Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “cable”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

Virtual Flight Demonstration of the Stratospheric Dual-Aircraft Platform

A baseline configuration for the dual-aircraft platform (DAP) concept is described and evaluated in a physics-based flight dynamics simulations for two month-long missions as a communications relay in the lower stratosphere above central Florida, within 150-miles of downtown Orlando.The DAP configuration features two large glider-like (130 ft wing span) unmanned aerial vehicles connected via a long adjustable cable (total extendible length of 3000 ft) which effectively sail without propulsion using available wind shear. Use of onboard LiDAR wind profilers to forecast wind distributions are found to be necessary to enable the platform to efficiently adjust flight conditions to remain sailing by finding sufficient wind shear across the platform. The aircraft derive power from solar cells, like a conventional solar aircraft, but also extract wind power using the propeller as a turbine when there is an excess of wind shear available.Month-long atmospheric profiles (at 3-5 min intervals) in the vicinity of 60,000-ft are derived from archived data measured by the 50-Mhz Doppler Radar Wind Profiler at Cape Canaveral and used in the DAP flight simulations. A cursory evaluation of these datasets show that sufficient wind shear for DAP sailing is persistent, suggesting that DAP could potentially sail over 90% of the month-long durations even when limited by modest ascent/descent rates.DAP's novel guidance software uses a non-linear constrained optimization technique to define waypoints such that sailing mode of flight is maintained where possible, and minimal thrust is required where sailing is not practical. A set of constraints are identified which result in waypoints that enable efficient flight (i.e., minimal use of propulsion) over the two month-long flight simulations. Waypoint solutions may need to be tabulated for a wide range of potential atmospheric conditions and stored onboard for quick retrieval on a real DAP.DAP's flight control software uses an unconventional mixture of spacecraft and aircraft control techniques. Flight simulations confirms that this controls approach enables the platform to consistently reach successive waypoints over the month-long flight simulations.The ability of DAP to transition between the sailing mode (i.e., cable tension is high) and standard formation flight (i.e., cable tension is low) is a vital capability (e.g., to enable intermittent turns while stationkeeping). A new method to perform these transitions has been identified and characterized with flight simulation which requires special aircraft modifications.The energy-usage of the DAP configuration during two month-long stationkeeping missions over central Florida (i.e., stationkeeping over Orlando) is evaluated and compared to that of a pure solar aircraft of the same weight and aerodynamic performance. DAP is shown to consistently reduce net propulsion usage while simultaneously increasing solar energy capture.A baseline 700 GHz communications system is described and its performance evaluated for the proposed mission over central Florida. It is found that the variable roll orientation of the aircraft would increase the power required to maintain coverage over the stationkeeping radius of 150 miles (e.g., by as much as 100% when DAP is 150 miles from Orlando), compared to level flight. This effect can be mitigated via additional antenna design complexity or a more restricted stationkeeping radius.

Demonstrations↗

Tendon-Actuated Lightweight In-Space MANipulator (TALISMAN) Hinge Joint Structural Performance

The Tendon Actuated Lightweight In-Space MANipulator (TALISMAN), invented and initially developed under the Space Technology Mission Directorate Human Robotics Systems program, is a tendon-actuated robot that established a new structural architecture for long-reach space manipulators. The TALISMAN is designed to have significant stiffness and strength in the plane of the tendons or cables, and operations are designed such that all primary loads are applied in that same plane. However, during normal operations it is possible for out-of-plane forces to be applied on the TALISMAN when secondary loads are imparted by a tool or action at the wrist. These secondary loading conditions will induce out-of-plane bending loads in the TALISMAN hinge joints. The TALISMAN hinge joints must be designed for these out-of-plane loads, to ensure no failure of the joint occurs during operations. A series hinge joint out-of-plane stiffness tests were conducted at five different joint angles; at three cable pre-loads from 25-lbf to 100-lbf; up to an equivalent out-of-plane tip load of 27.28-lbf at the end of a 51-in. long distal link. The objective of the tests was to provide an initial set of deflection, cable load, and strain data to inform accurate modeling of the hinge joint out-of-plane stiffness. The test objective was achieved by developing an FEM of the hinge joint able to predict tip displacement to within 10% of values measured in tests. The hinge joint FEM may now be implemented into a full-scale analysis model of the TALISMAN V2.0 to provide predictions of out-of-plane displacement under different load and joint angle conditions.

Matthew K Mahlin↗

Feasibility of Powerline Communications (PLC) on Future Spacecraft: EMI/EMC Test Results on COTS PLC Technology

Cable harnessing mass continues to be a problem for spacecraft development, particularly with increasingly complex payloads and constraints to their mass and costs. As a strategic initiative to reduce cable harnessing on flight missions, NASA JPL’s Powerline Communications (PLC) research and technology development (R&TD) effort investigates the ability to combine power and data onto the same cable conductors. Research and development of PLC technology, including testing of commercial off-the-shelf (COTS) modules and design of custom PLC unit, aim to articulate the opportunity to infuse this technology into NASA flight projects. This paper illustrates the feasibility of Powerline Communications on future spacecraft through Electromagnetic Interference/Compatibility (EMI/EMC) testing on COTS PLC components including conducted emissions and susceptibility as well as radiated emissions and susceptibility.

Mitchell, Andrew W.↗

Scalability and Design of Six Rod Tensegrity Soft Robotic Structure

Robots based on tensegrity structures (interconnected rods and cables) offer many advantages such as low weight, small volume when packed, and have high impact resistance. Unfortunately tensegrity robots can be difficult to make and scale due a fundamental design trade-off: they need to have enough tension in the structure to maintain its integrity, while not having so much tension that it is difficult to actuate,change shape and move. This paper addresses this issue with three approaches:1) Traction based pulley actuation that is less sensitive to the tensioning of the structure, 2) A mix of elastic and inelastic cables allowing for a better balance between tensioning and actuation and 3) Using flexible rods allowing for actuation with inelastic cables. We test configurations and show that these approaches can indeed increase the scalability and usefulness of tensegrity robots.

Tensegrity↗

Rimmed Wheel Performance on the Mars Science Laboratory Scarecrow Rover

The Mars Science Laboratory (MSL) Curiosity rover experienced increasing wheel damage beginning in October 2013. While the wheels were designed to operate with considerable damage, the rate at which damage was occurring was unexpected and raised concerns regarding wheel life expectancy. As of Sol 2555 (10-14-19), there are two broken grousers on the left middle wheel, and one broken grouser on the right middle wheel. One possible scenario, albeit remote, is that enough grousers break on a wheel such that unconstrained portions of the wheel could contact the cable running from the rover motor controller assembly to the wheel's drive actuator. If the cable to a drive actuator is damaged, that wheel may no longer respond to commands. To make progress towards a navigation goal position, that wheel would need to be dragged. To mitigate the risk of damaging a cable running to a wheel’s drive actuator, the unconstrained portion of a wheel could be strategically shed by performing driving maneuvers on an immovable rock. What would remain after wheel shedding is a rimmed wheel (the outer 1/3 of the wheel). We studied the feasibility of remotely commanding the rover to perform the shed maneuver on one of its front wheels. To inform whether or not to shed the wheels, we tested the performance of driving on one or more rimmed wheels in flight. This led to a two-month test campaign in the Jet Propulsion Laboratory (JPL) Mars Yard using the Scarecrow testbed rover. Driving and steering performance was characterized on a variety of terrain types and slopes in a worst-case rimmed wheeled configuration. Test results indicate that if wheel shedding could be successfully executed in flight, Curiosity could continue to drive indefinitely on rimmed wheels.

Graser, Evan↗

Novel Processing, Testing and Characterization of Copper/Carbon Nanotube (Cu/CNT) Yarn Composite Conductor

Sustainable electrified aircraft propulsion (EAP) is likely to lead to an increase in the electrical wiring contained within a single aircraft. Since the electrical resistance and mass of copper (Cu) conductors are associated with power losses, it is desirable to design high-conductivity lightweight conductor materials, thus reducing the mass of components like motor windings, low-voltage signal cables, and transmission cables for data and power to improve the overall energy efficiency. This paper describes a unique framework for manufacturing metalized carbon nanotube (CNT) composite conductors, measuring their electrical conductivity and strength, and modeling the overall conductivity and current sharing within such composites. Tensile testing was conducted on the processed composite conductor cables with the use of acoustic emission and electrical resistivity to determine stress-dependent-failure mechanisms while monitoring the electrical conductivity. The average of measured electrical conductivities of annealed Cu/CNT samples from batch 5 was greater than theoretical predictions by 9.8 percent and was also greater than the conductivity of pure annealed Cu by 4.8 percent and had comparable ultimate tensile strengths. Additionally, those Cu/CNT samples provide a 13.5% weight saving over current state of the art copper wires. Theories explaining improved intrinsic conductivity are discussed.

Metalized CNT↗

Transient Structure Current Generated by the Activation of a Squib Device

Experimental measurements of the currents in pyro-activation circuits show that a structure current is generated during the pyro-activation process. This current is a transient current and is an intense source of electromagnetic interference. Analysis has indicated that the noise voltage induced on candidate victim circuits is sufficient to cause circuit upset and/or latchup. A survey of flight anomaly records has also correlated the occurrence of anomalies with the pyro-activation process. Detailed analyses, taking the spacecraft cabling configuration and circuit sensitivities into account, have shown that the structure current induced noise voltage could definitely be the cause of the anomalies. The threat of the structure current due to pyro-activation can be alleviated by isolating the pyro-activation circuit from ground and by proper arrangement of the cables in sensitive circuits.

pyrotechnic↗

Flex-Capsules for the Roman Space Telescope High Gain Antenna Gimbal

The Cable Wrap mechanism has been traditionally used for feeding power and telemetry through each gimbal actuator exiting at the gimbal output flange. Such a mechanism had often utilized round wire bundles or a multitude of single insulated conductors woven together flatwise to handle the angular rotation. Though flexible printed circuit board (PCB) is not a new technology, it was decided to implement it for the Roman Space Telescope (RST) High Gain Antenna Gimbal in an effort to improve reliability with consistency of manufacture and to save mass and minimize required volume. This paper provides a description of what we term Flex-Capsule (a similar vendor flight development is termed Twist Capsule), discusses the reasoning behind choosing a new engineering development over maintaining heritage, and includes commentary pertaining to life cycle analysis, electrical performance, and flexible PCB lubrication. Lessons learned from the design, analysis, and test campaign are also included. The conclusion is that benefits of pursuing the Flex-Capsule over heritage Cable Wrap have been realized.

twist capsule↗

Flex-Capsule for the Roman Space Telescope High Gain Antenna Gimbal

The Cable Wrap mechanism has been traditionally used for feeding power and telemetry through each gimbal actuator exiting at the Gimbal output flange. Such a mechanism had often utilized round wire bundles, or a multitude of single insulated conductors woven together flatwise to handle the angular rotation. Though flexible printed circuit board (PCB) is not a new technology, it was decided to implement it for the Roman Space Telescope (RST) High Gain Antenna Gimbal in an effort to improve reliability with consistency of manufacture and to save mass and minimize required volume. This paper provides a description of what we term Flex-Capsule (a similar vendor flight development is termed Twist Capsule), discusses the reasoning behind choosing a new engineering development over maintaining heritage, and includes commentary pertaining to life cycle analysis, electrical performance, and flexible PCB lubrication. Lessons learned from the design, analysis, and test campaign are also included. The conclusion is that benefits of pursuing the Flex-Capsule over heritage Cable Wrap have been realized.

twist capsule↗

Quick-attach clamp

Clamp of the slideable jaw type can be applied to moving lines such as cables or ropes. The clamp has a trigger-operated jaw that can be attached to a redrop parachute on a moving tow cable. The trigger mechanism maintains the jaws retracted in the housing until they are released for clamping.

Vano, A. E.↗

High-field superconducting nested coil magnet

Superconducting magnet, employed in conjunction with five types of superconducting cables in a nested solenoid configuration, produces total, central magnetic field strengths approaching 70 kG. The multiple coils permit maximum information on cable characteristics to be gathered from one test.

Laverick, C.↗

Catheter transducer and circuit

Simple integrated circuit located at transducer, enables use of single coaxial cable for both input and output connections. Circuit is sensitive to changes in RC time constant, has much improved sensitivity characteristics, and is unaffected by changes in cable capacitance effects.

Harrison, D. R.↗

Rotary stripper for shielded and unshielded FCC

Rotary stripper removes narrow strips of insulation and shielding to any desired depth. Unshielded cables are stripped on both sides with one stroke, shielded cables are stripped in steps of different depths.

Angele, W.↗

Future development of instructional television

The use of television in schools as an aid to instruction is proposed for individualized instruction, repetition for slow learners, acceleration for fast learners, and lectures from the best teachers for all students. A dedicated school district cable system, a 40 channel cable to each school and classroom, is considered. This innovation offers an opportunity for improving the quality and content of the school's instruction and for reducing the cost.

Barnett, H. J.↗

A preliminary study of containment concepts for aircraft landing on elevated STOL-ports

A preliminary study of containment systems for aircraft landing on elevated STOL-ports was conducted as part of an overall study of human acceptance problems associated with STOL operations. The study included a survey and feasibility study of different concepts and a computer analysis of four arrestment systems. The principal conclusion was that a system referred to as the FAA system appears to offer the greatest promise. In this system, standard arresting gear cables are stretched across the roof-top, at roughly 100-foot intervals, but are shielded over the 100-foot-wide primary landing strip. Thus a pilot can land with an arresting hook down, but will not contact the cable unless he swerves off the landing strip, either because he has made a bad landing, or because his landing gear has failed. It was also noted that a suitable curb or guard rail should be developed. Presently available arresting gears and nylon net barriers were considered satisfactory for the overshoot problem.

Haviland, J. K.↗

A vacuum chamber feedthrough

Simple and inexpensive microwave feedthrough has been designed which transfers 130 ns, 5kV pulse into vacuum chamber. Feedthrough may be used over wide range and is adaptable to most coaxial cables, since either multistrand or single strand center conductor cable can be used.

Brown, V. D.↗

An investigation of a movable mass-attitude stabilization system for artificial-G space

The application of a single movable mass to generate control torques for the attitude control of space vehicles is discussed. The feasibility of a movable mass control in stabilizing a cable-connected, artificial gravity configuration is proposed. A dynamic model for cable-connected configurations to account for the aggregate motion of the space station and relative torsional motion between the crew quarters and counter weight is developed.

Childs, D. W.↗