Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “THERMAL FRACTURES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

Thermal drawdown and late‐stage seismic‐slip fault reactivation in enhanced geothermal reservoirs

Abstract Late‐stage seismic slip in geothermal reservoirs has been shown as a potential mechanism for inducing seismic events of magnitudes to ~2.6 as late as two decades into production. We investigate the propagation of fluid pressures and thermal stresses in a prototypical geothermal reservoir containing a centrally located critically stressed fault from a doublet injector and withdrawal well to define the likelihood, timing, and magnitude of events triggered by both fluid pressures and thermal stresses. We define two bounding modes of fluid production from the reservoir. For injection at a given temperature, these bounding modes relate to either low‐ or high‐relative flow rates. At low relative dimensionless flow rates the pressure pulse travels slowly, the pressure‐driven changes in effective stress are muted, but thermal drawdown propagates through the reservoir as a distinct front. This results in the lowest likelihood of pressure‐triggered events but the largest likelihood of late‐stage thermally triggered events. Conversely, at high relative non‐dimensional flow rates the propagating pressure pulse is larger and migrates more quickly through the reservoir but the thermal drawdown is uniform across the reservoir and without the presence of a distinct thermal front, and less capable of triggering late‐stage seismicity. We evaluate the uniformity of thermal drawdown as a function of a dimensionless flow rate Q D that scales with fracture spacing s ( m ), injection rate q ( kg/s ), and the distance between the injector and the target point L ∗ ( Q D ∝ qs 2 / L ∗ ). This parameter enables the reservoir characteristics to be connected with the thermal drawdown response around the fault and from that the corresponding magnitude and timing of seismicity to be determined. These results illustrate that the dimensionless temperature gradient adjacent to the fault dT D / dx D is exclusively controlled by the factor Q D . More significantly, this temperature gradient correlates directly with both the likelihood and severity of triggered events, enabling the direct scaling of likely magnitudes and timing to be determined a priori and directly related to the characteristics of the reservoir. This dimensionless scaling facilitates design for an optimum Q D value to yield both significant heat recovery and longevity of geothermal reservoirs while minimizing associated induced seismicity.

Gan, Quan↗

Computational Analysis of Coupled Geoscience Processes in Fractured and Deformable Media

Prediction of flow, transport, and deformation in fractured and porous media is critical to improving our scientific understanding of coupled thermal-hydrological-mechanical processes related to subsurface energy storage and recovery, nonproliferation, and nuclear waste storage. Especially, earth rock response to changes in pressure and stress has remained a critically challenging task. In this work, we advance computational capabilities for coupled processes in fractured and porous media using Sandia Sierra Multiphysics software through verification and validation problems such as poro-elasticity, elasto-plasticity and thermo-poroelasticity. We apply Sierra software for geologic carbon storage, fluid injection/extraction, and enhanced geothermal systems. We also significantly improve machine learning approaches through latent space and self-supervised learning. Additionally, we develop new experimental technique for evaluating dynamics of compacted soils at an intermediate scale. Overall, this project will enable us to systematically measure and control the earth system response to changes in stress and pressure due to subsurface energy activities.

58 GEOSCIENCES↗

Monitoring Eruptive Activity at Mount St. Helens with TIR Image Data

Thermal infrared (TIR) data from the MASTER airborne imaging spectrometer were acquired over Mount St. Helens in Sept and Oct, 2004, before and after the onset of recent eruptive activity. Pre-eruption data showed no measurable increase in surface temperatures before the first phreatic eruption on Oct 1. MASTER data acquired during the initial eruptive episode on Oct 14 showed maximum temperatures of similar to approximately 330 C and TIR data acquired concurrently from a Forward Looking Infrared (FLIR) camera showed maximum temperatures similar to approximately 675 C, in narrow (approximately 1-m) fractures of molten rock on a new resurgent dome. MASTER and FLIR thermal flux calculations indicated a radiative cooling rate of approximately 714 J/m(exp 2)/s over the new dome, corresponding to a radiant power of approximately 24 MW. MASTER data indicated the new dome was dacitic in composition, and digital elevation data derived from LIDAR acquired concurrently with MASTER showed that the dome growth correlated with the areas of elevated temperatures. Low SO2 concentrations in the plume combined with sub-optimal viewing conditions prohibited quantitative measurement of plume SO2. The results demonstrate that airborne TIR data can provide information on the temperature of both the surface and plume and the composition of new lava during eruptive episodes. Given sufficient resources, the airborne instrumentation could be deployed rapidly to a newly-awakening volcano and provide a means for remote volcano monitoring.

thermal emissions↗

Derivation of the New Pressurized Thermal Shock Screening Criteria

As a result of a multi-year, multi-disciplinary effort on the part of the United States Nuclear Regulatory Commission (USNRC), its contractors, and the nuclear industry, a technical basis has been established to support a risk-informed revision to pressurized thermal shock (PTS) regulations originally promulgated in the mid-1980s. The revised regulations provide alternative (optional) reference-temperature (RT)-based screening criteria, which is codified in 10 CFR 50.61(a). How the revised screening criteria were determined from the results of the probabilistic fracture mechanics (PFM) analyses will be discussed in this paper.

99 GENERAL AND MISCELLANEOUS↗

Durable aluminate toughened zirconate composite thermal barrier coating (TBC) materials for high temperature operation

Research on advanced thermal barrier coating (TBC) materials capable of operating beyond 1200°C has primarily focused on the rare earth zirconate pyrochlores, particularly gadolinium zirconate (Gd 2 Zr 2 O 7 – GZO). The drawback of this material is a significant reduction in durability due to a low fracture toughness. This study investigates utilization of a thermodynamically compatible gadolinia alumina perovskite (GdAlO 3 – GAP) toughening phase to improve the durability of GZO. Dense pellets were fabricated to assess the material properties with minimal microstructural influence. Thermal stability, elastic modulus, hardness, indentation fracture resistance and erosion durability were evaluated for GZO, GAP, and composite pellets containing 10, 30, and 50 wt.% GAP. It was demonstrated that GAP and GZO are thermodynamically compatible through 1600°C and thus capable of operating well beyond the limits of traditional 7 wt.% yttria stabilized zirconia (YSZ). Grain sizes are maintained due to a lack of diffusion, and thus microstructural stability is enhanced. The GAP fracture toughness was shown to be over 2X that of GZO while exhibiting a lower elastic modulus and similar hardness. The 50:50 GZO-GAP composite exhibited a 63% reduction in the absolute erosion rate, demonstrating the immense toughening capabilities of this system. The implications for composite TBCs utilizing this system are discussed, along with future research.

36 MATERIALS SCIENCE↗

Effect of thermal profile on cyclic flaw growth in aluminum

Surface flawed and single edge notch tension specimens of 2219-T851 and -T87 aluminum were tested to determine static fracture characteristics and base line (constant amplitude, constant temperature) cyclic flaw growth behavior. Subsequent testing was then conducted in which flawed specimens were subjected to a thermal profile in which the applied stress was varied simultaneously with the temperature. The profile used represents a simplified space shuttle orbiter load/temperature flight cycle. Test temperatures included the range from 144K (-200 F) up to 450K (350 F). The measured flaw growth rates obtained from the thermal profile tests were then compared with rates predicted by assuming linear cumulative damage of base line rates.

Engstrom, W. L.↗

Mechanical Properties and Corrosion Behavior of As-Cast Mg-Zn-Zr-(La) Magnesium Alloys

The effects of La content on the mechanical properties and corrosion behavior of as-cast Mg-Zn-Zr (ZK) magnesium alloys were investigated. The results showed that La addition to ZK60 alloy resulted in a considerable grain refinement and an increase in the volume fraction of second phases by formation of Mg-Zn-La ternary phase. The tensile tests were performed at both room and elevated temperatures. At room temperature, the yield and tensile strengths and elongation-to-fracture significantly increased with 0.2 wt.% La addition, then deteriorated slightly with increasing La additions above 0.2 wt.%. At 200 °C, the yield and tensile strengths continually improved and elongation-to-fracture decreased with increasing La content due to the presence of thermally stable Mg-Zn-La phase. Immersion and electrochemical corrosion tests revealed that the formation of Mg-Zn-La phases led to a higher amount of cathodic sites and preferential corrosion propagation, and thus a decrease in the corrosion resistance of ZK60 alloys.

36 MATERIALS SCIENCE↗

FY20 Verification of BISON Using Analytic and Manufactured Solutions

In 2010, the U.S. Department of Energy created its first Energy Innovation Hub, which is focused on developing high-fidelity and high-resolution Modeling and Simulation (M&S) tools for modeling of Light Water Reactors (LWRs). This hub, Consortium for Advanced Simulation of LWRs (CASL), has developed an LWR simulation tool called Virtual Environment for Reactor Applications (VERA). The multi-physics capability of VERA is achieved through the coupling of single-physics codes, including BISON, CTF, MPACT, and MAMBA. BISON is a fuel performance code which models the thermo-mechanical behavior of nuclear fuel using high performance M&S. It is capable of modeling traditional LWR fuel rods, fuel plates, and TRi-structural ISOtropic (TRISO) fuel particles. It can employ three-dimensional Cartesian, two-dimensional axisymmetric cylindrical, or one-dimensional radial spherical geometry. It includes empirical models for a large variety of fuel physics: temperature- and burnup-dependent thermal properties, fuel swelling and densification, fission gas production, cladding creep, fracture, cladding plasticity, and gap/plenum models. This document details a series of code verification test problems that are used to test BISON. These problems add confidence that the BISON code is a faithful representation of its underlying mathematical model. The suite of verification tests are mapped to the underlying conservation equations solved by the code: heat conduction, mechanics, and species conservation. Twenty-two problems are added for the heat conduction solution, two for the mechanics solution, and none for species conservation. Method of Manufactured Solutions (MMS) capability is demonstrated with three problems, and temperature drops across the fuel gap are tested.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Microfissuring of Inconel 718

A tentative mathematical computer model of the microfissuring process during electron beam welding of Inconel 718 has been constructed. Predictions of the model are compatible with microfissuring tests on eight 0.25-in. thick test plates. The model takes into account weld power and speed, weld loss (efficiency), parameters and material characteristics. Besides the usual material characteristics (thermal and strength properties), a temperature and grain size dependent critical fracture strain is required by the model. The model is based upon fundamental physical theory (i.e., it is not a mere data interpolation system), and can be extended to other metals by suitable parameter changes.

Nunes, A. C., Jr.↗

Interpenetrating polymer network approach to tougher and more microcracking resistant high temperature polymers. I - LaRC-RP40

Interpenetrating polymer networks in the form of the LaRC-RP40 resin, prepared by the in situ polymerization of a thermosetting imide prepolymer and thermoplastic monomer reactants, are presently used to obtain toughness and microcracking resistance in a high-temperature polymer. Attention is presently given to the processing, physical, and mechanical properties, as well as the thermooxidative stability, of both the neat resin and the resin as a graphite fiber-reinforced matrix. Microcracking after thermal cycling was also tested. LaRC-RP40 exhibits significant resin fracture toughness improvements over the PMR-15 high-temperature matrix resin.

Pater, Ruth H.↗

Flexural ridges, trenches, and outer rises around coronae on Venus

Flexural signatures outboard of Venusian coronal rims are examined with the purpose of inferring the thickness of the planet's elastic lithosphere. Topographic profiles of several prominent coronae which display clear trench and outer rise signatures are presented. Via a thin elastic plate flexure model to characterize the shape of the trench and outer rise, Venusian flexures are found to be similar in both amplitude and wavelength to lithospheric flexures seaward of subduction zones on earth. It is shown that circumferential fractures are concentrated in areas where the topography is curved downward, in good agreement with the high tensile stress predicted by the flexure models. Two scenarios for the development of the ridge-trench-outer rise flexural topography and circumferential fractures of coronae are presented. The first scenario involves reheating and thermal subsidence of the lithosphere interior to the corona, while the second involves expansion of the corona interior and roll back of the subducting lithosphere exterior to the corona.

Sandwell, David T.↗

Strong, Tough, and Pest Resistant MoSi2-Base Hybrid Composite for Structural Applications

Addition of about 30 to 50 vol % of Si3N4 particulate to MoSi2 improved resistance to low temperature accelerated oxidation by forming a Si2ON2 protective scale and thereby eliminating catastrophic 'pest failure'. The Si3N4 addition also improved the high temperature creep strength by nearly five orders of magnitude, doubled the room temperature toughness and significantly lowered the CTE of the MoSi2 and eliminated matrix cracking in SCS-6 reinforced composites even after thermal cycling. The SCS-6 fiber reinforcement improved the room temperature fracture toughness by seven times and impact resistance by five times. The composite exhibited excellent strength and toughness improvement up to 1400 C. More recently, tape casting was adopted as the preferred processing of MoSi2-base composites for improved fiber spacing, ability to use small diameter fibers, and for lower cost. Good strength and toughness values were also obtained with fine diameter Hi-Nicalon tow fibers. This hybrid composite remains competitive with ceramic matrix composites as a replacement for Ni-base superalloys in aircraft engine applications.

Hebsur, M. G.↗

Development and Characterization of SiC)/ MoSi2-Si3N4(p) Hybrid Composites

Intermetallic compound MoSi2 has long been known as a high temperature material that has excellent oxidation resistance and electrical/thermal conductivity. Also its low cost, high melting point (2023 C), relatively low density (6.2 g/cu cm versus 9 g/cu cm for current engine materials), and ease of machining, make it an attractive structural material. However, the use of MoSi2 has been hindered due to its poor toughness at low temperatures, poor creep resistance at high temperatures, and accelerated oxidation (also known as 'pest' oxidation) at temperatures between approximately 450 and 550 C. Continuous fiber reinforcing is very effective means of improving both toughness and strength. Unfortunately, MoSi2 has a relatively high coefficient of thermal expansion (CTE) compared to potential reinforcing fibers such as SiC. The large CTE mismatch between the fiber and the matrix resulted in severe matrix cracking during thermal cycling. Addition of about 30 to 50 vol % of Si3N4 particulate to MoSi2 improved resistance to low temperature accelerated oxidation by forming a Si2ON2 protective scale and thereby eliminating catastrophic 'pest failure'. The Si3N4 addition also improved the high temperature creep strength by nearly five orders of magnitude, doubled the room temperature toughness and significantly lowered the CTE of the MoSi2 and eliminated matrix cracking in SCS-6 reinforced composites even after thermal cycling. The SCS-6 fiber reinforcement improved the room temperature fracture toughness by seven times and impact resistance by five times. The composite exhibited excellent strength and toughness improvement up to 1400 C. More recently, tape casting was adopted as the preferred processing of MoSi2-base composites for improved fiber spacing, ability to use small diameter fibers, and for lower cost. Good strength and toughness values were also obtained with fine diameter Hi-Nicalon tow fibers. This hybrid composite remains competitive with ceramic matrix composites as a replacement for Ni-base superalloys in aircraft engine applications.

Hebsur, Mohan G.↗

MoSi2-Base Hybrid Composites from Aeroengine Applications

Addition of about 30 to 50 vol % of Si3N4 particulate to MoSi2 improved low temperature accelerated oxidation resistance by forming a Si2ON2 protective scale and thereby eliminated catastrophic 'pest failure'. The Si3N4 addition also improved the high temperature creep strength by nearly five orders of magnitude, doubled the room temperature toughness, and significantly lowered the CTE of the MoSi2 which eliminated matrix cracking in SCS-6 reinforced composites even after thermal cycling. The SCS-6 fiber reinforcement improved the room temperature fracture toughness by seven times and impact resistance by five times. The composite exhibited this excellent strength and toughness improvement up to 1673 K. More recently, tape casting was adopted as the preferred processing of MoSi2-base composites due to improved fiber spacing, ability to use small diameter fibers, and for lower cost. Good strength and toughness values were also obtained with fine diameter Hi-Nicalon tow fibers. These hybrid composites remain competitive with ceramic matrix composites as a replacement for Ni-base superalloys in aircraft engine applications.

Hebsur, Mohan G.↗

Macro-scale Testing and Micromechanics Modeling of Fracture Behaviors for Boron Carbide Composites with Hierarchical Microstructures

With a unique combination of properties including high hardness, low density, wear and corrosion resistance, thermal stability, high neutron absorption, and semi-conductivity, boron carbide (B4C) is a candidate material for various engineering applications that involve extreme environment. The current applications of boron carbide, however, are limited by its intrinsic brittleness due to its strong covalent bonding. To toughen boron carbide, in this work hierarchical microstructure designs was used to provide multiple toughening mechanisms including crack deflection/bridging, micro-crack toughening, etc. Using field assisted sintering, B4C composites with hierarchical microstructure features including graphite platelets, micron and sub-micron sized TiB2 reinforcements were fabricated. The fracture toughness of fabricated B4C composites were previously measured at micro-scale using micro-indentation followed by post-testing microstructure inspection. However, questions including whether the fracture toughness enhancement measured at micro-scale can translate to macro-scale mechanical properties, and what are the fundamental mechanisms behind observed fracture toughness enhancement, remain to be answered. In this study, the fabricated B4C composites were tested using standardized four-point bending method to obtain fracture toughness at macro-scale. In addition, micromechanics modeling was conducted using MAC/GMC code and crack-band model to study the effect of residual stress and weak interphases on fracture behaviors of B4C composites reinforced with TiB2 particles. Through standardized four-point bending tests, fracture toughness enhancements up to 2.85, 3.32, and 3.65 MPa∙m(exp 1/2) (from 2.38 MPa∙m(exp 1/2)) were achieved for B4C composites with graphite platelets addition (micro/nano B4C), with TiB2 formation (micro B4C-TiB2), and with both graphite and TiB2 addition (micro/nano B4C-TiB2) respectively. Micromechanics modeling indicated that introduction of thermal residual stress and weak interphases caused enhanced micro-cracking behavior and resulted in the observed fracture toughness enhancement. These results furthered understanding about the mechanical behaviors at macro-scale and the mechanisms behind observed fracture toughness enhancement for B4C composites with hierarchical microstructures and can provide reference data for the future design of B4C composites with optimized microstructures for further fracture toughness enhancement.

Boron Carbide↗

LLNL 5-2428: Fracture Permeability and Seismic Slip Behavior

Our goal is to develop, apply and validate a holistic thermal, hydrologic, mechanical, and chemical (THMC) workflow that also includes evaluation of induced seismic slip in EGS reservoirs. We will integrate experimental and modelling approaches to reduce parameteruncertainty and better predict and mitigate seismic hazard at Utah FORGE and future EGS sites.We propose a novel approach that incorporates 3D physics-based Earthquake simulations in THMC models, herein referred to as “THMC+E” models. This capability will enable improvedengineering decisions at Utah FORGE and move EGS operations toward repeatable, robust, economically viable, and socially accepted development. Utah FORGE management and future EGS operators may employ results of THMC+E models for decision making purposes throughout the lifetime of the field operation. For example, before production well installation, our THMC+E models will predict circulation scenarios and related seismic hazard for a suite ofpossible well locations and flow rates, thus enabling evaluation of optimal production well placement. Such efforts will be conducted throughout the lifetime of the project, whereby additional laboratory experiments will constrain key model parameters and machine learning (ML) will reduce the size of the parameter space and the associated uncertainty. THMC+E simulations will enable exploration various circumstances that may hinder EGS success and develop mitigation strategies.

58 GEOSCIENCES↗

Simulating Dynamic Fracture in Oxide Fuel Pellets Using Cohesive Zone Models

It is well known that oxide fuels crack during the first rise to power, with continued fracture occurring during steady operation and especially during power ramps or accidental transients. Fractures have a very strong influence on the stress state in the fuel which, in turn, drives critical phenomena such as fission gas release, fuel creep, and eventual fuel/clad mechanical interaction. Recently, interest has been expressed in discrete fracture methods, such as the cohesive zone approach. Such models are attractive from a mechanistic and physical standpoint, since they reflect the localized nature of cracking. The precise locations where fractures initiate, as well as the crack evolution characteristics, are determined as part of the solution. This paper explores the use of finite element cohesive zone concepts to predict dynamic crack behavior in oxide fuel pellets during power-up, steady operation, and power ramping. The aim of this work is first to provide an assessment of cohesive zone models for application to fuel cracking and explore important numerical issues associated with this fracture approach. A further objective is to provide basic insight into where and when cracks form, how they interact, and how cracking effects the stress field in a fuel pellet. The ABAQUS commercial finite element code, which includes powerful cohesive zone capabilities, was used for this study. Fully-coupled thermo-mechanical behavior is employed, including the effects of thermal expansion, swelling due to solid and gaseous fission products, and thermal creep. Crack initiation is determined by a temperature-dependent maximum stress criterion, based on measured fracture strengths for UO2. Damage evolution is governed by a traction-separation relation, calibrated to data from temperature and burn-up dependent fracture toughness measurements. Numerical models are first developed in 2D based on both axisymmetric (to explore axial cracking) and plane strain (to explore radial cracking) assumptions. A 3D model is then developed, permitting simultaneous radial and axial fractures. Although fuel cracking is clearly three-dimensional, 2D models are of interest since they are simpler to implement, are much less computationally intensive, and have potential application to existing 2D fuel performance codes. Numerical issues related to cohesive zone models, such as mesh dependency and viscous stabilization, are addressed. Model results indicate that for typical oxide fuel properties, both axial and radial cracking occurs during initial heat-up, well before steady-state thermal gradients are established in the pellet. Cracking results in local stress relief and a shift in peak stress locations, leading to the initiation of new cracks. Continued growth of existing cracks, plus the initiation and growth of additional fractures, is observed during steady operation and power ramping. 3D models provide considerable insight into the progressive interactions between radial and axial cracking. Parametric studies demonstrate the effects of temperature dependent material properties on crack initiation and progression. Increasing fracture strength and toughness with temperature, leads to crack arrest in high temperature regions near the pellet’s symmetry axis.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Hydraulic Response to Thermal Stimulation Efforts at Raft River Based on Stepped Rate Injection Testing

The injection well stimulation project at the Raft River geothermal field tests the effect of long-term cold water injection and high pressure injection on well injectivity, improvements to which could reduce operating costs. The primary data for analysis and interpretation of the injection test are step-rate flow tests run before each new phase of the injection. These tests were analyzed using a combination of standard pump-test analytical solution methods and methods developed expressly for the observed conditions. The stepped rate injection tests, combined with long-term flow and pressure response data suggest that the well is located within a fractured formation of low transmissivity but high storativity. These calculated parameters appeared to increase with pressure during the first injection test and the higher values were reproduced during the second stepped rate test. Calculated transmissivity and storativity are on the order of 4E-5 m cm 2 and 1E-4 m Pa -1 , respectively. The apparent pressure dependence of fitted hydraulic parameters may reflect near-well fracture compliance that increased the effective radius of the wellbore during the first test. While the type curve fit analysis also suggests that the reservoir behaves as a uniformly fractured reservoir with a radial flow regime, the hydraulic parameters indicate that condition may exist only a very limited distance (<10 m) from the well. Longer-term pressure response suggests that flow in the system effectively reaches steady state in a period of less than a day, which may reflect pressure stabilization resulting from pressure-dependent permeability or a region of much higher permeability located with a few meters of the well. The transmissivity estimates obtained from this analysis, converted to approximate fracture density and aperture, provide useful constraints on the distance to which the thermal front may migrate from the well during the cold water injection phase of the stimulation project. We estimate that the cooling front will migrate less than a tenth of a kilometer over an approximately one-year injection period. Here, the effects of that cooling, however, may be substantial, because increases in permeability have maximum effect nearest the well.

cold water injection↗