Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Stators”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
NASA NTRS2003

Flux-Based Deadbeat Control of Induction-Motor Torque

An improved method and prior methods of deadbeat direct torque control involve the use of pulse-width modulation (PWM) of applied voltages. The prior methods are based on the use of stator flux and stator current as state variables, leading to mathematical solutions of control equations in forms that do not lend themselves to clear visualization of solution spaces. In contrast, the use of rotor and stator fluxes as the state variables in the present improved method lends itself to graphical representations that aid in understanding possible solutions under various operating conditions. In addition, the present improved method incorporates the superposition of high-frequency carrier signals for use in a motor-self-sensing technique for estimating the rotor shaft angle at any speed (including low or even zero speed) without need for additional shaft-angle-measuring sensors.

Kenny, Barbara H.↗
NASA NTRS2013

Effect of Two Advanced Noise Reduction Technologies on the Aerodynamic Performance of an Ultra High Bypass Ratio Fan

A wind tunnel experiment was conducted in the NASA Glenn Research Center anechoic 9- by 15-Foot Low-Speed Wind Tunnel to investigate two new advanced noise reduction technologies in support of the NASA Fundamental Aeronautics Program Subsonic Fixed Wing Project. The goal of the experiment was to demonstrate the noise reduction potential and effect on fan model performance of the two noise reduction technologies in a scale model Ultra-High Bypass turbofan at simulated takeoff and approach aircraft flight speeds. The two novel noise reduction technologies are called Over-the-Rotor acoustic treatment and Soft Vanes. Both technologies were aimed at modifying the local noise source mechanisms of the fan tip vortex/fan case interaction and the rotor wake-stator interaction. For the Over-the-Rotor acoustic treatment, two noise reduction configurations were investigated. The results showed that the two noise reduction technologies, Over-the-Rotor and Soft Vanes, were able to reduce the noise level of the fan model, but the Over-the-Rotor configurations had a significant negative impact on the fan aerodynamic performance; the loss in fan aerodynamic efficiency was between 2.75 to 8.75 percent, depending on configuration, compared to the conventional solid baseline fan case rubstrip also tested. Performance results with the Soft Vanes showed that there was no measurable change in the corrected fan thrust and a 1.8 percent loss in corrected stator vane thrust, which resulted in a total net thrust loss of approximately 0.5 percent compared with the baseline reference stator vane set.

Hughes, Christoper E.↗
NASA NTRS2018

Analysis of the Honeywell Uncertified Research Engine (HURE) with Ice Crystal Cloud Ingestion at Simulated Altitudes: Public Version

The Honeywell Uncertified Research Engine (HURE), a research version of a turbofan engine that never entered production, was tested in the NASA Propulsion System Laboratory (PSL), an altitude test facility at the NASA Glenn Research Center. The PSL is a facility that is equipped with water spray bars capable of producing an ice cloud consisting of ice particles, having a controlled particle diameter and concentration in the air flow. In preparation for testing of the HURE, numerical analysis of flow and ice particle thermodynamics was performed on the compression system of the turbofan engine to predict operating conditions that could potentially result in a risk of ice accretion due to ice crystal ingestion. The results of those analyses formed the basis of the test matrix. The goal of the test matrix was to have ice accrete in two regions of the compression system: region one, which consists of the fan-stator through the inlet guide vane (IGV), and region two which is the first stator within the high pressure compressor. The predictive analyses were performed with the mean line compressor flow modeling code (COMDES-MELT) which includes an ice particle model. Together these comprise a one-dimensional icing tool. The HURE engine was tested in PSL with the ice cloud over the range of operating conditions of altitude, ambient temperature, simulated flight Mach number, and fan speed with guidance from the analytical predictions. The engine was fitted with video cameras at strategic locations within the engine compression system flow path where ice was predicted to accrete, in order to visually confirm ice accretion when it occurred. In addition, traditional compressor instrumentation such as total pressure and temperature probes, static pressure taps, and metal temperature thermocouples were installed in targeted areas where the risk of ice accretion was expected. The current research focuses on the analysis of the data that was obtained after testing the HURE engine in PSL with ice crystal ingestion. The computational method was enhanced by computing key parameters through the fan-stator at multiple spanwise locations, in order to increase the fidelity with the current mean-line method. In addition, other sources of heat (non-adiabatic walls) were suspected to be the cause of accretion near the splitter-lip and shroud. Since there were no thermocouples near the splitter, a simple order of magnitude heat transfer model was implemented to estimate the wall temperature. Future analyses will require a higher fidelity thermal analysis of the compression system metal walls to accurately calculate the total heat flux to the ice particle. For many data points analyzed, there were differences between the thermodynamic system model and the measured test data that may partially be responsible for uncertainties with the results of the current analyses.

Turbomachinery↗
NASA NTRS2019

CAMIEM: Compact Additively Manufactured Innovative Electric Motor

New manufacturing methods are needed to obtain innovative electric motor designs that have much higher power densities and/or efficiencies compared to the current state-of-the-art. Additive manufacturing offers the potential to radically change motor designs so that they have compact designs, multi-material components, innovative cooling, and optimally designed and manufactured components. New component designs enabled by additive manufacturing technologies have been designed and were fabricated to include the housing, rotors, stator cooling ring, a direct printed stator, and a wire embedded stator. The new components were integrated into the motor and tested evaluate the performance gains in comparison to the baseline electric motor configuration. Partners on the sub-project include NASA GRC, NASA LaRC, NASA AFRC, LaunchPoint Technologies, and the University of Texas El Paso.

Halbig, Michael C.↗
NASA NTRSDate not supplied

Electromagnetic Redesign of NASA’s High Efficiency Megawatt Motor

NASA’s High Efficiency Megawatt Motor (HEMM) is being developed to achieve the performance needed by single aisle class electrified aircraft. It is a 1.4 MW electric machine designed as a generator for NASA’s STARC-ABL concept vehicle. It has performance objectives of greater than 16 kW/kg electromagnetic specific power and efficiency of greater than 98%. A significant flaw in the preliminary electromagnetic design of HEMM was recently discovered. The stator teeth in the preliminary design cause the magnetic flux in the rotating components of HEMM to oscillate at a very high frequency (12,240 Hz). Two independent energy loss analyses are presented to show that the frequency is high enough to cause eddy current losses that significantly exceed the rotor’s loss limit (50 W), despite the very small magnitude of this flux oscillation (<0.01 T). To eliminate these rotor losses, while continuing to meet the target performance, it was determined that the stator teeth needed to be removed and the electromagnetic geometry of the motor needed to be revised. The revised, slotless HEMM motor design is summarized. Sensitivity of the new design to key unknown variables such as the temperature of and number of turns in the superconducting rotor coils and the stator winding’s average temperature.

Thomas T Tallerico↗
NASA NTRS2023

Assessment of Gaseous Helium Cooling in a Superconducting Coil Test Rig

An experimental rig was designed and constructed at the NASA Glenn Research Center to measure the alternating current (AC) losses of round, multifilament, superconducting (SC), magnesium diboride (MgB2) wire in the temperature range from 20 to 30 K. The rig resembles a permanent magnet (PM) motor with the stator windings omitted. Experiment packs containing the superconductor samples will be placed in the annular space between the rotor and the stator back iron. The original plan was to measure the AC losses by calorimetry using nonboiling liquid hydrogen as the cooling fluid. The present plan is to use helium gas (GHe) under a few bar pressure instead. This report summarizes the calculations that indicate that reasonable results can be obtained, even though the mass density of the GHe will be only a fraction of that of liquid hydrogen. It is necessary to show that the heat transfer coefficient from SC wire to GHe can be high enough, that the temperature rise of the He between the experiment inlet and outlet can be small enough, and that sufficient He flow can be driven by a commercially available He fan. Both straight wire samples to validate loss models and coils to simulate motor stator coils can be tested in the rig. The lowest superconductor temperature that is feasible to reach in the rig is estimated. The temperature range available for samples will be wider with the gaseous He system than it would have been with liquid hydrogen.

supeconductors↗
NASA NTRSDate not supplied

Scaling Electric Machines to a Megawatt and Material Options

Megawatt (MW) electric aircraft propulsion (EAP) is seen as a significant contributor toward achieving the goals set forth by the Sustainable Flight National Partnership. A large part of enabling MW EAP is developing specific-power-dense electric machines. As specific-power-dense electric machines are scaled up from kW to MW power levels, the thermal stresses on the machines increase in both magnitude and performance-affecting characteristics. This is particularly true for the stators of these machines. Analysis via thermal resistance network modeling and multiscale modeling reveals that increasing amounts of heat will be trapped in the stator windings as the power levels increase. The challenges this presents can be addressed through material advancements whereby materials gain multifunctionality. Specifically, the electrical insulation and potting materials, along with the electrical conductor, that compose the stator slot must work together (gain multifunctionality) to relieve the increased thermal stress. Materials research at the NASA Glenn Research Center points to some useful solutions in this trade space.

Electric Machine↗
NASA NTRS2023

Scaling Electric Machines to a Megawatt and Material Options

Megawatt (MW) electric aircraft propulsion (EAP) is seen as a significant contributor toward achieving the goals set forth by the Sustainable Flight National Partnership. A large part of enabling MW EAP is developing specific-power-dense electric machines. As specific-power-dense electric machines are scaled up from kW to MW power levels, the thermal stresses on the machines increase in both magnitude and performance-affecting characteristics. This is particularly true for the stators of these machines. Analysis via thermal resistance network modeling and multiscale modeling reveals that increasing amounts of heat will be trapped in the stator windings as the power levels increase. The challenges this presents can be addressed through material advancements whereby materials gain multifunctionality. Specifically, the electrical insulation and potting materials, along with the electrical conductor, that compose the stator slot must work together (gain multifunctionality) to relieve the increased thermal stress. Materials research at the NASA Glenn Research Center points to some useful solutions in this trade space.

Electric Machine↗
NASA NTRSDate not supplied

Numerical Investigation of Combustor-Turbine Interactions with a Two-Stage High-Pressure Turbine Including Cooling Airflows

Combustor–turbine interactions (CTIs) are investigated by performing three-dimensional unsteady simulations using a realistic combustor and high-pressure turbine (HPT) configurations from the Energy Efficient Engine (E3) program. To understand CTIs, we compare the numerically predicted flow fields from single-component simulations (Step 1: the combustor + the first-stage stator of turbine; Step 2: the two-stage HPT imposing the time-averaged flow solution from Step 1 as the inflow boundary condition) and a fully coupled combustor–turbine simulation (Step 3) at the sea-level takeoff (SLTO) condition. In addition to three previous simulations where the cooling airflows inside the HPT had been neglected for all Step 1, Step 2, and Step 3, two new simulations of Step 2 and Step 3 take into account the cooling airflows using the source team approach. In this approach, to mimic the cooling airflows, we impose the source term at a specific area of a cooling airflow hole at the solid surfaces without making a mesh of each hole. The objective of this study is twofold. One is to investigate the effect of the presence of the cooling airflows on the aerodynamics of the combustor and HPT as well as the HPT performance. The second is to perform a detailed comparison among the calculated flowfields by two different numerical schemes, the central-difference with the standard Jameson–Schmidt–Turkel (CD-JST) scheme and the AUSM scheme. There is a noticeable difference in the hot-streak distributions at the first-stage stator. In addition, depending on the choice of the numerical scheme and the presence of the cooling airflows, an occurrence of shock waves appearing at the first-stage stator is greatly influenced. Thus, this has a noticeable impact on the HPT performance. It is shown that the estimated turbine efficiencies from Step 3 are about 7 % less than the ones from Step 2.

Combustor-turbine interaction↗
NASA NTRSDate not supplied

Design and Optimization of an Open Rotor Stage

Open rotor propulsors enable greatly increased effective bypass ratios over current aircraft engines, resulting in significantly improved efficiencies. One of the most promising of these geometries is the “open fan”, which consists of a single rotor followed by a single stator. This configuration will be referred to as an “open rotor stage” for design work at NASA. In this work we consider the multidisciplinary design and optimization of an open rotor stage using a variety of 2D and 3D techniques. The 2D aerodynamic techniques used for design include a 2D Trefftz plane method, axisymmetric throughflow, and quasi-3D blade-to-blade CFD. Aerodynamic performance is prioritized, while structural requirements are met and some acoustic considerations are included. Between the rotor, stator, and hub profiles, a total of 101 design variables are used. Differences in the process of designing an open rotor stage vs. designing other high-speed propellers are also discussed. The current design, the NASA Optimized Propulsor for Efficiency and Noise (N-OPEN-1), achieves 84.7% net efficiency as predicted by 3D CFD, with further improvements expected to be possible. This design makes effective use of a slower rotor and a less tip-loaded work distribution than typical single-rotation propellers, allowing the stator to produce 14.8% of the thrust. Laminar flow on the blades was responsible for a 1.7% efficiency benefit and warrants further study.

Open rotors↗
NASA NTRS2026

Design and Optimization of an Open Rotor Stage

Open rotor propulsors enable greatly increased effective bypass ratios over current aircraft engines, resulting in significantly improved efficiencies. One of the most promising of these geometries is the “open fan”, which consists of a single rotor followed by a single stator. This configuration will be referred to as an “open rotor stage” for design work at NASA. In this work we consider the multidisciplinary design and optimization of an open rotor stage using a variety of 2D and 3D techniques. The 2D aerodynamic techniques used for design include a 2D Trefftz plane method, axisymmetric throughflow, and quasi-3D blade-to-blade CFD. Aerodynamic performance is prioritized, while structural requirements are met and some acoustic considerations are included. Between the rotor, stator, and hub profiles, a total of 101 design variables are used. Differences in the process of designing an open rotor stage vs. designing other high-speed propellers are also discussed. The current design, the NASA Optimized Propulsor for Efficiency and Noise (N-OPEN-1), achieves 84.7% net efficiency as predicted by 3D CFD, with further improvements expected to be possible. This design makes effective use of a slower rotor and a less tip-loaded work distribution than typical single-rotation propellers, allowing the stator to produce 14.8% of the thrust. Laminar flow on the blades was responsible for a 1.7% efficiency benefit and warrants further study.

turbomachinery↗
DOE OSTI2020

Validation and Parametric Investigations Using a Lumped Thermal Parameter Model of an Internal Permanent Magnet Motor: Preprint

One of the key challenges for the electric vehicle industry is to develop high-power-density electric motors. Achieving higher power density requires efficient heat removal from inside the motor. In order to improve thermal management, a multi-physics modeling framework that is able to accurately predict the behavior of the motor, while being computationally efficient, is essential. This paper first presents a detailed validation of a Lumped Parameter Thermal Network (LPTN) model of an Internal Permanent Magnet (IPM) synchronous motor within the commercially available Motor-CAD® modeling environment. The IPM motor’s stator is studied at steady state, and winding losses are generated by a constant DC current. The validation is based on temperature comparison with experimental data and with more detailed Finite Element Analysis (FEA). All critical input parameters of the LPTN are considered in detail for each layer of the stator, especially the contact resistances between the impregnation, liner, laminations and housing. Finally, a sensitivity analysis for each of the critical input parameters is provided. A maximum difference of 4% - for the highest temperature in the slot windings and the end windings - was found between the LPTN and the experimental data. Comparing the results from the LPTN and the FEA model, the maximum difference was 2% for the highest temperature in the slot windings and end windings. As for the LTPN sensitivity analysis, the thermal parameter with the highest sensitivity was found to be the liner-to-lamination contact resistance. The latter is often ignored in the literature, whereas its impact on temperature rise was found to be more significant than any other contact resistance within the stator.

ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

High speed induction machine

In one embodiment, a high speed induction machine includes: a stator formed of a first plurality of laminations having a thickness of less than approximately 0.01 inch and a winding comprising a coil formed of Litz wire adapted about the stator; and a rotor adapted within the stator. The rotor may include: a rotor core formed of a second plurality of laminations having a second thickness of greater than approximately 0.10 inch and formed of high strength steel and sandwiched between a first end region including at least one first peripheral second lamination and a second end region including at least one second peripheral second lamination, the first end region having a first end ring retained by a first retaining ring adapted there around, the second end region having a second end ring retained by a second retaining ring adapted there around.

Karmaker, Haran Chandra↗
DOE OSTI2023

Integrated electro-hydraulic machine

An integrated electromechanical and hydraulic system is disclosed which includes an electric machine, the electric machine includes a casing, a stator adapted to remain stationary within the casing, one or more electrically insulated windings coupled to the stator, a rotor separated from the stator and the one or more windings by a radial diamagnetic gap, electrical power couplings, and a first mechanical power couplings, and a hydraulic machine also disposed in the housing, the hydraulic machine having hydro-mechanical couplings as well as a second mechanical power couplings, wherein the second mechanical power couplings are coupled to the first mechanical power couplings.

Vacca, Andrea↗
DOE OSTI2024

Investigation of a Multi-Rotor Triboelectric Nanogenerator Using a Modular Flexible Circuit Board Stack

Triboelectric nanogenerators (TENGs) are a nascent class of energy harvester that are being explored for scavenging energy from small ocean waves. To date, they have been integrated in wave energy converters (WECs) designed to capture random motion caused by the perturbations of the ocean surface. Blue economy applications such as ocean observation can benefit greatly from more substantial wave-derived power, as such, the power output of existing TENG WECs must be increased several-fold to become viable. This study describes the conceptualization of a rotary TENG, and the subsequent efforts to increase its power output by stacking multiple stator and rotor pairs. In the latter part of this study, we introduce a novel means of incorporating a friction element into the design of the TENG by employing flexible printed circuit board (PCB) rotors. At rest, these flexible rotors will contact the stator, building static charges due to friction, at speed, these flexible rotors will be decoupled from the stator, reducing friction and allowing faster rotation. Initial results indicate that the power output of the flexible PCB rotor does not produce more power than a rigid, acrylic disk rotor, however the current output of the prototype is boosted, and the prototype is far more compact, allowing for a higher energy density than the rigid rotor prototype.

bench testing↗
DOE OSTI2024

Axial flux motor

Provided is an axial flux motor including a rotor having a wound ribbon core, the wound ribbon core including a metal amorphous nanocomposite material. The axial flux motor further includes a stator assembly spaced apart from the rotor along a rotation axis of the rotor. The stator assembly includes a body including a metal amorphous nanocomposite material and a plurality of permanent magnets substantially free of rare-earth materials. The plurality of permanent magnets is arranged on the body of the stator assembly.

Simizu, Satoru↗
DOE OSTI2020

A Comprehensive Review of Permanent Magnet Transverse Flux Machines: Use in Direct-Drive Applications

The use of direct-drive machines in renewable and industrial applications is increasing at a rapid rate. Transverse flux machines (TFMs) are ideally suited for direct-drive applications due to their high torque density. This article presents a comprehensive review of permanent magnet (PM) TFMs for direct-drive applications. It introduces TFMs and their operating principle and reviews the different types of TFMs proposed in the literature. TFMs are categorized by the number of stator sides, types of stator cores, and magnet arrangement in the rotor. The review covers different design topologies, materials used for manufacturing, structural and thermal analyses, modeling, design optimization, and cogging torque minimization in TFMs. The article also examines various applications and comparisons for TFMs presented in the literature.

air gaps↗
DOE OSTI2026

Power Electronic Development Challenges for High Power Density Integrated Electric Drive Applications

The ever-increasing demand for compact, efficient, and high-performance traction drive systems for transportation applications has accelerated the development of integrated electric drives. In these systems, the electric machine and inverter are integrated within a single housing, offering significant advantages in electrical performance, volume, weight, cost, and overall system efficiency. Despite these benefits, such high levels of integration introduce a new set of challenges, particularly in power electronic design and component selection. This article presents an in-depth investigation of a highly integrated electric drive architecture with an internal stator-mounted inverter, highlighting key design considerations and trade-offs aimed exclusively at maximizing system power density.Based on a comprehensive review of the literature, the power density of a voltage-source-inverter-driven electric drive is primarily governed by the volumetric contributions of the power modules, heat sinks, and DC-link capacitors. Accordingly, this work focuses on the optimization of these three critical components to enhance the inverter's overall power density. The proposed design achieves a power density of 100 kW/L, demonstrating the effectiveness of the presented approach for next-generation integrated electric drive systems.

33 ADVANCED PROPULSION SYSTEMS↗