Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Stainless Steel”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Irradiation effects on Al 0.3 CoCrFeNi and CoCrMnFeNi high-entropy alloys, and 316H stainless steel at 500 °C

To evaluate the potential of high entropy alloys (HEAs) for nuclear applications, two HEAs, Al 0.3 CoCrFeNi and CoCrFeMnNi, and a conventional Type 316H stainless steel (SS) were irradiated with 1 MeV krypton ions at 500 degrees C up to 1 dpa, and examined in-situ with a transmission electron microscope (TEM). After irradiation, a high density of ordered L1 2 nanoparticles was observed in Al 0.3 CoCrFeNi. In contrast, no phase transformation was observed in CoCrFeMnNi and 316H SS. In the thin foil regions of TEM samples, stacking-fault tetrahedra were observed in the HEAs. In the thick foil regions, interstitial dislocation loops were observed for all alloys, and the areal loop density increased linearly with foil thickness. The Al 0.3 CoCrFeNi had the largest loop size (the lowest density), followed by the CoCrFeMnNi and then the 316H SS. The higher loop nucleation rate in the 316H SS was attributed to carbon content. Finally, the degree of irradiation hardening was slightly lower for the HEAs than for the 316H SS, which is a promising sign for the nuclear application of HEAs at high temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Critical role of slags in pitting corrosion of additively manufactured stainless steel in simulated seawater

Abstract Pitting corrosion in seawater is one of the most difficult forms of corrosion to identify and control. A workhorse material for marine applications, 316L stainless steel (316L SS) is known to balance resistance to pitting with good mechanical properties. The advent of additive manufacturing (AM), particularly laser powder bed fusion (LPBF), has prompted numerous microstructural and mechanical investigations of LPBF 316L SS; however, the origins of pitting corrosion on as-built surfaces is unknown, despite their utmost importance for certification of LPBF 316L SS prior to fielding. Here, we show that Mn-rich silicate slags are responsible for pitting of the as-built LPBF material in sodium chloride due to their introduction of deleterious defects such as cracks or surface oxide heterogeneities. In addition, we explain how slags are formed in the liquid metal and deposited at the as-built surfaces using high-fidelity melt pool simulations. Our work uncovers how LPBF changes surface oxides due to rapid solidification and high-temperature oxidation, leading to fundamentally different pitting corrosion mechanisms.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Multi-scale experimental study of creep-fatigue failure initiation in a 709 Stainless Steel alloy using high resolution digital image correlation. Final report

This report discusses the efforts made towards the multi-scale study of the creep-fatigue response of stainless steel 709. Multiple experimental techniques, including digital image correlation (DIC) and electron backscatter diffraction (EBSD), were used in assessing the evolution of damage accumulation during fatigue, creep-fatigue, and thermomechanical fatigue of alloy 709. The role of microstructural features, hold times, temperature, and loading profiles were quantified and the interchangeability of temperature and time was investigated. Finally, a thermomechanical fatigue model was shown to predict well the failure of samples with varying loading profiles. Results indicate that strain accumulation in 709 steel happens primarily near grain boundaries (GBs) with the strains around GBs being inversely proportional to their measured residual burgers vector. Furthermore, hot-spots for strain accumulation were shown to be the locations of eventual microcrack nucleation. The introduction of hold times to the periodic loading cycle increases the damage accumulation rate and thus shortens the fatigue life of samples–this was true for both room temperature and high temperature. Thermomechanical cycling was shown to have little effect on the end life of samples, with the damage accumulation rate for in-phase and out-of-phase cycling being similar to isothermal fatigue. The interchangeability of time and temperature was shown to be possible within the studied load, time, and temperature ranges, since deformation mechanisms driving strain accumulation did not change with temperature (up to 650°C). The Neu-Sehitoglu thermomechanical fatigue model, with constants obtained from the literature and in part from our experimental results, was applied to predict failure of isothermal creep-fatigue samples. The main objectives of this work were to:(a) Perform high-resolution digital image correlation measurements (HiDIC) for alloy 709; (b) Quantify and assess damage accumulation at the microstructure under fatigue, TMF, and creep-fatigue conditions of 709; (c) Study of the role of hold times, i.e., adding a creep component, to: Room temperature cycling, High temperature cycling, Failure; (d) Study the mechanisms of thermomechanical fatigue in this alloy; (e) Investigate the existence of a time-temperature interchangeability criterion to aid in accelerated creep-fatigue testing; (f) Establish the validity of a combined creep-fatigue model for life prediction for 709. This report is structured with each subsequent section detailing the efforts, results, and conclusions related to each of the objectives described, mostly in chronological order.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Simulations of crack extensions in arc-shaped tension specimens of uncharged and hydrogen-charged 21-6-9 austenitic stainless steels using cohesive zone modeling with varying cohesive parameters

Crack extensions in uncharged and hydrogen-charged side-grooved A(T) specimens of conventionally forged 21-6-9 austenitic stainless steels are simulated using the cohesive zone modeling approach. Two-dimensional plane strain finite element analyses with fixed cohesive parameters are first conducted to fit the experimental load-displacement curves. Similar analyses using varying cohesive parameters as functions of the crack extension are then conducted to fit the experimental load-crack extension and crack extension-displacement curves. The computational results with varying cohesive parameters can fit very well the experimental data. The computational results also indicate that the average cohesive energy for the hydrogen-charged A(T) specimen is lower than that for the uncharged A(T) specimen.

42 ENGINEERING↗
DOE OSTI2021

Cathodic Kinetics on Platinum and Stainless Steel in NaOH Environments

During typical atmospheric conditions, cathodic reduction reactions produce hydroxyl ions increasing the pH in the cathodic region. Therefore, cathodic reduction reactions are investigated on platinum and stainless steel 304 L (SS304L) in NaOH solutions ranging in pH from 13.6 to 16.5. It was found that in solution pHs less than 16.5 the cathodic reduction reaction on Pt and SS304L was ORR with an electron transfer number less than two due to superoxide formation as an intermediate. Increasing pH decreased the number of electrons transferred. At a pH of 16.5, the cathodic reduction reaction on SS304L is no longer ORR and the cathodic current on the surface of the alloy is due to oxide reduction occurring on the surface as indicated by the creation of multi-component Pourbaix diagrams. The results of this study have important implications for predicting corrosion in atmospheric environments.

25 ENERGY STORAGE↗
DOE OSTI2022

Probing the Damage Recovery Mechanism in Irradiated Stainless Steels Using In-Situ Microcantilever Bending Test

Single crystalline microcantilevers are fabricated from the base metal and heat-affected zone (HAZ) of a laser welded, neutron irradiated austenitic stainless steel, for scanning electron microscope (SEM) in-situ bending. In the HAZ, cantilevers exhibit higher yield point and lower crack tip blunting displacement than in the base metal and unirradiated archive specimen. These results suggest that radiation-induced defects harden the base metal, whereas the HAZ exhibits annealing of defects leading to mechanical softening. Dislocation nucleation ahead of the crack tip is responsible for ductile blunting behavior and provides a pathway to mitigating helium-induced cracking during weld repairs of irradiated materials.

36 MATERIALS SCIENCE↗
DOE OSTI2025

In Situ Measurement of Stress Corrosion Crack Tip Properties During Environmentally Induced Cracking in Stainless Steel 304L

The influence of the external cathodic area, stress intensity, and electrochemical polarization level on the resultant crack growth rate and crack tip pH and potential was studied for stainless steel 304L in a sodium chloride environment. Before testing, the validity of in situ crack tip property measurements using microprobes and drilled holes was supported through modeling efforts and confirmed with experimental observations. Here, it was found that increasing the R-ratio during corrosion fatigue increased the crack growth rate and decreased the measured crack tip pH of the 304L sample. Decreasing the electrochemical potential (i.e., cathodic polarization) of the bulk sample increased the crack tip pH and stopped measured crack extension under constant K conditions. Conversely, increasing the potential of the bulk sample decreased the crack tip pH and induced cracking under constant K conditions. Decreasing the cathodic area external to the crack increased the measured pH at the crack tip and decreased the crack growth rate under fatigue conditions. For the given configuration, environment, and alloy studied, fatigue crack growth is not sustained by cathodic reactions solely occurring in the crack wake and notch. These results have implications for the ability to predict atmospheric crack growth rates from laboratory, full immersion experiments.

corrosion fatigue↗
NASA NTRS2005

Stainless-Steel-Foam Structures Evaluated for Fan and Rotor Blades

The goal of this project is to use a sandwich structure design, consisting of two stainlesssteel face sheets and a stainless-steel-foam core, to fabricate engine fan and propeller blades. Current fan blades are constructed either of polymer matrix composites (PMCs) or hollow titanium alloys. The PMC blades are expensive and have poor impact resistance on their leading edges, thereby requiring a metallic leading edge to satisfy the Federal Aviation Administration s impact requirements relating to bird strikes. Hollow titanium blades cost more to fabricate because of the intrinsically difficult fabrication issues associated with titanium alloys. However, both these current concepts produce acceptable lightweight fan blades.

Lerch, Bradley A.↗
DOE OSTI2022

Extreme variation in fatigue: Fatigue life prediction and dependence on build volume location in laser powder bed fusion of 17-4 stainless steel

Laser powder bed fusion (LPBF), a metal additive manufacturing technology, is well-suited for design optimization but fatigue life is limited by manufacturing defects. In this work, 17-4 stainless steel components were manufactured in densely populated build volumes, simulating at-scale LPBF production. Tests revealed extreme variability in fatigue life data, analyzed via rigorous statistical tools. The El-Haddad model, modified for finite-life, enabled defect-based life prediction. Specimen location within the build volume correlated to life, which was heteroscedastic. Investigating defect concentration over the build volume explained typical life and scatter. Finally, these findings argue for qualification approaches which acknowledge high material lot variability.

36 MATERIALS SCIENCE↗
NASA NTRS1976

Application of strainrange partitioning to the prediction of creep-fatigue lives of AISI types 304 and 316 stainless steel

As a demonstration of the predictive capabilities of the method of Strainrange Partitioning, published high-temperature, low cycle, creep-fatigue test results on AISI Types 304 and 316 stainless steel were analyzed and calculated, cyclic lives compared with observed lives. Predicted lives agreed with observed lives within factors of two for 76 percent, factors of three for 93 percent, and factors of four for 98 percent of the laboratory tests analyzed. Agreement between observed and predicted lives is judged satisfactory considering that the data are associated with a number of variables (two alloys, several heats and heat treatments, a range of temperatures, different testing techniques, etc.) that are not directly accounted for in the calculations.

Saltsman, J. F.↗
NASA NTRS1977

Application of Strainrange Partitioning to the prediction of creep-fatigue lives of AISI Types 304 and 316 stainless steel

As a demonstration of the predictive capabilities of the method of Strainrange Partitioning, published high-temperature, low cycle, creep-fatigue test results on AISI Types 304 and 316 stainless steel were analyzed and calculated cyclic lives compared with observed lives. Predicted lives agreed with observed lives within factors of two for 76 percent, factors of three for 93 percent, and factors of four for 98 percent of the laboratory tests analyzed. Agreement between observed and predicted lives is judged satisfactory considering that the data are associated with a number of variables (two alloys, several heats and heat treatments, a range of temperatures, different testing techniques, etc.) that are not directly accounted for in the calculations.

Saltsman, J. F.↗
DOE OSTI2022

USE OF TWO-PISTON SPLAT QUENCHING TO INVESTIGATE & CHARACTERIZE THE IMPACT OF COMPOSITIONAL VARIATIONS ON RAPID SOLIDIFICATION MICROSTRUCTURES & SUB-MICROSCALE FEATURES IN STAINLESS STEEL ALLOY.

The objective of this dissertation was to use two-piston splat quenching (SQ) to investigate the impact of compositional modifications on the solidification and microstructure of rapidly solidified austenitic stainless steels (SS) and to demonstrate the ability of SQ to quickly and effectively simulate rapid solidification conditions similar to those found in powder bed fusion (PBF) additive techniques. PBF techniques like laser powder bed fusion (LPBF) are being implemented across a breadth of research and industrial applications to create parts with complex geometries and performance capabilities while pushing the current limits of processing conditions and understanding of material systems. In this work, SQ was used to experimentally produce rapid solidification in 20+ unique austenitic SS compositions with systematic variations of the chrome and nickel equivalency ratio (Cr/Nieq) through targeted compositional modifications. From the targeted change of Cr, Ni, and Mo concentrations in rapidly solidified SS alloys, the ferrite solidification mode was found to be the primary solidification mode at significantly lower Cr/Nieq than previously predicted for RS. Also, decreasing concentrations of Fe at a constant Cr/Nieq ratio (i.e., different Fe isopleths), or increased Mo concentrations at a constant Cr/Nieq ratio were found to suppress the ferrite to austenite massive transformation when compared to alloys with lower concentrations at the same Cr/Nieq. Using an established empirical relationship between cell size and cooling rate, the SQ technique was estimated to produce cooling rates between 106 and 108 K/s. Thermal gradients were extracted from 2-D heat transfer simulations of the SQ solidification event and used with these cooling rates to produce solidification rate estimates for SQ which were between 0.4-1.6m/s. The primary solidification mode was observed to be the determining factor in which elements segregated to the cell boundaries during RS, for which Cr and Mo were the main elements to segregate during primary austenite solidification and Ni during primary ferrite solidification. Finally, the solidification rates and conditions produced by SQ experiments resulted in similar microstructures, features, and microsegregation to what was found in LPBF samples of the same feedstock.

Hasenbusch, Zachary↗
DOE OSTI2019

Numerical Analysis of Molten Pool Behavior and Spatter Formation with Evaporation During Selective Laser Melting of 316L Stainless Steel

During the selective laser-melting process, material evaporation and resultant spatter are common phenomena that bring about many defects. However, the underlying physical phenomena such as molten pool behavior and spatter formation, as evaporation occurred, are sparsely understood and difficult to observe during the process. Thus, a three–dimensional powder-scale model was established to investigate the thermal and flow behavior of the molten pool, the morphology evolution of the molten pool and keyhole, and the spatter formation with evaporation in the selective laser-melting processing of 316L stainless steel. Phase transitions and variations in interfacial force were taken into account in this model. The modified phase-field method was applied to trace the melt–gas interface. The results showed that keyhole formed in molten pool under recoil pressure, and that there were some differences in the temperature distribution and flow behavior inside and outside the keyhole. In addition, the dimension and surface morphology of the molten pool and keyhole depth altered and gradually stabilized during the process. Moreover, droplet spatter formation at rear of molten pool proceeded roughly as follows: the backward ejection of melt vapor would induce a depression in molten pool and a bump on the molten pool surface, the bump moved backward and subsequently a liquid column formed, then the liquid column formed a neck and gradually pinched off, resulting in the droplet spatter. Furthermore, the characteristic morphology of the scan track and dimension of the molten pool were obtained through experiments, which showed good agreement with the simulation results.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Tensile behavior and microstructural evolution of a Fe-25Ni-20Cr austenitic stainless steel (alloy 709) from room to elevated temperatures through in-situ synchrotron X-ray diffraction characterization and transmission electron microscopy

Uniaxial tensile tests were done on Fe-25Ni-20Cr Austenitic Stainless Steel (Alloy 709) along with in-situ synchrotron measurement at different temperatures (25 degrees C, 500 degrees C, 700 degrees C and 900 degrees C). The X-Ray diffraction data was collected in-situ in order to follow the phases present as well as to derive the dislocation density as a function of strain through peak broadening analysis based on the modified Williamson-Hall method and see how trends are affected as a function of temperature. The XRD data were complemented by TEM and STEM-EDX characterization done on the post-experiment samples to observe the deformed microstructures. Finally, the paper presents a depiction of the tensile behavior of this advanced steel by interpreting the stress-strain curves and the effect of temperature through the information gained by in-situ XRD and TEM observations as well as fractography done ex-situ on the samples tested to rupture.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Ultrasonic characterization of material heterogeneities in stainless steel components produced by laser powder bed fusion

We introduce pulse-echo ultrasound as a method for characterizing the impact of powder bed fusion parameters on the properties of additively manufactured stainless-steel components, their material anisotropy, and location-dependent heterogeneity. Our results indicate that accurate characterization requires careful selection of ultrasonic propagation paths, which must consider the direction of additive layering, variations in processing parameters, and the component's geometry. We employed two distinct methods to estimate material properties from ultrasonic data: One assumes isotropy, while the other accounts for anisotropic interactions during the propagation of elastic waves. When applied to samples fabricated with laser energy densities ranging from 24 to 42 J/mm³ , these methods revealed transverse isotropy and weak anisotropy (quantified by small Thomsen parameters, ε = 0.0651 and γ = 0.0092) and less than a ∼6 % change in acoustic impedance. The assumption of isotropy, in this case, leads to small errors (less than 4 % or 1 % for Young's modulus in the build or transverse directions) when estimating orthotropic material properties using ultrasonic data measured along just two orthogonal directions, one of which must align with the build direction. By comparing ultrasonic measurements — which aggregate the spatial variability in material properties along the length of elastic wave propagation into a single value — with localized measurements obtained from surface nanoindentation, we uncovered and spatially profiled significant differences between the surface and interior properties. Specifically, the surface Young's modulus decreased from approximately 210 GPa to 180 GPa within a depth of about 3 mm. We attribute this surface-localized heterogeneity in PBF-fabricated components to distinct thermal histories experienced by the surface and interior regions. Collectively, the results of this study establish a framework for the ultrasonic characterization of material heterogeneity and anisotropy in material properties and demonstrate its application in additively manufactured metal components.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Process–Property–Performance Mapping of Additively Manufactured 316H Stainless Steel Components

The Advanced Materials and Manufacturing Technologies Program is focused on accelerating the development of advanced materials and components fabricated via additive manufacturing, and is using laser powder bed fusion (LPBF) of 316H stainless steel as an initial case study. In the previous fiscal year, miniature high-throughput specimens were printed on multiple LPBF systems to provide initial processing windows to minimize porosity and limit epitaxial grain growth during prints. This fiscal year, scaled builds were completed on three different LPBF systems at ORNL: a GE Concept Laser M2, a Renishaw AM400, and an EOS M290. Builds on the Concept Laser were conducted on multiple powder lots and processing parameter ranges to provide microstructure effects on time-independent and time-dependent mechanical properties. Builds on the Renishaw were produced using Oak Ridge National Laboratory (ORNL)-optimized printing parameters and Argonne National Laboratory (ANL)-optimized printing parameters to compare outcomes of parallel process optimization efforts at different national laboratories on the same LPBF system. Similarly, the build completed on the EOS M290 replicated the processing parameters of builds completed at Los Alamos National Laboratory (LANL). Optical microscopy and electron backscatter diffraction characterization was completed on all builds. In addition to the general round robin characterization, this work-package generated time-independent data, including tensile and fracture toughness test data on scaled Concept Laser builds as a function of processing parameters and post-build heat treatment. This analysis is complimentary to work in parallel work packages aiming to establish heat treatment and processing effects on time-dependent properties. It was found that although the stress-relief heat treatment provides the highest strength at lower-temperatures, tensile strength begins to converge at higher temperatures regardless of heat treatment condition. In addition, the more rigorous solution annealing and hot-isostatic pressing post-build heat treatments result in higher fracture toughness than the stress-relieved condition. The root-causes of the lower fracture toughness of the stress-relieved LPBF 316H material was informed via a stress-relief optimization study on a scaled concept laser print, where it was found that although dislocation recovery was largely complete after only a couple hours at 650°C, the extended hold of the current 24h heat treatment employed on scaled builds likely caused increased carbide volume fractions along the LPBF 316H grain boundaries, thereby deteriorating crack propagation resistance. This trend was seen to become more deleterious with additional increases of stress-relief temperature to 750°C or 850°C. These results have helped inform a new optimal stress-relief annealing condition for LPBF 316H for future campaign testing (650°C for 2h).

36 MATERIALS SCIENCE↗