Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “flaps”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Unsteady wake effects on progressing/regressing forced rotor flapping modes.

A two bladed 16 inch hingeless rotor model was built and tested outside and inside a 24 by 24 inch wind tunnel test section at collective pitch settings up to 5 deg and rotor advance ratios up to .4. The rotor model has a simple excentric mechanism to provide progressing or regressing cyclic pitch excitation. The flapping responses were compared to analytically determined responses which included flap-bending elasticity but excluded rotor wake effects. Substantial systematic deviations of the measured responses from the computed responses were found, which were interpreted as the effects of interaction of the blades with a rotating asymmetrical wake.

Hohenemser, K. H.↗
NASA NTRS1972

Experimental Hingeless Rotor Characteristics at Full Scale First Flap Mode Frequencies (including Rotor Frequency Response to Shaft Oscillations), Phase 3

The completion of the High Advance Ratio Research Program is reported. The primary objectives of the program were to experimentally determine the rotor frequency response to shaft pitching and rolling oscillations and to acquire steady response and frequency response data at high advance ratios for hingeless rotors with typical, full-scale, first flap mode natural frequencies. Secondary objectives of the program included the further evaluation of both the hub moment feedback control system and the simplified rigid blade flapping theory with respect to shaft oscillations. The bulk of the text is devoted to the presentation and examination of representative experimental results. All the analyzed test data are documented in tabular and/or graphical formats.

Kuczynski, W. A.↗
NASA NTRS1972

Flight tests of a rotating cylinder flap on a North American Rockwell YOV-10 aircraft

Flight tests were conducted of a twin engine airplane modified to a STOL configuration with rotating cylinder flaps and interconnected propellers. The flight tests included verification of the functional operation of the rotating cylinder flap system and the determination of the low speed flying qualities and performance characteristics with emphasis on approach and landing.

Cichy, D. R.↗
NASA NTRS1973

Analysis of high-aspect-ratio jet-flap wings of arbitrary geometry

An analytical technique to compute the performance of an arbitrary jet-flapped wing is developed. The solution technique is based on the method of Maskell and Spence in which the well-known lifting-line approach is coupled with an auxiliary equation providing the extra function needed in jet-flap theory. The present method is generalized to handle straight, uncambered wings of arbitrary planform, twist, and blowing (including unsymmetrical cases). An analytical procedure is developed for continuous variations in the above geometric data with special functions to exactly treat discontinuities in any of the geometric and blowing data. A rational theory for the effect of finite wing thickness is introduced as well as simplified concepts of effective aspect ratio for rapid estimation of performance.

Lissaman, P. B. S.↗
NASA NTRS1973

A simulator investigation of the influence of engine response characteristics on the approach and landing for an externally blown flap aircraft. Part 2: Aerodynamic model

An analysis of the influence of engine response characteristics on the approach and landing of an externally blown flap aircraft was conducted using flight simulator facilities. The configuration of the aerodynamic model is described. The aerodynamic characteristics as a function of angle of attack, thrust coefficient, and flap deflection are presented in tabular form and as graphs.

Ciffone, D. L.↗
NASA NTRS1973

Analytical study of takeoff and landing performance for a jet STOL transport configuration with full-span, externally blown, triple-slotted flaps

Takeoff and landing performance characteristics and field length requirements were determined analytically for a jet STOL transport configuration with full-span, externally blown, tripleslotted flaps. The configuration had a high wing, high T-tail, and four pod-mounted high-bypass-ratio turbofan engines located under and forward of the wing. One takeoff and three approach and landing flap settings were evaluated. The effects of wing loading, thrust-to-weight ratio, weight, ambient temperature, altitude on takeoff and landing field length requirements are discussed.

Washington, H. P.↗
NASA NTRS1972

Stability and control of externally blown flap configurations

The results of wind-tunnel investigations on the stability and control characteristics of externally blown jet-flap configurations are presented. Conventional wind-tunnel tests and free-flight model tests have shown that longitudinal trim and stability can be achieved by a properly located horizontal tail of sufficient size, and that lateral trim in the engine-out condition can be produced by combinations of differential flap, spoiler, and rudder deflection. Free-flight model tests have revealed a lightly damped Dutch roll lateral oscillation, and have shown that the oscillation can be stabilized by use of artificial damping.

Parlett, L. P.↗
NASA NTRS1972

Simulator evaluation of the flying qualities of externally blown flap and augmentor wing transport configurations

Concurrent simulations of powered-lift STOL transport aircraft having either an externally blown flap configuration or an augmentor wing configuration were conducted. The following types of simulators of varying sophistication were used: (1) a simple fixed-base simulation with a simple visual display, (2) a more complex fixed-base simulation using a realistic transport cockpit and a high-quality visual display, and (3) a six-degree-of-freedom motion simulator that had a realistic transport cockpit and a sophisticated visual display. The unaugmented flying qualities determined from these simulations were rated as unacceptable for both the externally blown flap and augmentor wing configurations. The longitudinal, lateral-directional, and single-engine-failure characteristics were rated satisfactory with extensive augmentation, including pitch and roll command systems, flight-path (or speed) augmentation, turn coordination, and effective yaw damping. However, the flare and landing characteristics from any approach glide-path angle in excess of 4 deg were rated as unsatisfactory but acceptable.

Kier, D. A.↗
NASA NTRS1972

Flap noise generation and control

The characteristics of aerodynamic noise generated by the interaction of an airstream with a flap surface are discussed. The location and behavior of various noise sources were investigated to determine optimal quieting techniques. A schematic diagram of the jet-flap concepts being considered for integrated-powered-lift systems for short takeoff aircraft is shown. Each of the concepts has in common high velocity turbulent air flowing over relatively rigid surfaces with resultant production of interaction noise. The nature, location, and control of noise sources which involve the interactions of air flows with airfoil surfaces are examined.

Chestnutt, D.↗
NASA NTRS1973

A flight study of the use of direct-lift-control flaps to improve station keeping during in-flight refueling

To investigate the effectiveness of fast-acting flaps as direct-lift-control (DLC) devices on a fighter airplane, the aileron servo systems of an F-100C variable-stability airplane were modified to provide symmetrical actuation of the surfaces. Initial flight tests using DLC indicated that the task of formation flying and, hence, in-flight refueling could be eased by actuating the DLC flaps through the conventional control stick, with the degree of improvement depending on the basic stability of the receiver aircraft. Results of refueling approaches and connections with U.S. Air Force tankers indicated a moderate overall improvement in vertical station-keeping performance (approximately 19 percent) and a sizeable overall decrease in receiver airplane motions and control activity (approximately 40 percent) with DLC.

Mcneill, W. E.↗
NASA NTRS1973

Analysis of high aspect ratio jet flap wings of arbitrary geometry.

Paper presents a design technique for rapidly computing lift, induced drag, and spanwise loading of unswept jet flap wings of arbitrary thickness, chord, twist, blowing, and jet angle, including discontinuities. Linear theory is used, extending Spence's method for elliptically loaded jet flap wings. Curves for uniformly blown rectangular wings are presented for direct performance estimation. Arbitrary planforms require a simple computer program. Method of reducing wing to equivalent stretched, twisted, unblown planform for hand calculation is also given. Results correlate with limited existing data, and show lifting line theory is reasonable down to aspect ratios of 5.

Lissaman, P. B. S.↗
NASA NTRS1974

Reversed cowl-flap thrust augmentor

Inlet mouthpiece with variable geometry improves low-speed performance of inlet (or ejector) of jet engines by use of reversed cowl-flap mechanism. Flaps can be adjusted mechanically or system can be operated with pressure taps set so pressure on inlet face is always smaller than pressure on back of inlet.

Cheng, D. Y.↗
NASA NTRS1973

March 1971 wind tunnel tests of the Dorand DH 2011 jet flap motor, volume 2

Wind tunnel tests were conducted of the Dorand DH 2011D jet flap rotor. The data recorded during the tests consist of: (1) multicyclic cam coefficients, (2) stress analysis, (3) vibratory loads, (4) Fourier analysis of flap deflection, and (5) blade bending stress. Data are presented in the form of tables and graphs.

Kretz, M.↗
NASA NTRS1974

Rational function representation of flap noise spectra including correction for reflection effects

A rational function is presented for the acoustic spectra generated by deflection of engine exhaust jets for under-the-wing and over-the-wing versions of externally blown flaps. The functional representation is intended to provide a means for compact storage of data and for data analysis. The expressions are based on Fourier transform functions for the Strouhal normalized pressure spectral density, and on a correction for reflection effects based on the N-independent-source model of P. Thomas extended by use of a reflected ray transfer function. Curve fit comparisons are presented for blown flap data taken from turbofan engine tests and from large scale cold-flow model tests. Application of the rational function to scrubbing noise theory is also indicated.

Miles, J. H.↗
NASA NTRS1974

Low speed aerodynamic characteristics of NACA 6716 and NACA 4416 airfoils with 35 percent-chord single-slotted flaps

An investigation was conducted in a low-turbulence pressure tunnel to determine the two-dimensional lift and pitching-moment characteristics of an NACA 6716 and an NACA 4416 airfoil with 35-percent-chord single-slotted flaps. Both models were tested with flaps deflected from 0 deg to 45 deg, at angles of attack from minus 6 deg to several degrees past stall, at Reynolds numbers from 3.0 million to 13.8 million, and primarily at a Mach number of 0.23. Tests were also made to determine the effect of several slot entry shapes on performance.

Bingham, G. J.↗
NASA NTRS1972

A Structural Design for an Externally Blown Flap (EBF) Medium STOL Research Aircraft

A computer program to predict, by reference to structural drawings, the dynamic response of a high lift STOL wing with externally blown flaps was developed. Structural data for the computer program are presented in the form of sketches, weight and dynamic loads information graphs, and tables for an external blown, triple-slotted flap, high lift STOL transport wing. Weight, mass distribution, and moment of inertia data are summarized in table form and presented pictorially by drawing layout. The methods used for obtaining weight data were: (1) actual know, weight of components, (2) preliminary stress sizing, and (3) statistical weight estimating methods.

Source record↗
NASA NTRS1974

A theoretical study of the application of jet flap circulation control for reduction of rotor vibratory forces

The results of a study to investigate the theoretical potential of a jet-flap control system for reducing the vertical and horizontal non-cancelling helicopter rotor blade root shears are presented. A computer simulation describing the jet-flap control rotor system was developed to examine the reduction of each harmonic of the transmitted shears as a function of various rotor and jet parameters, rotor operating conditions and rotor configurations. The computer simulation of the air-loads included the influences of nonuniform inflow and blade elastic motions. (no hub motions were allowed.) The rotor trim and total rotor power (including jet compressor power) were also determined. It was found that all harmonics of the transmitted horizontal and vertical shears could be suppressed simultaneously using a single jet control.

Piziali, R. A.↗
NASA NTRS1974

Wind-tunnel investigation of an externally blown flap STOL transport model including and investigation of wall effects

A wind-tunnel investigation was conducted in the Langley V/STOL tunnel and in a scaled version of the Ames 40- by 80-foot tunnel test section installed as a liner in the Langley V/STOL tunnel to determine the effect of test-section size on aerodynamic characteristics of the model. The model investigated was a swept-wing, jet-powered, externally blown flap (EBF) STOL transport configuration with a leading-edge slat and triple-slotted flaps. The model was an 0.1645-scale model of a 11.58-meter (38.0-ft) span model designed for tests in a 40- by 80-foot tunnel. The data compare the aerodynamic characteristics of the model with and without the tunnel liner installed. Data are presented as a function of thrust coefficient over an angle-of-attack range of 0 deg to 25 deg. A thrust-coefficient range up to approximately 4.0 was simulated, most ot the tests being conducted at a free-stream dynamic pressure of 814 Newtons/sq m (17 lb sq ft). The data are presented with a minimum of analysis.

Gentry, G. L., Jr.↗