Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LOW SPEED STABILITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

1.3-µm passively mode-locked quantum dot lasers epitaxially grown on silicon: gain properties and optical feedback stabilization

Abstract This work reports on an investigation of the optical feedback in an InAs/InGaAs passively mode-locked quantum dot (QD) laser epitaxially grown on silicon. Under the stably-resonant optical feedback condition, experiments demonstrate that the radio-frequency linewidth is narrowed whatever the bias voltage applied on the saturable absorber (SA) is; on the other hand, the effective linewidth enhancement factor of the device increases with the reverse bias voltage on the SA, hence it is observed that such an increase influences the mode-locking dynamic and the stability of device under optical feedback. This work gives insights for stabilizing epitaxial QD mode-locked lasers on silicon which is meaningful for their applications in future large-scale silicon electronic and photonic applications requiring low power consumption as well as for high-speed photonic analog-to-digital conversion, intrachip/interchip optical clock distribution and recovery.

Dong, Bozhang (ORCID:0000000158266723)↗
NASA NTRS1991

On the interaction between first- and second-mode waves in a supersonic boundary layer

Linear stability theory predicts two or more types of unstable disturbances in a sufficiently high-speed boundary layer. These include the first mode, which is similar to the Tollmien-Schlichting waves found in low-speed flows, and the second mode, which does not depend strongly on the viscosity. Generally, the most unstable first mode is three-dimensional while the most unstable second mode is two-dimensional. The interaction between these two spatially unstable modes are studied by direct solution of the three-dimensional Navier-Stokes equations. It is found that the two-dimensional second mode causes a significant increase in the nonlinearity and in the three-dimensionality of the flowfield. The results suggest that this interaction may accelerate transition for flows where the second mode has a significant growth rate.

Maestrello, L.↗
NASA NTRS1994

Third order LPF type compensator for flexible rotor suspension

The tuning job of the compensator for levitating flexible rotors supported by active magnetic bearings (AMB) concerns providing a good damping effect to the critical speed modes while avoiding the spillover problem on the instability of higher bending modes. In this paper, an idea for design of the control law of the compensator based on utilizing a third order low pass filter (LPF) is proposed to essentially enable elimination of the spillover instability. According to the proposed design method, good damping effects for the critical speeds are obtained by the usual phase lead/lag function. Stabilization for all of higher bending modes is completed by the additional function of the 3rd order LPF due to its phase lag approaching about -270 degrees in the high frequency domain. This idea is made clear by experiments and simulations.

Matsushita, Osami↗
NASA NTRS1996

Research In Nonlinear Flight Control for Tiltrotor Aircraft Operating in the Terminal Area

The research during the first year of the effort focused on the implementation of the recently developed combination of neural net work adaptive control and feedback linearization. At the core of this research is the comprehensive simulation code Generic Tiltrotor Simulator (GTRS) of the XV-15 tilt rotor aircraft. For this research the GTRS code has been ported to a Fortran environment for use on PC. The emphasis of the research is on terminal area approach procedures, including conversion from aircraft to helicopter configuration. This report focuses on the longitudinal control which is the more challenging case for augmentation. Therefore, an attitude command attitude hold (ACAH) control augmentation is considered which is typically used for the pitch channel during approach procedures. To evaluate the performance of the neural network adaptive control architecture it was necessary to develop a set of low order pilot models capable of performing such tasks as, follow desired altitude profiles, follow desired speed profiles, operate on both sides of powercurve, convert, including flaps as well as mastangle changes, operate with different stability and control augmentation system (SCAS) modes. The pilot models are divided in two sets, one for the backside of the powercurve and one for the frontside. These two sets are linearly blended with speed. The mastangle is also scheduled with speed. Different aspects of the proposed architecture for the neural network (NNW) augmented model inversion were also demonstrated. The demonstration involved implementation of a NNW architecture using linearized models from GTRS, including rotor states, to represent the XV-15 at various operating points. The dynamics used for the model inversion were based on the XV-15 operating at 30 Kts, with residualized rotor dynamics, and not including cross coupling between translational and rotational states. The neural network demonstrated ACAH control under various circumstances. Future efforts will include the implementation into the Fortran environment of GTRS, including pilot modeling and NNW augmentation for the lateral channels. These efforts should lead to the development of architectures that will provide for fully automated approach, using similar strategies.

Calise, A. J.↗
NASA NTRS2023

CFD Integrated Transition Modeling for High-Speed Flows via Coupled OVERFLOW-LASTRAC Analysis

This work details ongoing efforts at the NASA Langley Research Center to develop and validate a general-use CFD tool that includes built-in predictions of boundary-layer transition in high-speed flows. Existing tools for the coupling of the NASA OVERFLOW structured overset RANS solver and LASTRAC stability analysis code have been extended to capture boundary-layer transition in high-speed flows driven by either Mack’s first-mode or secondmode instabilities and/or crossflow instabilities. The efficacy of this coupled approach has been demonstrated by examining a variety of supersonic and hypersonic test cases for which experimental validation data is available. The intermittency prescription parameters inherited from prior low-speed applications are found to be suitable for some, but not all high-speed flow scenarios. The method is found to be robust for straight cone configurations and improvements necessary to accurately capture transition on geometries with spatially complex amplification factor envelopes with intermediate regions of slow N-factor variation are examined. The automated, coupled analysis is demonstrated for a 3d supersonic test case and found to perform well within the limits of the linear stability analysis on which it relies. Finally, a preliminary investigation of the method’s robustness to non-ideal CFD meshes is conducted.

High-speed flow↗
NASA NTRS1997

Massively Parallel and Scalable Implicit Time Integration Algorithms for Structural Dynamics

Explicit codes are often used to simulate the nonlinear dynamics of large-scale structural systems, even for low frequency response, because the storage and CPU requirements entailed by the repeated factorizations traditionally found in implicit codes rapidly overwhelm the available computing resources. With the advent of parallel processing, this trend is accelerating because of the following additional facts: (a) explicit schemes are easier to parallelize than implicit ones, and (b) explicit schemes induce short range interprocessor communications that are relatively inexpensive, while the factorization methods used in most implicit schemes induce long range interprocessor communications that often ruin the sought-after speed-up. However, the time step restriction imposed by the Courant stability condition on all explicit schemes cannot yet be offset by the speed of the currently available parallel hardware. Therefore, it is essential to develop efficient alternatives to direct methods that are also amenable to massively parallel processing because implicit codes using unconditionally stable time-integration algorithms are computationally more efficient when simulating the low-frequency dynamics of aerospace structures.

Farhat, Charbel↗
NASA NTRS2021

The Causes of Propeller Pitching Moment and the Conditions for its Significance

Recent development of vertical takeoff and landing (VTOL) aircraft has renewed interest in the study of propellers. One metric in particular, the propeller pitching moment, has been observed to be important to VTOL aircraft stability and control in the past. Propellers at angles of attack could not be accurately modeled in generations past due to a lack of computational power, but even with advances in computer technology, modern designers seem to possess insufficient knowledge in this area. In this dissertation, we study the physics behind propeller pitching moment in the context of an isolated propeller and a propeller upstream of a wing. An unsteady 3D vortex lattice method is developed specifically to model propellers at angles of attack and is validated by comparing to high-fidelity CFD analyses. We then use the model to isolate velocity influences to show that the propeller pitching moment is largely caused by two effects: a skewed wake and the presence of wing circulation. Generated maps of propeller pitching moment over a range of operational parameters corresponding to VTOL transition show that the low flight speeds and high angles of attack encountered during transition lead to significant magnitudes of propeller pitching moment that would be difficult to trim using passive methods. Also, derivation of a generalizable metric of significance shows that the peak contribution of propeller pitching moment to aircraft stability is comparable to a longitudinal displacement of the center of gravity by several percent of the wing chord. Finally, we give a concluding discussion on the impact of propeller pitching moment on VTOL aircraft design.

Xiaofan Fei↗
NASA NTRS1972

Low speed aerodynamic characteristics of a large scale model with a thin, highly swept, 2.67 aspect ratio wing having a cranked leading edge

The low speed aerodynamic characteristics of a large-scale model intended to represent advanced fixed-wing fighters have been investigated in the Ames 40 by 80 foot wind tunnel. The model possessed positive static longitudinal stability to nearly 28 deg angle of attack, the maximum tested, both with and without leading-edge flaps deflected. Lateral control with differentially deflected ailerons and a right wing spoiler simultaneously deployed as combined controls was only slightly greater than that with the differentially deflected ailerons deployed as a separate control without the spoiler. Measured lift and drag were in close agreement with that predicted by theory to about 14 deg angle of attack, including the prediction of lift due to 30 deg of trailing edge flap deflection. Estimated takeoff performance of an aircraft 4/3 the scale of the test model showed takeoff distances of less than 2000 ft.

Giulianetti, D. J.↗
NASA NTRS1991

Nonlinear Dynamic Compensation For Feedback Control

Nonlinear dynamic compensation scheme enhances stability of feedback control system in which feedback signal includes quantization noise. Compensator slows response of control system at low error signals to diminish effect of quantization noise but provides faster response at large error signals to speed correction of large errors.

Lin, Yu-Hwan↗
NASA NTRS1942

The Longitudinal Stability of Flying Boats as Determined by Tests of Models in the NACA Tank II : Effect of Variations in Form of Hull on Longitudinal Stability

Data taken from tests at constant speed to establish trim limits of stability, tests at accelerated speeds to determine stable limits of center of gravity shift, and tests at decelerated speeds to obtain landing characteristics of several model hull forms were used to establish hull design effect on longitudinal stability of porpoising. Results show a reduction of dead rise angle as being the only investigated factor reducing low trim limit. Various methods of reducing afterbody interference increased upper trim limit

Olson, Roland E.↗
NASA NTRS1998

Distortion Tolerant Control Demonstrated in Flight

Future aircraft turbine engines, both commercial and military, will have to be able to successfully accommodate expected increased levels of steady-state and dynamic engine-face distortion. Advanced tactical aircraft are likely to use thrust vectoring for enhanced aircraft maneuverability. As a result, the engines will see more extreme aircraft angle-of-attack alpha and sideslip beta levels than currently encountered with present-day aircraft. Also, the mixed-compression inlets needed for the High Speed Civil Transport (HSCT) will likely encounter disturbances similar to those seen by tactical aircraft, in addition to planar pulse, inlet buzz, and high distortion levels at low flight speed and off-design operation. The current approach of incorporating sufficient component design stall margin to tolerate these expected levels of distortion would result in significant performance penalties. The objective of NASA's High Stability Engine Control (HISTEC) program is to design, develop, and flight demonstrate an advanced, high-stability, integrated engine control system that uses measurement-based real-time estimates of distortion to enhance engine stability. The resulting distortion tolerant control adjusts the stall margin requirement online in real-time. This reduces the design stall margin requirement, with a corresponding increase in performance and decrease in fuel burn.

DeLaat, John C.↗
NASA NTRS1999

Distortion Tolerant Control Flight Demonstration Shown to Be Successful

Future aircraft turbine engines, both commercial and military, will have to be able to successfully accommodate expected increased levels of steady-state and dynamic engine-face distortion. Advanced tactical aircraft are likely to use thrust vectoring for enhanced aircraft maneuverability. As a result, the engines will see more extreme distortion levels than currently encountered with present-day aircraft. Also, the mixed-compression inlets needed for the High-Speed Civil Transport (HSCT) will likely encounter disturbances similar to those seen by tactical aircraft, in addition to planar pulse, inlet buzz, and high distortion levels at low flight speed and off-design operation. The current approach of incorporating sufficient component design stall margin to tolerate these expected levels of distortion would result in significant performance penalties. The objectives of NASA's High Stability Engine Control (HISTEC) program, which has reached a highly successful conclusion, were to design, develop, and flight demonstrate an advanced, high-stability, integrated engine control system that uses measurement-based real-time estimates of distortion to enhance engine stability. The resulting distortion tolerant control adjusts the stall margin requirement online in real time. This reduces the design stall margin requirement, with a corresponding increase in performance and decrease in fuel burn.

Litt, Jonathan S.↗
NASA NTRS2006

Performance, Loads and Stability of Heavy Lift Tiltrotors

Summaries of rotor performance are presented for a 124,000-lb Large Civil Tilt Rotor (LCTR) design, along with isolated-rotor and fully-coupled wing/rotor aeroelastic stability. A major motivation of the present research is the effect of size on rotor dynamics. Simply scaling up existing rotor designs to the vehicle size under study would result in unacceptable rotor weight. The LCTR was the most promising of several large rotorcraft concepts produced by the NASA Heavy Lift Rotorcraft Systems Investigation. It was designed to carry 120 passengers for 1200 nm, with performance of 350 knots at 30,000 ft altitude. Design features included a low-mounted wing and hingeless rotors, with a very low cruise tip speed of 350 ft/sec. The LCTR was sized by the'RC code developed by the U. S. Army Aeroflightdynamics Directorate. The rotor was then optimized using the CAMRAD II comprehensive analysis code. The blade and wing structures were designed by Pennsylvania State University to meet the rotor loads calculated by CAMRAD II and wing loads required for certification. Aeroelastic stability was confirmed by further CAMRAD II analysis, based on the optimized rotor and wing designs.

Acree, Cecil W., Jr.↗
NASA NTRS1978

Modification of the Douglas Neumann program to improve the efficiency of predicting component interference and high lift characteristics

The Douglas Neumann method for low-speed potential flow on arbitrary three-dimensional lifting bodies was modified by substituting the combined source and doublet surface paneling based on Green's identity for the original source panels. Numerical studies show improved accuracy and stability for thin lifting surfaces, permitting reduced panel number for high-lift devices and supercritical airfoil sections. The accuracy of flow in concave corners is improved. A method of airfoil section design for a given pressure distribution, based on Green's identity, was demonstrated. The program uses panels on the body surface with constant source strength and parabolic distribution of doublet strength, and a doublet sheet on the wake. The program is written for the CDC CYBER 175 computer. Results of calculations are presented for isolated bodies, wings, wing-body combinations, and internal flow.

Bristow, D. R.↗
NASA NTRS1985

Lower-hybrid instabilities driven by an ion velocity ring

The lower-hybrid instabilities in high-beta (ratio of plasma to magnetic pressure) plasmas driven by ring-ion distributions in velocity space are investigated. A dispersion equation including electromagnetic effects is derived. In the low-beta limit, analytic expressions are obtained which illuminate the physical nature of the instabilities. The complete dispersion equation is solved numerically as a function of ring speed and plasma beta for several types of ring distribution. Electromagnetic effects are important for relatively energetic rings even in the low-beta regime, suppressing growth rates and shifting the angle of propagation to more oblique angles. Stabilization by thermal effects is also discussed. Application of these results to the earth's bow shock, AMPTE, comets and solar flares is suggested.

Akimoto, K.↗
NASA NTRS2002

Saltation Impact as a Means for Raising Dust on Mars

Experiments were conducted under atmospheric pressures appropriate for Earth and Mars to determine the efficiency of sand in saltation as a means for raising dust into the atmosphere under wind speeds which would otherwise be too low for dust entrainment. Experiments involving intimate mixtures of sand and dust (1:1 ratio by mass) showed that after an initial flurry of activity of a few seconds duration, the bed stabilized with little movement of either sand or dust. In contrast, sands set into saltation upwind fro= dust beds were efficient in injecting the dust into suspension, with low-pressure Martian conditions being some five times more efficient than terrestrial conditions. This result is attributed to the higher kinetic energies of the saltating grains on Mars, which is a consequence of the higher velocities of the grains. These results suggest that sands saltating across dust beds on Mars are an effective means for setting dust into suspension.

Greeley, Ronald↗
NASA NTRS2012

Entry, Descent, and Landing for Human Mars Missions

One of the most challenging aspects of a human mission to Mars is landing safely on the Martian surface. Mars has such low atmospheric density that decelerating large masses (tens of metric tons) requires methods that have not yet been demonstrated, and are not yet planned in future Mars missions. To identify the most promising options for Mars entry, descent, and landing, and to plan development of the needed technologies, NASA's Human Architecture Team (HAT) has refined candidate methods for emplacing needed elements of the human Mars exploration architecture (such as ascent vehicles and habitats) on the Mars surface. This paper explains the detailed, optimized simulations that have been developed to define the mass needed at Mars arrival to accomplish the entry, descent, and landing functions. Based on previous work, technology options for hypersonic deceleration include rigid, mid-L/D (lift-to-drag ratio) aeroshells, and inflatable aerodynamic decelerators (IADs). The hypersonic IADs, or HIADs, are about 20% less massive than the rigid vehicles, but both have their technology development challenges. For the supersonic regime, supersonic retropropulsion (SRP) is an attractive option, since a propulsive stage must be carried for terminal descent and can be ignited at higher speeds. The use of SRP eliminates the need for an additional deceleration system, but SRP is at a low Technology Readiness Level (TRL) in that the interacting plumes are not well-characterized, and their effect on vehicle stability has not been studied, to date. These architecture-level assessments have been used to define the key performance parameters and a technology development strategy for achieving the challenging mission of landing large payloads on Mars.

Munk, Michelle M.↗