field emission scanning electron microscope (FESEM) and X-ray diffraction (XRD). Firstly, in situ CrB{sub 2} has been prepared by reducing reaction that occurred in Al melt: AlB{sub 2} + [Cr] → Al + CrB{sub 2}. The CrB{sub 2} particles exhibit regular hexagonal platelet morphology and distribute uniformly in the Al matrix. Then, A390 alloys with different CrB{sub 2} additions have been prepared. With the addition of CrB{sub 2}, the size of primary Si can be reduced remarkably. The generation of CrB{sub 2} particles and their diffuse distribution can improve the mechanical properties of A390 alloy obviously. The mechanical properties of the base alloy, including ultimate tensile strength at 25 °C (UTS{sub 25°C}), the coefficient of thermal expansion (CTE) and wear resistance have been studied and the composite alloy with 3 wt.% CrB{sub 2} particle addition showed the best performance. - Highlights: • CrB2/A390 composite alloy was successfully fabricated at 850 °C. • The reaction between AlB2 and Cr was investigated. • The possible coherent interface of CrB2 and Si was calculated. • Mechanical properties of A390 alloy are improved with the addition of CrB2.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Size-controllable fabrication of Cu nanoparticles on carbon nanotubes by simple heating

Highlights: • Cu nanoparticles were synthesized on the surface of carbon nanotubes by heating. • The particle size could be tuned by controlling the temperature and duration. • The possible nucleation and growth mechanisms of nanoparticles were discussed. - Abstract: In this paper, employing simple heating inside the transmission electron microscope, we demonstrated the decoration of carbon nanotubes (CNTs) by Cu nanoparticles (NPs). More significantly, the particle sizes could be effectively controlled by simply controlling the temperature and duration. It is believed that the nucleation and growth of NPs results from the deposition of generated Cu vapor as well as the surface diffusion of Cu on the CNTs at elevated temperature.

36 MATERIALS SCIENCE↗