Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “binder”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

Fuel Cell Membrane Electrode Assemblies with Ultra-Low Pt Nanofiber Electrodes (Final Report)

H 2 /air fuel cell membrane-electrode-assemblies (MEAs) were fabricated with electrospun particle/polymer nanofiber mat cathodes (0.1 mg Pt /cm 2 or 0.2 mg Pt /cm 2 Pt/C, PtCo/C or PtNi/C) and anodes (0.1 mg/cm 2 Pt/C), where the binder was a mixture of acid-form perfluorosulfonic acid ionomer (e.g., Nafion™) and poly(acrylic acid) (PAA) carrier polymer or sodium-form PFSA with a carrier polymer of either PAA or polyethylene oxide (PEO). For the latter two cases, the water-soluble carrier was removed from the fibers after electrospinning. MEAs with Pt/C anode/cathode catalyst loadings of 0.1 mg Pt /cm2 each, an 1100 EW PFSA binder (Nafion™ dispersion), and a Nafion 211 membrane produced high power at both high and low relative humidity (RH) conditions, e.g., a maximum power density of 919 mW/cm 2 at 100% RH and 832 mW/cm 2 at 40% RH for a test at 80 °C and 200 kPa abs . The high power at low RH was attributed to nm-size pores within the fibers that trap water via capillary condensation thus maintaining a high proton conductivity of the PFSA binder in the cathode and especially the anode while minimizing/eliminating ionic isolation of catalyst particles in low water content, poorly conductive binder. At the same time, micro-porosity between fibers in the cathode allows for fast removal of electrogenerated water, thus minimizing cathode flooding. Nanofiber MEAs with Pt alloy catalyst cathodes also performed well, where a fibrous PtCo/C catalyst cathode at a loading of 0.1 mg/cm 2 produced 20% more power than a conventional powder cathode MEA, e.g., a maximum power density of 1,045 mW/cm 2 vs. 869 mW/cm 2 at 80 °C, 100% RH, and 200 kPa abs , and a PtNi/C fiber cathode MEAs prepared with Na+-form Nafion + PEO generated a maximum power of 820 mW/cm 2 at 40% RH. Fiber electrode MEAs with a neat Nafion binder (prepared from Na+-form Nafion + PEO or PAA) where the cathode Pt loading was ~0.1 mg/cm 2 exhibited a 25% loss in maximum power at 30,000 metal dissolution cycles, as compared to a 12% loss when the cathode binder was H+-form Nafion + PAA. The performance of a fiber mat electrode MEA with Pt/C catalyst (0.2 mg/cm 2 cathode loading and 0.1 mg/cm 2 anode loading) was excellent. At 80 oC and 200 kPa abs , the maximum power density was 1104 mW/cm 2 . The maximum power was independent of feed gas humidity for 40 < RH < 100%. The power loss after a metal dissolution AST (30,000 voltage cycles) was only 13%.

08 HYDROGEN↗

Organic Solvent Free Process to Fabricate High Performance Silicon/Graphite Composite Anode

Cycling stability is a key challenge for application of silicon (Si)-based composite anodes as the severe volume fluctuation of Si readily leads to fast capacity fading. The binder is a crucial component of the composite electrodes. Although only occupying a small amount of the total composite mass, the binder has major impact on the long-term electrochemical performance of Si-based anodes. In recent years, water-based binders including styrene-butadiene rubber (SBR) and carboxymethyl cellulose (CMC) have attracted wide research interest as eco-friendly and low-cost alternatives for the conventional poly(vinylidene difluoride) (PVDF) binder in Si anodes. In this study, Si-based composite anodes are fabricated by simple solid mixing of the active materials with subsequent addition of SBR and CMC binders. This approach bypasses the use of toxic and expansive organic solvents. The factors of binder, silicon, and graphite materials have been systematically investigated. It is found that the retained capacities of the anodes are more than 440 mAh/g after 400 cycles. These results indicate that organic solvent free process is a facile strategy for producing high performance silicon/graphite composite anodes.

Fang, Chen (ORCID:0000000321011991)↗

On The Development of Additive Construction Technologies for Application to Development of Lunar/Martian Surface Structures Using In-Situ Materials

For long-duration missions on other planetary bodies, the use of in-situ materials will become increasingly critical. As man's presence on these bodies expands, so must the breadth of the structures required to accommodate them including habitats, laboratories, berms, radiation shielding for natural radiation and surface reactors, garages, solar storm shelters, greenhouses, etc. Planetary surface structure manufacturing and assembly technologies that incorporate in-situ resources provide options for autonomous, affordable, pre-positioned environments with radiation shielding features and protection from micrometeorites, exhaust plume debris, and other hazards. This is important because gamma and particle radiation constitute a serious but reducible threat to long-term survival of human beings, electronics, and other materials in space environments. Also, it is anticipated that surface structures will constitute the primary mass element of lunar or Martian launch requirements. The ability to use in-situ materials to construct these structures will provide a benefit in the reduction of up-mass that would otherwise make long-term Moon or Mars structures cost prohibitive. The ability to fabricate structures in situ brings with it the ability to repair these structures, which allows for self-sufficiency necessary for long-duration habitation. Previously, under the auspices of the MSFC In Situ Fabrication and Repair (ISFR) project and more recently, under the joint MSFC/KSC Additive Construction with Mobile Emplacement (ACME) project, the MSFC Surface Structures Group has been developing materials and construction technologies to support future planetary habitats with in situ resources. One such technology, known as Contour Crafting (additive construction), is shown in Figure 1, along with a typical structure fabricated using this technology. This paper will present the results to date of these efforts, including development of novel nozzle concepts for advanced layer deposition using the Contour Crafting process. This process, conceived initially for rapid development of cementitious structures on Earth, also lends itself exceptionally well to the automated fabrication of planetary surface structures using minimally processed regolith as aggregate, and imported binder material or binders developed from in situ materials. This process has been used successfully in the fabrication of construction elements using lunar regolith simulant and Mars regolith simulant, both with various binder materials. These binder materials have resulted from extensive evaluation and include both "imported" binder materials that might be launched from Earth as well as some binder materials that can theoretically also be derived from existing regolith materials. They were chosen to 1) reduce penetrating radiation as much as possible, primarily with hydrogen-bearing polymers, 2) attempt to provide an air-tight structure, 3) sufficiently mix and adsorb to regolith grains for strength, 4) maximize tolerance to day-night thermal cycling, 5) possibly increase electrical conductivity to dissipate any accumulated static charge, and 6) ease their application on planetary surfaces (specifically, the accommodation of reduced atmosphere and lack of heat sinks). Some of these materials have been tested with respect to radiation mitigation, micrometeorite resistance, and resistance to larger, slower-traveling pieces of regolith impinging on the surface, simulating nearby launch and landing activities. Conceptual designs for a Continuous Feedstock Delivery/Mixing System (CFDMS) will also be presented and future planned activities will be discussed as well.

Werkheiser, Niki↗

Predicting sintering window during supersolidus liquid phase sintering of steels using feedstock analysis and CALPHAD

Binder jet 3D printing results in carbon pickup from the binder at the inter-particle regions during binder burnout. The excess carbon lowers the solidus temperature of the green part locally during supersolidus liquid phase sintering (SLPS). Currently, thermodynamic calculations rely on the use of bulk powder compositions to predict the sintering window. This can overestimate the sintering temperature since the local increase in carbon on powder surfaces is not accounted for, that can locally lower the solidus temperature during SLPS. Here we show that using the inputs from feedstock and binder analysis, the excess carbon and hence the sintering window for the alloy can be predicted using CALPHAD. We present a case study on applying the proposed approach for pressureless sintering of binder jet additive manufactured (BJAM) of H13 steel via SLPS.

36 MATERIALS SCIENCE↗

Gas Retention in an HMX-based Explosive (LX-14)

In previous studies, we found that the nitroplasticizer in the HMX-based explosive PBX 9501 played a crucial role in cookoff, especially when predicting response in larger systems. We have recently completed experiments with a similar explosive, LX-14, that has a relatively nonreactive binder. We expected the ignition times for LX-14 to be longer than PBX 9501 since PBX 9501 has a more reactive binder. However, our experiments show the opposite trend. This paradox can be explained by retention of reactive gases within the interior of LX-14 by the higher strength binder resulting in faster ignition times. In contrast, the binder in PBX 9501 melts at low temperatures and does not retain decomposition gases as well as the LX- 14 binder. Retention of reactive gases in LX-14 may also explain the more violent response in oblique impact tests when compared to PBX 9501.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Measurement of porosity in a composite high explosive as a function of pressing conditions by ultra-small-angle neutron scattering with contrast variation

We have used ultra-small-angle neutron scattering (USANS) with contrast variation to measure the porosity (voids and binder-filled regions) in a composite high explosive, PBX 9501, formulated with a deuterated binder. Little is known about the microstructure of pressed PBX 9501 parts and thus how it is affected by processing. Here, we explore the effect of varying the pressing intensity on the PBX 9501 microstructure. Disk-shaped samples of PBX 9501 were die-pressed with applied pressures ranging between 10,000 and 29,000 psi at 90 C. Five samples were prepared at each pressure that differed in the fraction of deuterated binder, facilitating variation of the neutron scattering length density contrast ({Delta}{rho}) and thus, the resolution of microstructural details. The sample composition was determined by calculation of the Porod Invariant as a function of {Delta}{rho} and compared with compositional estimates obtained from the bulk sample density. Structural modeling of the USANS data, at different levels of contrast, assuming both spherical and cylindrical morphologies, allowed the mean size and size distribution of voids and binder-filled regions to be determined. A decrease in the mean diameter of binder-filled regions was found with increasing pressing intensity, while the mean void diameter showed no significant change.

36 MATERIALS SCIENCE↗

Migration of Al within dealuminated beta extruded catalysts influences olefin distribution during ethanol upgrading

Zeolites serve as essential catalytic platforms for many industrial processes, including emerging ethanol-to-olefins (ETO) upgrading technologies. Although metal-loaded (Cu, Zn, Y) dealuminated beta (deAlBeta) zeolite powders are promising catalysts for direct ETO conversion with high selectivity to butene-rich C3+ olefins necessary for production of sustainable aviation fuels (SAF), development of these materials as shaped technical bodies through the incorporation of binders is required for scale-up and commercial viability. Here, we report the ethanol upgrading performance of Cu-Zn-Y/deAlBeta extruded catalysts formulated with either alumina or kaolin clay binders. Both extrudates exhibit high ethanol dehydration reactivity which competes with the initial ethanol dehydrogenation step in the direct ETO reaction network. Consequently, elevated selectivity to dehydration side products (ethylene, diethyl ether) at ∼100% ethanol conversion is observed on Cu-Zn-Y/deAlBeta extrudates compared to the powder catalyst, which inhibits production of desired C3+ olefins. Utilizing microscopy and spectroscopic characterizations, we attribute this to Al migration from binder to zeolite particles within the extrudates, thus re-aluminating the zeolite and generating Brønsted acid sites active for dehydration reactions. This work elucidates the effects of binder incorporation on ETO product distributions and emphasizes that binder selection must be carefully considered during design of extruded zeolite catalysts.

Jacobs, Hunter [ORNL] (ORCID:000000016190874X)↗

Highly dense, inexpensive composites via melt infiltration of Ni into WC/Fe preforms

Generally, WC-based composites use Co as the metal binder phase to consolidate using liquid-phase sintering with a small percentage of Co, but a potentially lower cost binder phase can be made with a different approach when using large amount of metal binder phase. FeNi as a metal binder material is much cheaper than Co. WC can be liquid-phase sintered and melt infiltrated with FeNi, but by making FeNi in situ , costs lower even further. Composites of WC-(Fe-Ni) were made by first pressing a mixture of WC and Fe powders and subsequently melt infiltrating Ni in an amount corresponding to less volume than the porosity of the preform to ensure high WC content. The research objective was to make highly dense composites via melt infiltration with a low-cost metal binder phase in situ . This approach has the potential to make fully dense composites, rather than hardmetals, with suitable properties at lower costs. The density and hardness are 97.4%TD and 6.72 GPa, respectively.

36 MATERIALS SCIENCE↗

Chromium segregation at phase boundaries in Cr-doped WC-Co cemented carbides

Highlights: • Experimental evidence of a mixed (W,Cr) carbide layer on WC grain surfaces • Evidence of Cr segregation in the Co-rich binder phase in front of WC grain surfaces • Temperature dependent equilibrium segregation of Cr estimated from atom probe data • Experimental observations supported by predictions from thermodynamic modelling - Abstract: Atom probe tomography has shown (Cr,W)C to be present as a thin WC grain surface layer in an as-sintered Cr-doped WC-Co cemented carbide microstructure slowly cooled from the sintering temperature. The Co-rich binder phase contained a segregation of Cr in front of this surface layer. The mixed carbide layer was not observed when the as-sintered material had been heat treated at 1000 °C for 3000 s and then quickly cooled. A reduced amount of segregated Cr was, however, still present in the binder phase in front of the WC grain surface. These observations are supported by predictions from thermodynamic modelling; (Cr,W)C becomes stable at temperatures below 940 °C in the absence of other secondary carbides. The equilibrium segregation of Cr in the binder phase was estimated to 0.8 and 0.4 monolayer in the as-sintered and heat treated materials, respectively. The energy of segregation was calculated to 0.22 eV/Cr atom from the atom probe data. This value would result in a Cr segregation of 0.3 monolayer at the sintering temperature 1410 °C, provided that the energy of segregation in the Co-rich liquid phase sintering medium is the same as in the Co-rich binder phase. This Cr segregation may explain the WC grain growth inhibiting effect of Cr additions to WC-Co cemented carbide materials.

36 MATERIALS SCIENCE↗

Molecular Mechanisms Underlying Surfactant-Based Plastics De-Inking

Surfactant-mediated binder removal is critical for de-inking pretreatment in plastics recycling, yet the molecular mechanisms governing surfactant performance remain poorly understood. We used all-atom (AA) and coarse-grained (CG) molecular dynamics (MD) simulations alongside alkaline surfactant washing experiments to investigate interactions between a series of surfactants and a polyether urethane (PEU) binder in solution and on a polyethylene (PE) surface. Experiments reveal a range of de-inking efficiencies, ranging from <25 to >95% depending upon surfactant headgroup charge and tail length. AA simulations reveal that charged surfactants reach stable levels of surfactant coverage, while nonionic surfactants aggregate on the binder. CG umbrella sampling calculations quantify the thermodynamics of binder desorption in water. In ∼0.25 M surfactant solutions, up to a 52% reduction in the free energy barrier is computed, with trends in good agreement (R 2 = 0.92, Pearson’s r = –0.96, Spearman’s ρ = –0.83) with experimental de-inking efficiencies. We find that charged surfactants are more effective than nonionic surfactants for de-inking and propose three regimes of surfactant de-inking processes: good de-inking occurs in surfactants that promote PEU desorption with a low radius of gyration (R g ); moderate de-inking occurs when surfactants stabilize PEU but increase R g ; poor de-inking occurs in surfactants that aggregate on the binder and promote extensive anchoring to the surface. Overall, these molecular-level insights have the potential to guide the design of surfactant formulations for plastics recycling applications.

ink removal↗

Algae Asphalt to Enhance Pavement Sustainability and Performance at Subzero Temperatures

This paper evaluates the potential of algae-derived biobinders as sustainable alternatives for pavement construction. It specifically examines the physicochemical and rheological properties of biomodified binders and their potential to offset carbon emissions when used as partial replacements for conventional petroleum-based asphalt binders. Biosequestration of CO 2 using microalgal cell factories is a promising way of recycling CO 2 into biomass via photosynthesis. Our study demonstrates that incorporating algae-derived binders into asphalt can significantly reduce carbon emissions. Each 1% increase in algae-based biobinder leads to an approximate 4.5% decrease in net carbon emissions. This indicates that a blend containing about 22% biobinder has the potential to achieve carbon neutrality. Blends with higher proportions may even result in net-negative emissions, highlighting a promising strategy for environmentally responsible road construction. In terms of performance, the study shows that certain algae-derived biobinders significantly enhance the cracking resistance of asphalt, particularly under subzero temperatures, by improving its stress-relief capacity. A key contribution of this work is the introduction of polarizability as a novel molecular-level parameter for assessing the compatibility of algae-derived bio-oils with asphalt. By capturing the electronic responsiveness of bio-oil molecules, polarizability serves as a predictive indicator of their interaction potential with asphalt components, providing a new dimension for evaluating the binder performance at the molecular scale. Among the tested materials, the biobinder derived from Haematococcus pluvialis demonstrated particularly strong improvements in resistance to permanent deformation under repeated loading conditions analogous to traffic-induced stress, as well as enhanced resistance to moisture-induced damage. In conclusion, these findings advance the chemistry-driven design of biomass-based binders and highlight a promising pathway toward the development of low-carbon, high-performance, and sustainable infrastructure materials.

Algae↗

High-Performance Screen-Printed Thermoelectric Films on Fabrics

Printing techniques could offer a scalable approach to fabricate thermoelectric (TE) devices on flexible substrates for power generation used in wearable devices and personalized thermo-regulation. However, typical printing processes need a large concentration of binder additives, which often render a detrimental effect on electrical transport of the printed TE layers. Here, we report scalable screenprinting of TE layers on flexible fiber glass fabrics, by rationally optimizing the printing inks consisting of TE particles (p-type Bi 0.5 Sb 1.5 Te 3 or n-type Bi 2 Te 2.7 Se 0.3 ), binders, and organic solvents. We identified a suitable binder additive, methyl cellulose, which offers suitable viscosity for printability at a very small concentration (0.45–0.60 wt.%), thus minimizing its negative impact on electrical transport. Following printing, the binders were subsequently burnt off via sintering and hot pressing. We found that the nanoscale defects left behind after the binder burnt off became effective phonon scattering centers, leading to low lattice thermal conductivity in the printed n-type material. With the high electrical conductivity and low thermal conductivity, the screen-printed TE layers showed high room-temperature ZT values of 0.65 and 0.81 for p-type and n-type, respectively.

36 MATERIALS SCIENCE↗

Effect of PBX prill size on the compressive properties of PBX 9502

Plastic-Bonded Explosive (PBX) prills are agglomerates a few millimeters in diameter composed of High Explosive crystals non-uniformly distributed in and surrounded by a polymer binder. When pressed at elevated temperatures at or above the binder melt temperature the polymer flows to uniformly coat the HE crystals to create a well-consolidated compaction. In reality it does so imperfectly, such that x-ray tomographic scans often look like a collection of prills mashed together. It is speculated that the larger the prill, the more non-uniform the binder distribution, but this has never been proven. Even if that were not so, the larger the prill the farther binder must flow toward the middle to homogenize during pressing. Thus, the degree of homogenization depends in part on prill size. The degree to which binder flows during pressing in turn affects the void distribution within pressed charges, which one suspects will affect shock sensitivity and material strength. In this paper we explore, for ~30 PBX 9502 formulation batches using the same TATB powder lot, how prill size affects the compressive mechanical properties.

36 MATERIALS SCIENCE↗

X-Ray Diffraction of Slag-Based Sodium Salt Waste Forms

Cementitious materials are used to solidify and stabilize aqueous based radioactive waste containing sodium salts. The types and proportions of cementitious ingredients used to treat aqueous radioactive waste streams containing sodium salts depend on the performance objectives for the waste forms and the compositions of the waste streams. Matrix phases can stabilize certain contaminants (co-precipitation, substitution, ion exchange, and / or sorption), influence processing properties, and are responsible for physical properties and durability of the cured waste forms. Consequently, characterization of the matrix (binder) mineralogy (chemical compositions and crystalline / non crystalline structures) is important for predicting contaminant leaching and evolution of the materials as a function of time and changing conditions This report documents sample preparation and x-ray diffraction results for a series of mixtures of sodium salt waste and cementitious binders. The objective of this study was to provide initial phase characterization for the CBP reference case cementitious salt waste form. This information can be used to: 1) generate a base line for the evolution of the waste form as a function of time and conditions, 2) potentially to design new binders based on mineralogy of the binder, 3) understand and predict anion and cation leaching behavior of contaminants of concern, and 4) predict performance of the waste forms for which phase solubility and thermodynamic data are available. Characterization of the mineralogy is also important for understanding the buffering effects that the waste form has on infiltrating water / leachates. More specifically, identification of hydrated phases capable of sequestering anions in the structures and crystallinity of the calcium silicate binder phases were of particular interest. The intent was to use this characterization data as a starting point for more detailed phase characterization using neutron diffraction techniques in addition to quasi-elastic neutron scattering techniques for characterization of water at the ORNL Spallation Neutron Source, Oak Ridge, TN. The initial characterization is complete. Due to extensive substitutions of cations and anions in the layered double hydroxide phases and the very fine intermixing of poorly crystalline hydrated phases in the reference case blend (10 : 45 : 45 cement : slag : fly ash), electron diffraction and transmission electron spectroscopy are recommended as the next step for characterization. In summary, the hydrated mixtures of Type II portland cement, Grade 100 ground granulated blast furnace slag (GGBFS) and carbon burn-out (CBO) Class F Fly ash contained hydrated phase assemblages which were typical of those reported in the literature. Based on x-ray diffraction results, no significant differences were detected in samples cured 2 months and 14 months in sealed containers at ambient indoor temperatures.

36 MATERIALS SCIENCE↗

Accelerated Testing of Selected Filler Compositions

The fillers R&D program, mostly experimental, is part of a broader R&D program that includes new process modeling and performance assessment of criticality effects and the overall importance of criticality to repository performance (consequence screening). A literature research and consultation effort with experts by Hardin and Brady (2018) identified several potentially effective and workable filler materials including cements (primarily phosphate based), molten-metal alloys, and low-temperature glasses. Filler attributes were defined and the preliminary lists were compared qualitatively. Further comparative analysis will be done (e.g., cost estimates) after experimental screening has narrowed the list of alternatives. The following cement filler compositions were selected for experimental development work and accelerated testing in FY19: Aluminum phosphate cements (APCs); more specifically aluminum oxide / aluminum phosphate (Al 2 O 3 / AlPO 4 ) cements in which Al 2 O 3 serves as the filler material bound by an AlPO 4 binder formed by the reaction of Al 2 O 3 with H 3 PO 4 ; Calcium phosphate cements (CPCs); more specifically composed of pure or nearly pure hydroxyapatite (Ca 5 (PO 4 ) 3 (OH)); Magnesium potassium phosphate cements (MKPs) composed of magnesium oxide / magnesium potassium phosphate (MgO / MgKPO 4 ) cements in which MgO serves as the filler and MgKPO 4 serves as the binder formed by the reaction of MgO with monopotassium phosphate (KH 2 PO 4 ) and tricalcium phosphate ((Ca 3 (PO 4 ) 2 ); Two additional potential cement materials were explored preliminarily as the result of: (1) continued literature investigations into other filler candidates (wollastonite-based phosphate ceramic) and (2) the experimental discovery of a well-consolidated fly ash phosphate cement during the evaluation of fly ash as a potential filler material with Al 2 O 3 in APCs. Fly ash phosphate cements, more specifically in which a fly ash material composed primarily of mullite and quartz serves as the filler and is reacted with H 3 PO 4 to form amorphous phosphate phase(s) as the binder; Wollastonite aluminum phosphate cements (WAPC), specifically wollastonite / aluminum phosphate (CaSiO 3 / AlPO 4 ) in which CaSiO 3 serves as the filler material and AlPO 4 serves as the binder formed by Al(OH) 3 or metakaolin as Al sources and H 3 PO 4 or ammonium dihydrogen phosphate (ADP) (NH 4 H 2 PO 4 ) as phosphate sources. The FY19 effort focused on the optimization of compositions and subsequent processing of these five materials to achieve dense and well-consolidated monolithic samples with relatively low porosity. Once these goals were met basic material properties screening evaluations were performed including an assessment of dissolution resistance in water at elevated temperature (200 °C) and mechanical testing including unconfined compressive strength (UCS) testing. To date, the aluminum phosphate cements (APCs) appear to show the most promise for continued development. They are easily prepared and form smooth pourable slurries that remain stable for days with relatively low viscosities of several thousand centipoise (cP). They are then set at elevated temperatures (e.g., 170 °C) under ambient (0.1 MPa) or elevated pressure (~1MPa). Overall, they demonstrate the best dissolution resistance in water at elevated temperature (200 °C) and good compressive strengths. However, additional effort is required to optimize the APC slurry formulations and the process used for thermal curing these materials. The calcium phosphate cements (CPCs) can be formed at room temperature to produce a well-consolidated body. However, their slurry viscosities are very high (and difficult to measure) and they exhibit relatively short cure times of 2 to 3 hours. Also, dissolution resistance is very poor, the poorest of all the cements examined The same is the case for the small number of MKP cements fabricated; they cure very quickly (10 minutes or less) and disintegrate within a few hours upon immersion in distilled water. Surprisingly, fly ash reacts with phosphoric acid to form dense and well-consolidated cements but the mixture rapidly sets at room temperature (less than 30 minutes) and the subsequent conversion of the binder to an amorphous phosphate phase(s) as a function of temperature is complicated. Finally, the wollastonite aluminum phosphate cements (WAPC) are easily prepared and form smooth pourable slurries that remain stable for several hours. They are then set at 130 °C. A WAPC sample exhibited the highest compressive strengths of all the materials we evaluated but in general their dissolution resistance to water is poor.

36 MATERIALS SCIENCE↗

Effect of PBX Prill Size on the Compressive Properties of PBX 9502

Plastic-Bonded Explosive (PBX) prills are agglomerates a few millimeters in diameter composed of High Explosive crystals non-uniformly distributed in and surrounded by a polymer binder. When pressed at elevated temperatures at or above the binder melt temperature the polymer flows to uniformly coat the HE crystals to create a well-consolidated compaction. In reality it does so imperfectly, such that x-ray tomographic scans often look like a collection of prills mashed together. It is speculated that the larger the prill, the more non-uniform the binder distribution, but this has never been proven. Even if that were not so, the larger the prill the farther binder must flow toward the middle to homogenize during pressing. Thus, the degree of homogenization depends in part on prill size. The degree to which binder flows during pressing in turn affects the void distribution within pressed charges, which one suspects will affect shock sensitivity and material strength. In this paper we explore, for ~30 PBX 9502 formulation batches using the same TATB powder lot, how prill size effects the compressive mechanical properties.

36 MATERIALS SCIENCE↗

Proton conducting membrane using a solid acid

A solid acid material is used as a proton conducting membrane in an electrochemical device. The solid acid material can be one of a plurality of different kinds of materials. A binder can be added, and that binder can be either a nonconducting or a conducting binder. Nonconducting binders can be, for example, a polymer or a glass. A conducting binder enables the device to be both proton conducting and electron conducting. The solid acid material has the general form M.sub.a H.sub.b (XO.sub.t).sub.c.

Chisholm, Calum↗

Proton conducting membrane using a solid acid

A solid acid material is used as a proton conducting membrane in an electrochemical device. The solid acid material can be one of a plurality of different kinds of materials. A binder can be added, and that binder can be either a nonconducting or a conducting binder. Nonconducting binders can be, for example, a polymer or a glass. A conducting binder enables the device to be both proton conducting and electron conducting.

Haile, Sossina M.↗