Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solidification microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

Solidification and Re-melting Phenomena During Slurry Preparation Using the RheoMetal™ Process

The melting sequence of the enthalpy exchange material (EEM) and formation of a slurry in the RheoMetal™ process was investigated. The EEM was extracted and quenched, together with a portion of the slurry at different processing times before complete melting. The EEM initially increased in size/diameter due to melt freezing onto its surface, forming a freeze-on layer. The initial growth of this layer was followed by a period of a constant diameter of the EEM with subsequent melting and decrease of diameter. Microstructural characterization of the size and morphology of different phases in the EEM and in the freeze-on layer was made. Dendritic equiaxed grains and eutectic regions containing Si particles and Cu-bearing particles and Fe-rich particles were observed in the as-cast EEM. The freeze-on layer consisted of dendritic aluminum tilted by about 30 deg in the upstream direction, caused by the rotation of the EEM. Energy dispersion spectroscopy analysis showed that the freeze-on layer had a composition corresponding to an alloy with higher melting point than the EEM and thus shielding the EEM from the surrounding melt. Microstructural changes in the EEM showed that temperature rapidly increased to 768 K (495 °C), indicated by incipient melting of the lowest temperature melting eutectic in triple junction grain boundary regions with Al{sub 2}Cu and Al{sub 5}Mg{sub 8}Si{sub 6}Cu{sub 2} phases present. As the EEM temperature increased further the binary Al-Si eutectic started to melt to form a region of a fully developed coherent mushy state. Experimental results and a thermal model indicated that as the dendrites spheroidized near to the interface at the EEM/freeze-on layer reached a mushy state with 25 pct solid fraction, coherency was lost and disintegration of the freeze-on layer took place. Subsequently, in the absence of the shielding effect from the freeze-on Layer, the EEM continued to disintegrate with a coherency limit of a solid fraction estimated to be 50 pct.

36 MATERIALS SCIENCE↗

Strength mechanisms and tunability in Al-Ce-Mg ternary alloys enabled by additive manufacturing

Al-Ce-based alloys are promising candidates for additive manufacturing (AM) due to their hot-cracking resistance and because they do not require heat treatment to obtain precipitation strengthening. Rapid solidification rates enabled by AM methods can lead to enhanced mechanical properties; however, the strengthening mechanisms over large composition ranges were unclear. Here, combinatorial synthesis by directed-energy deposition (DED) and hardness measurements were used to rapidly map the composition-dependent strength of the ternary Al-Ce-Mg system. Tensile testing and microstructure characterization of selected compositions were performed to elucidate the compositional dependence of the strengthening mechanisms. Al 11 Ce 3 precipitates were present in all cases, and the maximum hardness (1.25 GPa) was measured for the Al-8Ce-10Mg composition. A combination of (i) Hall-Petch strengthening, based on the FCC-matrix-phase cell size; (ii) particle strengthening, based on Al 11 Ce 3 volume fraction and size; and (iii) solid-solution strengthening, based on Mg composition of the matrix phase, were used to account for the measured strengths. Vickers hardness is shown to correlate well with ultimate tensile strength in these alloys, highlighting the value of surface-based techniques for rapid screening.

36 MATERIALS SCIENCE↗

Part-scale microstructure prediction for laser powder bed fusion Ti-6Al-4V using a hybrid mechanistic and machine learning model

Laser powder bed fusion (LPBF) Ti-6Al-4V is widely studied for use in structural applications in aerospace and medical industries, but mechanical anisotropy and microstructural inhomogeneity prohibits its wider adoption. Although successful microstructure prediction models have been developed, a remaining challenge is their limited integration across length/time scales and validation by experimental studies. Here, this work proposes a physics-augmented machine learning surrogate model to unite predictions of LPBF temperature, β phase morphology and texture, and α/α’ formation into a single framework that is calibrated and validated with experiments. First, a phase field (PF) model of the martensitic β→α’ transformation is developed and calibrated using data from in-situ synchrotron cyclic heating/cooling studies quantifying the variation of α phase fraction with time. In parallel, an established finite difference-Monte Carlo (FDMC) model predicts the part-scale temperature profile and β grain formation during solidification. A dataset is developed using LPBF cyclic temperature descriptors from the FDMC model as inputs and corresponding α/α’ phase fraction and width from the PF model as outputs. Five machine learning (ML) regression models are tested and optimized, having mean absolute error in testing ≤ 4 %, and the k-nearest neighbors (KNN) model is selected as the best performing. The KNN model is called at the nodal level during post-processing of the FDMC model to replace and downscale the response of the PF model. The combined agility and accuracy of the hybrid FDMC-ML model enables part-scale microstructure predictions that can be further used for property predictions to accelerate AM process optimization.

36 MATERIALS SCIENCE↗

High-Resolution Electron Microscopy and Kinetic Studies of Precipitation Hardening Reactions in Cast Al-5.8Zn-2.2Mg-2.5Cu

Precipitation age hardening (T6) response of Al-5.8Zn-2.2Mg-2.5Cu alloy in near-net-shaped cast condition was investigated. Cast samples were manufactured using the controlled diffusion solidification (CDS) technology combined with a metallic mold tilt pour gravity casting process. This study was conducted using (1) non-isothermal aging during differential scanning calorimetry (DSC) experiments and (2) isothermal aging during which transient bulk and micro-hardness measurements taken at four aging temperatures of 343, 393, 433 and 473 K. A detailed microstructural investigation combined with a quantitative image analysis was carried out on both DSC and hardness specimens using high-resolution electron microscopy (HREM) and energy-dispersive spectroscopy (EDS) elemental mappings. Hardness measurements were analyzed using a kinetic modeling approach (single state variable combined with a kinetic equation that is valid for the Al-Zn-Mg-Cu alloys). The results confirm the formation of hardening phases of GP zone, intermediate hardening metastable phase η′ and equilibrium phase η. The results of calorimetric measurements, electron microscopy and selected area diffraction patterns are in good agreement and confirm transient precipitation/dissolution sequences. A mean value of activation energy Q{sub A} of 75 kJ/mol was evaluated for combined bulk diffusion rate of alloying elements during precipitation of strengthening phases within Al matrix.

36 MATERIALS SCIENCE↗

The Effect of Weld Metal Composition on Microstructural and Mechanical Properties of Dissimilar Welds Between Monel 400 and Inconel 600

The current work was carried out to characterize welding of Inconel 600 superalloy and Monel 400. In the present study, gas tungsten arc welding (GTAW) with four types of filler metals (ENiCu, ENiCu-7, ENiCr-3 and ENiCrFe-3) was utilized. The filler metals were categorized into two groups based on the presence of Cr and Nb in their chemical composition. This paper describes the selection and application of welding consumables in manufacturing dissimilar metal combinations. It was found that (Nb/Cr) ratio and Fe content can affect on the size and amount of carbides. During solidification of ENiCr-3 and ENiCrFe-3 filler metals, Nb leaves dendritic cores and is rejected to inter-dendritic regions because of its high tendency for segregation. However, No brittle Laves phase was detected in the welds. The interface between weld metal and base metal and gradual changes in alloying elements were also investigated by scanning electron microscopy. EDX analysis was also applied for different samples. Microhardness measurements and tensile test were performed on the joints. The average hardness value in the weld metal obtained from ENiCrFe-3 is higher than the other welds. ENiCu-7 weld exhibited the highest tensile strength of 540 MPa and percent elongation of 53% in contrast to ENiCrFe-3 weld with the lowest tensile strength (518 MPa) and percent elongation (39%).

36 MATERIALS SCIENCE↗

Interfacial characteristics of P91 steel - Inconel 740H bimetallic structure fabricated using wire-arc additive manufacturing

Although bimetallic structures can offer unique solutions to engineering problems with varying functionality, joining two dissimilar alloys using additive manufacturing involves challenges such as cracking and segregation. In this work, bimetallic structures of Inconel 740H superalloy and P91 steel are processed using wire-arc additive manufacturing (WAAM) for the first time. P91 steel is directly deposited over 740H with a cooling time of 20 minutes in between the two depositions. During microstructure characterization, a large gradient zone with coarse grains spanning for ~2200 μm is observed. Moreover, the microhardness of the gradient zone is the least in comparison with the P91 and 740H deposits. No deleterious phase formation is found; however, intergranular cracks are observed along the gradient zone. In order to deduce the reason for cracking, non-equilibrium solidification simulations are performed for the mixed compositions of P91 and 740H in the gradient zone. Here, the reasons for crack formation in the gradient zone are the sudden change in the volumetric coefficient of thermal expansion due to the formation of MC carbides as well as the development of local strains from the thermal residual stresses. Therefore, altering the deposition sequence and introducing gradient layers with mixed composition between the P91 and 740H deposits will be beneficial in achieving defect-free builds. Through the integration of experiments and simulation, this work gains valuable insights into the processability of dissimilar alloy manufacturing using the WAAM technique.

20 FOSSIL-FUELED POWER PLANTS↗

Process-dependent anisotropic thermal conductivity of laser powder bed fusion AlSi10Mg: impact of microstructure and aluminum-silicon interfaces

Purpose AlSi10Mg alloy is commonly used in laser powder bed fusion due to its printability, relatively high thermal conductivity, low density and good mechanical properties. However, the thermal conductivity of as-built materials as a function of processing (energy density, laser power, laser scanning speed, support structure) and build orientation, are not well explored in the literature. This study aims to elucidate the relationship between processing, microstructure, and thermal conductivity. Design/methodology/approach The thermal conductivity of laser powder bed fusion (L-PBF) AlSi10Mg samples are investigated by the flash diffusivity and frequency domain thermoreflectance (FDTR) techniques. Thermal conductivities are linked to the microstructure of L-PBF AlSi10Mg, which changes with processing conditions. The through-plane exceeded the in-plane thermal conductivity for all energy densities. A co-located thermal conductivity map by frequency domain thermoreflectance (FDTR) and crystallographic grain orientation map by electron backscattered diffraction (EBSD) was used to investigate the effect of microstructure on thermal conductivity. Findings The highest through-plane thermal conductivity (136 ± 2 W/m-K) was achieved at 59 J/mm 3 and exceeded the values reported previously. The in-plane thermal conductivity peaked at 117 ± 2 W/m-K at 50 J/mm 3 . The trend of thermal conductivity reducing with energy density at similar porosity was primarily due to the reduced grain size producing more Al-Si interfaces that pose thermal resistance. At these interfaces, thermal energy must convert from electrons in the aluminum to phonons in the silicon. The co-located thermal conductivity and crystallographic grain orientation maps confirmed that larger colonies of columnar grains have higher thermal conductivity compared to smaller columnar grains. Practical implications The thermal properties of AlSi10Mg are crucial to heat transfer applications including additively manufactured heatsinks, cold plates, vapor chambers, heat pipes, enclosures and heat exchangers. Additionally, thermal-based nondestructive testing methods require these properties for applications such as defect detection and simulation of L-PBF processes. Industrial standards for L-PBF processes and components can use the data for thermal applications. Originality/value To the best of the authors’ knowledge, this paper is the first to make coupled thermal conductivity maps that were matched to microstructure for L-PBF AlSi10Mg aluminum alloy. This was achieved by a unique in-house thermal conductivity mapping setup and relating the data to local SEM EBSD maps. This provides the first conclusive proof that larger grain sizes can achieve higher thermal conductivity for this processing method and material system. This study also shows that control of the solidification can result in higher thermal conductivity. It was also the first to find that the build substrate (with or without support) has a large effect on thermal conductivity.

Engineering↗

Degradation science: Integrating modeling and experiments to predict localized corrosion processes (Annual Progress Report)

Additively manufactured (AM) eutectic high-entropy alloys (EHEAs), such as nano-lamellar AlCoCrFeNi 2.1 , have excellent strength, ductility, and wear resistance even at elevated temperatures, but their corrosion behavior in aggressive acids at different length scales remain poorly understood. This work investigates the corrosion behavior of laser powder bed–fused (L-PBF) AlCoCrFeNi 2.1 as a function of annealing temperatures, probing degradation mechanisms from nanoscopic to macroscopic length scales. The alloy is dual phase consisting of a ductile FCC L1 2 phase and a high-strength BCC B2 phase. Rapid solidification during L-PBF produces a far-from-equilibrium nano-lamellar structure with nearly homogeneous elemental distribution, which tends to evolve upon annealing toward Cr/Co/Fe-enriched FCC and Al/Ni-enriched B2. Three conditions were studied: as-printed, 600 °C/5 h, and 1000 °C/1 h, over which B2 lamellae coarsen, lamellar spacing increases, and elemental segregation becomes more prominent. Microstructure and chemistry were characterized by scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS), while in-situ electrochemical atomic force microscopy (EC-AFM) was used to link early (<5 h) local dissolution to microstructure after exposure in sulfuric acid. EC-AFM highlights preferential dissolution of the BCC/B2 phase where the surrounding matrix is Cr-depleted and directly quantifies the dissolution rates within individual phases, tracks the transition from early nano-scale attack to partial repassivation, to correlate height differences with current and impedance responses. To monitor longer-term behavior (up to 96 h), ex-situ AFM, SEM, and confocal imaging were combined with conventional bulk electrochemical tests, bridging nanoscale observations to micro/meso-scale damage morphologies. At the meso-scale, the deepest dissolution channels align with the build-direction lamellae and melt-pool boundaries, indicating that printing directionality guides the propagation of these localized corrosion sites. Annealing modifies corrosion by restructuring BCC/FCC phase fractions, lamellar spacing, and Cr/Al segregation, thereby changing the cathode/anode ratio and passive film stability. The results clarify how as-printed and annealed nano-lamellar architectures differ in their susceptibility to selective dissolution; how elemental segregation competes with residual stresses along the build direction. With these insights, future work will use CALPHAD-guided alloy modification to stabilize higher Cr contents in the B2 phase while retaining a dominant FCC+B2/BCC microstructure, with the goal of designing mechanically robust, corrosion-resistant EHEAs for safety-critical applications to leverage the LLNL’s broader national and global security mission.

36 MATERIALS SCIENCE↗

Characterization of an aluminum alloy hemispherical shell fabricated via direct metal laser melting

The ability of additive manufacturing to directly fabricate complex shapes provides characterization challenges for part qualification. The orientation of the microstructures produced by these processes will change relative to the surface normal of a complex part. In this work, the microscopy and x-ray tomography of an AlSi10Mg alloy hemispherical shell fabricated using powder bed metal additive manufacturing are used to illustrate some of these challenges. The shell was manufactured using an EOS M280 system in combination with EOS-specified powder and process parameters. The layer-by-layer process of building the shell with the powder bed additive manufacturing approach results in a position-dependent microstructure that continuously changes its orientation relative to the shell surface normal. X-ray tomography was utilized to examine the position-dependent size and distribution of porosity and surface roughness in the 98.6% dense part. Optical and electron microscopy were used to identify global and local position-dependent structures, grain morphologies, chemistry, and precipitate sizes and distributions. The rapid solidification processes within the fusion zone (FZ) after the laser transit results in a small dendrite size. Cell spacings taken from the structure in the middle of the FZ were used with published relationships to estimate a cooling rate of ~9 × 10 5 K/s. Uniformly-distributed, nanoscale Si precipitates were found within the primary α-Al grains. A thin, distinct boundary layer containing larger α-Al grains and extended regions of the nanocrystalline divorced eutectic material surrounds the FZ. Moreover, subtle differences in the composition between the latter layer and the interior of the FZ were noted with scanning transmission electron microscopy (STEM) spectral imaging.

36 MATERIALS SCIENCE↗

A stochastic scan strategy for grain structure control in complex geometries using electron beam powder bed fusion

Spatial control of microstructure within a three-dimensional component has been a dream of materials scientists for centuries. However, limitations in traditional manufacturing processes prevent detailed control over the distribution of microstructures in a single part. Here, we demonstrate the ability to control grain structure and crystallographic texture during metal additive manufacturing for arbitrary cross-sections of a practical size, with profound implications for the design and optimization of next-generation products. The key to this advance is a new geometry agnostic scan path algorithm that manipulates the spatial distribution of solidification conditions. Utilizing a fundamental understanding of solidification dynamics and a model of the heat transfer during processing, we have designed this algorithm to manipulate the natural competition between epitaxial dendrite growth and grain nucleation. With this algorithm, we successfully controlled the grain structure of Ni-based superalloy IN718 in the shape of the Mona Lisa.

36 MATERIALS SCIENCE↗

Thermal evolution behavior of carbides and {gamma} Prime precipitates in FGH96 superalloy powder

The characteristics of rapidly solidified FGH96 superalloy powder and the thermal evolution behavior of carbides and {gamma} Prime precipitates within powder particles were investigated. It was observed that the reduction of powder size and the increase of cooling rate had transformed the solidification morphologies of atomized powder from dendrite in major to cellular structure. The secondary dendritic spacing was measured to be 1.02-2.55 {mu}m and the corresponding cooling rates were estimated to be in the range of 1.4 Multiplication-Sign 10{sup 4}-4.7 Multiplication-Sign 10{sup 5} K{center_dot}s{sup -1}. An increase in the annealing temperature had rendered the phase transformation of carbides evolving from non-equilibrium MC Prime carbides to intermediate transition stage of M{sub 23}C{sub 6} carbides, and finally to thermodynamically stable MC carbides. The superfine {gamma} Prime precipitates were formed at the dendritic boundaries of rapidly solidified superalloy powder. The coalescence, growth, and homogenization of {gamma}' precipitates occurred with increasing annealing temperature. With decreasing cooling rate from 650 Degree-Sign C{center_dot}K{sup -1} to 5 Degree-Sign C{center_dot}K{sup -1}, the morphological development of {gamma} Prime precipitates had been shown to proceed from spheroidal to cuboidal and finally to solid state dendrites. Meanwhile, a shift had been observed from dendritic morphology to recrystallized structure between 900 Degree-Sign C and 1050 Degree-Sign C. Moreover, accelerated evolution of carbides and {gamma}' precipitates had been facilitated by the formation of new grain boundaries which provide fast diffusion path for atomic elements. - Highlights: Black-Right-Pointing-Pointer Microstructural characteristic of FGH96 superalloy powder was investigated. Black-Right-Pointing-Pointer The relation between microstructure, particle size, and cooling rate was studied. Black-Right-Pointing-Pointer Thermal evolution behavior of {gamma} Prime and carbides in loose FGH96 powder was studied.

36 MATERIALS SCIENCE↗

Microstructural refinement in ultrasonically modified A356 aluminum castings

Two A356 aluminum alloys (Al-Si-Mg), one with 0.09 wt.% Fe and one with 0.91 wt.% Fe, were cast in a graphite mold with the simultaneous application of local ultrasonic intensification to refine the as-cast microstructure. Ultrasonication during casting transformed the morphology of primary Al grains from dendritic (~140-290 microns in size) to globular (~33-36 microns in size). The alloy with high Fe exhibited globular grains at distances up to 45 mm away from the ultrasound probe, while the alloy with low Fe exhibited globular grains at distances only up to 6 mm away from the ultrasound probe. Near the location of the ultrasound probe (< 2 mm away), a second non-dendritic microstructural morphology was observed with fine aluminum grains (~9-25 microns in size). This unique fine-grained morphology has not been previously reported, contains a greater concentration of Si relative to the globular microstructure, and may be a large, fully eutectic region. Ultrasonication during casting also transformed the morphology of the ß-Al 5 FeSi phase particles (which are deleterious to the strength and ductility of the alloy) in the high Fe alloy from needle-like to rectangular, which could enable the greater use of secondary Al alloys. Thermodynamic simulations conducted to calculate the solidification paths of the two alloys studied predict that the ß-Al 5 FeSi phase begins to form earlier in the alloy with high Fe. Finally, data suggest that the ß-Al 5 FeSi phase (which is more abundant in alloys with high Fe content) may enhance ultrasonically-induced grain refinement.

36 MATERIALS SCIENCE↗

Nanostructure and compositional segregation of soft magnetic FeNi-based nanocomposites with multiple nanocrystalline phases

Soft magnetic metal amorphous nanocomposite alloys are produced through rapid solidification and thermal annealing yielding nanocrystals embedded within an amorphous precursor. Similar free energies in Co-rich and FeNi-based alloy systems result in multiple nanocrystalline phases being formed during devitrification. Studies of multi-phase crystallization processes have been reported for Co-rich alloys but relatively few have investigated FeNi-based systems. A detailed characterization of compositional partitioning and microstructure of an optimally annealed FeNi-based MANC (Fe 70 Ni 30 ) 80 Nb 4 Si 2 B 14 alloy is presented through complementary high-resolution transmission electron microscopy (HRTEM) and atom probe tomography (APT). HRTEM demonstrates orientation relationships between FCC and BCC nanocrystals, suggesting heterogeneous nucleation of nanocrystals in the amorphous matrix or a cooperative mechanism of nucleation between BCC and FCC nanocrystallites. APT results show evidence for (i) the segregation of Fe and Ni between nanocrystals of different phases, (ii) B partitioning to the amorphous phase, and (iii) an Nb-enriched shell surrounding nanocrystals.

36 MATERIALS SCIENCE↗

Selective laser melting of 304L stainless steel: Role of volumetric energy density on the microstructure, texture and mechanical properties

The role of volumetric energy density on the microstructural evolution, texture and mechanical properties of 304L stainless steel parts additively manufactured via selective laser melting process is investigated. 304L is chosen because it is a potential candidate to be used as a matrix in a metal matrix composite with nanoparticles dispersion for energy and high temperature applications. The highest relative density of 99 %±0.5 was achieved using a volumetric energy density of 1400 J/mm 3 . Both XRD analysis and Scheil simulation revealed the presence of a small trace of the delta ferrite phase, due to rapid solidification within the austenitic matrix of 304L. Here, a fine cellular substructure ranged between 0.4–1.8 μm, was detected across different energy density values. At the highest energy density value, a strong texture in the direction of [100] was identified. At lower energy density values, multicomponent texture was found due to high nucleation rate and the existing defects. Yield strength, ultimate tensile strength, and microhardness of samples with a relative density of 99 % were measured to be 540 ± 15 MPa, 660 ± 20 MPa and 254 ± 7 HV, respectively and higher than mechanical properties of conventionally manufactured 304L stainless steel. Heat treatment of the laser melted 304L at 1200 °C for 2 h, resulted in the nucleation of recrystallized equiaxed grains followed by a decrease in microhardness value from 233 ± 3 HV to 208 ± 8 HV due to disappearance of cellular substructure.

304L stainless steel↗

Microstructural evaluation of thin-wall sections of 316L stainless steel produced by laser powder-bed fusion processing

The synthesis of thin wall sections that are only 0.4 mm thick is achieved with LPBF AM. Sample preparation is optimized using metallographic polishing to produce samples with only 0.3 um rms roughness for scanning electron microanalysis with EBSD and EDS. A fully austenitic 316L phase is found without evidence of secondary phases. Unlike some AM products that can readily evidence composition segregation due to solute rejection as attributable to temperature gradients within the solidification

Jankowski, Alan F. [Sandia National Laboratories (↗

Controlling the extent of atomic ordering in intermetallic alloys through additive manufacturing

Control of the atomic structure, as measured by the extent of the embrittling B2 chemically ordered phase, is demonstrated in intermetallic alloys through additive manufacturing (AM) and characterized using high fidelity neutron diffraction. As a layer-by-layer rapid solidification process, AM was employed to suppress the extent of chemically ordered B2 phases in a soft ferromagnetic Fe-Co alloy, as a model material system of interest to electromagnetic applications. The extent of atomic ordering was found to be insensitive to the spatial location within specimens and insinuates that the thermal conditions within only a few AM layers were most influential in controlling the microstructure, in agreement with the predictions from a thermal model for welding. Analysis of process parameter effects on ordering found that suppression of B2 phase was the result of an increased average cooling rate during processing. AM processing parameters, namely interlayer interval time and build velocity, were used to systematically control the relative fraction of ordered B2 phase in specimens from 0.49 to 0.72. Hardness of AM specimens was more than 150% higher than conventionally processed bulk material. Implications for tailoring microstructures of intermetallic alloys are discussed.

36 MATERIALS SCIENCE↗

Robust Solar Receivers Using MAX Phase Materials

This work was supported by the U.S. Department of Energy’s Office of Energy Efficiency and Renewable Energy under the Solar Energy Technologies Office Award Number 35928. The objective of the proposed effort was to develop and optimize additive manufacturing technologies for low-cost fabrication of high-temperature receivers using MAX phase-based materials (Ti 3 SiC 2 and Ti 3 AlC 2 ). MAX phase materials are a group of ternary metal carbides and nitrides where M stands for an early transition metal element, A is a group 13–16 element, and X is C and/or N. In Phase 1, the binder jetting additive manufacturing process was used to synthesize and characterize the Ti 3 SiC 2 MAX phase material. The typical process involved first producing a TiC preform using binder jetting followed by infiltration of the preform with silicon melt to form Ti 3 SiC 2 in situ. The reaction-infiltrated samples showed formation of MAX phase in the sample core; however, the surface showed cracking. Various process conditions—cooling rates, hold times, Si proportion, etc.—were varied to minimize the surface cracking. The fabricated MAX phase core was characterized by microstructure analysis and evaluations of mechanical properties such as hardness and thermal shock. In Phase 2, the focus included fabrication of Ti 3 SiC 2 MAX phase materials by spark plasma sintering (SPS) and synthesis of Ti 3 AlC 2 MAX phase materials by the Al melt infiltration process. It is expected that Al infiltration will not cause sample cracking, since Al does not expand during solidification. In addition, other processing approaches were investigated to fabricate the MAX phase materials, such as SPS with a graphite bedding approach for producing short-length Ti 3 AlC 2 MAX phase tubes for demonstration of prototypical Concentrating Solar Power receiver tubes. Fabricated samples underwent thermo-mechanical testing to validate the materials for the solar receiver application at temperatures >1000°C. In Phase 3, the effort focused on the development and optimization of the Ti-Al-C MAX phase composite material using the Al melt infiltration approach. We started with optimization of precursor powders and making preform structures by either pressing them in a die or using the binder jetting additive manufacturing process followed by Al melt infiltration. In addition, we investigated the formation of preform structures by cold isostatic pressing followed by Al melt infiltration for making Ti-Al-C MAX phase composite. Thermo-mechanical characterizations, such as creep, strength, and thermal shock, were conducted to establish the structures’ performance.

36 MATERIALS SCIENCE↗

Microstructure and creep properties of cast near-eutectic Al–Ce–Ni alloys

This study investigates the as-cast and aged microstructures, thermal stability, ambient temperature strengthening, and creep resistance of three ternary Al–Ce–Ni alloys (wt%): near-eutectic Al–10Ce–5Ni (with both eutectic and hypoeutectic regions), hypoeutectic Al-7.5Ce-3.75Ni (with numerous primary Al dendrites), and hypereutectic Al-12.5Ce-6.25Ni (with coarse, blocky primary Al3Ni and Al11Ce3 precipitates and some primary Al dendrites). Depending on the alloy composition and local solidification conditions, the following eutectic morphologies are found: (i) coarse Al–Ce eutectic colonies where Al 11 Ce 3 is in the form of “Chinese script”, (ii) intermingled regions of binary Al–Ce and Al–Ni eutectic colonies, with finer Al 3 Ni and Al 11 Ce 3 fibers, (iii) large ternary eutectic colonies, where the binary Al 3 Ni and Al 11 Ce 3 phases are alternating or intertwining within the individual, fine fibers (diameters of ~60–170 nm, depending on solidification rates), and (iv) ternary eutectic zones (between primary Al dendrites), where fine Al 3 Ni and Al 11 Ce 3 build up a 3D-interconnected network. The high volume fraction of intermetallic phases and extremely fine eutectic spacing/fiber diameter both contribute to high ambient strengthening (higher as-cast microhardness than binary Al–Ce or Al–Ni), and also provide enhanced creep resistance at 300 and 350 °C. Additionally, the alloys are coarsening-resistant up to 425 °C for extended periods, with a gradual decrease in microhardness. The alloys aged at 400 °C to 1050 h show fiber fragmentation and coarsening of the resulting particles, with the faster-diffusing Ni driving more rapid coarsening of the Al 3 Ni particles which engulf finer, more stable Al 11 Ce 3 particles. Severe overaging (performed at 590 °C for 24 h) leads to Al 3 Ni and Al 11 Ce 3 spheroids which remain submicron-sized in eutectic colonies, but micron-sized at colony boundary and at Al dendrite-eutectic interface. Creep resistance at 300 °C of overaged Al–10Ce–5Ni remains substantial, consistent with load-transfer based composite strengthening being an important strengthening mechanism in these alloys, making them excellent candidates for replacement of heavier steel or titanium parts operating under stress up to 300 °C.

36 MATERIALS SCIENCE↗