Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Heat conduction modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Coronal plasma parameters in a long-duration X-ray event observed by Skylab

Physical conditions in the solar coronal X-ray-emitting plasma are analyzed for an event observed by the S-056 X-ray telescope on Skylab in August 1973. The event was located at the west limb and consisted of a series of high looplike structures that underwent dramatic changes in structure and intensity for more than 50 hours. A total X-ray energy (8 to 20 A) of about 5 by 10 to the 28th power erg is obtained by integrating over the lifetime and is shown to be equivalent to that reported previously for a 'typical' flare. It is found that a first major peak in total X-ray flux and thermal energy density was due to an increase in temperature, a major secondary peak in these parameters corresponded to the time of maximum in density, and conductivity energy losses near maximum intensity were much greater than radiative losses. Models dealing with sources of heating and energy balance are evaluated.

Vorpahl, J. A.↗
NASA NTRS1980

X-ray emission from the winds of hot stars

A phenomenological theory is proposed for the structure of the unstable line-driven winds of early-type stars. These winds are conjectured to break up into a population of blobs that are being radiatively driven through, and confined by ram pressure of an ambient gas that is not itself being radiatively driven. Radiation from the bow shocks preceding the blobs can account for the X-ray luminosity of zeta Puppis. The theory breaks down when used to model the much lower density wind of tau Scorpii, for then the blobs are destroyed by heat conduction from shocked gas. This effect explains why the profiles of this star's UV resonance lines depart from classical P Cygni form.

Lucy, L. B.↗
NASA NTRS1984

Preliminary results of a study of the relationship between free stream turbulence and stagnation region heat transfer

The mechanism that causes free stream turbulence to increase heat transfer in the stagnation region of turbine vanes and blades was studied. The work is being conducted in a wind tunnel at atmospheric conditions to facilitate measurements of turbulence and heat transfer. The model size is scaled up to simulate Reynolds numbers (based on leading edge diameter) that are to be expected on a turbine blade leading edge. Reynolds numbers from 13,000 to 177,000 were run in the present tests. Spanwise averaged heat transfer measurement with high and low turbulence were made with rough and smooth surface stagnation regions. Results of these measurements show that the boundary layer remains laminar in character even in the presence of free stream turbulence at the Reynolds numbers tested. If roughness is added the boundary layer becomes transitional as evidenced by the heat transfer increase with increasing distance from the stagnation line. Hot wire measurements near the stagnation region downstream of an array of parallel wires has shown that vorticity in the form of mean velocity gradients is amplified as flow approaches the stagnation region.

Vaanfossen, G. J., Jr.↗
NASA NTRS1985

Preliminary results of a study of the relationship between free stream turbulence and stagnation region heat transfer

The mechanism that causes free stream turbulence to increase heat transfer in the stagnation region of turbine vanes and blades was studied. The work is being conducted in a wind tunnel at atmospheric conditions to facilitate measurements of turbulence and heat transfer. The model size is scaled up to simulate Reynolds numbers (based on leading edge diameter) that are to be expected on a turbine blade leading edge. Reynolds numbers from 13,000 to 177,000 were run in the present tests. Spanwise averaged heat transfer measurement with high and low turbulence were made with rough and smooth surface stagnation regions. Results of these measurements show that the boundary layer remains laminar in character even in the presence of free stream turbulence at the Reynolds numbers tested. If roughness is added the boundary layer becomes transitional as evidenced by the heat transfer increase with increasing distance from the stagnation line. Hot wire measurements near the stagnation region downstream of an array of parallel wires have shown that vorticity in the form of mean velocity gradients is amplified as flow approaches the stagnation region.

Vanfossen, G. J., Jr.↗
NASA NTRS1986

Laser anemometry measurements of natural circulation flow in a scale model PWR reactor system

The natural circulation of a single phase fluid in a scale model of a pressurized water reactor system during a postulated grade core accident is analyzed. The fluids utilized were water and SF6. The design of the reactor model and the similitude requirements are described. Four LDA tests were conducted: water with 28 kW of heat in the simulated core, with and without the participation of simulated steam generators; water with 28 kW of heat in the simulated core, with the participation of simulated steam generators and with cold upflow of 12 lbm/min from the lower plenum; and SF6 with 0.9 kW of heat in the simulated core and without the participation of the simulated steam generators. For the water tests, the velocity of the water in the center of the core increases with vertical height and continues to increase in the upper plenum. For SF6, it is observed that the velocities are an order of magnitude higher than those of water; however, the velocity patterns are similar.

Kadambi, J. R.↗
NASA NTRS1987

The normal modes of the thermosphere

The linearized momentum, energy, and continuity equations for the thermosphere can be reduced to a form that gives the vertical structure for each horizontal wave mode. The vertical structure equation can be described in terms of the normal modes, or eigenmodes, of the thermosphere. The latter are obtained by using a 27-layer model that includes a realistic temperature profile and the effects of the Lorentz force, viscosity, and heat conduction. The normal modes have one real eigenfrequency for every two complex conjugate eigenfrequency values. The real modes have a dominant rotational wind component and are nonpropagating. The complex modes have comparable divergent and rotational wind components. The complex eigenvalues give vertically propagating modes, primarily associated with the transient response to forcing, and are significantly affected by the dissipation in the upper E region and F region. Results show that the rotational wind component dominates in the steady state when the forcing is due to the two-cell convection pattern at high latitudes and that the normal modes explain the large shears and large winds speeds that are typically observed in the high-latitude E region. The vertical energy flux for the normal modes is also calculated. The results show that the flux is upward above 130 km but downward in the lower E region for the total solution. The downward energy flux is a contribution from the real eigenmode structure.

Larsen, M. F.↗
NASA NTRS1988

An analysis of the response of the thermospheric normal modes to temporally varying convection at high latitudes

The response of the high-latitude thermosphere to temporal variations in the forcing due to the plasma convection pattern is investigated using a normal modes model that includes realistic temperature and electron density profiles as well as the effects of viscosity, heat conduction, and Lorentz forcing. The calculations show that the rotational wind component is only slightly modified when the plasma rotation is varied, while the divergent wind component responds more strongly to variations of the rotation rate, with the effect being greatest in the E region. A variation of the rotation rate then results in a greater magnitude and phase variation with the height of the divergent wind component in the E region, indicating that vertically propagating gravity waves are of importance in that height range.

Clark, M. A.↗
NASA NTRS1989

Test Data of Flow Field of Shuttle SRM Nozzle Joint with Bond Defects, Using Unheated Air

The nozzle-to-case joint on the Shuttle SRM (as redesigned after the Challenger accident) features an adhesive sealant filling and bonding the joint, with a wiper O-ring to prevent the adhesive from reaching and disabling the closure O-ring. Flawless implementation of that joint design would ensure that hot, corrosive propellant combustion gases never reach the closure O-ring. However, understanding the flow field related to bonding defects is prudent. A comprehensive test program was conducted to quantify such flow fields and associated heating environments. A two-dimensional, full-scale model represented 65 inches of the nozzle joint, using unheated air as the test medium, in a blowdown mode. Geometry variations modeled RSRM assembly tolerances, and two types of bonding defects: pullaways and blowholes. A range of the magnitude of each type defect was tested. Also a range of operational parameters was tested, representative of the RSRM flow environment, including duplication of RSRM Mach and Reynolds numbers. Extensive instrumentation was provided to quantify pressures, heat rates, and velocities. The resulting data established that larger geometric defects cause larger pressure and larger heating, at the closure O-ring region. Velocity trends were not so straight-forward. Variations in assembly tolerances did not generally affect flow fields or heating. Operational parameters affected flow fields and heating as might be expected, increasing density or velocity increased heating. Complete details of this test effort are presented.

Hair, Leroy M.↗
NASA NTRS1990

Transient analysis of a capillary pumped loop heat pipe

A bench-top Capillary Pumped Loop (CPL) test system has been developed and tested to investigate the transient mode operation of this system by applying a step power input to the evaporators. Tests were conducted at several power input and evaporator inlet subcooling combinations. In addition, a lumped-heat-capacity model of the CPL test system has been presented which is used for predicting qualitatively the transient operation characteristics. Good agreement has been obtained between the predicted and the measured temperature variations. A simple evaporator inlet subcooler model has also been developed to study effects of inlet subcooling on the steady-state evaporator wall temperature. Results were compared with the test data collected.

Kiper, A. M.↗
NASA NTRS1990

The Personnel Launch System

NASA has begun to study candidate vehicles for manned access to space in support of the Space Station or other future missions requiring on-demand transportation of people to and from earth orbit. One such system, which would be used to complement the present Shuttle or an upgraded version, is the Personnel Launch System (PLS), which is envisioned as a reusable priority vehicle to place people and small payloads into orbit using an experimental launch vehicle. The design of the PLS is based on a Space Station crew changeout requirement whereby eight passengers and two crew members are flown to the station and a like number are returned within a 72 hour mission duration. Experimental and computational aerothermodynamic heating studies have been conducted using a new two-color thermographic technique that involved coating the model with a phosphor that radiates at varying color intensities as a function of temperature when illuminated with UV light. A full-scale model, the HL-20, has been produced and will be used for man-machine research. Three launch vehicle concepts are being considered, a Titan IV, the Advanced Launch System, and a Shuttle equipped with liquid rocket boosters.

Piland, William M.↗
NASA NTRS1993

Active Thermal Isolation For Hot-Film Anemometers

Local heating compensates for conduction of heat from sensors into modules. Two hot-film sensors stacked on wind-tunnel model. Outer sensor detects changes in boundary-layer flow. Inner sensor provides active thermal isolation between outer sensor and model. Thermal boundary condition controlled at response time of detection hot-film sensor, significantly less than response time of internally heated model. Requires less power to maintain outer hot-film sensor at given temperature, enabling system to respond over greater dynamic range before power limits of instrument reached. Stacked sensors bonded to surface of most wind-tunnel models, even to curved surfaces, and removed after completion of experiments.

Martinson, Scott D.↗
NASA NTRS1999

Short Duration Base Heating Test Improvements

Significant improvements have been made to a short duration space launch vehicle base heating test technique. This technique was first developed during the 1960's to investigate launch vehicle plume induced convective environments. Recent improvements include the use of coiled nitrogen buffer gas lines upstream of the hydrogen / oxygen propellant charge tubes, fast acting solenoid valves, stand alone gas delivery and data acquisition systems, and an integrated model design code. Technique improvements were successfully demonstrated during a 2.25% scale X-33 base heating test conducted in the NASA/MSFC Nozzle Test Facility in early 1999. Cost savings of approximately an order of magnitude over previous tests were realized due in large part to these improvements.

Bender, Robert L.↗
NASA NTRS1995

Aerothermal/FEM Analysis of Hypersonic Sharp Leading Edges

Advanced hypersonic vehicles, like wave riders, will have sharp leading edges to minimize drag. These designs require accurate finite element modeling (FEM) of the thermal-structural behavior of a diboride ceramic matrix composite sharp leading edge. By coupling the FEM solver to an engineering model of the aerothermodynamic heating environment the impact of non catalytic surfaces, rarefied flow effects, and multidimensional conduction on the performance envelopes of sharp leading edges can be examined.

Kolodziej, Paul↗
NASA NTRS2007

Pad B Liquid Hydrogen Storage Tank

Kennedy Space Center is home to two liquid hydrogen storage tanks, one at each launch pad of Launch Complex 39. The liquid hydrogen storage tank at Launch Pad B has a significantly higher boil off rate that the liquid hydrogen storage tank at Launch Pad A. This research looks at various calculations concerning the at Launch Pad B in an attempt to develop a solution to the excess boil off rate. We will look at Perlite levels inside the tank, Boil off rates, conductive heat transfer, and radiant heat transfer through the tank. As a conclusion to the research, we will model the effects of placing an external insulation to the tank in order to reduce the boil off rate and increase the economic efficiency of the liquid hydrogen storage tanks.

Hall, Felicia↗
NASA NTRS2016

Parametric Characterization of TES Detectors Under DC Bias

The X-ray integrated field unit (X-IFU) in European Space Agency's (ESA's) Athena mission will be the first high-resolution X-ray spectrometer in space using a large-format transition-edge sensor microcalorimeter array. Motivated by optimization of detector performance for X-IFU, we have conducted an extensive campaign of parametric characterization on transition-edge sensor (TES) detectors with nominal geometries and physical properties in order to establish sensitivity trends relative to magnetic field, dc bias on detectors, operating temperature, and to improve our understanding of detector behavior relative to its fundamental properties such as thermal conductivity, heat capacity, and transition temperature. These results were used for validation of a simple linear detector model in which a small perturbation can be introduced to one or multiple parameters to estimate the error budget for X-IFU. We will show here results of our parametric characterization of TES detectors and briefly discuss the comparison with the TES model.

X-ray Integral Field↗
NASA NTRS2011

Dual Heat Pulse, Dual Layer Thermal Protection System Sizing Analysis and Trade Studies for Human Mars Entry Descent and Landing

NASA has been recently updating design reference missions for the human exploration of Mars and evaluating the technology investments required to do so. The first of these started in January 2007 and developed the Mars Design Reference Architecture 5.0 (DRA5). As part of DRA5, Thermal Protection System (TPS) sizing analysis was performed on a mid L/D rigid aeroshell undergoing a dual heat pulse (aerocapture and atmospheric entry) trajectory. The DRA5 TPS subteam determined that using traditional monolithic ablator systems would be mass expensive. They proposed a new dual-layer TPS concept utilizing an ablator atop a low thermal conductivity insulative substrate to address the issue. Using existing thermal response models for an ablator and insulative tile, preliminary hand analysis of the dual layer concept at a few key heating points indicated that the concept showed potential to reduce TPS masses and warranted further study. In FY09, the followon Entry, Descent and Landing Systems Analysis (EDL-SA) project continued by focusing on Exploration-class cargo or crewed missions requiring 10 to 50 metric tons of landed payload. The TPS subteam advanced the preliminary dual-layer TPS analysis by developing a new process and updated TPS sizing code to rapidly evaluate mass-optimized, full body sizing for a dual layer TPS that is capable of dual heat pulse performance. This paper describes the process and presents the results of the EDL-SA FY09 dual-layer TPS analyses on the rigid mid L/D aeroshell. Additionally, several trade studies were conducted with the sizing code to evaluate the impact of various design factors, assumptions and margins.

McGuire, Mary Kathleen↗
NASA NTRS1991

Cosmic-ray heating of cooling flows - A critical analysis

It is shown that a combination of MHD wave-mediated cosmic ray heating and thermal conduction could balance cooling in intracluster media and substantially reduce the rate of inflow. The appropriate system of steady state equations is solved, including a new self-consistent formulation for the cosmic-ray diffusivity. Models which can produce substantial positive temperature gradients in static configurations are found when conduction is reduced by a factor of 10 or more. These models have too-flat thermal pressure profiles compared with observations. It is found that cosmic-ray heating is unlikely either to stabilize positive density perturbations against condensation or to contribute appreciably to the powering of the optical filaments.

Loewenstein, Michael↗