Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Microstructural properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Formation of gradient microstructure and mechanical properties of hot-pressed W-20 wt% Cu composites after sliding friction severe deformation

Highlights: • W particles of composites were refined during sliding friction treatment (SFD). • Dislocation, dislocation tangles and boundary clearly exist in deformed W particle. • YS and UTS of SFDed sample are 308.74 MPa and 553.60 MPa owing to the refinement. • Electrical conductivity of SFDed sample decreased from 33 IACS% to 28.5 IACS%. • Fracture mode changing from inter-granular mode to trans-granular. - Abstract: W-based alloys are currently considered promising candidates for high heat flux components in future fusion reactors. In this paper, hot pressed W-20 wt%Cu composites were treated at room temperature using a sliding friction severe deformation (SFD) process, with a moving speed of 0.2 m/s and an applied load of 500 N. Microstructural evolution of composites after the SFD treatment was evaluated and compared with that of the untreated composites. Results showed that there was a gradient structure generated and an obvious refinement in tungsten particles size in the surface layer after the SFD process. The average particle size of tungsten in the SFD treated composites was 2.60 μm, whereas it was 4.5 μm for tungsten in the untreated composites. Fracture surfaces of the composites indicated that the SFD treatment destroyed the W skeleton and changed fracture mode from predominant inter-granular one to trans-granular one due to the decrease in contact area of W-W inter-particles. Yield strength and ultimate tensile strength of composites after the SFD treatment were 308 MPa and 553 MPa, respectively. The treated composites exhibited micro-hardness values with an average reading of about 308 HV. Analysis of the facture microstructures clearly suggested that the tungsten particles in the treated composites are consisted of dislocations and boundaries as well as dislocation tangles. The electrical conductivity of the composites was decreased from 33 IACS% to 28.5 IACS% after the SFD treatment, mainly due to loss or squeezing of copper into the inner surface.

36 MATERIALS SCIENCE↗
DOE OSTI2019

The Effect of Weld Metal Composition on Microstructural and Mechanical Properties of Dissimilar Welds Between Monel 400 and Inconel 600

The current work was carried out to characterize welding of Inconel 600 superalloy and Monel 400. In the present study, gas tungsten arc welding (GTAW) with four types of filler metals (ENiCu, ENiCu-7, ENiCr-3 and ENiCrFe-3) was utilized. The filler metals were categorized into two groups based on the presence of Cr and Nb in their chemical composition. This paper describes the selection and application of welding consumables in manufacturing dissimilar metal combinations. It was found that (Nb/Cr) ratio and Fe content can affect on the size and amount of carbides. During solidification of ENiCr-3 and ENiCrFe-3 filler metals, Nb leaves dendritic cores and is rejected to inter-dendritic regions because of its high tendency for segregation. However, No brittle Laves phase was detected in the welds. The interface between weld metal and base metal and gradual changes in alloying elements were also investigated by scanning electron microscopy. EDX analysis was also applied for different samples. Microhardness measurements and tensile test were performed on the joints. The average hardness value in the weld metal obtained from ENiCrFe-3 is higher than the other welds. ENiCu-7 weld exhibited the highest tensile strength of 540 MPa and percent elongation of 53% in contrast to ENiCrFe-3 weld with the lowest tensile strength (518 MPa) and percent elongation (39%).

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of Ti Addition on the Microstructure and Mechanical Properties of Weld Metals in HSLA Steels

Acicular ferrite (AF) can significantly improve the mechanical properties of steel welds. One practical approach to enhance the formation of AF is to provide the heterogonous nucleation sites such as Ti oxides. In this study, Ti was added to different conventional welding processes including shield metal arc welding (SMAW), submerged arc welding (SAW) and tandem SAW (T-SAW). In the SMAW process, TiO{sub 2} particles as a source of Ti were inserted into the weld groove, while in the SAW and the T-SAW processes, the Ti-enriched S2MoTB wire was used as the filler metal. The microstructural evolution of weldments was characterized by employing optical and scanning electron microscopes. In addition, microhardness (Vickers, HV), Charpy impact and tensile tests were carried out to investigate the mechanical properties of weldments. Although the microhardness measurements of all weldments did not vary significantly and were in the range of 205-252 HV, there was a considerable difference in tensile and impact properties of the SAW and the T-SAW weldments. In the SMAW process, the addition of TiO{sub 2} results in no significant enhancement in tensile and impact toughness. This can be attributed to the inhomogeneous distribution of TiO{sub 2} particles as well as the formation of large inclusions in the structure. On the other hand, Ti addition to WM increased the yield strength from 489 to 552 MPa for the SAW process, and in contrast, it decreased the impact toughness from 75 to 33 J. This detrimental effect can be related to the higher deposition of other alloying elements in the WM and the formation of more ferrite side plate phase. By applying the T-SAW process, more Ti in WM led to a higher content of AF in the microstructure and increased both yield strength and impact toughness from 528 to 595 MPa and 100 to 180 J, respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Microstructural and infiltration properties of woven preforms during chemical vapor infiltration

Interface-resolved direct numerical simulations (DNSs) of chemical vapor infiltration (CVI) have been performed over a range of furnace-operating conditions (Thiele moduli) and for practical woven preform geometries. A level-set method is used to resolve the geometry of the initial preform at tow scale. The interface between the vapor and solid phase is then evolved in time through the entire CVI densification cycle, fully resolving the time-varying topology between the two phases. In contrast to previous level-set methods for CVI simulation, the physical reaction and diffusion processes govern the level-set movement in the current approach. The surface deposition kinetics is described by the usual one-step model. In this paper, the DNS data are used to study the evolving porosity, surface-to-volume ratio, and flow infiltration properties (permeability and effective diffusivities). Additionally, comparisons are made to popularly-assumed structure functions and the standard, Kozeny–Carmen porous media model commonly employed in modeled CFD simulations of CVI. The virtual DNS experiments reveal a Thiele modulus and preform geometry (fabric layup) dependence which the existing microstructural and infiltration models are not able to describe throughout the entire densification process. The DNS-based, woven geometry-specific correlations can be applied directly to mean-field, furnace-scale CFD simulations.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Microstructure and mechanical properties of pure copper wire produced by shear assisted processing and extrusion

Shear assisted processing and extrusion (ShAPE) process can consolidate powdered materials and simultaneously extrude wire or tube with improved properties. We successfully produced copper wire extrusions from powder and solid materials for the first time. The extrusion pressure of ShAPE process is at least two times less than that required for conventional extrusion. We used optical microscopy to inspect and validate the integrity of extrudates. It shows that the microstructure was refined and dynamically recrystallized to equiaxial grains. Compared to the annealed copper wire, ShAPE processed wire has 80% higher yield strength, 15% higher ultimate tensile strength and 20% higher ductility. These were correlated with refined grain size and sub-structuring observed via electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM).

Copper, Wire, Shear Assisted Processing and Extrus↗
NASA NTRS2011

Evaluation of Aluminum Alloy 2050-T84 Microstructure and Mechanical Properties at Ambient and Cryogenic Temperatures

Aluminum alloy 2050 is being considered for the fabrication of cryogenic propellant tanks to reduce the mass of future heavy-lift launch vehicles. The alloy is available in section thicknesses greater than that of the incumbent aluminum alloy, 2195, which will enable designs with greater structural efficiency. While ambient temperature design allowable properties are available for alloy 2050, cryogenic properties are not available. To determine its suitability for use in cryogenic propellant tanks, tensile, compression and fracture tests were conducted on 4 inch thick 2050-T84 plate at ambient temperature and at -320degF. Various metallurgical analyses were also performed in order to provide an understanding of the compositional homogeneity and microstructure of 2050.

Hafley, Robert A.↗
DOE OSTI2024

Microstructure and Mechanical Properties of Ni-based Alloys Fabricated by Laser Powder Bed Fusion

The Advanced Materials and Manufacturing Technologies (AMMT) program is aiming at the accelerated incorporation of new materials and manufacturing technologies into nuclear-related systems. Complex Ni-based components fabricated by laser powder bed fusion (LPBF) could enable operating temperatures at T > 700°C in aggressive environments such as molten salts or liquid metals. However, available mechanical properties data relevant to material qualification remains limited, in particular for Ni-based alloys routinely fabricated by LPBF such as IN718 (Ni- 19Cr-18Fe-5Nb-3Mo) and Haynes 282 (Ni-20Cr-10Co-8.5Mo-2.1Ti-1.5Al). Creep testing was conducted on LPBF 718 at 600°C and 650°C and on LPBF 282 at 750°C. finding that the creep strength of the two alloys was close to that of wrought counterparts. with lower ductility at rupture. Heat treatments were tailored to the LPBF-specific microstructure to achieve grain recrystallization and form strengthening γ' precipitates for LPBF 282 and γ' and γ" precipitates for LPBF 718. In-situ data generated during printing and ex-situ X-ray computed tomography (XCT) scans were used to correlate the creep properties of LPBF 282 to the material flaw distribution. In- situ data revealed that spatter particles are the potential causes for flaws formation in LPBF 282. with significant variation between rods based on their location on the build plate. XCT scans revealed the formation of a larger number of creep flaws after testing in the specimens with a higher initial flaw density. which led to a lower ductility for the specimen.

Dryepondt, Sebastien↗
DOE OSTI2020

Transient Microstructure Evolutions and Local Properties of Dual-Phase 980 MPa Grade Steel Via Friction Stir Spot Processing

Friction stir processing is a novel solid-state process to modify microstructures and their properties by intense, localized plastic deformation. However, little research has been reported for microstructure evolutions of advanced high-strength steels during the process. The present work focuses on the study of transient microstructure changes and local mechanical properties for friction stir spot processed dual-phase (DP) 980 MPa grade steel (DP980) under different peak temperatures. A pinless silicon nitride ceramic tool was used to produce relatively simple material deformation and flow near the tool. Friction stir spot processed steel samples were characterized by optical and electron microscopies. Furthermore, Vickers microhardness and nano-indentation measurements were used to study local mechanical properties for correlation with microstructures. A swallow layer of refined grains (<0.6 µm) was obtained with a low peak temperature (under 400 °C), whereas higher peak temperatures (>Ac 1 ) led to a change in grain size with different microstructures (fine-grained DP or martensite). Electron back-scattered diffraction characterizations revealed a large deformation in the as-received microstructures (mixture of ferrite and tempered martensite) induced by friction stir spot processing, leading to recrystallization and grain refinement around the stirred zone. Also, nano-indentation measurements showed a higher hardness than the hardness of the as-received DP980. Friction stir processing with different process conditions effectively changed microstructures and local mechanical properties.

36 MATERIALS SCIENCE↗
NASA NTRS2002

Effects of Microalloying on the Microstructures and Mechanical Properties of Directionally Solidified Ni-33(at.%)Al-31Cr-3Mo Eutectic Alloys Investigated

Despite nickel aluminide (NiAl) alloys' attractive combination of oxidation and thermophysical properties, their development as replacements for superalloy airfoils in gas turbine engines has been largely limited by difficulties in developing alloys with an optimum combination of elevated-temperature creep resistance and room-temperature fracture toughness. Alternatively, research has focused on developing directionally solidified NiAl-based in situ eutectic composites composed of NiAl and (Cr,Mo) phases in order to obtain a desirable combination of properties a systematic investigation was undertaken at the NASA Glenn Research Center to examine the effects of small additions of 11 alloying elements (Co, Cu, Fe, Hf, Mn, Nb, Re, Si, Ta, Ti, and Zr) in amounts varying from 0.25 to 1.0 at.% on the elevated-temperature strength and room-temperature fracture toughness of directionally solidified Ni-33Al-31Cr-3Mo eutectic alloy. The alloys were grown at 12.7 mm/hr, where the unalloyed eutectic base alloy exhibited a planar eutectic microstructure. The different microstructures that formed because of these fifth-element additions are included in the table. The additions of these elements even in small amounts resulted in the formation of cellular microstructures, and in some cases, dendrites and third phases were observed. Most of these elemental additions did not improve either the elevated-temperature strength or the room-temperature fracture toughness over that of the base alloy. However, small improvements in the compression strength were observed between 1200 and 1400 K when 0.5 at.% Hf and 0.25 at.% Ti were added to the base alloy. The results of this study suggest that the microalloying of Ni-33Al-31Cr-3Mo will not significantly improve either its elevatedtemperature strength or its room-temperature fracture toughness. Thus, any improvements in these properties must be acquired by changing the processing conditions.

Whittenberger, J. Daniel↗
DOE OSTI2023

Achieving superior mechanical properties: Tailoring multicomponent microstructure in AISI 9254 spring steel through a two-stage Q&P process and nanoscale carbide integration

In the pursuit of lightweight, durable steel, we have successfully developed a multicomponent structure in AISI 9254 spring steel using a two-stage quenching and partitioning (Q&P) process. The primary objective of this process was to engineer an optimized microstructure consisting of nanobainite, martensite, and nano-carbides. Utilizing the insights gained from the results of advanced techniques such as X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and atom probe tomography (APT) performed on the as-received AISI 9254 spring steel, we refined the quenching and partitioning (Q&P) path, leading to the successful establishment of a bainitic transformation for superior mechanical properties. Our tensile tests revealed a high yield strength (≈ 1600 ± 25 MPa) and ultimate tensile strength (≈ 1850 ± 50 MPa), along with considerable elongation (≈ 11.15 ± 0.25%). We also identified that pre-formed martensite lath defects and high silicon content play crucial roles during the Q&P process, preventing carbide coalescence and increasing strain-hardening capacity. Finally, this study demonstrates the potential of a Q&P process to generate high-strength, ductile steel for automotive and aerospace applications.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effect of preheat temperature and post-process treatment on the microstructure and mechanical properties of stainless steel 410 made via ultrasonic additive manufacturing

Ultrasonic additive manufacturing (UAM) is a solid-state manufacturing technology for producing near-net shape metallic parts combining additive ultrasonic metal welding and subtractive machining. Even though UAM has been demonstrated to produce robust metal builds in Al–Al, Al–Ti, Al-steel, Cu–Cu, Al–Cu, and other material systems, UAM welding of high strength steels has proven challenging. This study investigates process and post-processing methods to improve UAM steel weld quality and demonstrates the UAM fabrication of stainless steel 410 (SS 410) builds which possess, after post-processing, mechanical properties comparable with bulk material. Unlike UAM fabrication of softer metals, this study shows that increasing the baseplate temperature from 38°C (100°F) to 204°C (400°F) improves interfacial strength and structural homogeneity of the UAM steel samples. Further improvement in strength is achieved through post-processing. The hot isostatic pressing (HIP) post treatment improves the shear strength of UAM samples to 344 MPa from 154 MPa for as-welded samples. Microstructural analyses with SEM and EBSD show no evidence of body centered cubic (BCC) ferrite to face centered cubic (FCC) austenite transformation taking place during UAM welding of SS 410. The weld quality improvement of UAM steel at higher baseplate temperatures is believed to be caused by the reduction of the yield strength of SS 410 at elevated temperature. Finaly, HIP treatment is shown to increase the overall hardness of UAM SS 410 from 204 ± 7 HV to 240 ± 16 HV due to the formation of local pockets of martensite. Nanohardness tests show that the top of layer n is harder than the bottom of layer n+1 due to grain boundary strengthening.

36 MATERIALS SCIENCE↗
NASA NTRS1990

Microstructure and mechanical properties of multiphase NiAl-based alloys

The effect of the gamma-prime phase on the deformation behavior and fracture resistance of melt-spun ribbons and consolidated bulk specimens of a series of Nial-based alloys with Co and Hf additions has been examined. The morphology, location, and volume fraction of the gamma-prime phase are significant factors in enhancing the fracture resistance of the normally brittle NiAl-based alloys. In particular, the results indicate that a continuous-grain-boundary film of gamma-prime can impart limited room-temperature ductility regardless of whether B2 or L10 NiAl is present. Guidelines for microstructure control in multiphase NiAl-based alloys are also presented.

Pank, D. R.↗
DOE OSTI2018

Effect of Zinc Interlayer in Microstructure Evolution and Mechanical Properties in Dissimilar Friction Stir Welding of Aluminum to Titanium

The welding of aluminum (Al) and titanium (Ti) is difficult and challenging due to the differences in their chemical and physical properties, and the formation of brittle intermetallic phases. In the present experiment, a zinc (Zn) interlayer was used during friction stir welding of Al to Ti. The weld was characterized in detail to understand the mechanisms associated with microstructural evolution and improvement in mechanical properties of the weld. X-ray computed tomography results reveal three-dimensional distribution of particles and flakes of titanium in the weld nugget. It was also observed that Ti particles are inhomogeneously distributed in the weld and the distribution depends on their morphology. Such a distribution of Ti was informative in understanding material flow. In addition, the consolidation of Zn in the Al matrix reveals the nature of material flow in the weld nugget as well. The importance of the Zn interlayer and mechanism of phase formation was explored in this study. It was characterized that the mechanical mixing of Zn with Al and Ti alters phase evolution and restricts the formation of conventional Al{sub 3}Ti intermetallic phase. The presence of zinc homogenizes elemental distribution and inhibits the formation of brittle intermetallic phases, which leads to a substantial improvement in mechanical properties of the weld.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Investigating the effect of different shielding gas mixtures on microstructure and mechanical properties of 410 stainless steel fabricated via large scale additive manufacturing

Metal Big Area Additive Manufacturing (mBAAM) offers the potential to fabricate large scale tools at high deposition rates (15 lb/h+). 410 martensitic steel is a potential tooling material, owing to its low cost, good machinability and reasonable printability. During the mBAAM process, the shielding gas can have a significant impact on the material properties as well as the process cost. Therefore, the current study aims to understand the effect of different shielding gas mixtures on large-scale additive manufacturing of 410 martensitic stainless steel. We show that an argon mixture with 3% nitrogen gas produced the best performance in terms of maximum hardness and tensile strength, with much less scatter in tensile strength. He-Ar-CO 2 or tri-mix shielded samples showed a low tensile strength with wide scatter, due to stabilized delta ferrite in microstructure during printing. Both tri-mix and Ar-CO 2 shielded samples showed slightly higher porosity. Thus, we recommend the use of argon-3% nitrogen as a shielding gas mixture for processing 410 steel for tool applications, based on the relatively low cost of this gas mixture and the resulting higher hardness, higher dimensional stability, and lower porosity.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effect of Tempering Mode on the Microstructure and Mechanical Properties of a Lean Alloy Martensitic Steel: Conventional Reheating Versus Induction Reheating

The present study elucidates the effect of the reheating rate and tempering temperature on the type, size, and distribution of carbides/cementite formed within martensite (M)/lower bainite (LB) during the tempering of a high-strength low-alloy (HSLA) steel. A comparison is made between conventional reheating and induction reheating. All the experimental samples were quenched from the austenitization temperature of 920 °C for 30 min. An ultra-high yield strength of 1180 MPa and a good toughness of 94 J at 0 °C were obtained after tempering at 400 °C for 15 min by induction reheating (~ 100 °C/s), while in the case of conventional reheating (~ 2 °C/s) and tempering at 400 °C for 15 min, the steel had a high strength of 1159 MPa, but a poor toughness of 47 J at 0 °C. After induction reheating to 500 °C and tempering for 15 min, a higher toughness was obtained (91 J at 0 °C), but the strength was decreased to 967 MPa. Microstructural characterization revealed that fine needle-like carbides (ε-Fe{sub 2.4}C) were obtained by induction reheating to 400 °C and tempering for 15 min. However, samples tempered at 400 °C by conventional reheating and 500 °C by induction reheating both precipitated coarse θ-Fe{sub 3}C. In the former, θ-Fe{sub 3}C precipitated at locations that were previously austenite grain boundaries and led to tempered martensite embrittlement (TME). In the latter, Ostwald ripening occurred, and the precipitates could not maintain high strength. The excellent mechanical properties of induction reheated steel (400 °C, 15 min) are attributed to the following aspects: (a) The selection of appropriate tempering temperature did not lead to decarburization and ensured high strength, and (b) a high reheating rate promoted carbide dispersion and avoided TME in steel.

36 MATERIALS SCIENCE↗
NASA NTRS2000

Effects of Thermal and Mechanical Processing on Microstructures and Desired Properties of Particle-Strengthened Cu-Cr-Nb Alloys

Ternary Cu-Cr-Nb alloys, particularly Cu-8 Cr-4 Nb (in at.%), have demonstrated good thermal stability as well as high strength and conductivity at elevated temperatures. The initial powder material has a bimodal size distribution of Cr2Nb precipitates. Primary Cr2Nb precipitates are approx. 1 micron, and secondary Cr2Nb particles are 30-200 nm. The particle coarsening was analyzed and found to follow LSW-type behavior, This study provides a detailed examination of the stability and strengthening effects of Cr2Nb particles. This investigation also revealed that the primary particles provide direct grain boundary pinning and indirect grain boundary strengthening but virtually no Orowan strengthening. The secondary particles found within grains do provide Orowan strengthening. For extruded material, grain bound-ary strengthening (Hall-Petch effect) accounts for two-thirds of the strength with Orowan effects contributing the remainder. The proven advantages of Cu-Cr-Nb were the motivation to improve these attributes via microstructural refinement. Mechanical milling (MM) of Cu- 4 Cr-2 Nb and Cu-8 Cr-2 Nb produced an increase in hot pressed Vickers hardness of 122% and 96%, respectively. The increase in hardness was more due to Cu grain-size refinement than to Cr,,Nb refinement. This study also demonstrated enhanced stability of MM Cu-4 Cr-2 Nb. Hot pressed 4 h milled Cu-4 Cr-2 Nb experienced only a 22% drop in hardness when annealed at 1273 K for 50 h versus a 30% drop for extruded Cu-8 Cr-4 Nb. The goal of improving the strength and stability of Cu-4 Cr-2 Nb to better than such properties for as- extruded Cu-8 Cr-4 Nb has been met. In addition, a figure-of-merit (FOM) coupling hardness and thermal conductivity was maximized for the case of 4 h milled Cu-4 Cr-2 Nb material. Overall, Cu-Cr-Nb alloys not only possess high strength, conductivity and thermal stability but also can be further developed to improve strength and stability.

Anderson, Kenneth Reed↗