Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “experimental data error”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

Fault-tolerant clock synchronization validation methodology

A validation method for the synchronization subsystem of a fault-tolerant computer system is presented. The high reliability requirement of flight-crucial systems precludes the use of most traditional validation methods. The method presented utilizes formal design proof to uncover design and coding errors and experimentation to validate the assumptions of the design proof. The experimental method is described and illustrated by validating the clock synchronization system of the Software Implemented Fault Tolerance computer. The design proof of the algorithm includes a theorem that defines the maximum skew between any two nonfaulty clocks in the system in terms of specific system parameters. Most of these parameters are deterministic. One crucial parameter is the upper bound on the clock read error, which is stochastic. The probability that this upper bound is exceeded is calculated from data obtained by the measurement of system parameters. This probability is then included in a detailed reliability analysis of the system.

Computer systems↗

Flight demonstrations of curved, descending approaches and automatic landings using time referenced scanning beam guidance

The Terminal Configured Vehicle (TCV) program operates a Boeing 737 modified to include a second cockpit and a large amount of experimental navigation, guidance and control equipment for research on advanced avionics systems. Demonstration flights to include curved approaches and automatic landings were tracked by a phototheodolite system. For 50 approaches during the demonstration flights, the following results were obtained: the navigation system, using TRSB guidance, delivered the aircraft onto the 3 nautical mile final approach leg with an average overshoot of 25 feet past centerline, subjet to a 2-sigma dispersion of 90 feet. Lateral tracking data showed a mean error of 4.6 feet left of centerline at the category 1 decision height (200 feet) and 2.7 feet left of centerline at the category 2 decision height (100 feet). These values were subject to a sigma dispersion of about 10 feet. Finally, the glidepath tracking errors were 2.5 feet and 3.0 feet high at the category 1 and 2 decision heights, respectively, with a 2 sigma value of 6 feet.

White, W. F.↗

Word timing recovery in direct detection optical PPM communication systems with avalanche photodiodes using a phase lock loop

A technique for word timing recovery in a direct-detection optical PPM communication system is described. It tracks on back-to-back pulse pairs in the received random PPM data sequences with the use of a phase locked loop. The experimental system consisted of an 833-nm AlGaAs laser diode transmitter and a silicon avalanche photodiode photodetector, and it used Q = 4 PPM signaling at source data rate 25 Mb/s. The mathematical model developed to describe system performance is shown to be in good agreement with the experimental measurements. Use of this recovered PPM word clock with a slot clock recovery system caused no measurable penalty in receiver sensitivity. The completely self-synchronized receiver was capable of acquiring and maintaining both slot and word synchronizations for input optical signal levels as low as 20 average detected photons per information bit. The receiver achieved a bit error probability of 10 to the -6th at less than 60 average detected photons per information bit.

Sun, Xiaoli↗

A single-axis testbed for slewing control experiments

A simple single-axis testbed is described, and initial experimental results are presented to illustrate collocated and noncollocated control for this structure. The testbed is made up of a pair of single-axis flexible beams attached to a DC servo motor. An optical encoder and strain gauges provide hub and beam position information, respectively. The system is driven by an IBM PC system; with a motor controller, a programmable digital filter processes position error information through user-selected gains and pole-zero configurations. A 25-kHz data acquisition system provides the necessary interface between processor and motor. The control approaches currently being investigated include collocated PD control and noncollocated phase compensation.

Hamilton, Jonathan↗

Deployable reflector antenna performance optimization using automated surface correction and array-feed compensation

Methods for increasing the electromagnetic (EM) performance of reflectors with rough surfaces were tested and evaluated. First, one quadrant of the 15-meter hoop-column antenna was retrofitted with computer-driven and controlled motors to allow automated adjustment of the reflector surface. The surface errors, measured with metric photogrammetry, were used in a previously verified computer code to calculate control motor adjustments. With this system, a rough antenna surface (rms of approximately 0.180 inch) was corrected in two iterations to approximately the structural surface smoothness limit of 0.060 inch rms. The antenna pattern and gain improved significantly as a result of these surface adjustments. The EM performance was evaluated with a computer program for distorted reflector antennas which had been previously verified with experimental data. Next, the effects of the surface distortions were compensated for in computer simulations by superimposing excitation from an array feed to maximize antenna performance relative to an undistorted reflector. Results showed that a 61-element array could produce EM performance improvements equal to surface adjustments. When both mechanical surface adjustment and feed compensation techniques were applied, the equivalent operating frequency increased from approximately 6 to 18 GHz.

Schroeder, Lyle C.↗

Comanche Helmet-Mounted Display Symbology Simulation

The Aeroflightdynamics Directorate (AMRDEC) conducted a simulation to examine the performance of the Comanche Contact Analog world-referenced symbology displayed on the Comanche HIDSS when compared with a compressed symbology design similar to that specified by the former MIL-STD 1295. Six experimental test pilots flew one modified ADS-33 maneuver (hover turn, bob-up), an unusual attitude recovery, and two terrain flight tactical tasks in the NASA Vertical Motion Simulator (VMS). Analysis of the pilot objective performance data and subjective data showed the following results. Objective test results showed that 1295 symbology yielded more rapid maneuvering in the hover turn bob-up than Contact Analog symbology. The average margin of difference in the time to complete the maneuver was approximately two seconds, which was statistically significant. There were no significant differences measured between symbology sets with respect to altitude or position performance measures for all other maneuvers. The NOE target ID task data showed improved accuracy in determining heading to target when using Contact Analog over MIL-STD-1295. Subjective test results, including handling qualities ratings (HQRs) and NASA-TLX workload ratings, showed small but consistent advantages of 1295 symbology over Contact Analog for most parameters. For the bob-up maneuver, 1295 symbology handling qualities were rated Desired for lateral position error and time to complete whereas Contact Analog was rated adequate. The average HQRs for all other maneuvers were rated the same for both symbology sets. Pilot comments and the results of an online questionnaire more strongly favored 1295 over Contact Analog. Repeated comments from all six pilots led to a focus on design issues with six Contact Analog symbols. Those symbols were the heading tape, horizon line, radar altitude six-second predictor, the position of the torque symbol, the absence of a hover position cue, and the widespread positioning of the symbology to the outer edges of the display field-of-view. Pilots rated the present design of three of the six symbols as having safety-of-flight implications. Those symbols were the heading tape, horizon line, and six-second predictor. To summarize, test results showed no objective data that would warrant restricting experimental test pilots from flying constrained tasks. Small but consistent advantages were recorded for the MILSTD-1295 symbology design when executing ADS-33 constrained tasks. No general performance differences were recorded for the operational maneuvers (NOE, contour flight modes) except for the azimuth-to-target task, which favored the Contact Analog heading tape design. There were consistent and strong pilot comments supporting the MIL-STD-1295 design over Contact Analog in both this current simulation and in Comanche Sim I. Three Contact Analog symbols warrant modification and further evaluation to mitigate safety-of-flight implications noted by participating test pilots. A plan for symbology redesign and testing was developed. However, the Comanche program was cancelled by Department of Army in February 2004.

Turpin, Terry S.↗

Calculations of H2O microwave line broadening in collisions with He atoms - Sensitivity to potential energy surfaces

Theoretical computations of broadening parameters are reported for three microwave lines of H2O in a bath of He atoms. The potential-energy surfaces employed are corrected for basis-set superposition error, and their reliability is checked by repeating the calculations with a different basis set for orbital expansion. The results are presented in extensive tables and discussed in detail. The corrections applied are shown to have a significant impact on the accuracy of the room-temperature broadenings determined: 8.9 sq A for the 22.2-GHz line, 11.8 sq A for the 183,3-GHz line, and 10.0 sq A for the 380.2-GHz line, in good agreement with published experimental data. The importance of collisional broadening for the atmospheric transmission of radiation and for remote-sensing applications is indicated.

Green, Sheldon↗

Evaluation of the solar disk sextant concept

In this paper the viability of the solar disk sextant concept is evaluated, the optimum parameters required to carry out solar variability studies, which are the mission objectives, are derived. The experimental environment is first discussed, followed by the application of the finite Fourier transform definition (FFTD) to the detector array data. The requirements on the optical system are studied next. A computer program was carried out simulating solar edge data and FFTD. From this study, it is concluded that the required accuracy of measurement may be reached using currently available detector array technology, a focal ratio of the optical system in excess of 90, and an entrance aperture of 22 cm. The guidance error must be small enough to require no more than a correction rate of 0.1 arcsec/sec. All these conditions are well within current technology.

Chiu, H.-Y.↗

ICP Reactor Modeling: CF4 Discharge

Inductively coupled plasma (ICP) reactors are widely used now for etching and deposition applications due to their simpler design compared to other high density sources. Plasma reactor modeling has been playing an important role since it can, in principle, reduce the number of trial and error iterations in the design process and provide valuable understanding of mechanisms. Fluorocarbon precursors have been the choice for oxide etching. We have data available on CF4 from our laboratory. These are current voltage characteristics, La.ngmuir probe data, UV-absorption, and mass spectrometry measurements in a GEC-ICP reactor. We have developed a comprehensive model for ICP reactors which couples plasma generation and transport and neutral species dynamics with the gas flow equations. The model has been verified by comparison with experimental results for a nitrogen discharge in an ICP reactor. In the present work, the model has been applied to CF4 discharge and compared to available experimental data.

Bose, Deepak↗

Fundamental Mistuning Model for Probabilistic Analysis Studied Experimentally

The Fundamental Mistuning Model (FMM) is a reduced-order model for efficiently calculating the forced response of a mistuned bladed disk. FMM ID is a companion program that determines the mistuning in a particular rotor. Together, these methods provide a way to acquire mistuning data in a population of bladed disks and then simulate the forced response of the fleet. This process was tested experimentally at the NASA Glenn Research Center, and the simulated results were compared with laboratory measurements of a "fleet" of test rotors. The method was shown to work quite well. It was found that the accuracy of the results depends on two factors: (1) the quality of the statistical model used to characterize mistuning and (2) how sensitive the system is to errors in the statistical modeling.

Griffin, Jerry H.↗

Flight Technical Error Analysis of the SATS Higher Volume Operations Simulation and Flight Experiments

This paper provides an analysis of Flight Technical Error (FTE) from recent SATS experiments, called the Higher Volume Operations (HVO) Simulation and Flight experiments, which NASA conducted to determine pilot acceptability of the HVO concept for normal operating conditions. Reported are FTE results from simulation and flight experiment data indicating the SATS HVO concept is viable and acceptable to low-time instrument rated pilots when compared with today s system (baseline). Described is the comparative FTE analysis of lateral, vertical, and airspeed deviations from the baseline and SATS HVO experimental flight procedures. Based on FTE analysis, all evaluation subjects, low-time instrument-rated pilots, flew the HVO procedures safely and proficiently in comparison to today s system. In all cases, the results of the flight experiment validated the results of the simulation experiment and confirm the utility of the simulation platform for comparative Human in the Loop (HITL) studies of SATS HVO and Baseline operations.

Williams, Daniel M.↗

Establishing Best Practices for X-57 Maxwell CFD Database Generation

The X-57 Maxwell is NASA’s latest electric airplane concept that has been simulated for aerodynamic performance using the structured overset and unstructured grid solvers within the Launch Ascent and Vehicle Aerodynamics (LAVA) solver framework as well as the unstructured polyhedral grid solver in Star-CCM+ for code-to-code comparison. In order to validate the predictions, comparisons were made between the CFD solutions and experimental data collected in the 12-foot Low-Speed Wind Tunnel at NASA Langley Research Center. The simulations are in preparation for the development of a comprehensive aerodynamic database which will assess aircraft performance at a variety of conditions. The findings from these simulations will establish the best practices for mesh resolution, numerical discretization, and turbulence modeling to be used for this database. Preliminary database results have shown that best-practices learned from the initial validation simulations will potentially reduce error in X-57 aerodynamic loads and moments relative to experiment by up to 14%.

Duensing, Jared C.↗

Evaluating Differences Among Crop Models in Simulating Soybean in-Season Growth

Crop models are useful tools for simulating agricultural systems that require continued model development and testing to increase their robustness and improve how they describe our current understanding of processes. Coordinated and “blind” evaluation of multiple models using same protocols and experimental datasets provides unique opportunities to further improve models and enhance their reliability. For soybean [Glycine max (L.) Merr.], there has been limited coordinated multi-model evaluations for the simulation of in-season plant growth dynamics. We evaluated ten dynamic soybean crop models for their simulation of in-season plant growth using data from five experiments conducted in Argentina, Brazil, France, and USA. We evaluated models after a Blind (using only phenology data) and a Full calibration (with in-season and end-of-season variables). Calibration reduced model uncertainty by reducing standard bias for the simulation of in-season variables (biomass, leaf, pod, and stem weights, and leaf area index, LAI). However, we found that most models had difficulty in reproducing leaf growth dynamics, with normalized root mean squared error (nRMSE) of 56% for leaf weight and 43% for LAI (across locations and models after Full calibration). Models with different levels of complexity and experience were capable of simulating final seed yield at maturity with reasonable accuracy (nRMSE of 8–31% after Full calibration). However, the nRMSE for pod weight (of 17–64% after Full calibration) was two-fold larger than that of seed yield. Moreover, the models differed in how they simulated timing from sowing to beginning seed growth (47–93 days) and effective seed filling period (18–54 days), owing to model structural differences in defining the reproductive developmental stages. Overall, we identified the following processes that can benefit from further model improvement: leaf expansion and senescence, reproductive phenology, and partitioning to reproductive growth. Simulation of pod wall tissue and individual seed cohorts is another aspect that many models currently lack. Model improvement can benefit from high-temporal resolution experimental datasets that concurrently account for phenology, plant growth, and partitioning. Further, we recommend collecting reproductive phenology in the field consistent with actual dry matter allocation to organs in the models and collecting multiple observations of seed and pod weight to aid model improvement for simulation of seed growth and yield formation.

Agricultural Model Intercomparison and Improvement↗

Soft X Ray Telescope (SXT) focus error analysis

The analysis performed on the soft x-ray telescope (SXT) to determine the correct thickness of the spacer to position the CCD camera at the best focus of the telescope and to determine the maximum uncertainty in this focus position due to a number of metrology and experimental errors, and thermal, and humidity effects is presented. This type of analysis has been performed by the SXT prime contractor, Lockheed Palo Alto Research Lab (LPARL). The SXT project office at MSFC formed an independent team of experts to review the LPARL work, and verify the analysis performed by them. Based on the recommendation of this team, the project office will make a decision if an end to end focus test is required for the SXT prior to launch. The metrology and experimental data, and the spreadsheets provided by LPARL are used at the basis of the analysis presented. The data entries in these spreadsheets have been verified as far as feasible, and the format of the spreadsheets has been improved to make these easier to understand. The results obtained from this analysis are very close to the results obtained by LPARL. However, due to the lack of organized documentation the analysis uncovered a few areas of possibly erroneous metrology data, which may affect the results obtained by this analytical approach.

Ahmad, Anees↗

Estimation of Unsteady Aerodynamic Models from Dynamic Wind Tunnel Data

Demanding aerodynamic modelling requirements for military and civilian aircraft have motivated researchers to improve computational and experimental techniques and to pursue closer collaboration in these areas. Model identification and validation techniques are key components for this research. This paper presents mathematical model structures and identification techniques that have been used successfully to model more general aerodynamic behaviours in single-degree-of-freedom dynamic testing. Model parameters, characterizing aerodynamic properties, are estimated using linear and nonlinear regression methods in both time and frequency domains. Steps in identification including model structure determination, parameter estimation, and model validation, are addressed in this paper with examples using data from one-degree-of-freedom dynamic wind tunnel and water tunnel experiments. These techniques offer a methodology for expanding the utility of computational methods in application to flight dynamics, stability, and control problems. Since flight test is not always an option for early model validation, time history comparisons are commonly made between computational and experimental results and model adequacy is inferred by corroborating results. An extension is offered to this conventional approach where more general model parameter estimates and their standard errors are compared.

Murphy, Patrick↗

Structural Model Tuning Tool: User's Reference Manual

This report presents an efficient approach for tuning finite element models to match the measured ground vibration test and static test data. Frequencies, mode shapes, total weight, location of the center of gravity, and static deformation computed from the finite element model are matched to the measured data. The model tuning procedure used in this work is based on solving an optimization problem in which the errors for the considered metrics, between the finite element prediction and the measured data, are minimized. Analytical sensitivity values of performance indices are computed using the NASTRAN-generated sensitivity values together with the in-house computer codes, which allow for faster computational time and the use of gradient-based optimizers. The method is applied to the Aerostructures Test Wing IV model. The study shows that the military standard and the National Aeronautics and Space Administration standard for comparing analytical and experimental modal data are all satisfied. The final finite element model correlates well with the test data. The flutter speed decreases by 8.91 percent after model tuning compared with the original Aerostructures Test Wing IV design.

Chan-gi Pak↗

Turbulence Studies of a Rectangular Slotted Noise-Suppressor Nozzle

The problem of noise suppression of turbojet engines has shown a need for turbulence data within the flow field of various types of nozzles used in ad hoc investigations of the sound power. The result of turbulence studies in a nozzle configuration of four parallel rectangular slots is presented in this report with special attention to the effect of the spacing of the nozzles on the intensity of turbulence, scale of turbulence, spectrum of turbulence, and the mean stream velocity. Taylor's hypothesis, which describes the convection of the turbulence eddies, was tested and found correct within experimental error and certain experimental and theoretical limitations. The convection of the pressure patterns was also investigated, and the value of the convection velocity was found to be about 0.43 times the central core velocity of the jets. The effect of the spacing-to-width ratio of the nozzles upon the turbulence intensity, the scale of turbulence, and the spectral distribution of the noise was found in general to produce a maximum change for spacing-to-width ratios of 1.5 to 2.0. These changes may be the cause of the reduction in sound power reported for similar full-scale nozzles and test conditions under actual (static) engine operation. A noise reduction parameter is defined from Lighthill's theory which gives qualitative agreement with experiments which show the noise reduction is greatest for spacing-to-width ratios of 1.5 to 2.0.

Laurence, James C.↗

Crop Model Improvement Reduces the Uncertainty of the Response to Temperature of Multi-Model Ensembles

To improve climate change impact estimates and to quantify their uncertainty, multi-model ensembles (MMEs) have been suggested. Model improvements can improve the accuracy of simulations and reduce the uncertainty of climate change impact assessments. Furthermore, they can reduce the number of models needed in a MME. Herein, 15 wheat growth models of a larger MME were improved through re-parameterization and/or incorporating or modifying heat stress effects on phenology, leaf growth and senescence, biomass growth, and grain number and size using detailed field experimental data from the USDA Hot Serial Cereal experiment (calibration data set). Simulation results from before and after model improvement were then evaluated with independent field experiments from a CIMMYT worldwide field trial network (evaluation data set). Model improvements decreased the variation (10th to 90th model ensemble percentile range) of grain yields simulated by the MME on average by 39% in the calibration data set and by 26% in the independent evaluation data set for crops grown in mean seasonal temperatures greater than 24 C. MME mean squared error in simulating grain yield decreased by 37%. A reduction in MME uncertainty range by 27% increased MME prediction skills by 47%. Results suggest that the mean level of variation observed in field experiments and used as a benchmark can be reached with half the number of models in the MME. Improving crop models is therefore important to increase the certainty of model-based impact assessments and allow more practical, i.e. smaller MMEs to be used effectively.

damage assessment↗