Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Power Performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

CMS HGCAL ECON-D ASIC : Impact of CMOS fabrication process tuning on performance and radiation tolerance

The CMS experiment’s High Granularity Calorimeter (HGCAL) upgrade will replace CMS’s existing endcap calorimeters in preparation for the High Luminosity LHC. To effectively use over 6 million channels of this “imaging”calorimeter, CMS has developed two novel Endcap Concentrator (ECON) ASICs to perform data compression/selection on detector. The ECON-D ASIC operates on the 750kHz data path, and the ECON-T ASIC on the 40MHz trigger path. These 65 nm CMOS ASICs are radiation tolerant to 200 Mrad and low power, operating at less than 2.5 mW/channel. The first full-functionality prototype ECONs were produced and characterized in 2021-23, and an initial engineering run was performed in 2024. ECON-D radiation testing for the engineering run revealed that the chip’s internal SRAMs produce intermittent read errors for a non-negligible fraction of chips. Further investigation indicated that the SRAM performance is highly sensitive to the exact parameters of the CMOS fabrication process. To both study this process sensitivity and mitigate SRAM performance issues, twenty ECON wafers were produced in 2025 with a range of doping concentrations designed to tune the underlying transistor threshold voltage by 0%, 5%, 10%, and 15% from nominal. This talk will present first measurements of ECON-D performance, power consumption, and radiation tolerance for these four variations of CMOS process.

Syal, Chinar [Fermilab]↗
DOE OSTI2022

Effective Selective Area Doping for GaN Vertical Power Transistors Enabled by Innovative Materials Engineering

GaN vertical power transistors have emerged as promising candidates for future high efficiency high power electronic applications, with the potential to outperform conventional GaN lateral power devices in terms of power, breakdown, and avalanche characteristics. However, the development of current GaN vertical power transistors is seriously hindered by the poor materials performance of selective area doped p-n junctions. A mechanistic understanding of these fundamental materials issues is essential in order to achieve high performance selective area doped p-n junctions and consequently to advance the GaN vertical power transistor technology. To address this challenge, we carried out a comprehensive research program that advance fundamental knowledge in the selective area doping for GaN materials, and which will lead to the development of high performance GaN vertical power transistors. First, we developed innovative fabrication processes, including novel surface etching, surface passivation, and metalorganic chemical vapor deposition (MOCVD) growth, which provided enhanced opportunities for solving the unique challenges of selective area doping in GaN materials. Second, we performed a fundamental materials study using powerful characterization methods including transmission electron microscopy (TEM), ultraviolet (UV-), x-ray and angle-resolved photoelectron spectroscopy (UPS/XPS/ARPES), electron holography, and cathodoluminescence (CL); Third, we investigated several related issues, including Mg incorporation, polarization effects in carrier transport, and non-ideal material effects, which have rarely been explored so far. At the end of this project, we successfully demonstrated (1) fundamental understanding of selective area etching, regrowth, and doping of GaN, and associated knowledge on defects, interface, and breakdown properties. (2) Effective etch and regrowth processing recipes to achieve etch/regrowth GaN p-n diodes with very low leakage of 3.5 nA at 600 V, which meets the ARPA-E target. (2) High performance vertical GaN p-n didoes and vertical junction termination extension (JTE) devices with breakdown voltage of ~ 2 kV, and breakdown electric field of ~ 3.5 MV/cm, which are close to the performance limit of GaN. The successful outcome has resulted in new fundamental understandings in the selective area doping and regrowth process for GaN, which will lead to groundbreaking GaN vertical transistors for high performance next generation power electronics.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2026

Design and Performance Assessment of Intermediary Coils for Misalignment Tolerance Improvement in Wireless Power Transfer Systems

This paper investigates the use of intermediate coils positioned between the primary and secondary coils in Wireless Power Transfer (WPT) systems for electric vehicle (EV) charging, with the objective of improving power transfer efficiency and robustness under misalignment conditions. An optimized 1 kW power system that operates at 85 kHz is developed and the misalignment performance was analyzed and compared with and without intermediate coils. A preliminary increase in efficiency of 2.3% at a misalignment of 52% of the coil radius is shown to be possible for a passive intermediate coil. An experimental prototype is built for design verification.

Sivka, Gozde [ORNL]↗
DOE OSTI2024

CMB-S4: Iterative Internal Delensing and r Constraints

Abstract The tightest constraints on the tensor-to-scalar ratio r can only be obtained after removing a substantial fraction of the lensing B -mode sample variance. The planned Cosmic Microwave Background (CMB)-S4 experiment ( cmb-s4.org ) will remove the lensing B -mode signal internally by reconstructing the gravitational lenses from high-resolution observations. We document here a first lensing reconstruction pipeline able to achieve this optimally for arbitrary sky coverage. We make it part of a map-based framework to test CMB-S4 delensing performance and its constraining power on r , including inhomogeneous noise and two non-Gaussian Galactic polarized foreground models. The framework performs component separation of the high-resolution maps, followed by the construction of lensing B -mode templates, which are then included in a parametric small-aperture map cross-spectra-based likelihood for r . We find that the lensing reconstruction and framework achieve the expected performance, compatible with the target σ ( r ) ≃ 5 · 10 −4 in the absence of a tensor signal, after an effective removal of 92%–93% of the lensing B -mode variance, depending on the simulation set. The code for the lensing reconstruction can also be used for cross-correlation studies with large-scale structures, lensing spectrum reconstruction, cluster lensing, or other CMB lensing-related purposes. As part of our tests, we also demonstrate the joint optimal reconstruction of the lensing potential with the lensing curl potential mode at second order in the density fluctuations.

Astronomy & Astrophysics↗
DOE OSTI2020

Design, Analysis, Comparison, and Experimental Validation of Insulated Metal Substrates for High-Power Wide-Bandgap Power Modules

Direct bonded copper (DBC) substrates used in power modules have limited heat spreading and manufacturing capability due to ceramic properties and manufacturing technology. The ceramic and copper bonding is also subject to high mechanical stress due to coefficient of thermal expansion mismatch between the copper and the ceramic. For wide-bandgap (WBG) devices, it is of interest exploring new substrate technologies that can overcome some of the challenges of direct bonded copper substrates. In this technical paper, the design, analysis, and comparison of insulated metal substrates (IMSs) for high-power wide-bandgap semiconductor-based power modules are discussed. This paper starts with technical description and discussion of state-of-the-art DBC substrates with different ceramic insulators such as aluminum nitride (AlN), Al 2 O 3 , and Si 3 N 4 . Next, an introduction of IMSs and their material properties, and a design approach for SiC (silicon carbide) metal-oxide-semiconductor field-effect transistor (MOSFET)-based power modules for high-power applications is provided. The influence of dielectric thickness on the power handling capability of the substrate are also discussed. The designed IMS and DBC substrates were characterized in terms of steady-state and transient thermal performance using finite element simulation. Finally, the performance of the IMS and DBC are validated in an experimental setup under different loading and cooling temperature conditions. We report the simulation and experimental results showed that the IMS can provide high steady-state thermal performance for high-power modules based on SiC MOSFETs. Furthermore, the IMS provided enhanced transient thermal performance, which provided a reduced junction temperature when the module is operated at low fundamental output frequencies in traction drive systems.

42 ENGINEERING↗
DOE OSTI2021

Highly Integrated Wide Bandgap Power Module for Next Generation Plug-In Vehicles (Final Report)

Wide bandgap devices are key enablers for high power density traction inverters. A highly integrated wide bandgap (WBG) power module enables higher temperature operation, higher inverter efficiency and overall smaller die area with the same power delivery. However, it requires careful design of the power module to take advantage of all the superior material properties that silicon carbide (SiC) provides over conventional silicon (Si) Insulated Gate Bipolar Transistor (IGBT) based design. This project developed an efficient and densely packed SiC power module for an automotive traction inverter application. Extensive study was performed to select the best performing SiC die considering a wide range of temperature variation, suitability to integrate into target packaging, robust body diode performance and overall high electrical efficiency. Multiple design ideas were explored to achieve lower stray inductance for both power loop and signal loop, uniform current distribution, compact form factor, and very high thermal performance. The final power module package includes all six inverter switches in the same module (six-pack) with die sintered at both bottom and top surfaces utilizing high performance substrate to achieve high electrical and thermal performance. Two power module variants were developed using 900 V and 1200 V devices for operating at two different high voltage levels (> 600 V HV battery). Both power modules were comprehensively characterized, and high efficiency operation of the inverter was confirmed through analysis. Finally, a complete functional inverter was built with the 1200V power modules using other essential components (HV capacitors, gate driver board, controller board, current sensor, connectors etc.) and tested using GM’s standard test procedure. There are several challenges associated with adopting WBG devices for high voltage operation. In order to assess and mitigate those challenges, GM and subrecipients of this project have conducted multiple detailed studies. This includes phase current reconstruction using integrated Rogowski coil, device junction temperature estimation using on-state gate resistance, modeling and testing the effect of high voltage and fast switching on motor insulation and bearings, partial discharge inception voltage measurement under different environmental conditions. Findings of all these studies are summarized in this report.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2023

Opening the Bandgap of Metallic Half-Heuslers via the Introduction of d–d Orbital Interactions

Half-Heusler compounds with semiconducting behavior have been developed as high-performance thermoelectric materials for power generation. Many half-Heusler compounds also exhibit metallic behavior without a bandgap and thus inferior thermoelectric performance. Here, taking metallic half-Heusler MgNiSb as an example, a bandgap opening strategy is proposed by introducing the d–d orbital interactions, which enables the opening of the bandgap and the improvement of the thermoelectric performance. The width of the bandgap can be engineered by tuning the strength of the d–d orbital interactions. The conduction type and the carrier density can also be modulated in the Mg 1- x Ti x NiSb system. Both improved n-type and p-type thermoelectric properties are realized, which are much higher than that of the metallic MgNiSb. The proposed bandgap opening strategy can be employed to design and develop new half-Heusler semiconductors for functional and energy applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Improvement of Coal Power Plant Dry Cooling Technology through Application of Cold Thermal Energy Storage

The U.S. power infrastructure is currently heavily reliant on water cooling. The power plants in the U.S. account for approximately 40% of freshwater withdrawals, with 90% of it used in condenser cooling. The most used cooling technology in coal-fired power plants is a once-through condenser; however, this cooling method requires high water withdrawal rates and results in thermal pollution of the water source. Wet WCTs offer an alternative to once-through condensers due to much lower water withdrawals. However, these systems suffer from water consumption through evaporation making them undesirable options in areas subject to droughts and in arid areas. The direct dry cooled condensers (ACCs) and dry cooling towers (DCT) account for 1.8%, hybrid cooling (ACC + WCT) accounts for 0.5%, while other cooling technologies represent the rest (0.7%). The ACC/DCTs represent an attractive alternative for power plants; however, this technology has not been widely adopted in the US (less than 2% of power plants) due to its negative impact on plant performance. As a rule of thumb, dry cooling results in performance penalty equivalent to approximately 2%-point efficiency loss compared to wet cooling, although the actual magnitude varies with ambient dry bulb temperature, DBT which may vary considerably during the day. As DBT increases, the plant power output decreases, reaching a minimum at the hottest period of the day, which usually coincides with the highest electricity demand for air condition load. Therefore, performance of power plants using DCT/ACC cooling technology is the lowest during the summer mid-day when ambient temperature is the highest. For example, the decrease of the inlet air temperature to the DCT/ACC by 2 Deg C could generate up to 5% additional power at peak demand. It is, therefore, important to improve dry cooling technology to maintain the viability of coal-fired power plants in a carbon constrained future. The method for reducing the cooling air temperature and keeping it constant would mitigate this problem significantly. Objectives of this project were to develop, design, evaluate, and demonstrate a cost-effective system for improving performance of a DCT or ACC for thermal (coal-fired) power plant applications using a low-cost heat storage materials, such as pervious concrete (PC) and phase change material (PCM). Thus, the study focused on development of the system(s) that could be used to alleviate the difficulties in operating DCT/ACC during the summer months by storing cold energy during the nighttime in inexpensive materials PC and PCM and using it during the hottest period(s) of the day. Since very large quantities of cold energy need to be stored to make an impact on performance of a large power plant, it is essential that the storage materials and associated cold energy storage design(s) are inexpensive and the system is simple to build, maintain and operate. To achieve the project objectives, a comprehensive approach, including material development and characterization, component and system modeling, and laboratory- and prototype-scale experiments, was employed including modeling of the system components and of the entire system, development (engineering) of the materials for the heat storage modules of the Cold Thermal Energy Storage System (CTESS) and determination of their properties, design, manufacturing and setup of the laboratory- and prototype-scale test facility and testing, design, manufacturing and setup of the prototype-scale test facility. A modular design of CTESS was employed, where representative modules were designed as the integrated direct contact heat exchanger and thermal energy storage (TES) system. CTESS modules were manufactured and tested. Two prototype-scale designs of the CTESS modules were developed and tested. The use of CTESS increases plant generation increases since it lowers air temperature entering ACC/DCT and keeps it constant during the hottest time of the day. For a PCM-based CTESS, the ambient air temperature is lowered close to the PCM phase change temperature. The duration of the cooling effect depends on the latent heat and mass of PCM in the CTESS. For this project, commercial grade CaCl2 hexahydrate (CaCl2·6H2O or CC6) PCM with phase change temperature of 25 Deg. C was used due to its low cost. For practical reasons, the CTESS was designed to maintain the cooling effect for four hours. The low phase change temperature associated with the commercial grade PCM used in CTESS results in considerably higher improvement in net generation compared to the laboratory (pure) grade. The resistance to heat transfer results in lower net generation compared to the ideal case where resistance to heat transfer is zero. The results demonstrate that CTESS is effective in improving the performance of a dry cooling system. However, its effectiveness depends on the relationship between the ambient air conditions and PCM phase change temperature. As is the case with the heat rejection system, for the best performance, the PCM used in CTESS would need to be matched to the ambient air conditions. The results obtained in this report for selected geographical locations are valid for CC6 and demonstrate that the level of performance to be achieved by the technology will be location-dependent, as is the case with the air cooled condensers. The methodology for engineering of PC-PCM-based heat storage medium is applicable to other PCMs that may need to be used for other ambient air conditions and geographical locations.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2025

Rotated-Droop Control for Enhanced Stability and Power Decoupling in Microgrids With Complex Line Impedances

Classical droop control in microgrids predominantly assumes inductive line impedance, which simplifies implementation but causes power coupling and steady-state errors in systems with resistive and inductive lines. This paper proposes a rotated-droop control strategy for grid-forming inverters that reformulates the power equations by incorporating the magnitude and angle of the line impedance within a rotated reference frame. This method enhances the decoupling of active and reactive power dynamics without increasing complexity or requiring communication links. A small-signal state-space model was created to capture the dynamic behavior of the system under varying impedance parameters, preserving the original droop gains by rotating the power control structure. This allows eigenvalue-based stability analysis and enhances damping and transient performance. Simulation and experimental results validated the improved power-sharing performance, faster response, and robustness of the proposed method under different impedance conditions. This approach maintains the decentralized structure of the conventional droop control while enabling greater adaptability and scalability, making it suitable for modern inverter-based microgrids with dynamic topologies.

Campo-Ossa, Daniel Dario [Univ. of Puerto Rico, Ag↗
DOE OSTI2024

Cyclable Variable Path Length Multilevel Structures for Lossless Ion Manipulations (SLIM) Platform for Enhanced Ion Mobility Separations

Ion mobility-mass spectrometry (IMS-MS) is increasingly used to analyze complex samples and provide structural information of unknown compounds. As the complexity of samples increases, there is a need to improve the resolution of IMS-MS instruments to increase the rate of molecular identification. In this work, we evaluated a cyclable and variable-pathlength multilevel Structures for Lossless Ion Manipulations (SLIM) platform to achieve a higher resolving power than previously possible. This new multilevel SLIM platform has eight separation levels connected by ion escalators and a path length of ~88 meters (~11 meters per level). Our new multilevel SLIM can also be operated in an ‘ion cycling’ mode where a set of return ion escalators transport ions from the eighth back to the first level, allowing even longer path lengths (and higher IMS resolution). The platform has been improved to enhance the ion transmission and IMS separation quality by reducing the spacing between SLIM boards as well as board thickness, reducing the ions’ escalator residence time. Compared to the previous generation, the new multilevel SLIM demonstrated a better transmission for a set of phosphazene ions, especially for the low-mobility ions. The new multilevel SLIM achieved better resolving powers than our previous 4-level SLIM. The collision cross-section-based resolving power of the SLIM platform was tested using a pair of singly-charged reverse sequence peptides (SDGRG 1+ , GRGDS 1+ ). We achieved 1100 resolving power using 88 meters of path length (i.e., 8 levels) and 1400 following an additional pass through the eight levels (i.e., 16 levels or 173.5 m). The multilevel SLIM was further evaluated to demonstrate the enhanced separation for a positively and negatively charged brain total lipid extract sample. Finally, the new multilevel SLIM enables much higher resolving powers for a wide range of ion mobilities, improved transmission for low-mobility ions, and the ability to perform even higher resolving power for ions of interest.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Post-Irradiation Examination on MiniFuel UCO and UO 2 TRISO Particles Irradiated in HFIR at High Power

Post-irradiation examination (PIE) of MiniFuel compacts was conducted at Oak Ridge National Laboratory (ORNL) under the Nuclear Science User Facilities project in collaboration with Kairos Power (KP) to evaluate the performance of tristructural-isotropic (TRISO) particles under high particle power and fluoride-salt-cooled high-temperature reactor (FHR)-relevant conditions. MiniFuel compacts containing low-enriched uranium oxide-uranium carbide (LEUCO), low-enriched uranium dioxide (LEUO2), and natural UCO (NUCO) kernels were irradiated for four cycles at ORNL’s High Flux Isotope Reactor (HFIR) at target temperatures between 500°C and 900°C. Post irradiation, the experiment was disassembled at ORNL to recover the MiniFuel subcapsules, which were subsequently punctured to measure fission gas release. Subcapsule disassembly allowed the recovery of components of interest, such as silicon carbide (SiC) thermometry, fuel specimens, fission product sinks, and SiC spacers. The experimental irradiation temperature was confirmed by analyzing the SiC thermometry via dilatometry. PIE on the fuel specimens included gamma spectrometry and deconsolidation leach burn leach, which were complemented by imaging techniques such as x-ray computed tomography, optical microscopy, and electron microscopy. The PIE results provide insight into TRISO particle integrity, fission product retention, coating performance, and kernel migration, informing fuel qualification for application in KP’s FHR concept.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Post-Irradiation Examination on MiniFuel UCO and UO 2 TRISO Particles Irradiated in HFIR at High Power

Post-irradiation examination (PIE) of MiniFuel compacts was conducted at Oak Ridge National Laboratory (ORNL) under the Nuclear Science User Facilities project in collaboration with Kairos Power (KP) to evaluate the performance of tristructural-isotropic (TRISO) particles under high particle power and fluoride-salt-cooled high-temperature reactor (FHR)-relevant conditions. MiniFuel compacts containing low-enriched uranium oxide-uranium carbide (LEUCO), low-enriched uranium dioxide (LEUO 2 ), and natural UCO (NUCO) kernels were irradiated for four cycles at ORNL’s High Flux Isotope Reactor (HFIR) at target temperatures between 500°C and 900°C. Post irradiation, the experiment was disassembled at ORNL to recover the MiniFuel subcapsules, which were subsequently punctured to measure fission gas release. Subcapsule disassembly allowed the recovery of components of interest, such as silicon carbide (SiC) thermometry, fuel specimens, fission product sinks, and SiC spacers. The experimental irradiation temperature was confirmed by analyzing the SiC thermometry via dilatometry. PIE on the fuel specimens included gamma spectrometry and deconsolidation leach burn leach, which were complemented by imaging techniques such as x-ray computed tomography, optical microscopy, and electron microscopy. The PIE results provide insight into TRISO particle integrity, fission product retention, coating performance, and kernel migration, informing fuel qualification for application in KP’s FHR concept.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Potassium carbonate decomposition modeling within rotating detonation engines for direct power extraction applications

We report that recently, there has been a significant interest in detonation-based combustion systems, such as rotating detonation engines (RDE), due to potential performance advantages in propulsion and energy applications. This includes improvements in thermodynamic efficiency, inherently high gas velocities, and the possibility of achieving an increase in total pressure (i.e. pressure gain) through the combustion process. Due to approximating a constant volume combustion process, these devices also tend to exhibit extremely high local gas temperatures relative to a comparable constant pressure combustor. These advantages overlap well with desirable performance characteristics of direct power extraction (DPE) technologies, such as a magnetohydrodynamic (MHD) generator. Typically, in DPE systems hot combustion products are seeded with an easily ionizable material such as potassium carbonate (K 2 CO 3 ) in order to boost the electrical conductivity. However, due to the short gas residence times within an RDE, it was unclear whether forming an electrically conductive combustion plasma would be feasible for integration with a downstream MHD generator. A model is presented which describes the heating, decomposition, and ionization of solid K 2 CO 3 particles and aqueous solutions of K 2 CO 3 in water, for a given initial particle diameter. This model was combined with available computational fluid dynamics (CFD) data for an oxygen-methane RDE in a one-way coupled Eulerian-Lagrangian framework to predict particle trajectories and the corresponding heating, decomposition, and ionization histories. Electrical conductivities were computed using a previously developed model, and a method was proposed to determine an equivalent average electrical conductivity. Results show that particle sizes below ~30 µm are able to fully decompose before reaching the exit of the RDE. While the one-way coupled nature of the simulations precluded rigorous evaluation of the effects of seed material on detonability, a substantial temperature reduction is expected at the detonation wave front due to heating and decomposition. A preliminary comparison is presented between the RDE and an equivalent constant pressure adiabatic combustor, showing a potential performance advantage for the RDE.

42 ENGINEERING↗
DOE OSTI2025

Stabilization of high-performance rock-salt LiMnSbTe3 thermoelectrics with embedded van der Waals-like gaps

Rock-salt-structured compounds like lead chalcogenides are promising thermoelectrics, as their high symmetry, strong anharmonicity, and favorable phase behavior collectively lead to high performance by enabling large power factors and ultralow thermal conductivity. Here, we report LiMnSbTe 3 , a new rock-salt semiconductor stabilized through targeted chemical design by combining hexagonal MnTe with cubic LiSbTe 2 . Embedded in the highsymmetry matrix, van der Waals-like gaps form due to Sb 2 Te 3 nanoscale segregation, which acts as effective phonon-scattering centers, leading to a low lattice thermal conductivity of 0.37Wm- 1 K -1 at 873 K with alloy scattering from disordered cations. The ordered local structure of Sb2Te 3 -type vdW-like gaps and the cross-gap interaction facilitate the carrier transport. Aided by energyconverged valence bands and a paramagnon drag effect, high Seebeck coefficients and enhanced power factor can be achieved, leading to a high ZT of 1.2 at 873 K. Furthermore, introducing Mn deficiency increases ZT to 1.5, highlighting the potential for higher performance through optimized doping or alloying. A segmented single-leg thermoelectric module achieves an output power density of 0.52 Wcm -2 and an efficiency of 8.7% under ΔT of 478 K, further demonstrating its promising thermoelectric applications.

42 ENGINEERING↗
DOE OSTI2023

Integrating Learning and Physics based Computation for Fast Online Transient Analysis

In this work, a novel method that integrates learning and physics based computation is developed for greatly accelerating the simulation of full power system transient trajectories. To solve the dynamic algebraic equations, the method replaces the time-consuming dynamic computation for generator dynamics with trained predictors, while retaining the time-efficient algebraic computation of solving AC-power flow (PF) for power systems. In particular, a predictor is trained for each generator, and the system trajectories are computed by alternating steps of calling the predictors and solving AC-PF. The proposed method also allows fully parallelizable training strategies and a flexible trade-off between training time and testing accuracy. Comprehensive evaluations of the proposed method for transient/dynamic contingency analysis of the New York/New England 16-machine 68-bus power systems demonstrate excellent performance and significant acceleration of computation.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2022

Comparative Investigation of Current-Source Inverters using SiC Discrete Devices and Power Modules

The purpose of this paper is to investigate the impact of the SiC device packages on the commutation performance characteristics of current-source inverters (CSIs). The parasitic components in the CSI current commutation loop between the two-phase legs and output capacitors have a significant impact on the high-frequency performance of the SiC devices. To meet the elevated current requirements of high-power CSIs, it is often necessary to connect multiple discrete devices in parallel which increases the current commutation loop length. The selection of compact high-power SiC MOSFET and Schottky diode modules instead of discrete devices can be highly desirable to reduce the loop inductance and improve the system performance and power density. Two CSI benchtop prototype units, one with SiC discrete devices and the other with power modules, have been designed and tested, and the performances of the two CSIs are compared. The CSI with SiC power modules significantly reduces the inverter volume and lowers the parasitic inductance by 60% and the voltage ripple amplitude by 20% compared to the CSI unit with discrete devices.

42 ENGINEERING↗
DOE OSTI2023

Medium-temperature phase change material integration in domestic heat pump water heaters for improved thermal energy storage

In this review, we examine state-of-the-art developments in integrating phase change materials (PCMs) for thermal energy storage (TES) in domestic heat pump water heaters (HPWHs). The component design optimization and control optimization of HPWHs and TES are reviewed for insight into improving the thermal capacity and efficiency of a PCM-integrated HPWH. The state-of-the-art review is categorized by the stage of development of the PCM for deployment in HPWHs. To select appropriate PCMs for HPWHs, a six-factor down-selection process is used to determine the best material(s) for integration in HPWHs with appropriate heat exchanger design. Ultimately, food-grade PCMs appear to be the best candidate for integration of TES in domestic HPWHs because they are nontoxic, highly cyclable, and have heat transfer properties accommodable to water heating when integrated in a manner to overcome the thermal conductivity limitations of the material. A key parameter of water heating performance is thermal heating power of the PCM component, which is not often reported. Many studies report significant improvement in capacity and efficiency. Furthermore, many performance metrics are identified from the literature to quantify the system performance, but agreement across studies is not found. Unified energy factor and first hour rating performance tests are required for commercially available HPWHs, and these performance metrics could homogenize the literature. Ultimately, we find that select PCMs are ready for deployment with HPWHs for performance improvement, and component design and control optimizations are new avenues of research and development required for a commercially viable PCM-integrated HPWH system.

25 ENERGY STORAGE↗
DOE OSTI2026

Optimisation of the Kaplan hydropower system via PID 2 and digital twin

Here, this paper proposes a proportional–integral-double–derivative (PID 2 ) optimisation method for the Kaplan hydropower system by building a digital twin. The study first uses one multilayer perceptron (MLP) to model the hydroturbine dynamic and then adopts three connected MLPs to model the generator dynamic, both in an open-loop fashion. Inspired by stochastic distribution control (SDC) theory, we regard the training of the turbine's neural network model as a process control problem, and we propose minimising entropy loss to update the network parameters. The next step is to build the digital twin by connecting the neural network models with a PID 2 controller and a lead-lag exciter and run the whole model in a closed-loop fashion. After that, a binary search approach is applied to optimise the PID 2 parameters based on the obtained digital twin model. The simulation results show that the proposed method can reduce the mean square tracking error by more than 90%. Furthermore, the method is extended to jointly optimise the PID 2 controller and excitation system gains through multiobjective optimisation, leveraging Pareto frontier analysis to balance active power and voltage tracking performance. Simulation results confirm the effectiveness of the proposed method, achieving a 83.46% reduction in relative mean square error of active power, a 47.13% reduction in terminal voltage tracking error, and an 82.78% improvement in the overall scalarized objective.

Hydropower system↗