Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “capacity change”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Physical Properties of Hilti HIT-RE 500 V3 After Irradiation: Slant Shear, Tensile, Flexural, and Compressive

There are various applications in which epoxy adhesives may be used within hot-cell environments. These epoxies currently see limited use within hot cells since it is known that organics see degradation after small doses even as low as 50 kilogray (kGy). These losses in physical property strengths limit the use of these epoxies to non-structural applications. In modern construction, however, the use of epoxies to bond structural components such as rebar or threaded anchors is becoming increasingly prevalent. To employ these types of materials the Idaho National Laboratory (INL) has begun investigating the specific degradation properties of epoxies for use in structural applications in environments where radiation is present. Hilti HIT-RE 500 V3 is used extensively in new construction and renovation projects across the world. The INL has conducted various tests on this epoxy for low dose environments. These tests include tensile, flexural, compression, and slant shear tests following the American Society for Testing Material International (ASTM) standards D638, D790, D695, and C882/882M respectively. Two sample sets for each test were created where the baseline specimens were not irradiated, and another set was irradiated to an accumulated dose of approximately 50-60 kGy. All the samples were destructively tested and analyzed focusing on the change in physical properties, examples of these tests are shown in Figures 1-4. Tensile testing results indicate a 0.9% loss in maximum load capacity, a 0.5% loss in tensile stress at maximum load, a 1.4% loss in tensile strain at break, and a 15% decrease in modulus of elasticity. Flexural testing results display an increase in all the following: 12% in strain at maximum load, 10% in maximum load capacity, 5% in stress at maximum load, and 3% in young’s modulus. The compressive physical properties after irradiation display a 1% increase in maximum load, a 3% decrease in stress at yield, and a 5% decrease in modulus of elasticity. The maximum compressive stress saw no measurable change after irradiation. The slant shear specimens after irradiation displayed a 2% increase in maximum load capacity and maximum compressive stress. Though a structural analysis would have to be completed as is normal for building design the increases and decreases in the measured physical properties indicate that this material may be used for structural applications in low dose hot-cell environments without adhesive failure.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Nanocomposite battery electrode particles with changing properties

Battery electrode compositions and methods of fabrication are provided that utilize composite particles. Each of the composite particles may comprise, for example, a high-capacity active material and a porous, electrically-conductive scaffolding matrix material. The active material may store and release ions during battery operation, and may exhibit (i) a specific capacity of at least 220 mAh/g as a cathode active material or (ii) a specific capacity of at least 400 mAh/g as an anode active material. The active material may be disposed in the pores of the scaffolding matrix material. According to various designs, each composite particle may exhibit at least one material property that changes from the center to the perimeter of the scaffolding matrix material.

Yushin, Gleb↗
DOE OSTI2023

Nanocomposite battery electrode particles with changing properties

Battery electrode compositions and methods of fabrication are provided that utilize composite particles. Each of the composite particles may comprise, for example, a high-capacity active material and a porous, electrically-conductive scaffolding matrix material. The active material may store and release ions during battery operation, and may exhibit (i) a specific capacity of at least 220 mAh/g as a cathode active material or (ii) a specific capacity of at least 400 mAh/g as an anode active material. The active material may be disposed in the pores of the scaffolding matrix material. According to various designs, each composite particle may exhibit at least one material property that changes from the center to the perimeter of the scaffolding matrix material.

Yushin, Gleb↗
DOE OSTI2022

Constructing O2/O3 homogeneous hybrid stabilizes Li-rich layered cathodes

With the advantages of high energy density and low manufacture cost, lithium-rich layered oxides (LLOs), typically with a layered O3-type structure, are regarded as promising cathodes for lithium-ion batteries (LIBs), but their broad usages are hindered by severe voltage decay over cycling. Although recent progress in O2-type LLOs has aroused interest for their less voltage decay, the critical barrier of unsatisfactory capacity retention has not been overcome yet. In this work, to tackle these handicaps, we design a new type of LLO (O2/O3-type LLO) with a homogeneous hybrid structure, where the O2 and O3 lattice stacking sequences are arranged alternatively. Benefitting from this novel O2/O3 hybrid structure, the designed material shows greatly improved voltage and capacity stability than that of pure O2- and O3-type LLOs. Revealed by in-situ synchrotron X-ray diffraction and operando differential electrochemical mass spectra, the O2/O3-hybrid LLO cathode shows a more reversible structural evolution, smaller volume change and suppressed oxygen loss during the electrochemical processes. Our approach has initiated a new way to reduce the capacity and voltage decay of LLOs, which endows great promise to the development of high-energy-density LIBs.

25 ENERGY STORAGE↗
DOE OSTI2025

Dual‐Gradient Construction on Li‐Rich Cathodes for High Stability Lithium Battery

Abstract The practical applications of high‐energy Li‐rich layered oxides (LLOs) have been hindered by the severe performance degradation including voltage decay and capacity fading. The gradient construction toward high‐activity interior and high‐stability exterior, typically realized by gradually changed transition metal (TM) gradient in LLOs, can alleviate the performance degradation to certain degrees. In this study, a gradient design of Al/Mg dopants is demonstrated for the TM‐gradient LLOs to further harmonize the high‐activity interior and high‐stability exterior, thereby forming the dual (TM and doping) gradient. As a result, superior capacity retention of 86% and a minor voltage decay of 0.54 mV cycle −1 are achieved at 1 C after 300 cycles. The improved electrochemical stability of the dual‐gradient LLO is attributed to the enhanced surface stability and suppressed bulk structure degeneration of LLOs upon electrochemical cycling. The dual‐gradient design serves as an important approach to fabricate high‐performance bulk LLOs toward applications.

Wu, Tianhao↗
NASA NTRSDate not supplied

Temporal Changes in Astronauts’ Muscle and Cardiorespiratory Physiology Before, During, and After Spaceflight

Background: NASA’s planned space exploration missions will require astronauts to safely perform extravehicular activity (EVA) and to safely egress vehicles in a variety of landing scenarios. Prolonged exposure to spaceflight can diminish tolerance for physical activity, decrease cardiovascular and sensorimotor function, cause loss of bone mineral density, as well as reduced muscle mass and strength. Although exercise can mitigate these spaceflight-induced physiological decrements, little is known regarding the time-course of changes in muscle and aerobic performance during spaceflight. Furthermore, these exercise countermeasures are not fully protective. For example, maximal aerobic capacity (VO2pk), lower body muscle cross-sectional area, and strength decrease by about 10% to 15% after short- (≈14 days) and long-duration (≈6 months) missions on the International Space Station (ISS). Future space missions longer in duration and further from Earth will employ exploration vehicles that will have exercise hardware with less robust and more constrained exercise capabilities than of those available on the ISS. Thus, countermeasures will need to be optimized to protect crew health and performance on exploration-class missions lasting up to 3 years. This requires a more detailed understanding of the dynamic effects of spaceflight on human health and performance, the ability of exercise to protect against this deconditioning, and the interaction of exercise with interrelated factors like nutrition, sleep, and environmental conditions. Methods: We will use standardized research and medical testing protocols previously validated in 1g and microgravity to quantify the time course and the inter-individual variability of changes in physical performance, including cardiorespiratory fitness and muscle strength and endurance, before, during, and after spaceflight missions lasting 2 months, 6 months, and 1 year. Additionally, we will use an extrapolation model to predict changes associated with multi-year exploration missions. Additionally, we will monitor in-flight exercise, nutrition, and sleep using in-flight assessment tools. Significance: Our testing protocols will provide valuable information for determining time course of change and the interindividual variability of spaceflight-induced deconditioning of aerobic capacity and muscle strength and endurance over the course of spaceflight missions up to and beyond 1 year. This information will be vital to assess whether humans can be physically ready for deep space exploration, such as on a mission to Mars, using current technology, or if additional mitigation strategies are necessary.

N Strock↗
NASA NTRS1983

Thermal-protection requirements for near-earth aero-assisted orbital-transfer vehicle missions

The thermal protection required for decelerating and maneuvering spacecraft by aerodynamic forces is determined for return missions from geosynchronous to low-earth orbits. The effect of vehicle configuration on surface heating rates and selection of heat-shield materials is analyzed. Effects of the current widespread estimates in the structure of atmospheric density are also evaluated. It is shown that nonequilibrium radiation can be a major source of surface heating during atmospheric entry and a significant factor to heat-shielding requirements. It is also demonstrated that drag-brake concepts have application to a broad range of orbital-transfer missions, because of the favorable trade-offs with aeromaneuvering vehicles in volumetric efficiency, retrothrust plane-change capability, and heat-protection requirements. In addition, the results of this study indicate that the aero-assist technique produces small penalties in vehicle payload capacity for drag-brake concepts, because of the system's heat protection requirements, and is highly attractive relative to all-propulsive orbital-change maneuvers.

Menees, G. P.↗
DOE OSTI2022

Carboxylic Group Rotation and Lattice Expansion in a Co 2 (Pyrazine-2,3-Dicarboxylate) 2 (4,4'-Bipyridine) Porous Coordination Polymer Induced by CO 2 Adsorption at Ambient Temperature

Here, a Co 2 (pzdc) 2 (bpy)(H 2 O) m (pzdc: pyrazine-2,3dicarboxylate; bpy: 4,4'-bipyridine) porous coordination polymer (PCP) was studied for CO 2 uptake and concomitant structural changes at ambient temperature. Extended structural characterization included evaluation of lattice parameter changes upon CO 2 adsorption and in situ synchrotron X-ray powder diffraction data. The PCP effective pore size increased by ~2% with gas uptake over the pressure range of 1-50 atm, allowing the adsorption capacity to double. Furthermore, the hysteretic behaviors seen during CO 2 adsorption at moderate pressures are commensurate with the structural changes from synchrotron data. The adsorption and hysteresis occur with rotation of the linking carboxylate groups, and yet only minor changes in unit cell volume (ΔV ≈ 6 Å 3 ) are observed. This contrasts the findings for [Cu 2 (pzdc) 2 (bpy)] n , where a combination of pillar bpy rotations and significant lattice expansion (ΔV ≈ 68 Å(3)) takes place upon hysteretic adsorption of CO 2 . In situ high-temperature X-ray diffraction revealed that the Co(II)-based material has good thermal stability up to ca. 200° C. Finally, the CO 2 uptake also appears to be at a physisorption level, with adsorbent-adsorbate interactions that are ca. 30% stronger than what has been reported for CO 2 adsorption onto [Cu 2 (pzdc) 2 (bpy)] n .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Linking Pressure to Electrochemical Evolution in Solid-State Conversion Cathode Composites

Conversion-type cathodes, such as sulfur, FeS 2 , and FeF 3 , offer high theoretical capacities in solid-state lithium batteries but are hindered by substantial volume changes during cycling, leading to interfacial contact loss, crack formation, and microstructural degradation. Here, we investigate the relationships between electrochemical, mechanical, and structural evolution in solid-state electrode composites with these three active materials. Using real-time stack-pressure monitoring, synchrotron X-ray absorption spectroscopy, and electrokinetic modeling, we elucidate how stress evolution is linked to reversible and irreversible redox reactions. Nonlinear stack pressure evolution in cells with sulfur, FeS 2 , and FeF 3 electrode composites is found to arise from material-specific volume changes, the balance of volume change between the working and counter electrode, and the formation of distinct reaction intermediates. The three materials exhibit distinct stack pressure evolution, which is closely related to the different reaction processes in the materials, as demonstrated with X-ray absorption spectroscopy measurements. Through mesoscale modeling, we relate the experimental measurements to species evolution at the particle scale and track the dynamic coexistence of intermediate phases. Our findings highlight the importance of designing for volume changes of a given active material in solid-state battery systems.

batteries↗
DOE OSTI2023

Topology-enhanced mechanical stability of swelling nanoporous electrodes

Abstract Materials like silicon and germanium offer a 10-fold improvement in charge capacity over conventional graphite anodes in lithium-ion batteries but experience a roughly threefold volume increase during lithiation, which challenges ensuring battery integrity. Nanoporous silicon, created by liquid-metal-dealloying, is a potentially attractive anode design to mitigate this challenge, exhibiting both higher capacity and extended cycle lifetimes. However, how nanoporous structures accommodate the large volume change is unknown. Here, we address this question by using phase-field modeling to produce nanoporous particles and to investigate their elastoplastic swelling behavior and fracture. Our simulations show that enhanced mechanical stability results from the network topology consisting of ligaments connected by bulbous, sphere-like nodes. The ligaments forcefully resist elongation while the nodes, behaving like isolated spherical particles, experience large stresses driving fracture. However, being smaller compared to a sphere of the same volume as the entire nanoporous particle, the nodes are more protected against fracture.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Inhomogeneous time-reversal symmetry breaking in Sr 2 RuO 4

We show that the observed time-reversal symmetry breaking (TRSB) of the superconducting state in Sr 2 RuO 4 can be understood as originating from inhomogeneous strain fields near edge dislocations of the crystal. Specifically, we argue that, without strain inhomogeneities, Sr 2 RuO 4 is a single-component, time-reversal symmetric superconductor, likely with d x 2 -y 2 symmetry. However, due to the strong strain inhomogeneities generated by dislocations, a slowly decaying subleading pairing state contributes to the condensate in significant portions of the sample. As it phase winds around the dislocation, time-reversal symmetry is locally broken. Global phase locking and TRSB occur at a sharp Ising transition that is not accompanied by a change of the single-particle gap and yields a very small heat capacity anomaly. Our model thus explains the puzzling absence of a measurable heat capacity anomaly at the TRSB transition in strained samples and the dilute nature of the time-reversal symmetry broken state probed by muon spin rotation experiments. We propose that plastic deformations of the material may be used to manipulate the onset of broken time-reversal symmetry.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

A Data Processing Pipeline To Extract A Knowledge Graph From Heterogeneous Data For Socio-technical Analysis Of Critical Infrastructure Influence

The code is written in Python and consists of the following pipeline that is implemented in Apache Airflow. This pipeline intends to understand the companies that are directly or indirectly involved with a type of critical infrastructure system at some point in that system's lifecycle. The pipeline takes a configuration file that specifies a list of initial companies to consider, a geographic region of interest, and a set of SEC form types as well as other data sources (e.g. CrunchBase) from which to extract entities and relations. There are four main components to this pipeline as currently implemented: Entity Extraction, Network Construction, Analysis, and Visualization. First, Entity Extraction, is implemented as the `topear-extract_organizations` Apache Airflow workflow. Given an initial query that specifies a geographic region of interest and a time interval, the software will extract CI facilities of interest and organizations that have a direct influence relationship to those facilities (e.g. ownership). During the course of the LDRD, we focused on Electric Vehicle charging stations and this information is available via the Department of Energy (DOE) database on fueling stations maintained by NREL. Within the context of the DOE CESER project, we have focused on Battery Energy Storage Systems (BESS). Second, the Network Extraction component will iteratively construct a social network graph given the set of organizations and people extracted in the previous step. Organizations (and eventually People if desired) are then fed as a query to the `topgear-construct_social_network` Apache Airflow workflow which given a set of initial companies and data sets (e.g. SEC EDGAR form types, OpenCorporates, Crunchbase). This Airflow workflow will iteratively query such data sources to discover relationships with new organizations and people. For example, this module can iteratively query SEC EDGAR for metadata that documents the number of each type of form for the given set of companies and their location. This forms metadata represents a catalog of data sources from SEC EDGAR for the extracted social network knowledge graph. The pipeline then downloads these forms from the website and saves them in a build directory for further processing. These documents are then parsed for entities and relations. Again, we note that in additional to SEC data sources, this step can also pull in information on organizations via API services such as CrunchBase and OpenCorporates or bulk data sources. At the end of this step, the resultant social network, the Critical Infrastructure network, and the edges that encode relationships between organizations and CI facilities, form the Adversarial Socio-Technical Network (ASTN) that informs the analysis. Third, the Analysis component processes these generated ASTN. Previously, that has included the ability to compare prevalence of different vendors for a given infrastructure component type across different regions as well as identify common public and private investors across those vendors. This was demonstrated for EV Charging Stations across several different metropolitan areas within an IEEE PES GridEdge publication. More recently, we have looked at ways to identify infrastructure owners and operators of BESS with the most nameplate capacity across different states as well as other indictors of risk resulting from changes in ownership over time. Finally, the Visualization component consists of an HTML/CSS/JS framework by which users can interact geospatial, operational, and organizational relationships across a given portfolio of Critical Infrastructure facilities. The objective is to provide a library of UI/UX modules that can be repurposed for stakeholder-specific dashboards. All of the modules are related via a common event model that enables UI actions in one view to percolate across the other views.

Weaver, Gabriel [Idaho National Laboratory (INL), ↗
DOE OSTI2020

Revisiting the Terawatt Challenge

Richard E. Smalley, in 2003, defined the Terawatt (TW) Challenge as “Adapting our energy infrastructure to simultaneously address diminishing oil resources and rising levels of atmospheric CO 2 .” Smalley, best known for the discovery of C 60 , for which he received the 1996 Nobel Prize in Chemistry, continued to address the challenges of anthropomorphic and natural global energy flows until he passed away in 2005. Smalley challenged the world to transform the energy sector. He envisioned electricity transmitted by high-voltage direct current (DC) lines from massively deployed solar plants in sunny areas and remotely sited nuclear plants. He also envisioned using advanced batteries for local storage of energy. To meet the needs of ~10 people in a world with a dwindling oil supply, Smalley asserted that the world would need to transform its fossil-fuel-driven 14-TW (average power) energy used in 2003 to a largely renewable-energy-driven 30–60 TW (average power) in 2050. This would be possible only if solar-electricity costs could be drastically reduced. The challenges associated with this transition have been called the “Terawatt Challenge.” Fifteen years later, solar-module costs have been reduced by tenfold and annual deployment of solar photovoltaic (PV) modules has grown by a factor of 100,from ~1 gigawatt (GW) in 2004 to ~100 GW in 2018, with a total of 500 GW installed worldwide, producing 2% of the planet’s electricity. As global installed solar generating capacity approaches1 TW, we revisit Smalley’s TW challenge to identify what has changed and quantify the TW Challenge for a baseline scenario and for two scenarios designed as upper and lower bounds determined by the degree we implement electrification and storage. In this paper, we show that the energy choices we make today will dramatically affect the magnitude of future global energy requirements.

SOLAR ENERGY↗
DOE OSTI2020

Replacement of Cobalt in Medical Device Sterilization: Current Trends, Opportunities and Barriers to Adoption of X-ray and E-Beam Within the Medical Device Sterilization Market

Radioactive sources, specifically Co-60, are crucially important to the medical device sterilization industry; however, their benefits must be balanced against the need to ensure that the materials are secure. Accelerator-based sterilization methods, including X-ray and E-Beam, can in many cases sufficiently replace Co-60 and ethylene oxide, the dominant modalities currently in use; however, a lack of hands-on experience with accelerators, regulations, and a lack of capacity have hampered faster adoption of these technologies. The market is likely to change, however, given public pressures against ethylene oxide and concerns over the cost and long-term supply chain robustness of Co-60. This may provide an opportunity for growth for accelerator capabilities. Current research at Sandia National Laboratories and Argonne National Laboratory, on behalf of the Department of Energy’s National Nuclear Security Administration Office of Radiological Security, is focused on developing an understanding of the medical device sterilization marketplace, the different modalities that are used to sterilize goods, and the drivers that affect the actors within it. Research at Pacific Northwest National Laboratory, in conjunction with the medical device sterilization industry, has focused on expanding the industry’s understanding of the capabilities of X-ray sterilization and developing data that can inform the industry’s consideration of a transition towards accelerator-based devices.

62 RADIOLOGY AND NUCLEAR MEDICINE↗
DOE OSTI2020

Powering the Blue Economy: Progress Exploring Marine Renewable Energy Integration With Ocean Observations

The blue economy is a dynamic and rapidly growing movement that captures the interplay between economic, social, and ecological sustainability of the ocean and encompasses numerous maritime sectors and activities (e.g., commerce and trade; living resources; renewable energy; minerals, materials, and freshwater; and ocean health and data). The demand for ocean data to inform scientific, risk reduction, and national security needs is leading to a large increase in the number of deployed ocean observation and monitoring systems, most of which require increased power. Because ocean observation systems are often placed in remote locations, they primarily rely on energy storage (or in some cases in situ energy generation) to power instruments and equipment, which imposes limits on sampling rates, deployment times, and spatiotemporal resolution of data. The U.S. Department of Energy Water Power Technologies Office is exploring the potential for marine renewable energy (MRE) devices (largely wave and tidal energy converters) to provide power to support multiple blue economy opportunities. A portion of these opportunities focus on power at sea markets for providing power in off-grid and offshore locations to support a variety of ocean-based activities, including ocean observation and navigation, underwater vehicle charging, marine aquaculture, marine algae farming, and seawater mining. Initially, research has focused on better understanding how and where MRE can provide a consistent source of reliable power to extend ocean observing missions, including operation of autonomous underwater vehicles. Online surveys as well as phone and inperson interviews were conducted with experts in the field of ocean observing systems and observatories to gather end-user requirements, determine energy needs, identify opportunities for codevelopment, and pinpoint constraints for MRE to meet those needs. The surveys and interviews provided feedback on the potential for powering devices and vehicles using MRE, including identifying common themes and challenges that will inform foundational research and development steps needed to advance the integration of MRE with ocean observing systems. In most cases, additional power generation on the order of watts was identified as significantly beneficial to enhancing ocean observations capabilities.

marine renewable energy, powering the blue economy↗
NASA NTRS1978

Molten Salt Thermal Energy Storage Systems

The feasibility of storing thermal energy at temperatures of 450 C to 535 C in the form of latent heat of fusion was examined for over 30 inorganic salts and salt mixtures. Alkali carbonate mixtures were chosen as phase-change storage materials in this temperature range because of their relatively high storage capacity and thermal conductivity, moderate cost, low volumetric expansion upon melting, low corrosivity, and good chemical stability. Means of improving heat conduction through the solid salt were explored.

Maru, H. C.↗
NASA NTRS1989

Structural and metabolic characteristics of human skeletal muscle following 30 days of simulated microgravity

The effects of simulated microgravity (30 days of continuous 6-deg headdown bedrest, BR) on the structural and metabolic characteristics of human skeletal muscle were determined. Percutaneous needle biopsy samples obtained from the vastus lateralis and soleus muscles before and after the headdown BR were analyzed for histochemical, biochemical and ultrastructual changes. It was found that headdown BR led to decreases in both fast-twitch and slow-twitch fiber areas in both muscles, and there was evidence of remodeling of the ultrastructure in both muscles. The activities of beta-hydroxyacyl-CoA dehydrogenase and citrate synthase were reduced during BR, but phosphofructokinase and lactate dehydrogenase activities did not change. The results indicate that 30-d exposure to simulated microgravity decreased the capacity for aerobic energy supply of human skeletal muscle and led to a disorganization of the contractile machinery.

Hikida, Robert S.↗