SEARCH · Engineering Papers

Results for “Inverter”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

All sources NASA NTRS DOE OSTI

NASA NTRS1982

Observations of inverted-V electron precipitation

The energy and pitch angle distributions of inverted-V electron precipitation fluxes predominantly determined from Atmosphere Explorer satellite observations are shown to be in general agreement with acceleration by a parallel electrostatic potential. The characteristics of secondary electrons are examined, and the effects of beam plasma instabilities on these electrons are discussed. It is found that plasma sheet electrons are continuously accelerated to form inverted-V structures in the premidnight hemisphere, independent of substorm phase. The acceleration processes are probably related to large scale, electrostatic wave turbulence observed at altitudes of a few thousands km. It is suggested that narrow bursts of intense electron precipitation possess characteristics which may cause auroral arcs in the atmosphere.

Lin, C. S.↗

NASA NTRS1983

Development of a rotary power transformer and inverter drive for spacecraft

Many future satellites and spacecraft with spun and despun configurations will require the transfer of power across rotating interfaces in lieu of slip-rings and/or flexures. This is particularly true of spacecraft that have to demonstrate a long life expectancy. The rotary transformer has the desirable characteristics of high reliability and low noise, which qualify it as a potential replacement for slip rings. Development of a rotary power transformer follows the successful completion of a task to develop rotary signal-level transformers for the Galileo Spacecraft Project. The physical configuration of a rotary power transformer has a significant effect on its magnetic and electrical characteristics and therefore impacts the design of the dc/ac inverter driver. Important characteristics addressed during this development effort include: operating frequency, efficiency, transformer gap size, leakage inductance, and leakage flux. A breadboard inverter and rotary transformer were designed, fabricated and tested.

Mclyman, W. T.↗

NASA NTRS1984

Vigilance and task load - In search of the inverted U

The 'Inverted-U Hypothesis' states that for a given task, there is an optimal level of workload or demand that yields the highest level of performance. A departure in either direction will result in a monotonically lower performance level, hence an inverted-U-shaped relationship between task demand and quality of performance. Most studies to date have failed to demonstrate the left-hand branch of the curve, that is, the regime in which performance presumably rises as load increases. The purpose of this study was to explore whether low-level additional demand on the monitor would result in improved performance. Four groups of subjects performed a visual monitoring task for 48 min, then two of the four groups were given additional tasks, and a third had potentially distracting information on its display. Results indicated that the two groups with additional demand detected more signals than did the control group or the control-plus-distraction group. There were no significant differences in false alarms.

Wiener, E. L.↗

NASA NTRS1984

High-altitude observations of an intense inverted V event

Inverted-V events which generally occur in the pre-midnight sector over the auroral zone are frequently associated with reversals in the convection electric field. Such a reversal is observed by the University of Iowa quasispherical LEPEDEA on board ISEE 1 at an altitude of 13 RE on May 1, 1978. The bulk of the plasma shows a large shear over a five-minute interval. The associated change in the convection electric field is 5.1 mV/m. Large values of the field-aligned current are simultaneously detected. The potential structure appears to extend to the satellite location. Using a theoretical model, the field-aligned current due to the electric field discontinuity has been calculated. The magnitude of the parallel potential drop and width of the inverted-V region agree well with observation.

Huang, C. Y.↗

NASA NTRS1985

Program Predicts Nonlinear Inverter Performance

Program developed for ac power distribution system on Shuttle orbiter predicts total load on inverters and node voltages at each of line replaceable units (LRU's). Mathematical model simulates inverter performance at each change of state in power distribution system.

Al-Ayoubi, R. R.↗

NASA NTRS1985

Shock associated noise of inverted-profile coannular jets. I - Experiments

The reduction of shock-associated noise in inverted-velocity-profile coannular jets is quantified and explained by conducting extensive optical and acoustic measurements for a suitable range of outer-stream and inner-stream presure-ratio combinations, and by interpreting the measured noise results with the aid of new theoretical models. It is shown that the shock noise from the outer stream is virtually eliminated when the inner stream is operated at a Mach number just above unity, regardless of all the other jet operating parameters. Furthermore, this reduction can be achieved at inverted-velocity-profile as well as normal-velocity-profile conditions.

Tanna, H. K.↗

NASA NTRS1988

A diagonally inverted LU implicit multigrid scheme

A new Diagonally Inverted LU Implicit scheme is developed within the framework of the multigrid method for the 3-D unsteady Euler equations. The matrix systems that are to be inverted in the LU scheme are treated by local diagonalizing transformations that decouple them into systems of scalar equations. Unlike the Diagonalized ADI method, the time accuracy of the LU scheme is not reduced since the diagonalization procedure does not destroy time conservation. Even more importantly, this diagonalization significantly reduces the computational effort required to solve the LU approximation and therefore transforms it into a more efficient method of numerically solving the 3-D Euler equations.

Yokota, Jeffrey W.↗

NASA NTRS1988

A diagonally inverted LU implicit multigrid scheme

A new Diagonally Inverted LU Implicit scheme is developed within the framework of the multigrid method for the three-dimensional unsteady Euler equations. The matrix systems that are to be inverted in the LU scheme are treated by local diagonalizing transformations that decouple them into systems of scalar equations. Unlike the Diagonalized ADI method, the time accuracy of the LU scheme is not reduced since the diagonalizing procedure does not destroy time conservation. Even more importantly, this diagonalization significantly reduces the computational effort required to solve the LU approximation and therefore transforms it into a more efficient method of numerically solving the three-dimensional Euler equations.

Yokota, J. W.↗

NASA NTRS1988

Theoretical investigation of the oceanic inverted barometer response

Dynamic tidal theory is generalized in order to predict the oceanic response to atmospheric pressure variations. The oceans are found to exhibit distinct dynamic behavior when forced at periods less than one week; depending on the harmonic type of forcing, the amplitude of the response can differ by about 20 percent or more from the static response. Even at roughly two months the traditional 'inverted barometer' may not be sufficiently accurate for applications in which detection of long-term sea level trends or vertical crustal motion is the goal. For forcing at periods of order one year the oceanic response differs by at most a few percent from the static (not the inverted barometer) response; thus calculations of meteorological excitation of the annual and Chandler wobbles can employ the static approximation without reservation.

Dickman, S. R.↗

NASA NTRS1989

A design procedure for the phase-controlled parallel-loaded resonant inverter

High-frequency-link power conversion and distribution based on a resonant inverter (RI) has been recently proposed. The design of several topologies is reviewed, and a simple approximate design procedure is developed for the phase-controlled parallel-loaded RI. This design procedure seeks to ensure the benefits of resonant conversion and is verified by data from a laboratory 2.5 kVA, 20-kHz converter. A simple phasor analysis is introduced as a useful approximation for design purposes. The load is considered to be a linear impedance (or an ac current sink). The design procedure is verified using a 2.5-kVA 20-kHz RI. Also obtained are predictable worst-case ratings for each component of the resonant tank circuit and the inverter switches. For a given load VA requirement, below-resonance operation is found to result in a significantly lower tank VA requirement. Under transient conditions such as load short-circuit, a reversal of the expected commutation sequence is possible.

King, Roger J.↗

NASA NTRS2000

Suspended Patch Antennas With Electromagnetically Coupled Inverted Microstrip Feed for Circular Polarization

The paper demonstrates a suspended nearly square patch antenna with offset feed and a square patch antenna with truncated corners for circular polarization. The antennas are excited by an electromagnetically coupled inverted microstrip feed. In addition a new transition between conventional microstrip and inverted microstrip is proposed. The measured results include the axial ratio and the impedance bandwidth of the antennas.

Simons, Rainee N.↗

NASA NTRS2001

Experimental Investigation of Composite Pressure Vessel Performance and Joint Stiffness for Pyramid and Inverted Pyramid Joints

The focus of this study is on the suitability in the application of classical laminate theory analysis tools for filament wound pressure vessels with adhesive laminated joints in particular: pressure vessel wall performance, joint stiffness and failure prediction. Two 18-inch diameter 12-ply filament wound pressure vessels were fabricated. One vessel was fabricated with a 24-ply pyramid laminated adhesive double strap butt joint. The second vessel was fabricated with the same number of plies in an inverted pyramid joint. Results from hydrostatic tests are presented. Experimental results were used as input to the computer programs GENLAM and Laminate, and the output compared to test. By using the axial stress resultant, the classical laminate theory results show a correlation within 1% to the experimental results in predicting the pressure vessel wall pressure performance. The prediction of joint stiffness for the two adhesive joints in the axial direction is within 1% of the experimental results. The calculated hoop direction joint stress resultant is 25% less than the measured resultant for both joint configurations. A correction factor is derived and used in the joint analysis. The correction factor is derived from the hoop stress resultant from the tank wall performance investigation. The vessel with the pyramid joint is determined to have failed in the joint area at a hydrostatic pressure 33% value below predicted failure. The vessel with the inverted pyramid joint failed in the wall acreage at a hydrostatic pressure within 10% of the actual failure pressure.

Verhage, Joseph M.↗

NASA NTRS2002

Buckling Design Studies of Inverted, Oblate Bulkheads for a Propellant Tank

An investigation of the deformation and buckling characteristics of a composite, oblate bulkhead that has an inverted geometry and is subjected to pressure-only loading is presented for three bulkhead geometries and thicknesses. The effects of a stiffening support ring at the bulkhead to cylinder interface are also evaluated. Buckling analyses conducted using the axisymmetric shell code BOSOR4 are discussed for several bulkhead configurations. These results are analytically verified using results from the Structural Analysis of General Shells (STAGS) code for a selected bulkhead configuration. The buckling characterization of an inverted, oblate bulkhead requires careful attention as small changes in bulkhead parameters can have a significant effect on the critical buckling load. Comparison of BOSOR4 and STAGS results provided a very good correlation between the two analysis methods. In addition, the analysis code BOSOR4 was found to be an efficient sizing tool that is useful during the preliminary design stage of a practical shell structure. Together, these two aspects should give the design engineer confidence in sizing these stability critical structures. Additional characterization is warranted, especially for a composite tank structure, since only one bulkhead configuration was examined closely.

Smeltzer, Stanley S., III↗

NASA NTRS2000

Power supply circuit for an ion engine sequentially operated power inverters

A power supply circuit for an ion engine suitable for a spacecraft has a voltage bus having input line and a return line. The power supply circuit includes a pulse width modulation circuit. A plurality of bridge inverter circuits is coupled to the bus and the pulse width modulation circuit. The pulse width modulation circuit generates operating signals having a variable duty cycle. Each bridge inverter has a primary winding and a secondary winding. Each secondary winding is coupled to a rectifier bridge. Each secondary winding is coupled in series with another of the plurality of rectifier bridges.

Cardwell, Jr., Gilbert I.↗

NASA NTRS2020

Machine Learning for Dynamical Modeling of a Flexible Inverted Pendulum System

The inverted pendulum system, a canonical example of an unstable mechanical system, is often used to model the control problems encountered in the flight of rockets in the initial stages of launch, when the airspeed is too small for aerodynamic stability. A system with a flexible pendulum is a variant that more accurately simulates rocket flight nonlinearities (particularly, the flex modes of the rocket). To increase NASA capability of modeling dynamical systems for which closed form solutions are not clear or easily developed, this project aims to provide a machine learning approach that produces a learned dynamical model of the PENNY robot (a rover with a flexible inverted pendulum) from operational data. The developed approach can then be generalized to other complex dynamical systems, including but not limited to rockets and other robotic systems.

M. A. DuPuis↗

DOE OSTI2020

Inverted organic photosensitive devices

The present disclosure relates to organic photosensitive optoelectronic devices grown in an inverted manner. An inverted organic photosensitive optoelectronic device of the present disclosure comprises a reflective electrode, an organic donor-acceptor heterojunction over the reflective electrode, and a transparent electrode on top of the donor-acceptor heterojunction.

14 SOLAR ENERGY↗

DOE OSTI2020

Optimal PV Inverter Control in Distribution Systems via Data-Driven Distributionally Robust Optimization

Distribution systems with high penetration of uncertain solar generation call for advanced control strategies of photovoltaics (PVs) inverters. This paper proposes a data-driven distributionally robust optimization (DDDRO) approach to optimally controlling the PV inverters to improve the system operation performance under solar power uncertainties. In the proposed DDDRO approach, a Wasserstein ball-based method is proposed to construct the distributional ambiguity set to model the uncertainties of PV generation through partial observations of historical data without knowing exact probability distributions. We further reformulate the computationally intractable DDDRO model to a mixed integer second order cone programming (MISOCP) problem. The effectiveness and out-of-sample performance of the proposed approach have been demonstrated on a modified IEEE 33-node system. We conduct a comparative study to compare the proposed method with traditional chance constrained programming (CCP). It shows that the proposed DDDRO approach can provide a less conservative yet robust solution to minimize the worse-case expectation of the total network loss while maintaining nodal voltages in a secure range.

Xue, Yaosuo↗

DOE OSTI2021

PRECISE™ PREconfiguring and Controlling Inverter SEt-points: A Solution for Easy Solar Integration

PRECISE™ is a software solution for preconfiguring solar inverter settings. It can be used by utilities and system operators to efficiently process new inverter applications at much less the time and effort, and with greater precision for settings that optimize stability and energy savings. PRECISE has received an R&D 100 award, and has been used to dramatically cut wait times and labor costs for new residential solar installations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗