Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ThIN”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Microstructural evaluation of thin-wall sections of 316L stainless steel produced by laser powder-bed fusion processing

Laser powder bed fusion (LBPF) is a method of additive manufacturing (AM) that offers a means to fabricate complex components with features which rely upon the mechanical integrity of thin-wall (less than 0.4 mm thick) structures. The microstructure of a 316L AM thin wall is investigated as metallographically prepared from a cylindrical shell. Optimization is pursued through mechanical polishing and chemical etching to minimize the effects of surface roughness. Microanalysis measurements of the sectioned component reveal the sample has high microstructural fidelity, uniform composition and phase content across grain as well as powder layer boundaries within the thin wall. The results are attributed to a uniform thermal gradient at the part scale during rapid solidification.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Impact of Annealing on the Chemical and Superconducting Properties of Ta Thin Films

Tantalum thin films are annealed to dissolve the surface oxide. The effect of annealing is studied using material characterization tools, XPS and TOF-SIMS, and electrical transport measurements of the annealed films are taken using standard PPMS methods to correlate with the surface chemistry. Annealing dissociates the surface oxide, and the oxygen produced diffuses into the thin film. The introduction of oxygen reduces the quality of the thin film, as shown by the suppression of Tc and a reduction in RRR.

Shinde, Maithilee [IIT, Chicago]↗
DOE OSTI2024

ZnO-Au Hybrid Metamaterial Thin Films with Tunable Optical Properties

ZnO-Au nanocomposite thin films have been previously reported as hybrid metamaterials with unique optical properties such as plasmonic resonance properties and hyperbolic behaviors. In this study, Au composition in the ZnO-Au nanocomposites has been effectively tuned by target composition variation and thus resulted in microstructure and optical property tuning. Specifically, all the ZnO-Au nanocomposite thin films grown through the pulsed laser deposition (PLD) method show obvious vertically aligned nanocomposite (VAN) structure with the Au nanopillars embedded in the ZnO matrix. Moreover, the average diameter of Au nanopillars increases as Au concentration increases, which also leads to the redshifts in the surface plasmon resonance (SPR) wavelength and changes in the hyperbolic behaviors of the films. As a whole, this work discusses how strain-driven tuning of optical properties and microstructure resulted through a novel Au concentration variation approach which has not been previously attempted in the ZnO-Au thin film system. These highly ordered films present great promise in the areas of sensing, waveguides, and nanophotonics to name a few.

Bhatt, Nirali A.↗
DOE OSTI2022

Implementation of Sacrificial Support Structures for Hybrid Manufacturing of Thin Walls

Thin-walled features can be difficult to produce with traditional machining methods which often rely on excess stock material for stiffness. This challenge is increased in hybrid manufacturing where the feature is already near net shape before machining. Significant workpiece deflection can result in poor geometric and surface finish tolerances on the finished part. A potential solution to this problem is to implement sacrificial support structures to the as-printed geometry. The supports are then machined away during the finishing portion of the hybrid process. In the present work, several different design parameters for these sacrificial supports were evaluated to determine their impact on the quality of representative thin wall geometry samples. The angle, height, and spacing of triangular support structures were varied for each sample and then machined and examined. The addition of these supports relative to an unsupported configuration provided a deflection reduction of around 0.2 mm. Surface roughness was improved by approximately 1.5 µm. Increasing values of support height were found to correspond to reduced wall deflection. Similarly, decreasing values of support angle and support spacing improved geometric accuracy. Efficiency comparisons showed that increases in print time corresponded to rapidly diminishing gains in geometric accuracy but continued to improve surface roughness. Implications for hybrid finishing of additively manufactured thin-walled structures is briefly discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Compositionally-Driven Formation Mechanism of Hierarchical Morphologies in Co-Deposited Immiscible Alloy Thin Films

Co-deposited, immiscible alloy systems form hierarchical microstructures under specific deposition conditions that accentuate the difference in constituent element mobility. The mechanism leading to the formation of these unique hierarchical morphologies during the deposition process is difficult to identify, since the characterization of these microstructures is typically carried out post-deposition. We employ phase-field modeling to study the evolution of microstructures during deposition combined with microscopy characterization of experimentally deposited thin films to reveal the origin of the formation mechanism of hierarchical morphologies in co-deposited, immiscible alloy thin films. Our results trace this back to the significant influence of a local compositional driving force that occurs near the surface of the growing thin film. We show that local variations in the concentration of the vapor phase near the surface, resulting in nuclei (i.e., a cluster of atoms) on the film’s surface with an inhomogeneous composition, can trigger the simultaneous evolution of multiple concentration modulations across multiple length scales, leading to hierarchical morphologies. We show that locally, the concentration must be above a certain threshold value in order to generate distinct hierarchical morphologies in a single domain.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of Intermediate Semiconducting TiOx Thin Films on Nanoparticle-Mediated Electron Transfer: Electrooxidation of CO

The concept of nanoparticle-mediated electron transfer (eT) across insulating thin films was elucidated theoretically by Allongue and Chazalviel in 2011. In their model, metal nanoparticles (NPs) are immobilized atop passivating, self-assembled monolayers (SAMs). They found that under certain conditions, related to the thickness of the SAM and the size of the NPs, efficient faradaic oxidation and reduction reactions could proceed at the NP surface. In the absence of NPs, however, eT was suppressed by the insulating SAM thin films. Allongue and Chazalviel concluded that, within certain bounds, eT is mediated by fast tunneling between the conductive electrode and the metal NPs, while the kinetics of the redox reaction are controlled by the NPs. This understanding has been confirmed using a variety of experimental models. The theory is based on electron tunneling; therefore, the nature of the intervening medium (the insulator in prior studies) should not affect the eT rate. In the present manuscript, however, we show that the theory breaks down under certain electrochemical conditions when the medium between conductors is an n-type semiconductor. Specifically, we find that in the presence of either Au or Pt NPs immobilized on a thin film of TiOx, CO electrooxidation does not proceed. In contrast, the exact same systems lead to the efficient reduction of oxygen. At present, we are unable to explain this finding within the context of the model of Allongue and Chazalviel.

Galyamova, Aigerim↗
DOE OSTI2024

Heterogeneous Morphologies and Hardness of Co-Sputtered Thin Films of Concentrated Cu-Mo-W Alloys

Heterogeneous microstructures in Cu-Mo-W alloy thin films formed by magnetron co-sputtering immiscible elements with concentrated compositions are characterized using scanning transmission electron microscopy (STEM) and nanoindentation. In this work, we modified the phase separated structure of a Cu-Mo immiscible system by adding W, which impedes surface diffusion during film growth. The heterogeneous microstructures in the Cu-Mo-W ternary system exhibited bicontinuous matrices and agglomerates composed of Mo(W)-rich phase. This is unique, as these are the slower-diffusing species, contrasting past reports of binary Cu-Mo thin films that exhibited Cu-rich agglomerates. The bicontinuous matrices comprised of Cu-rich and Mo(W)-rich phases exhibited bilayer thicknesses of less than 5 nm. The hardness of these thin films measured using nanoindentation is reported and compared to similar multilayers and nanocomposites in binary systems.

36 MATERIALS SCIENCE↗
NASA NTRS1971

Study of structural behavior of thin films

The work directed towards developing methods of increasing the strength of thin boron films is reported. The program was divided into two main parts. The first involved the improvement of methods for the measurement of the strength of thin films. The second was a study of the effect of condensation of deposition temperature on the strength of the films. Techniques were developed for depositing boron films onto both sides of thin titanium and tantalum foils. Small dogbone sections of boron were made by masking. Strain gauges were then mounted on these to measure failure strains when the films were loaded in tension. Test results were consistent with those obtained by flexure tests. The most important flaws in the boron films appeared to have been generated by either small globules of boron ejected from the melt or small particles (possibly boron dust) on the substrate prior to deposition.

Feakes, F.↗
NASA NTRS1972

Excitation of Love waves in a thin film layer by a line source.

The excitation of a Love surface wave guided by a thin film layer deposited on a semiinfinite substrate is studied in this paper. Both the thin film and the substrate are considered to be elastically isotropic. Amplitudes of the surface wave in the thin film region and the substrate are found in terms of the strength of a line source vibrating in a direction transverse to the propagating wave. In addition to the surface wave, the bulk shear wave excited by the source is also studied. Analytical expressions for the bulk wave amplitude as a function of the direction of propagation, the acoustic powers transported by the surface and bulk waves, and the efficiency of surface wave excitation are obtained. A numerical example is given to show how the bulk wave radiation pattern depends upon the source frequency, the film thickness and other important parameters of the problem. The efficiency of surface wave excitation is also calculated for various parameter values.

Tuan, H.-S.↗
NASA NTRS1972

Infrared radiation of thin plastic films.

A combined analytical and experimental study is presented for infrared radiation characteristics of thin plastic films with and without a metal substrate. On the basis of the thin-film analysis, a simple analytical technique is developed for determining band-averaged optical constants of thin plastic films from spectral normal transmittance data for two different film thicknesses. Specifically, the band-averaged optical constants of polyethylene terephthalate and polyimide were obtained from transmittance measurements of films with thicknesses in the range of 0.25 to 3 mil. The spectral normal reflectance and total normal emittance of the film side of singly aluminized films are calculated by use of optical constants; the results compare favorably with measured values.

Tien, C. L.↗
NASA NTRS1973

Application of the hydrogen-bubble technique for velocity measurements in thin liquid films.

A unique adaptation of the hydrogen-bubble flow visualization method was applied to measure velocity profiles and film thicknesses of very thin films on an inclined plane wall. Data were obtained in the three flow regions for a developing falling film with an initially uniform velocity profile and thickness less than or equal to 0.1 in. The measured profiles compared more favorably with parabolic profiles in the intermediate fully developed region than in the initial developing region. However, measured film thicknesses compared favorably with a simplified solution of the integral momentum equation based on parabolic velocity profiles. The results confirm the theoretical prediction that a relatively long distance may be required even for a thin film before nonaccelerating flow with a constant film thickness is obtained and Nusselt's classical analysis applies. The experimental technique was shown to be a practical experimental method for obtaining data for the two-dimensional laminar flow of thin liquid films.

Thomas, W. C.↗
NASA NTRS1974

Potential of thin, sputtered films as erosion resistant protective coatings, part 1

The characteristics of thin, pyrolytically deposited films for protection of surfaces from oxidation and abrasion are discussed. The limitations of depositing erosion resistant films are described. Environmental tests of first stage compressor blades in a T-58 engine after coating with a thin film were conducted. Photographic examples of the effectiveness of the thin films in protecting the turbine blades are provided. Methods for operating a sputtering system and the equipment used for film deposition are defined.

Gentner, K.↗
NASA NTRS1972

Thin-film diffusion brazing of titanium alloys

A thin film diffusion brazing technique for joining titanium alloys by use of a Cu intermediate is described. The method has been characterized in terms of static and dynamic mechanical properties on Ti-6Al-4V alloy. These include tensile, fracture toughness, stress corrosion, shear, corrosion fatigue, mechanical fatigue and acoustic fatigue. Most of the properties of titanium joints formed by thin film diffusion brazing are equal or exceed base metal properties. The advantages of thin film diffusion brazing over solid state diffusion bonding and brazing with conventional braze alloys are discussed. The producibility advantages of this process over others provide the potential for producing high efficiency joints in structural components of titanium alloys for the minimum cost.

Mikus, E. B.↗
NASA NTRS1974

Method of fabricating an object with a thin wall having a precisely shaped slit

A method is described for making a structure with a cavity and a thin wall with a precisely shaped slit. An object with a cavity having two openings, one of which is to be closed by a thin wall with a slit, is placed on the surface of a fixture. The fixture surface has a slot conforming to the size and shape of the slit to be formed in the thin wall.

Christopher, P. A.↗
NASA NTRS1975

Investigation of the difficulties associated with the use of lead telluride and other II - IV compounds for thin film thermistors

The fabrication of thermistors was investigated for use as atmospheric temperature sensors in meteorological rocket soundings. The final configuration of the thin film thermistor is shown. The composition and primary functions of the six layers of the sensor are described. A digital controller for thin film deposition control is described which is capable of better than .1 A/sec rate control. The computer program modules for digital control of thin film deposition processing are included.

Mclennan, W. D.↗
NASA NTRS1976

Leading-edge singularities in thin-airfoil theory

If the thin airfoil theory is applied to an airfoil having a rounded leading edge, a certain error will arise in the determination of the pressure distribution around the nose. It is shown that the evaluation of the drag of such a blunt nosed airfoil by the thin airfoil theory requires the addition of a leading edge force, analogous to the leading edge thrust of the lifting airfoil. The method of calculation is illustrated by application to: (1) The Joukowski airfoil in subsonic flow; and (2) the thin elliptic cone in supersonic flow. A general formula for the edge force is provided which is applicable to a variety of wing forms.

Jones, R. T.↗
NASA NTRS1976

Finite element representations for thin shell instability analysis

The development of finite element calculational procedures for thin-shell instability analysis has involved the definition of appropriate element representations (i.e. the geometric form of the element and the approximation of displacement and/or stress), constitutive expressions, and computational algorithms. Among these, the status of thin-shell finite element representations remains unsettled. This paper, therefore, emphasizes recent developments in the basic aspects of thin-shell finite element analysis and discusses one simplified approach in more detail. Formulative and computational procedures for elastic instability analysis are then summarized, and numerical results are shown for the simplified shell element formulation.

Gallagher, R. H.↗
NASA NTRS1977

Polyimide thin-film dielectrics on ferroelectrics

Conducting layers of multi-layered thin-film ferroelectric device, such as is used in liquid crystal/ferroelectric display, can be electrically isolated using thin-film layer of polyimide. Ease of application and high electrical-breakdown strength allow dependable and economical means of providing dielectric for other thin-film microelectronic devices.

Galiardi, R. V.↗