Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “GAS MIXTURE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

An experimental and kinetic modeling study of NO x sensitization on methane autoignition and oxidation

An experimental and kinetic modeling study of the influence of NO x (i.e. NO 2 , NO and N 2 O) addition on the ignition behavior of methane/‘air’ mixtures is performed. Ignition delay time measurements are taken in a rapid compression machine (RCM) and in a shock tube (ST) at temperatures and pressures ranging from 900–1500 K and 1.5–3.0 MPa, respectively for equivalence ratios of 0.5–2.0 in ‘air’. The conditions chosen are relevant to spark ignition and homogeneous charge compression ignition engine operating conditions where exhaust gas recirculation can potentially add NO x to the premixed charge. The RCM measurements show that the addition of 200 ppm NO 2 to the stoichiometric CH 4 /oxidizer mixture results in a factor of three increase in reactivity compared to the baseline case without NOx for temperatures in the range 600–1000 K. However, adding up to 1000 ppm N 2 O does not show any appreciable effect on the measurements. The promoting effect of NO 2 was found to increase with temperature in the range 950–1150 K, while the sensitization effect decreases at higher pressures. The experimental results measured are simulated using NUIGMech1.2 comprising an updated NO x sub-chemistry in this work. A kinetic analysis indicates that the competition between the reactions ĊH 3 + NO 2 ↔ CH 3 Ȯ + NO and ĊH 3 + NO 2 (+M) ↔ CH 3 NO 2 (+M), the former being a propagation reaction and the latter being a termination reaction governs NO x sensitization on CH 4 ignition. Recent calculations by Matsugi and Shiina (A. Matsugi, H. Shiina, J. Phys. Chem. A. 121 (2017) 4218–4224) for the nitromethane formation reaction CH 3 + NO 2 (+M) ↔ CH 3 NO 2 (+M), together with the recently calculated rate constants for HONO/HNO 2 reactions significantly improve ignition delay time predictions in the temperature range 600–1000 K. Furthermore, the experiments with NO addition reveal a non-monotonous sensitization impact on CH 4 ignition at lower temperatures with NO initially acting as an inhibitor at low NO concentrations and then as a promoter as NO concentrations increase in the mixture. This non-monotonous trend is attributed to the role of the chain-termination reaction ĊH 3 + NO 2 (+M) ↔ CH 3 NO 2 (+M) and the impact of NO on the transition to the chain-branching steps CH 2 O + HȮ 2 ↔ HĊO + H 2 O 2 , H 2 O 2 (+M) ↔ ȮH + ȮH (+M), HĊO ↔ CO + Ḣ followed by CO + O 2 ↔ CO 2 + Ö and Ḣ + O 2 ↔ Ö + ȮH. NUIGMech1.2 is systematically validated against the new ignition delay measurements taken here together with species measurements and high temperature ignition delay time data available in the literature for CH 4 /oxidizer mixtures diluted with NO 2 /N 2 O/NO and is observed to accurately capture the sensitization trends.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Mechanistic Similarities and Differences for Hydrogenation of Aromatic Heterocycles and Aliphatic Carbonyls on Sulfided Ru Nanoparticles

This study establishes the contrasting reactivity trends for the hydrogenation of aromatic hydrocarbons (AHCs = C n H m X, X = N, S, O, and C) and aliphatic carbonyls [R a C(O)R b ; R a = alkyl group, R b = CH 3 or H] on sulfided Ru clusters arising from the difference in the elementary proton and hydride attack catalytic sequence. Both reactions require sequential additions of a proton from either Ru n+ –(SH 2 ) or S 2 –(H δ+ ) species and a hydride from Ru n+ –(H δ– ) species to the unsaturated C=X bonds. For the five-membered-ring aromatic heterocycles (AHCs = pyrrole, thiophene, and furan), an initial proton addition limits the catalytic turnovers; thus, their hydrogenation reactivity increases with increasing gas-phase proton affinities of the AHCs. Pyridine as the more basic six-membered N-AHC is more susceptible to protonation; therefore, it is more reactive, and its initial proton addition is quasi-equilibrated, followed by the kinetically relevant hydride addition. Conversely, aliphatic carbonyls prefer to undergo hydrogen additions in a reverse sequence, where a Ru n+ –(H δ– ) hydride initially attacks the electron-deficient carbonyl C atom as the kinetically relevant step before a subsequent rapid S 2 –(H δ+ ) proton addition on the electron-rich O atom, as confirmed by isotopic exchange studies with butanal-D 2 and 1-butanol-D 2 mixtures and density functional theory calculations on S-deficient RuS 2 (100) surfaces. For these reasons, their hydrogenation reactivity increases with increasing gas-phase hydride affinities of the carbonyls. On metallic Ru surfaces without sulfur, hydrogen adatoms (H*) are the only reactive hydrogen species; the reactivity of their attack on aromatic heterocycles increases with increasing reactant proton affinities much more sensitively than that on sulfided Ru surfaces. This work illustrates the distinct catalytic roles of the diverse hydrogen species in hydrogenation—the interplay between proton and hydride additions has marked catalytic consequences in shaping the free energy landscape of the reactions, which in turn leads to the observed kinetic dependences, kinetic parameters, reactivity trends, and scaling relations between the measured barriers and the appropriate kinetic descriptors, that is, proton affinity of AHCs and hydride affinity of carbonyls in hydrogenation catalysis. Here, these mechanistic similarities and differences provide explanations of the observed reactivity trends and thus have profound implications for industrial hydrogenation and hydrotreating catalysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Visualizing Size-Dependent Dynamics of CeO 2-δ {100}-Supported CoO x Nanoparticles Under CO 2 Hydrogenation Conditions

Carbon dioxide is a major greenhouse gas. In order to optimize processes focused on its chemical valorization, one needs detailed information about the effects of CO 2 and/or CO 2 /H 2 mixtures on the structure and morphology of metal/oxide catalysts. Here, in this study, the evolution of a catalyst with cobalt supported on CeO 2 -cube nanostructures under CO 2 hydrogenation conditions was investigated by using a set of in situ characterization techniques (X-ray absorption fine structure, X-ray diffraction, diffuse reflectance infrared Fourier transform spectroscopy, and environmental transmission electron microscopy (TEM)). The {100} facets of the ceria support displayed an unexpectedly high stability due to strong interactions with the aggregates of cobalt oxide. A significant influence of interfacial bonding between CoO x and CeO 2-δ {100} is evident through a clear preference in the orientation of CoO x nanoparticles (NPs) with respect to the substrate. For initially reduced Co/CeO 2 -cube nanostructures, a kinetically controlled oxidation of cobalt upon the introduction of CO 2 was observed during the early stages of CO 2 hydrogenation. Environmental TEM revealed the size-dependent morphological behavior of cobalt oxide NPs due to strong interactions with the CeO 2 {100} surface. When the environment was switched from H 2 to a mixture of H 2 and CO 2 at 250 °C, small CoO x NPs (in the largest dimension < 2.5 nm) rapidly transformed from a pyramidal three-dimensional (3D) form to a planar, monatomic layer attached to the concurrently oxidized CeO 2-δ {100} surface. This maximizes the number of sites available for the binding of CO 2 or reaction intermediates. The shape transformation reflected the oxophilic character of cobalt and strong metal–support interactions. The removal of CO 2 from the gas phase led to a reduction of the cobalt oxide NPs by hydrogen and a reversible two-dimensional → 3D transformation. In contrast, no significant morphological changes, apart from further oxidation, were observed for big CoO x NPs (in the largest dimension > 3 nm). These trends are not seen for nanoparticles of noble metals. The observed morphological and structural changes in the small CoO x NPs affected the stability of reaction intermediates and modified the selectivity of the CoO x /CeO 2 catalyst system for methane production.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Soot formation and precursor chemistry in Counterflow flames of aviation fuel surrogates

To meet market demands, the aviation sector is interested in utilizing drop-in Synthetic Aviation Turbine Fuels (SATF), either as neat fuels or in blends with conventional Jet A. SATF currently approved in standard specifications may have lower aromatic content with significant fractions of normal, branched, and cyclo-alkanes. Fundamental studies on soot formation from aviation fuels (Jet A, SATF) and their surrogate components are essential to understand how fuel composition influences soot and soot precursor formation. Here, this study reports new measurements of polycyclic aromatic hydrocarbons (PAH) and soot in counterflow diffusion flames (CDFs) of aviation fuel surrogates. Both intrusive and non-intrusive diagnostics are employed to determine the profiles of temperature, gas phase species, PAHs (up to C16), and soot volume fraction (SVF) in CDFs of iso-octane and surrogate mixtures. These measurements shed light on the transition of soot precursors to primary soot particles. In addition to serving as a common surrogate component in Jet A surrogate mixtures, iso-octane is a template species for larger, less volatile branched alkanes found in SATF mixtures. The newly developed Lawrence Livermore National Laboratory (LLNL) PAH and soot model successfully captures temperature, precursor species, and SVF profiles for the mixtures and conditions discussed in this work. Finally, a high-fidelity surrogate for Jet A is proposed that matches targeted physical and chemical properties well, while leveraging the wide range of candidate fuel molecules available in the LLNL detailed chemical model. The proposed surrogate formulation is validated against newly acquired measurements of the surrogate and literature measurements of Jet A. These new experiments and simulations provide critical insights into the PAH and soot formation from aviation fuels. Reaction pathways which require further investigation are highlighted, such that future work may bridge the remaining quantitative gaps in predicting soot formation from aviation fuel surrogates and surrogate components.

Aviation fuels↗
DOE OSTI2023

A Dual-Gated Structures for Lossless Ion Manipulations-Ion Mobility Orbitrap Mass Spectrometry Platform for Combined Ultra-High-Resolution Molecular Analysis

High-resolution ion mobility spectrometry-mass spectrometry (HR-IMS-MS) instruments have enormously advanced the ability to characterize complex biological mixtures. Unfortunately, HR-IMS and HR-MS measurements are typically performed independently due to mismatches in analysis time scales. Here we overcome this limitation by using a dual-gated ion injection approach to couple an 11-meter path length structures for lossless ion manipulations (SLIM) module to a Q-Exactive Plus Orbitrap MS. The dual-gate setup was implemented by placing one ion gate before the SLIM module and a second ion gate after. The dual-gated ion injection approach allowed the new SLIM-Orbitrap platform to simultaneously perform an 11-meter SLIM separation, Orbitrap mass analysis using the highest selectable mass resolution setting (up to 140k), and high-energy collision induced dissociation (HCD) in ~25 minutes over an $m/z$ range of ~1500 amu. The SLIM-Orbitrap was initially characterized using a mixture of standard phosphazene cations and demonstrated an average SLIM CCS resolving power (Rp CCS ) of ~218 and SLIM peak capacity of ~156 while simultaneously obtaining high mass resolutions. SLIM-Orbitrap analysis with fragmentation was then performed on mixtures of standard peptides and two reverse peptides (SDGRG 1+ , GRGDS 1+ , Rp CCS = 305) to demonstrate the utility of combined HR-IMS-MS/MS measurements for peptide identification. Our new HR-IMS-MS/MS capability was further demonstrated by analyzing a complex lipid mixture and showcasing SLIM separations on isobaric lipids. In conclusion, this new SLIM-Orbitrap platform demonstrates a critical new capability for proteomics and lipidomics applications, and the high-resolution multimodal data obtainable with this system establishes the foundation for reference-free identification of unknown ion structures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Lost Circulation Materials in Geothermal Drilling: Thermal Degradation, Viscosity, Compression, and Flow Loop Tests

This dataset provides a set of experimental data on the performance of lost circulation materials (LCMs) used in geothermal drilling operations. It includes results from four distinct tests: thermal degradation, viscosity measurements, compression tests, and high-temperature flow loop experiments. The materials tested, such as cedar fiber, cotton seed hulls, magma fiber, microcellulose, and sawdust, were analyzed under a range of conditions to assess their effectiveness in mitigating fluid losses in geothermal wells. Data on thermal degradation explores mass loss, water loss, and gas release for each material when subjected to temperatures between 90C and 250C. Viscosity measurements capture the behavior of LCM mixtures under different temperatures, while compression tests investigate the structural integrity of both undegraded and thermally degraded materials. The high-temperature flow loop experiments simulate geothermal well conditions, analyzing how different materials and mixtures affect fluid flow and sealing performance in a fractured reservoir environment. In addition to the experimental data, the dataset includes photos documenting the materials, schematics of test setups, and several published manuscripts that provide detailed insights into the experimental methods and findings.

15 GEOTHERMAL ENERGY↗
DOE OSTI2023

Simulation of a rapid compression machine for evaluation of ignition chemistry and soot formation using gasoline/ethanol blends

Due to the projected decline of demand for gasoline in light duty engines and the advent of ethanol as a green fuel, the use of gasoline/ethanol blend fuels in heavy duty applications are being investigated as they are projected to have lower cost and lower lifecycle green house gas (GHG) emissions. In heavy duty engines, the primary mode of combustion is mixing controlled combustion where wide range of mixture conditions (equivalence ratio) exist. Soot emissions of these fuels in richer conditions are not well understood. The goal of this research is to evaluate some commercially available soot modeling codes for the particulate matter emissions from gasoline/ethanol fuel blends, especially at fuel rich conditions. A Rapid Compression Machine (RCM) is modeled in a three-dimensional numerical simulation using CONVERGE computational software using a reduced chemical kinetic mechanism with SAGE chemistry solver and a RANS k-ϵturbulence model with a sector model including the creviced piston. The creviced piston is used in the experimental setup to reduce boundary layer effects and to maintain a homogeneous core in the reaction cylinder. Computational fluid dynamics simulations are conducted for different gasoline-ethanol fuel blends from E10 (10% ethanol v/v) to E100. The fuel blend is modeled as a surrogate mixture of toluene, iso-octane, n-heptane for gasoline content, and ethanol. The computational results were validated against experimental results using pressure measurements and laser extinction diagnostics. Different soot models are investigated to evaluate their capability of predicting the sooting tendencies of fuel blends, especially in richer conditions experienced during mixing-controlled combustion. The experimental combustion characteristics such as the ignition delay of different blends of fuel are reasonably well predicted. The Particulate Size Mimic (PSM) model accurately predicts the soot generation characteristics of the different fuels, but the Hiroyasu-NSC model falls short in this regard. For accurate prediction of soot with the PSM model, the thermodynamic conditions during combustion must be accurately modeled. While the current computational modeling tools can produce accurate results for the prediction of particulate matter emissions, there is much work to be done in improving our understanding of the underlying fundamental processes.

Energy & Fuels↗
DOE OSTI2020

Heteroatom-doped porous carbons for clean energy applications and methods for their synthesis

Methods for a facile, template free and one-step synthesis of nanoporous carbons by using a heterocyclic aromatic organic compound as a single source precursor of both carbon and nitrogen are described. The heterocyclic aromatic organic compound contains nitrogen in pyrrolic and/or pyridinic positions and is chemically activated with NaOH, KOH or ZnCl2 at high temperatures in a solid state mixture as a synthesis protocol to promote fine micropores during carbonization. Nanoporous carbons synthesized by these methods that have superior gas sorption/storage and energy storage properties are also described. The nanoporous carbons are useful as carbon sequestration agents and supercapacitors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

High speed PLIF study of the Richtmyer–Meshkov instability upon re-shock

The Richtmyer–Meshkov instability (RMI) of a twice-shocked gas interface is researched using high-speed planar-laser induced fluorescence (PLIF) in the Wisconsin Shock Tube Laboratory’s vertical shock tube. The initial condition (IC) is a shear layer with broadband diffuse perturbations at the interface between a helium-acetone mixture and argon. This IC is accelerated by a shock of nominal strength M = 1.8, and then accelerated again by the transmitted shock that reflects off the end wall of the tube. An estimate of the light gas mole fraction is extracted from high-speed imaging using an iterative process that accounts for the nonlinear temperature dependence of the acetone’s fluorescence quantum yield (FQY) and absorption cross-section. A vorticity deposition model for the initial growth rate after reshock is compared with the Mikaelian model for re-shock. Previously used in literature, the number of generations is shown to naturally arise from a normalisation of the scalar transport equation. A self-similar analysis is then further performed using the mole fraction data to explore the evolution of the RMI after reshock and the higher order moments of the light gas mole fraction are compared with a proposed model.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Influence of pilot-fuel mixing on the spatio-temporal progression of two-stage autoignition of diesel-sprays in low-reactivity ambient fuel-air mixture

The spatial and temporal locations of autoignition for direct-injection compression-ignition engines depend on fuel chemistry, temperature, pressure, and mixing trajectories in the fuel jets. Dual-fuel systems can provide insight into both fuel-chemistry and physical effects by varying fuel reactivities and engine operating conditions. In this context, the spatial and temporal progression of two-stage autoignition of a diesel-fuel surrogate, n-heptane, in a lean-premixed charge of synthetic natural-gas (NG) and air is imaged in an optically accessible heavy-duty diesel engine. The lean-premixed charge of NG is prepared by fumigation upstream of the engine intake manifold. Optical diagnostics include high-speed (15kfps) cool-flame chemiluminescence-imaging as an indicator of low-temperature heat-release (LTHR) and OH* chemiluminescence-imaging as an indicator high-temperature heat-release (HTHR). NG prolongs the ignition delay of the pilot fuel and increases the combustion duration. Zero-dimensional chemical-kinetics simulations provide further understanding by replicating a Lagrangian perspective for mixtures evolving along streamlines originating either at the fuel nozzle or in the ambient gas, for which the pilot-fuel concentration is either decreasing or increasing, respectively. The zero-dimensional simulations predict that LTHR initiates most likely on the air streamlines before transitioning to HTHR, either on fuel-streamlines or on air-streamlines in regions of near-constant φ. Due to the relatively short pilot-fuel injection-durations, the transient increase in entrainment near the end of injection (entrainment wave) is important for quickly creating auto-ignitable mixtures. To achieve desired combustion characteristics, e.g., multiple ignition-kernels and favorable combustion phasing and location (e.g., for reducing wall heat-transfer or optimizing charge stratification), adjusting injection parameters could tailor mixing trajectories to offset changes in fuel ignition chemistry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Comprehensive two-dimensional gas chromatography under low-pressure conditions

The analysis of thermally labile and high-boiling point compounds by gas chromatography (GC) can be a challenge. One technique to overcome these challenges is low-pressure GC, which uses the vacuum produced from the mass spectrometer and wide-bore columns to elute compounds at significantly lower temperatures. While GC-MS is a powerful technique, comprehensive two-dimensional gas chromatography (GC × GC), allows for resolution of compounds that would typically coelute using GC. Here, in this study, a pesticide standard mixture (8270 MegaMix Standard) was analyzed using a conventional GC × GC-TOFMS configuration (0.25 mm inner diameter (i.d.) to a 0.18 mm i.d. column) and low-pressure GC × GC-TOFMS configuration (0.53 mm i.d. to a 0.53 mm i.d. column). Elution temperatures, sensitivity, and peak capacity were investigated for both configurations. Compounds eluted an average of 30 °C less on the low-pressure GC × GC-TOFMS configuration compared to the conventional GC × GC-TOFMS configuration. Moreover, the compounds were separated in ~13 min on the low-pressure GC × GC-TOFMS as opposed to 33 min for conventional GC × GC-TOFMS. However, due to the wide-bore columns and faster runtimes the low-pressure GC × GC-TOFMS had a lower, β corrected 2D peak capacity, n c,β,2D , of 1260 while the conventional GC × GC-TOFMS was 3588. Interestingly, both configurations yielded a similar peak capacity production of 93 peaks/min and 107 peaks/min for low-pressure and conventional GC × GC-TOFMS, respectively. A “real world” sample of diesel fuel was tested on the low-pressure and conventional GC × GC-TOFMS configurations and similar results were obtained compared to the pesticide standard mix except the peak capacity production of the low-pressure GC × GC-TOFMS configuration was higher than that of the conventional GC × GC-TOFMS method.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

An experimental investigation of flame and autoignition behavior of propane

We report autoignition delay time data are one important means to develop, quantify, and validate fundamental understanding of combustion chemistry at low temperatures (T<1200 K). However, low-temperature chemistry often has higher uncertainties and scatter in the experimental data compared with high-temperature ignition data (T>1200 K). In this study, autoignition properties of propane and oxygen mixtures were investigated using the University of Michigan rapid compression facility in order to understand the effects of ignition regimes on low-temperature ignition data. For the first time for propane, autoignition delay times were determined from pressure histories, and autoignition characteristics were simultaneously recorded using highspeed imaging of the test section through a transparent end-wall. Propane mixtures with fuel-to-O 2 equivalence ratios of φ = 0.25 and φ = 0.5 and O 2 -to-inert gas molar ratios of 1:3.76 were studied over the pressure range of 8.9 to 11.3 atm and the temperature range of 930 – 1070 K. The results showed homogeneous or strong autoignition occurred for all φ = 0.25 experiments, and inhomogeneous or mixed autoignition occurred for all φ = 0.5 experiments. While a limited temperature range is covered in the study, importantly the data span predicted transitions in autoignition behavior, allowing validation of autoignition regime hypotheses. Specifically, the results agree well with strong-autoignition limits proposed based on the Sankaran Criterion. The autoignition delay time data at the strong-ignition conditions are in excellent agreement with predictions using a well-validated detailed reaction mechanism from the literature and a zerodimensional modeling assumption. However, the experimental data at the mixed autoignition conditions were systematically faster than the model predictions, particularly at lower temperatures (T< ~970 K). The results are an important addition to the growing body of data in the literature that show mixed autoignition phenomena are important sources of the higher scatter observed in the low-temperature autoignition data for propane and other fuels. The results are discussed in terms of different methods to capture the effects of pre-autoignition heat release associated with mixed autoignition conditions and thereby address some of the discrepancies between kinetic modeling and experimental measurements.

42 ENGINEERING↗
DOE OSTI2022

Theoretical Pathway toward Improved Reverse Osmosis Membrane Selectivity for Neutral Solutes: Inspiration from Gas Separations

We report highly rigid membrane materials with tailored structures have exhibited permeabilities and selectivities that exceed the polymer upper bound in gaseous and organic solvent separations for challenging mixtures containing species that are similar in size and shape. One potential question is whether such membrane materials can maintain meaningful guest diffusivities in situations where the microporous spaces are essentially full of guest molecules. Here, we use a simplified transition state theory approach to estimate the diffusivity of water and small organics within a microporous membrane. The transition state theory model is parameterized using experimental values from zeolites and carbon molecular sieve materials found in the literature. We demonstrate the differences in transport and Maxwell–Stefan diffusivities based on guest species loading with different isotherm behaviors. These calculations theorize a path forward for highly selective reverse osmosis membranes for aqueous phase separations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

CO Laser Absorption Measurements During Syngas Combustion at High Pressure

Abstract Syngas is a desirable fuel for combustion in the Allam-Fetvedt cycle, which involves combustion under supercritical-CO2 conditions. While some work has been conducted in collecting ignition delay times (IDT) at the extreme pressures required by these systems, significant model deficiencies remain. Additionally, considerable barriers in terms of nonideal gas dynamic effects have been shown for these experiments in shock tubes. Further investigation into the fundamental combustion kinetics of H2/CO/CO2 mixtures is required. Time-resolved speciation measurements for target species have been shown to better aid in improving the understanding of underlying chemical kinetics than global ignition delay time measurements. Therefore, laser absorption measurements of CO were measured behind reflected shock waves during combustion of syngas at 5 and 10 bar and temperatures between 1080 and 2100 K. The mixtures investigated utilized H2-to-CO ratios of 1:1 and 1:4, respectively, each at stoichiometric conditions, allowing for discussions of the effect of initial fuel composition. A ratio of fuel to CO2 of 1:2 was also utilized to represent commercially available syngas. The mixtures were diluted in helium and argon (20% He, 76.5% Ar) to minimize thermal effects and to expedite CO thermal relaxation during the experiment. The resulting CO time histories were then compared to modern chemical kinetics mechanisms, and disagreement is seen for this system, which is assumed to be fairly well known. This study elucidates particular chemistry that needs improvement in moving toward a better understanding of syngas combustion at elevated pressures.

Engineering↗
DOE OSTI2024

Adsorption of Natural Gas in Metal–Organic Frameworks: Selectivity, Cyclability, and Comparison to Methane Adsorption

Evaluation of metal–organic frameworks (MOFs) for adsorbed natural gas (ANG) technology employs pure methane as a surrogate for natural gas (NG). This approximation is problematic, as it ignores the impact of other heavier hydrocarbons present in NG, such as ethane and propane, which generally have more favorable adsorption interactions with MOFs compared to methane. Herein, using quantitative Raman spectroscopic analysis and Monte Carlo calculations, we demonstrate the adsorption selectivity of high-performing MOFs, such as MOF-5, MOF-177, and SNU-70, for a methane and ethane mixture (95:5) that mimics the composition of NG. The impact of selectivity on the storage and deliverable capacities of these adsorbents during successive cycles of adsorption and desorption, simulating the filling and emptying of an ANG tank, is also demonstrated. Finally, the study reveals a gradual reduction in the storage performance of MOFs, particularly with smaller pore volumes, due to ethane accumulation over long-term cycling, until a steady state is reached with substantially degraded storage performance.

03 NATURAL GAS↗
DOE OSTI2020

A detailed chemical kinetic modeling and experimental investigation of the low- and high-temperature chemistry of n-butylcyclohexane

Chemical kinetic models of gasoline, jet, and diesel fuels and their mixtures with bioderived fuels are needed to assess fuel property effects on efficiency, emissions, and other performance metrics in internal combustion and gas turbine engines. As these real fuels have too many fuel components to be included in a chemical kinetic model, surrogate fuels containing fewer components are used to represent them. These surrogate fuels mimic the chemical classes or molecular structures contained in the real fuel. One of the important chemical classes in gasoline, jet, and diesel fuels comprises cyclohexanes. Cyclohexanes comprise about 30% or more by weight in diesel fuel. Also, Mueller et al proposed n-butylcyclohexane (nBCH) as a component in a nine-component surrogate palette to represent the ignition properties, distillation curve, density, and molecular structures of a diesel certification fuel. Herein, experimental measurements of the ignition delay times (IDTs) of nBCH in a shock tube and in a rapid compression machine are reported over a wide range of temperature, pressure, and equivalence ratio important for enabling the validation of a chemical kinetic model for nBCH for combustion in diesel engines. The range of conditions are temperatures of 630–1420 K, pressures of 10, 30, and 50 bar, and equivalence ratios of 0.3, 0.5, 1.0, and 2.0 in ‘air’. A detailed chemical model is developed for nBCH to simulate its ignition at both low and high-temperature conditions and at relevant elevated pressures. The experimentally measured IDTs are used to improve and validate the chemical kinetic model.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

Dynamics of multilayer Rayleigh–Taylor instability at moderately high Atwood numbers

This paper investigates the multilayer Rayleigh–Taylor instability (RTI) using statistically stationary experiments conducted in a gas tunnel. Employing diagnostics such as particle image velocimetry (PIV) and planar laser induced fluorescence (PLIF), we make simultaneous velocity–density measurements to study how dynamics and mixing are linked in this variable density flow. Experiments are conducted in a newly built, blow-down three-layer gas tunnel facility. Mixing between three gas streams is studied, where the top and bottom streams are comprised of air, and the middle stream is an air–helium mixture. Shear is minimized between these streams by matching their inlet velocities. The four experimental conditions investigated here consist of two different density ratios (Atwood numbers 0.3 and 0.6), each investigated at two instability development times (or equivalently, two streamwise locations), and all experiments are with the same middle stream thickness of 3 cm. The growth of the middle layer is measured using laser-based planar Mie scattering visualization. The mixing width is found to grow linearly with time at late times. Various quantitative measures of molecular mixing indicate a very high degree of molecular mixing at late times in the multilayer RTI flow. The vertical turbulent mass flux $a_y$ is calculated. In addition to mostly negative values of $a_y$ , typical of buoyancy-dominated flows due to negative correlation between velocity and density fluctuations, positive regions are also observed in profiles of $a_y$ due to entrainment and erosion at the lower edge of the mixing region. Global energy budgets are calculated for the multilayer RTI flow at late times and it is found that the majority of potential energy released has been dissipated due to viscous effects, and a large value of mixing efficiency ( $\sim$ 60 %) is observed.

Mechanics↗
DOE OSTI2024

Controlling Product Selectivity in Photochemical CO 2 Reduction with the Redox Potential of the Photosensitizer

The ability to selectively reduce CO 2 to a particular product or mixture of products is expected to play a key role in mitigation strategies aiming to alleviate the devastating impact of this greenhouse gas in our climate and oceans. Among those, the production of liquid solar fuels from CO 2 and H 2 O will likely need cascade strategies involving multiple catalysts carrying out different functions. This will require that the catalysts doing the initial CO 2 reduction steps deliver the right product or products to downstream catalysts. CO, H 2 and formate are the most common products in CO 2 reduction by molecular catalysts. Here, in this work, we demonstrate control over the selectivity of C 1 products in photochemical CO 2 reduction with the same catalyst, simply by changing the redox potential of the photosensitizer and/or the water concentration. Turnover numbers for CO generation with one of the photosensitizers under anhydrous conditions reached 85,000, one of the largest values reported to date. A combination of experimental results and DFT calculations show that control of the selectivity is achieved, in part, due to the interplay between regimes under kinetic or thermodynamic control. These regimes are largely dictated by the proton sources and the CO 2 reduction byproducts generated.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗