Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “drying”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Surface friction of rock in terrestrial and simulated lunar environments

The conventional probe-on-the rotating-disk concept was used to determine the surface friction in mineral probe/specimen interfaces. Nine rocks or minerals and two stainless steels were tested in both new (NT) and same track (ST) tests under three different pressure environments-atmospheric, UHV, and dry nitrogen. Each environment was further subdivided into two testing conditions, that is, ambient and elevated (135 C) temperatures. In NT tests, friction was the lowest in an atmospheric pressure condition for all rock types and increased to the largest in UHV ambient condition except for pyroxene and stainless steel. Friction values measured in dry nitrogen ambient condition lie between the two extremes. Heating tends to increase friction in atmospheric and dry nitrogen environment but decreases in UHV environment with the exception of stainless steel, basalt, and pyroxene. In ST tests, friction was the lowest in the first run and increased in subsequent runs except for stainless steel where the reverse was true. The increases leveled off after a few runs ranging from the second to the seventh depending on rock types.

Roepke, W. W.↗
NASA NTRS1977

Use of near infrared/red radiance ratios for estimating vegetation biomass and physiological status

The application of photographic infrared/red (ir/red) reflectance or radiance ratios for the estimation of vegetation biomass and physiological status were investigated by analyzing in situ spectral reflectance data from experimental grass plots. Canopy biological samples were taken for total wet biomass, total dry biomass, leaf water content, dry green biomass, dry brown biomass, and total chlorophyll content at each sampling date. Integrated red and photographic infrared radiances were regressed against the various canopy or plot variables to determine the relative significance between the red, photographic infrared, and the ir/red ratio and the canopy variables. The ir/red ratio is sensitive to the photosynthetically active or green biomass, the rate of primary production, and actually measures the interaction between the green biomass and the rate of primary production within a given species type. The ir/red ratio resulted in improved regression significance over the red or the ir/radiances taken separately. Only slight differences were found between ir/red ratio, the ir-red difference, the vegetation index, and the transformed vegetation index. The asymptotic spectral radiance properties of the ir, red, ir/red ratio, and the various transformations were evaluated.

Tucker, C. J.↗
NASA NTRS1977

Static performance of vectoring/reversing non-axisymmetric nozzles

An experimental program sponsored by the Air Force Flight Dynamics Laboratory is currently in progress to determine the internal and installed performance characteristics of five different thrust vectoring/reversing non-axisymmetric nozzle concepts for tactical fighter aircraft applications. Internal performance characteristics for the five non-axisymmetric nozzles and an advanced technology axisymmetric baseline nozzle were determined in static tests conducted in January 1977 at the NASA-Langley Research Center. The non-axisymmetric nozzle models were tested at thrust deflection angles of up to 30 degrees from horizontal at throat areas associated with both dry and afterburning power. In addition, dry power reverse thrust geometries were tested for three of the concepts. The best designs demonstrated internal performance levels essentially equivalent to the baseline axisymmetric nozzle at unvectored conditions. The best designs also gave minimum performance losses due to vectoring, and reverse thrust levels up to 50% of maximum dry power forward thrust. The installed performance characteristics will be established based on wind tunnel testing to be conducted at Arnold Engineering Development Center in the fall of 1977.

Willard, C. M.↗
NASA NTRS1977

Storage of solid propellants in space

A test program is described which determines the extent of physical property changes that result from extended space exposure. Primary emphasis was placed on determining the effects of space vacuum. Solid propellants were stored and their physical properties tested in a vacuum and in a dry environment. The storage caused significantly greater increases in the propellants' modulus and maximum tensile strength than occurred in parallel ambient stored samples. The data indicate that the loss of trace amounts of residual moisture from cured propellant is the apparent cause of the observed propellant property changes. Therefore, initial screening tests were carried out under dry storage conditions. Upon completion of the dry storage tests, appropriate propellant samples are exposed to an actual space environment using the Long Duration Exposure Facility (LDEF).

Udlock, D. E.↗
NASA NTRS1977

Variational analysis of temperature and moisture advection in a severe storm environment

Horizontal wind components, potential temperature, and mixing ratio fields associated with a severe storm environment in the south central United States were objectively analyzed from synoptic upper air observations with a nonhomogeneous anisotropic weighting function. The particular case study discussed here is the tornado producting squall line which moved through eastern Oklahoma 26 May 1973. The synoptic situation which preceded squall line development was cyclogenesis and frontogenesis in the lee-of-mountain trough, which produced a well-defined surface dry line (or dew point front) and a pronounced mid-level dry air intrusion. It is shown that the intrusion was also characterized by warm air, with a lapse rate approaching the dry adiabatic.

Mcfarland, M. J.↗
NASA NTRS1979

Automated Array Assembly Task In-depth Study of Silicon Wafer Surface Texturizing

A low cost wafer surface texturizing process was studied. An investigation of low cost cleaning operations to clean residual wax and organics from the surface of silicon wafers was made. The feasibility of replacing dry nitrogen with clean dry air for drying silicon wafers was examined. The two stage texturizing process was studied for the purpose of characterizing relevant parameters in large volume applications. The effect of gettering solar cells on photovoltaic energy conversion efficiency is described.

Jones, G. T.↗
NASA NTRS1979

Automated Array Assembly Task In-depth Study of Silicon Wafer Surface Texturizing

Several aspects of silicon wafer surface texturizing were studied. A low cost cleaning method that utilizes recycled Freon in an ultrasonic vapor degreaser to remove organic and inorganic contaminants from the surface of silicon wafers as received from silicon suppliers was investigated. The use of clean dry air and high throughout wafer batch drying techniques was shown to lower the cost of wafer drying. A two stage texturizing process was examined for suitability in large scale production. Also, an in-depth gettering study with the two stage texturizing process was performed for the enhancement of solar cell efficiency, minimization of current versus voltage curve dispersion, and improvement in process reproducibility. The 10% efficiency improvement goal was exceeded for the near term implementation of flat plate photovoltaic cost reduction.

Jones, G. T.↗
NASA NTRS1980

Effects of moisture, residual thermal curing stresses and mechanical load on the damage development in quasi-isotropic laminates

Classical laminate theory and a finite element model were used to predict stress states prior to the first formation of damage in laminates fabricated from T/300/5208. Crack patterns characteristic of the laminate in a wet or dry condition were also predicted using a shear lag model. Development of edge damage was recorded and observed during the test by transferring an image of the damage from the edge surface on to a thin acetate sheet such that the damage imprinted could be immediately viewed on a microfiche card reader. Moisture was shown to significantly alter the interior and edge dry stress states due to swelling and a reduction of elastic properties and to reduce the transverse strength in 90 deg plies. A model was developed in order to predict changes in first ply failure laminate loads due to differences in stacking sequence together with a wet or dry environmental condition.

Kriz, R. D.↗
NASA NTRS1979

Seismic Q and velocity at depth

Measurements of the p-wave and s-wave internal friction quality factors (Q) and velocities of samples of a moderately outgassed terrestrial analog of lunar basalt exposed simultaneously to temperatures and hydrostatic confining pressures in accordance with the best available estimates of the lunar selenotherm are presented. Q values and velocities are found to increase with simulated depth, and an extrapolation of the Q value to a thoroughly outgassed states provides a Q value in reasonable agreement with those derived from lunar seismic data, suggesting a very dry lunar crust. Results also imply that similar seismic determinations for Mars would be able to distinguish between a dry crust and a crust containing water trapped beneath a layer of ice. Results of thermal cracking tests which demonstrate that high degrees of cracking associated with thermal cycling, as during the lunar day, are not inconsistent with high Q in a dry environment are presented, and it is shown that volatiles with diple moments comparable to H2O can greatly affect Q. Possible attenuation mechanisms are then considered, and velocity measurements on a synthetic anorthosite are presented.

Tittmann, B. R.↗
NASA NTRS1980

Anti-reflection coatings on large area glass sheets

Antireflective coatings which may be suitable for use on the covers of photovoltaic solar modules can be easily produced by a dipping process. The coatings are applied to glass by drawing sheets of glass vertically out of dilute aqueous sodium silicate solutions at a constant speed, allowing the adherent liquid film to dry, then exposing the dried film to concentrated sulfuric acid, followed by a water rinse and dry. The process produces coatings of good optical performance (96.7 percent peak transmission at 0.540 mu M wavelength) combined with excellent stain and soil resistance, and good resistance to abrasion. The process is reproduceable and easily controlled.

Pastirik, E.↗
NASA NTRS1955

Investigation of Porous Gas-Heated Leading-Edge Section for Icing Protection of a Delta Wing

A tip section of a delta wing having an NACA 0004-65 airfoil section and a 600 leading-edge sweepback was equipped with a porous leading-edge section through which hot gas was 'bled for anti-icing. Heating rates for anti-icing were determined for a wide range of icing conditions. The effects of gas flow through the porous leading-edge section on airfoil pressure distribution and drag in dry air were investigated. The drag increase caused by an ice formation on the unheated airfoil was measured for several icing conditions. Experimental porous surface- to free-stream convective heat-transfer coefficients were obtained in dry air and compared with theory. Adequate icing protection was obtained at all icing conditions investigated. Savings in total gas-flow rate up to 42 percent may be obtained with no loss in anti-icing effectiveness by sealing half the upper-surface porous area. Gas flow through the leading-edge section had no appreciable effect on airfoil pressure distribution. The airfoil section drag increased slightly (5-percent average) with gas flow through the porous surface. A heavy glaze-ice formation produced after 10 minutes of icing caused an increase in section drag coefficient of 240 percent. Experimental convective heat-transfer coefficients obtained with hot-gas flow through the porous area in dry air and turbulent flow were 20 to 30 percent lower than the theoretical values for a solid surface under similar conditions. The transition region from laminar to turbulent flow moved forward as the ratio of gas velocity through the porous surface to air-stream velocity was increased.

Bowden, Dean T.↗
NASA NTRS1982

Characterization of advanced electric propulsion systems

Characteristics of several advanced electric propulsion systems are evaluated and compared. The propulsion systems studied are mass driver, rail gun, MPD thruster, hydrogen free radical thruster and mercury electron bombardment ion engine. These are characterized by specific impulse, overall efficiency, input power, average thrust, power to average thrust ratio and average thrust to dry weight ratio. Several important physical characteristics such as dry system mass, accelerator length, bore size and current pulse requirement are also evaluated in appropriate cases. Only the ion engine can operate at a specific impulse beyond 2000 sec. Rail gun, MPD thruster and free radical thruster are currently characterized by low efficiencies. Mass drivers have the best performance characteristics in terms of overall efficiency, power to average thrust ratio and average thrust to dry weight ratio. But, they can only operate at low specific impulses due to large power requirements and are extremely long due to limitations of driving current. Mercury ion engines have the next best performance characteristics while operating at higher specific impulses. It is concluded that, overall, ion engines have somewhat better characteristics as compared to the other electric propulsion systems.

Ray, P. K.↗
NASA NTRS1984

Crystal Microbalance Monitors Relative Humidity

Sensor monitors water evaporation in industrial drying processes. Measured adsorption isotherm for instrument essentially linear over entire range of relative humidity. Testing at each temperature setting less than half hour for full relative-humidity range, with estimated frequency response time less than 10 seconds. Used to measure relative humidity of ambient atmosphere near drying paper, food textile fabrics and pulp to optimize water-drying portion of processing cycle.

Yang, L. C.↗
NASA NTRS1982

Subsurface valleys and geoarcheology of the eastern Sahara revealed by Shuttle radar

Previously unknown buried valleys, geologic structures, and possible Stone Age occupation sites have been revealed through the Shuttle Imaging Radar (SIR-A) penetration of the extremely dry Selima Sand Sheet, dunes and drift sand of the eastern Sahara. Radar penetration of dry sand and soils varies with the wavelength of the incident signals, which is 24 cm for the SIR-A system, as well as incidence angle and electrical properties of the material which are largely determined by moisture content. The calculated depth of radar penetration of dry sand and granules has been established to be 5 m on the basis of laboratory measurements of Selima Sand Sheet sample electrical properties. September 1982 field studies in Egypt have verified SIR-A signal penetration depths of at least 1 m in the Selima Sand Sheet and drift sand, and 2 m or more in sand dunes.

Mccauley, J. F.↗
NASA NTRS1982

Effects of moisture, residual thermal curing stresses, and mechanical load on the damage development in quasi-isotropic laminates

This investigation demonstrates how moisture absorbed in (0/+ or - 45/90)s and (0/90/+ or - 45)s graphite epoxy laminates significantly alters the stress state and chronology of damage development along the laminate edge during static tension and tension-tension cyclic loading. Emphasis is placed on using reasonable approximations for wet and dry elastic properties, including out-of-plane properties (nu sub 23 and G sub 23), since these properties are required by finite element and shear lag models to predict the stress state at the laminate edge. Moisture was observed to alter the dry edge stress state in the 90-deg plies of the (0/+ or - 45/90)s laminate such that delaminations occurred at a lower load and transverse cracks occurred at a higher load. A model was developed which predicted the differences in loads required to initiate damage in the 90-deg plies of the two laminates in the wet and dry conditions. Although moisture can alter the chronology of damage development, the damage state in each laminate observed prior to fracture appeared to be independent of moisture content.

Kriz, R. D.↗
NASA NTRS1984

Chromium electrodes for REDOX cells

An improved electrode having a gold coating for use in the anode compartment of a REDOX cell is described. The anode fluid utilizes a chromic/chromous couple. A carbon felt is soaked in methanol, rinsed in water, dried and then heated in KOH after which it is again washed in deionized water and dried. The felt is then moistened with a methanol water solution containing chloroauric acid and is stored in a dark place while still in contact with the gold-containing solution. After all the gold-containing solution is absorbed in the felt, the latter is dried by heat and then heat treated at a substantially greater temperature. The felt is then suitable for use as an electrode and is wetted with water or up to two molar HCl prior to installation in a REDOX cell. The novelty of the invention lies in the use of KOH for cleaning the felt and the use of alcohol as a carrier for the gold together with the heat treating procedure.

Jalan, V.↗
NASA NTRS1982

High density circuit technology, part 3

Dry processing - both etching and deposition - and present/future trends in semiconductor technology are discussed. In addition to a description of the basic apparatus, terminology, advantages, glow discharge phenomena, gas-surface chemistries, and key operational parameters for both dry etching and plasma deposition processes, a comprehensive survey of dry processing equipment (via vendor listing) is also included. The following topics are also discussed: fine-line photolithography, low-temperature processing, packaging for dense VLSI die, the role of integrated optics, and VLSI and technology innovations.

Wade, T. E.↗
NASA NTRS1984

Algal culture studies related to a closed ecological life support system

Studies on the steady-state long-term (4 month) culture of Scenedesmus obliquus algae, maintained in an annular air-lift column operated as a turbidostat, were carried out to evaluate the life-supporting possibilities of this system. Chlorophyll production and cell number as functions of the dry weight were linear at constant illumination. Productivity (measured as the product of dry weight, mg/ml, and the growth rate, ml/hr) vs. dry weight rose linearly until the cell density reached a level at which light became limiting (89 percent absorption of the photosynthetically active radiation). In the initial, linear portion of the curve, the productivity was limited by cell growth at the given light intensity. The maximum dilution rate of the system corresponded to the doubling time of 13.4 hr, about half the maximum rate, with a productivity of 80 percent of the maximum theoretical productivity. The high light utilization efficiencies were contributed by the low (10 percent of full sunlight) incident intensities.

Radmer, R.↗