Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PHASE STUDIES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

Features of the conductivity of the quasi-one-dimensional compound TiS{sub 3}

The structure and transport properties of single crystal whiskers of the TiS{sub 3} quasi-one-dimensional semiconductor have been investigated. The anisotropy of the conductivity in the plane of layers (ab) has been measured as a function of the temperature. The anisotropy at 300 K is 5 and increases with a decrease in the temperature. Features on the temperature dependences of the conductivity along and across the chains are observed at 59 and 17 K. Near the same temperatures the form of the current-voltage characteristics measured along the chains is qualitatively changed. The current-voltage characteristics below 60 K exhibit nonlinearity and have a threshold form below 10 K. The results indicate possible phase transitions and the collective conduction mechanism at low temperatures.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

On the state of hydrogen arising during its melting at megabar pressures

A model of quantum conducting liquid, which arises during melting of molecular hydrogen crystal under megabar pressures, is proposed. This model explains the melting of anomalous type, which was recently experimentally found. The model is based on the cell approximation, which takes into account the contribution of bound states. It is shown that this liquid can be in the metastable state with a density of about 2.3 g/cm{sup 3} and may remain in this state after removing pressure.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Liquid-glass transition as the freezing of characteristic acoustic frequencies

Half-quantum interpretation is proposed for the liquid-glass transition as the freezing of characteristic acoustic frequencies (degrees of freedom) that are related to the molecular mobility of delocalized excited kinetic units, namely, linear quantum oscillators. There exists a correlation between the energy quantum of an elementary excitation (atom delocalization energy) and the glass transition temperature, which is proportional to the characteristic Einstein temperature. By analogy with the Einstein theory of the heat capacity of solids, the temperature range of the concentration of excited atoms in an amorphous medium is divided into the following two regions: a high-temperature region with a linear temperature dependence of this concentration and a low-temperature region, where the concentration of excited atoms decreases exponentially to the limiting minimum value (about 3%). At this value, the viscosity increases to a critical value (about 10{sup 12} Pa s), which corresponds to the glass transition temperature, i.e., the temperature of freezing the mobility of excited kinetic units. The temperature dependence of the free activation energy of viscous flow in the glass transition range is specified by the temperature dependence of the relative number of excited atoms.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Laws of formation of polar smectic phases under a frustrated interaction

The Landau theory of phase transitions with a two-component order parameter is used to systematically calculate the structures and phase diagrams of polar liquid crystals. Commensurate and incommensurate structures with a layer-type period form as a result of a frustration interaction. Phase diagrams are calculated when various short- and long-range interlayer interactions are sequentially introduced. As a result, the nature of formation of various structures is revealed. The calculated phase diagrams explain the formation of various phases, their temperature sequence (including so-called 'unusual' sequence of phases), and the nature of forces responsible for the formation of a certain structure and the shape of a phase diagram.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Materials data science using CRADLE: A distributed, data-centric approach

Abstract There is a paradigm shift towards data-centric AI, where model efficacy relies on quality, unified data. The common research analytics and data lifecycle environment (CRADLE™) is an infrastructure and framework that supports a data-centric paradigm and materials data science at scale through heterogeneous data management, elastic scaling, and accessible interfaces. We demonstrate CRADLE’s capabilities through five materials science studies: phase identification in X-ray diffraction, defect segmentation in X-ray computed tomography, polymer crystallization analysis in atomic force microscopy, feature extraction from additive manufacturing, and geospatial data fusion. CRADLE catalyzes scalable, reproducible insights to transform how data is captured, stored, and analyzed. Graphical abstract

97 MATHEMATICS AND COMPUTING↗

Merging high resolution geophysical and geochemical surveys to reduce exploration risk at glass buttes, Oregon

The engineering and studies phase of the Glass Buttes project was aimed at reducing risk during the early stages of geothermal project development. The project’s inclusion of high resolution geophysical and geochemical surveys allowed Ormat to evaluate the value of these surveys both independently and in combination to quantify the most valuable course of action for exploration in an area where structure, permeability, and temperature are the most pressing questions. The sizes of the thermal anomalies at Glass Buttes are unusually large. Over the course of Phase I Ormat acquired high resolution LIDAR data to accurately map fault manifestations at the surface and collected detailed gravity and aeromagnetic surveys to map subsurface structural features. In addition, Ormat collected airborne hyperspectral data to assist with mapping the rock petrology and mineral alteration assemblages along Glass Buttes faults and magnetotelluric (MT) survey to try to better constrain the structures at depth. Direct and indirect identification of alteration assemblages reveal not only the geochemical character and temperature of the causative hydrothermal fluids but can also constrain areas of upflow along specific fault segments. All five datasets were merged along with subsurface lithologies and temperatures to predict the most likely locations for high permeability and hot fluids. The Glass Buttes temperature anomalies include 2 areas, totaling 60 km2 (23 mi2) of measured temperature gradients over 165° C/km (10° F/100ft). The Midnight Point temperature anomaly includes the Strat-1 well with 90°C (194 °F) at 603 m (1981 ft) with a 164 °C/km (10°F/100ft) temperature gradient at bottom hole and the GB-18 well with 71°C (160 °F) at 396 m (1300 ft) with a 182°C/km (11°F/100ft) gradient. The primary area of alteration and elevated temperature occurs near major fault intersections associated with Brothers Fault Zone and Basin and Range systems. Evidence for faulting is observed in each data set as follows. Field observations include fault plane orientations, complicated fault intersections, and hydrothermal alteration apparently pre-dating basalt flows. Geophysical anomalies include large, linear gradients in gravity and aeromagnetic data with magnetic lows possibly associated with alteration. Resistivity low anomalies also appear to have offsets associated with faulting. Hyperspectral and XRF identified alteration and individual volcanic flow units, respectively. When incorporated into a 3D geologic model, the fault intersections near the highest proven temperature and geophysical anomalies provide the first priority targets at Midnight Point. Ormat geologists selected the Midnight Point 52-33 drilling target based on a combination of pre-existing drilling data, geologic field work, geophysical interpretation, and geochemical analysis. Deep temperatures of well 52-33 was lower than anticipated. Temperature gradients in the well mirrored those found in historical drilling, but they decreased below 1500 ft and were isothermal below 2000 ft.

15 GEOTHERMAL ENERGY↗

Final Scientific Report: DE-SC0002194

We provide the final scientific report for DE-SC0002194. During the term of this grant, 28 publications spanning a variety of topics were addressed under the rubric of advanced x-ray methods and their application to extreme conditions of time-resolution or x-ray intensities. Notable accomplishments include a new observation of XANES features associated with f-shell reconfiguration in lanthanides, size-dependent x-ray heating effects under XFEL illumination conditions, theoretical development of improved treatments of inelastic x-ray scattering for 'warm dense matter' conditions, and several new instrument develop efforts for atomic, molecular, and condensed phase studies in the lab and at major facility lightsources.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Small-scale pilot plant for gasification of coal and coal/biomass blends and conversion of derived syngas to liquid fuels via Fischer-Tropsch synthesis

This report describes the second phase of a project to design, construct and commission an integrated coal/biomass-to-liquids facility at a capacity of 1 bbl. /day at the University of Kentucky Center for Applied Energy Research (UK-CAER) – specifically for construction, commissioning and operating of the downstream process units for water-gas-shift, Fischer-Tropsch synthesis and balance of plant [BOP]. The deliverables from the operation of this pilot plant is firstly the liquid F-T products and finished fuels which are of interest to UK-CAER’s academic, government and industrial research partners. Going forward the facility will produce research quantities of F-T liquids and finished fuels for subsequent Fuel Quality Testing, Performance and Acceptability. Moreover, the facility is expected to be employed for a range of research and investigations related to: Feed Preparation, Characteristics and Quality; Coal and Biomass Gasification; Gas Clean-up/ Conditioning; Gas Conversion by -F-T Synthesis; Product Work-up and Refining; Systems Analysis and Integration; and Scale-up and Demonstration. Environmental Considerations - particularly how to manage and reduce carbon dioxide emissions from CBTL facilities and from use of the fuels will be a primary research objective. The results of this second phase study include the FEED study and detailed engineering design of the downstream processing units and BOP, the selection of a range of technologies and technology vendors, the as-built plant - its equipment and capabilities, and the results of two trial production runs, one with coal only and one with a coal/biomass blend. These are described in detail in this report.

01 COAL, LIGNITE, AND PEAT↗

Enhancing Clean Energy Innovation Ecosystem Discovery Tool

During March 2016, the DOE’s Office of Energy Policy and Systems Analysis (EPSA) sought a methodology to identify and quantify the strength of the existing clean energy innovation ecosystems (IE) in the U.S. and their characteristics. Oak Ridge National Lab (ORNL) did a pilot study (Phase 1) and demonstrated the feasibility of an application comprised of natural language processing, link analysis, and other computational techniques to transform text and numerical data into metrics on clean energy innovation activity and geography. The data-collection, ingest and analytics pipelines were combined with an advanced user interface, together known as the Ecosystem Discovery Tool, to enhance DOE’s understanding of existing geographic innovation clusters. During Phase 2 of this project, this tool has been further enhanced by integrating new data sets and through backend software architecture changes, validation and bug fixing, making it a much more robust and powerful application. The tool’s user interface is a lot more intuitive, which enables a user to visualize the IE rankings for various geographic regions(CBSA, state level) for different clean energy technologies and seek automated insights. ORNL also created a DOE-specific dashboard that allows the user to visualize and analyze federal funding from various offices including Energy Efficiency and Renewable Energy(EERE), Office of Electricity(OE), Fossil Energy(FE), and Nuclear Energy(NE). During Phase 1 of this project, EPSA defined a clean energy innovation ecosystem as the overlap of five Ecosystem Components: 1) nascent clean energy Indicators, 2) investors, 3) enabling environment, 4) networking assets and 5) large companies. EPSA and ORNL worked together to collect data for each component: 1) small and medium companies, ARPA-E awardees, SBIR awardees, patents, publications, ERCs for Nascent Clean Energy Indicators; 2) qualified investors; 3) the Clean Edge Policy Index/DSIRE for the Enabling Environment; 4) universities, national laboratories, ERCs and incubators for Networking Assets; and 5) large companies and a subset of the Russell 1000 list for Large Companies. The ORNL team created a visual tool based on Tableau that integrated ecosystem component data to score, rank and map IEs. The tool was created with the flexibility to allow the user to choose the weights of each of the five ecosystem components and the subcomponents. This flexibility allows the user to visualize different subsets and to use the underlying data for different types of analysis. During Phase 2 of this project, the backend database and computation process have undergone major changes to provide a much more refined user-interface and added new features into the scoring algorithm. This phase also involved addition of newer databases such as a list of Energy Research Centers (ERC) ,DSIRE, and funding data from EERE, FE, NE, and OE to provide more granular information and more accurate/better quantification.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Sub-Hourly Impacts of High Solar Penetrations in the Western United States: Preprint

This paper presents results of analysis on the sub-hourly impacts of high solar penetrations from the Western Wind and Solar Integration Study Phase 2. Extreme event analysis showed that most large ramps were due to sunrise and sunset events, which have a significant predictability component. Variability in general was much higher in the high-solar versus high-wind scenario. Reserve methodologiesthat had already been developed for wind were therefore modified to take into account the predictability component of solar variability.

14 SOLAR ENERGY↗

Magnetism in nanoparticle LaCoO3

Neutron scattering and magnetometry measurements have been used to study phase transitions in LaCoO3 (LCO). For H <= 100 Oe, evidence for a ferromagnetic (FM) transition is observed at T-c approximate to 87 K. For 1 kOe <= H <= 60 kOe, no transition is apparent. For all H, Curie-Weiss analysis shows predominantly antiferromagnetic (AFM) interactions for T > T-c, but the lack of long-range AFM order indicates magnetic frustration. We argue that the weak ferromagnetism in bulk LCO is induced by lattice strain, as is the case with thin films and nanoparticles. The lattice strain is present at the bulk surfaces and at the interfaces between the LCO and a trace cobalt oxide phase. The ferromagnetic ordering in the LCO bulk is strongly affected by the Co-O-Co angle (gamma), in agreement with recent band calculations which predict that ferromagnetic long-range order can only take place above a critical value, gamma C. Consistent with recent thin film estimations, we find gamma C = 162.8 degrees. For gamma > gamma C, we observe power-law behavior in the structural parameters. gamma decreases with T until the critical temperature, T-o approximate to 37 K; below T-o the rate of change becomes very small. For T < T-o, FM order appears to be confined to regions close to the surfaces, likely due to the lattice strain keeping the local Co-O-Co angle above gamma C.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Comparison of Commercial, State-of-the-Art, Fossil-Based Hydrogen Production Technologies

This presentation provides a deep dive overview of the NETL report publication &quot;Comparison of Commercial, State-of-the-Art, Fossil-Based Hydrogen Production Technologies&quot; released in April 2022. A summary of the study justification, objectives, and approach are presented along with a detailed overview of the major study phases and results.

Lewis, Eric↗

Flexible Gasification of Coal and Biomass to Generate Carbon Free Electric Power and Hydrogen

This paper describes the development of a coal and biomass-fed plant concept to co-produce electric power and hydrogen with net-negative CO2 emissions under the aegis of the 21st Century Power Plant initiative of the U.S. Department of Energy (DOE), whose goal is to advance innovative power plant concepts that are capable of flexible, net-zero carbon emission operations while producing cost-effective “blue” hydrogen to support economy-wide decarbonization goals. The proposed standalone plant will be in Nebraska, USA. The specified design feedstock is a hybrid blend of Powder River Basin (PRB) subbituminous coal from Wyoming and local Nebraska biomass (corn stover), 50 wt.% each (dry basis). Other potential feedstocks, including woody biomass (eastern red cedar) and waste plastic (auto shredder residue) were evaluated or reviewed as alternates. The proposed process block comprises a high-pressure, oxygen-blown fluidized bed gasifier (GTI Energy U-GAS® process) coupled with water gas shift, the Selexol process for acid gas (H2S and CO2) removal, and pressure-swing adsorption (PSA) to yield 8,500 kg/h of high-purity hydrogen. The off gas from the PSA unit is used in the power block (gas turbine combined cycle) to generate electric power to support the gasification process, hydrogen production, and 50 MWe net electric power to the grid. All major plant equipment including the gasifier, gas cleanup system, and power generation are commercially available and proven in other applications and considered at TRL 8-9. However, gasification of corn stover biomass is considered at TRL 6. Overall thermal efficiency of the plant is 50% (net HHV) with net atmospheric CO2 removal at a rate of 250-300,000 tpa. Design activities necessary to provide input to a FEED study (Phase II of the project), including the development of the Environmental Information Volume (EIV) for the host site, and an investment case, based on a pro-forma pre-FEED level cost estimate, have been completed and are described in detail in this paper.

Gülen, S. Can↗

Targeted Health Assessment for Wastes Contained at the Niagara Falls Storage Site to Guide Planning for Remedial Action Alternatives - 13428

The U.S. Army Corps of Engineers (USACE) is evaluating potential remedial alternatives at the 191-acre Niagara Falls Storage Site (NFSS) in Lewiston, New York, under the Formerly Utilized Sites Remedial Action Program (FUSRAP). The Manhattan Engineer District (MED) and Atomic Energy Commission (AEC) brought radioactive wastes to the site during the 1940's and 1950's, and the U.S. Department of Energy (US DOE) consolidated these wastes into a 10-acre interim waste containment structure (IWCS) in the southwest portion of the site during the 1980's. The USACE is evaluating remedial alternatives for radioactive waste contained within the IWCS at the NFSS under the Feasibility Study phase of the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) process. A preliminary evaluation of the IWCS has been conducted to assess potential airborne releases associated with uncovered wastes, particularly during waste excavation, as well as direct exposures to uncovered wastes. Key technical issues for this assessment include: (1) limitations in waste characterization data; (2) representative receptors and exposure routes; (3) estimates of contaminant emissions at an early stage of the evaluation process; (4) consideration of candidate meteorological data and air dispersion modeling approaches; and (5) estimates of health effects from potential exposures to both radionuclides and chemicals that account for recent updates of exposure and toxicity factors. Results of this preliminary health risk assessment indicate if the wastes were uncovered and someone stayed at the IWCS for a number of days to weeks, substantial doses and serious health effects could be incurred. Current controls prevent such exposures, and the controls that would be applied to protect onsite workers during remedial action at the IWCS would also effectively protect the public nearby. This evaluation provides framing context for the upcoming development and detailed evaluation of remedial alternatives for the IWCS. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Overcoming Vicinity Property and Ground Water Challenges at the FUSRAP Middlesex Sampling Plant Project - 17529

The US Army Corps of Engineers (USACE) is addressing the Formerly Utilized Sites Remedial Action Program (FUSRAP) Middlesex Sampling Plant Site (MSP) in accordance with the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA). The MSP has been an active FUSRAP site since the early 1980's and was listed on the National Priority List (NPL) in 1999. Two challenges that the project team are currently addressing are Ground Water (GW) movement through fractured bedrock and Vicinity Properties (VP) assessments. USACE and the US Environmental Protection Agency (USEPA) signed a Record of Decision (ROD) for soils remedial action in 2005 and USACE completed the soils remediation at MSP in 2008, however, VPs were not a part of the soils ROD. Additionally, the State of New Jersey recently identified a potential contaminated VP of the site. VPs are any property in the vicinity of a CERCLA 'facility.' The contaminated VPs of the MSP were addressed prior to the adoption of the CERCLA process to address FUSRAP sites. Since the 1980's many changes to potential Applicable or Relevant and Appropriate Requirements have occurred. As such USACE has begun reassessing the previously addressed VPs for inclusion under the soils ROD as part of the CERCLA process. USACE does expect to have to revisit and potentially remediate up to 12 VPs. This paper will discuss the approach, some challenges, and lessons learned in adequately addressing VPs both from a field work and a post ROD regulatory perspective. USACE is currently in the Feasibility Study phase of the CERCLA process for GW. The project team has encountered and overcome significant challenges with regard to contaminant plume bounding and groundwater movement through the secondary porosity of dipping bedding plane partings and fractured bedrock of the Passaic Aquifer beneath the site. This paper will discuss the challenges, the approaches used, and lessons learned while delineating these contaminants. This paper's discussions are useful for anyone addressing an environmental site with soils contamination on VPs or with delineating contaminants in fractured bedrock. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Robotic D and D: Smart robots - 15093

Project' managers continually seek an ever-greater optimization of time between remote handling operations and those carried out manually; therefore, new technological solutions must be deployed. Robotics offers a great opportunity in this new field of technology to carry out, for example, samplings or remediation in hostile, cluttered surroundings. Teams in charge of dismantling at the CEA have therefore first defined robotizable functions. These functions have been assembled from existing technological blocks to arrive at robots which are operating today [RICAIII, patent: FR 2925702]. Lessons learned, particularly from experience with the RICA robot, have enabled the operating technical specifications to be fine-tuned. A new study phase has been launched applying the same principle of adapting existing, proven means. The growing role of robotics today is unquestioned. Led by research and the academic world; robots such as those equipped with wheels, tracks, feet or even helicopter rotors, are today accessible to the general public, particularly via broadening of the 'open source' concept. Added to these we need tools able to manage large component deconstruction systems, like MAESTRO. Industrialization of such high-potential technological solutions has been aided by: - Easy use, - Increasing reliability, - Flexibility of 'open source' solutions, - Widening skill networks, and therefore greater technical support - Lower costs. Decontamination and dismantling (D and D) projects must be able to meet a number of special demands, increasing the number of unit designs, their costs and delivery times. The complexity of dismantling works sites mean that each is a special case to be dealt with almost independently. Such a way of approaching these projects is not on the same wavelength as industry, with tool and method standardization. The answer to the challenge of operations in difficult environments is an eco-system of functions, performed by a set of inter-connected robots. The first step towards the construction of such robot teams is devoted to functions where strength is not necessary: investigating and clean-up in hostile environments. With this in mind, the CEA Marcoule teams have been given the objective of merging the strengthening commercial robotic world with the needs of D and D, and thus to improve the transversal use of the systems. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Characterization Strategy of a Limited Number of Radioactive Waste Effluent Tanks in View of Decommissioning a Large Number of Tanks - 20286

In order to organize the D and D of the former effluent treatment facility at the CEA Cadarache Center (France), the key data to gather through the facility characterization are the following:: volumes and masses, liquid/solid distribution and specific activity. By studying the treatment processes and the history of the facility, families of tanks have been defined and a reference tank chosen for investigation in each family. The intrusive investigations (video, residue thickness, dose rate..), the gamma spectrometry measurements carried out on site on the residue samples and radiochemical results collected in laboratories, led us to conclude that there was a relative radiological homogeneity (for specific activity and Am-241/Cs-137 ratio) within each tank. The next step consisted in extrapolating the specific activity evaluated for the reference tanks, to the other tanks of each family by using data such as geometry, dose rate or the function of the tanks within the process. Thus, a cartography of the 130 tanks of the facility is available. Finally, the conclusions drawn from the radiological homogeneity of the tanks and their affiliation to homogeneous, well-identified tank clusters lead to a simple and efficient operational approach for the D and D of the 130 tanks of the facility. Indeed, because of the residue characteristics (homogeneous activity and strong differentiation of Cs/Am ratio), a sample collected when opening the tank, and measured on site by gamma spectrometry will allow us to validate the operational design and the emptying techniques defined during the D and D study phase thanks to the characterization of a limited number of reference tanks. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

CIRCEE v1 - a versatile tool for criticality accident dose assessment - 14527

CIRCEE is a calculation code developed by the French Atomic Energy Commission (CEA), allowing fast assessment of operational dose over complex geometries. It is used to assess dosimetric consequences of a criticality accident. More specifically, it can be used both during the preliminary studies phase (isodoses curves for safety report preparation or emergency preparedness, CAAS implantation and validation...) and during crisis management (effective dose estimation, emergency response). An early development stage of CIRCEE has been presented in a talk at the 2009 NCSD edition [1]. Since then, an extensive code rewriting increased its reliability and maintainability while keeping its performance at an excellent level. Now in a stable production version, and following the grant of several international patents, it should be available under commercial license terms in the near future. (author)

42 ENGINEERING↗