Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fuels Development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
NASA NTRS2012

The Manufacture of W-UO2 Fuel Elements for NTP Using the Hot Isostatic Pressing Consolidation Process

NTP is attractive for space exploration because: (1) Higher Isp than traditional chemical rockets (2)Shorter trip times (3) Reduced propellant mass (4) Increased payload. Lack of qualified fuel material is a key risk (cost, schedule, and performance). Development of stable fuel form is a critical path, long lead activity. Goals of this project are: Mature CERMET and Graphite based fuel materials and Develop and demonstrate critical technologies and capabilities.

Broadway, Jeramie↗
NASA NTRS1993

Fuels and Combustion Technology for Advanced Aircraft Engines [Les Propergols et les Systèmes de Combustion pour les Moteurs d'Aéronefs]

The Conference Proceedings contains the 38 papers presented at the Propulsion and Energetics Panel 81st Symposium on "Fuels and Combustion Technology for Advanced Aircraft Engines" which was held from 10th-14th May 1993, in Fiuggi, Italy. The Technical Evaluation Report and the Keynote Address are included at the beginning, and discussions follow most papers. The Symposium was arranged in the following Sessions: Technology Overview Papers (2); Modelling: Pollutant Formation (4); Modelling: Combustor Design (5); High Temperature Fuels and Fuel Systems (6); Combustion Research: Performance (6); Combustion Research: Emissions (5); Fuel Atomization: Diagnostics and Modelling (5); and Combustion Research: Flowfleld and Mixing (4). The last paper is a contribution from Russia not allocated to a session. New technologies for low NOx combustors and advanced high-pressure/high temperature cycle engines result in unique problems in design and performance. There have been significant advances in modelling and diagnostics to aid the development of these technologies. The purpose of the Symposium was to bring together experts from industry, research establishments and universities to discuss fundamental and applied research in these areas as relevant to the development of advanced gas turbine engines, to exchange practical experience and to discuss the state of the art.

Fuels for aircraft↗
DOE OSTI2020

Demonstration of Integrated PostIrradiation Process Steps forMultikilogram Amounts of Low- and High-Burnup Used Nuclear Fuels

sponsored research and development (R&D) on the advanced, closed nuclear fuel cycle, including post-irradiation processing of used fuels, recovery of separated components, and preparation of recycle nuclear fuels. During the period 2007–2010, kilogram-scale demonstrations of the integrated processing steps were performed for actual light water reactor (LWR) used nuclear fuels (UNF). These integrated processing demonstrations were called “the Coupled-End-to-End” (CETE) campaigns and were associated with the Global Nuclear Energy Partnership program, which ran concurrently. The demonstrations were carried out in the shielded hot cells and associated gloveboxes located in the Irradiated Fuels Examination Laboratory (IFEL) and the Radiochemical Engineering Development Center (REDC) at the Oak Ridge National Laboratory (ORNL). Limited circulation program reports and a few technical papers were issued. The subject document provides a comprehensive summary of results, technical comparisons, and conclusions obtained from the demonstration campaigns and subsequent associated R&D.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Porosity, swelling, and composition evolution in high-burnup monolithic U-Mo fuel

The microstructural progression of very high-burnup (>8 × 10 21 fissions/cm 3 ) monolithic uranium-molybdenum (U-10wt.%Mo) was analyzed, providing crucial insights into the behavior of post-recrystallized nuclear fuel, where scant data exists. Three focused ion beam cuboids sourced from a fuel plate with varying local burnups of 8.86 × 10 21 , 9.05 × 10 21 , and 9.36 × 10 21 fissions/cm 3 were characterized. The porosity and composition of the samples were evaluated to characterize the evolution of the microstructure as a function of fission density and different locations on the fuel plate, while simultaneously isolating plate-specific parameters such as Zr diffusion barrier thickness, hot-isostatic-pressing conditions, enrichment, and reactor conditions. The porosity was segmented, and the three-dimensional distribution of the porosity was extrapolated from the two-dimensional segmentation. The composition was assessed and quantified using energy-dispersive X-ray spectroscopy areal mapping. The porosity fraction increased as a function of the burnup from 27.77±0.51, 35.12±1.54, and 37.71±0.44 % for 8.86 × 10 21 , 9.05 × 10 21 , and 9.36 × 10 21 fissions/cm 3 , respectively. When compared to literature, the porosity volume fraction plateaus at burnups greater than 6 × 10 21 fissions/cm 3 , while the pore size grows linearly as a function of fission density. The number of large pores increased in number density as a function of burnup, while the smallest pores (<0.3 µm) increased up to 9.05 × 10 21 fissions/cm 3 , followed by a decrease at 9.36 × 10 21 fissions/cm 3 . The delamination and cracking in the fuel plate propagated through an interconnected porosity sublayer identified ∼5 µm from the diffusion barrier. The local swelling of the specimens was within or near the prediction bounds of the Robinson-Williams model for local swelling. The fission products, strontium, barium, cerium, and cesium, precipitated into the pores, while neodymium accumulated adjacent to the pores. Furthermore, these findings have direct implications for the development of fuel performance codes and the accurate documentation of the microstructure evolution in high burnup U-Mo, thus enhancing the safety and efficiency of nuclear fuel usage.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

In situ self-ion (Fe + ) irradiation of ODS-FeCrAl alloy fuel cladding materials with different Cr contents: The early stages of Cr-rich α’ phase precipitation

Oxide-dispersion-strengthened FeCrAl (ODS-FeCrAl) alloys are candidate accident-tolerant fuel cladding materials for light water reactors because they demonstrate satisfactory resistance to materials degradation effects such as high-temperature oxidation, radiation-induced swelling, and creep. Their perspective deployment to market is challenged, however, by their inherent susceptibility to irradiation embrittlement caused by the precipitation of the brittle Cr-rich α’ phase at relatively low temperatures (≤475 °C). This work used in situ self-ion irradiation (150 keV Fe + ) in a transmission electron microscope to elucidate the early stages of Cr-rich α’ phase precipitation in three candidate ODS-FeCrAl alloy fuel cladding materials with different Cr contents (10, 12, and 20 wt.%) and microstructures. The early stages of the process resulting in the precipitation of the Cr-rich α’ phase in these three ODS-FeCrAl alloys under Fe + irradiation were investigated at room temperature and 300 °C up to total fluences of 1.7 × 10 15 ions·cm -2 (2 dpa) and 3.4 × 10 15 ions·cm -2 (4 dpa), using three damage dose rates (5 × 10 –5 , 3.3 × 10 –4 , and 2 × 10 –3 dpa·s -1 ). Post-irradiation examination via scanning transmission electron microscopy, energy-dispersive X-ray spectroscopy and electron energy loss spectroscopy suggested that the precipitation of the Cr-rich α’ phase might be promoted by the phase separation of the alloy matrix into Cr-rich and Fe-rich regions. Interestingly, oxygen impurities segregated preferentially in the Cr-rich regions, possibly promoting the radiation-assisted formation of the Cr-rich α’ phase. α’ phase precipitation was more pronounced at room temperature when compared to 300 °C, and it was clearly promoted by the progressive increase in the Cr content of the ODS-FeCrAl alloy.

36 MATERIALS SCIENCE↗
NASA NTRS1988

The simulation of the alternate turbopump development high pressure oxygen and fuel turbopumps for the space shuttle main engine using the Shaberth computer program

The Space Shuttle Main Engine (SSME) is basically comprised of a combustion chamber and nozzle, high and low pressure oxygen turbopumps and high and low pressure fuel turbopumps. In the current configuration, the high pressure fuel (HPTFP) and high pressure oxygen turbopumps (HPOTP) have experienced a history of ball bearing wear. The wear problem can be attributed to numerous factors including the hydrodynamic axial and radial loads caused by the flow of liquid oxygen and liquid hydrogen through the turbopump impellers and turbine. Also, friction effects between the rolling elements, races, and cage can create thermally induced bearing geometry changes. To alleviate some of the current configuration problems, an alternate turbopump development (ATD) was proposed. However, the ATD HPOTP and HPTFP are constrained to operate interchangeably with the current turbopumps, thus, the operation conditions must be similar. The ATD configuration features a major change in bearings used to support the integrated shaft, impeller, and turbine system. A single ball and single roller will replace the pump-end and turbine and duplex ball bearings. The Shaft-Bearing-Thermal (SHABERTH) computer code was used to model the ATD HPOTP and ATD HPFTP configurations. A two bearing model was used to simulate the HPOTP and HPFTP bearings and shaft geometry. From SHABERTH, a comparison of bearing reaction loads, frictional heat generation rates, and Hertz contact stresses will be attempted with analysis at the 109 percent and 65 percent power levels.

Mcdonald, Gary H.↗
DOE OSTI2020

Preliminary Study on TRISO Fuel Cross Section Generation

Cross section self-shielding methodologies for TRISO fuel were assessed to provide accurate multigroup cross sections for a high-fidelity reactor physics code so that the code is able to accurately model and simulate advanced reactors with TRISO fuel. Initially, the two existing methodologies (the SCALE method and the Sanchez-Pomraning method) were studied and implemented to MC2-3 for detailed performance tests. Additionally, a new spatial self-shielding method, named the iterative local spatial self-shielding (ILSS) method, for particulate fuels was developed based on the disadvantage factor and implemented to MC2-3 as well. The new method approximately accounts for the effect of randomly distributed particles on the particle shadowing effect using a homogenized compact region surrounding a particle of interest at the center. The self-shielded cross sections of the particle at the center are determined iteratively since the cross sections of the homogenized compact region are calculated using them. For the energy range above 100 keV where the fuel-to-moderator ratio is more important than the random distribution of particles, a single particle unit-cell model is used by preserving the average amount of moderator per fuel particle in the system. The three self-shielding methods implemented in MC2-3 were tested using numerical benchmark problems made based on fuel compact problems of a prismatic-type very high temperature reactor. Test results indicated that the ILSS method produced slightly better results than the SCALE and Sanchez-Pomraning methods, compared to the Serpent-2 Monte Carlo results obtained with 25 independent random particle configurations. The SCALE and Sanchez-Pomraning methods tend to underestimate the heterogeneity effect by 150 and 100 pcm, respectively, while the new ILSS method overestimates the heterogeneity effect by 70 pcm. In future, the new self-shielding method will be extended to perform pebble calculations and compare results with those from the SCALE and Sanchez-Pomraning methods. Furthermore, the new method will be optimized for practical applications to on-the-fly resonance treatment for lattice or whole-core calculations for advanced reactors.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1991

Rover nuclear rocket engine program: Overview of rover engine tests

The results of nuclear rocket development activities from the inception of the ROVER program in 1955 through the termination of activities on January 5, 1973 are summarized. This report discusses the nuclear reactor test configurations (non cold flow) along with the nuclear furnace demonstrated during this time frame. Included in the report are brief descriptions of the propulsion systems, test objectives, accomplishments, technical issues, and relevant test results for the various reactor tests. Additionally, this document is specifically aimed at reporting performance data and their relationship to fuel element development with little or no emphasis on other (important) items.

Finseth, J. L.↗
NASA NTRS1996

Recent Advances in High-Performance Direct Methanol Fuel Cells

Direct methanol fuel cells for portable power applications have been advanced significantly under DARPA- and ARO-sponsored programs over the last five years. A liquid-feed, direct methanol fuel cell developed under these programs, employs a proton exchange membrane as electrolyte and operates on aqueous solutions of methanol with air or oxygen as the oxidant.

fuel cells methanol methanol fuel cells DARPA ARO↗
DOE OSTI2020

ASSESSING FUEL PROPERTY EFFECTS ON CAVITATION AND EROSION PROPENSITY USING A COMPUTATIONAL FUEL SCREENING TOOL

To advance compression ignition combustion strategies, researchers have evaluated fuel property effects and their impact on achieving higher efficiencies and lower emissions levels relative to current capabilities. Within the Department of Energy's Co-Optima initiative, there has been a recent focus on understanding the influence of fuel properties on fuel injection performance. To help identify candidate fuels that can meet desired injector performance metrics, a computational fuel screening tool is under development that can link fuel properties with the tendency of a given fuel to cavitate and lead to cavitation-induced erosion. In the initial development of this tool, five liquid fuel properties were selected to represent candidate fuels, namely density, viscosity, vapor pressure, surface tension, and heat of vaporization. A design of experiments methodology was employed to generate a set of pseudo fuel cases, which can represent the main effects and interactions among the fuel properties and be related to cavitation erosion predictions. Large eddy simulations were performed using a mixture modeling approach to predict the cavitation and erosion propensity of these pseudo-fuels in terms of the mean fuel vapor mole fraction and stored impact energy from repeated cloud collapse events. The low order regression models generated from this study revealed the importance of liquid fuel density on cavitation formation, whereas liquid viscosity was found to have a strong negative correlation with erosion severity. The surrogate models were then used in the fuel screening tool to rank the cavitation and erosion tendency of four candidate single-component fuels: methyl decanoate, isooctane, ethanol and n-dodecane. While the fuel screening tool was not able to quantitatively predict the cavitation and erosion response metrics, the tool was able to accurately rank the relative cavitation and erosion propensity of the four fuels. Overall, ethanol and iso-octane were observed to produce the highest levels of cavitation and erosion, respectively.

cavitation-induced erosion↗
NASA NTRS2009

Aerojet - AJ10-137 Apollo Service Module Engine

The general configuration of the SPS engine was 20,000 pounds of thrust, with a chamber pressure of 100 psi and specific impulse (Isp) of 314.5. The very large nozzle had an area ratio of 62.5:1 (exit area to throat area). The propellants were nitrogen tetroxide (also known as N2O4 and nitrous oxide) and A-50. A-50 was a hydrazine family fuel. Aerojet developed it for the Titan Missile Program when they went with Titan II, to store it in the launch silos. They wanted the highest performance they could get. N2H4 was just pure hydrazine, which doesn't take low temperature very well. In fact, it freezes about like water. We started adding unsymmetrical-dimethylhydrazine (UDMH) to the hydrazine until such time as it would meet the environmental specifications the Air Force needed for Titan II. It turned out it s roughly a fifty-fifty mix. We still had to be careful with that fuel because the two fluids didn't mix very well chemically. We had to spray the two fluids through some special nozzles to get them to emulsify with each other into a single fluid. If we ever got it too cold or froze it, the hydrazine separated back out. Then, if we tried to run the engine, things could go boom in the night. The inlet pressure was only 165 pounds per square inch absolute (psia), but we needed at least forty psi pressure drop across the injector just to get some kind of stable flow. It was a whole new game for some of us. We didn't have much supply pressure to work with. It had the aluminum injector to keep the weight down. That was a couple feet in diameter, and we didn't have a lot of propellant to cool it. In fact, we had to use both propellants to keep the injector cool. There were twenty-two ring channels in the injector. Specification required 750 seconds duration, or fifty engine restarts during a flight. There were several first flight things we accomplished with the engine. It was the first ablative thrust chamber of any size to fly. (See Slide 6, Appendix G) There were no liners in it. It was just straight ablative material. It took us a while to figure that out. It was a throat-gimbaled engine, and it was the first engine to fly with columbium (also known as niobium, used as an alloying element in steels and superalloys) in the nozzle.

Boyce, Clay↗
DOE OSTI2021

Holistic Fuel Cell Electric Vehicle/Hydrogen Station Optimization Model (CRADA CRD-18-00745 Final Report)

The National Renewable Energy Lab (NREL), Argonne National Lab (ANL), Sandia National Lab (SNL), and Frontier Energy, Inc comprise a team that will perform a review of currently available models that can simulate both a hydrogen station and a fuel cell electric vehicle (FCEV), and whose owners are willing to make them available freely. We will then down select to a single model or model pair, secure agreements for their free use, and validate the resulting model or coupled models. For example, we may evaluate an existing 1-D hydrogen fueling model developed by Kyushu University for the Japanese New Energy and Industrial Technology Development Organization (NEDO). The validation will take place using data from various sources, potentially including the European Joint Research Center (JRC) HyTransfer project, SAE testing performed by Powertech to validate SAE J2601, and whole-station validation using the NREL’s Hydrogen Infrastructure Testing and Research Facility (HITRF). The team will make the model and all the validation data open to the public at the end of the project.

1-D hydrogen fueling model↗
NASA NTRS2015

Methodology for Producing a Uniform Distribution of UO2 in a Tungsten Matrix

Current work at NASA's Marshall Space Flight Center (MSFC) is focused on the development CERMET fuel materials for Nuclear Thermal Propulsion (NTP). The CERMETs consist of uranium dioxide (UO2) fuel particles embedded in a tungsten (W) metal matrix. Initial testing of W-UO2 samples fabricated from fine angular powders performed reasonably well, but suffered from significant fuel loss during repeated thermal cycling due to agglomeration of the UO2 (1). The blended powder mixtures resulted in a non-uniform dispersion of the UO2 particles in the tungsten matrix, which allows rapid vaporization of the interconnected UO2 from the sample edges into the bulk material. Also, the angular powders create areas of stress concentrations due to thermal expansion mismatch, which eventually cracks the tungsten matrix. Evenly coating spherical UO2 particles with chemical vapor deposited (CVD) tungsten prior to consolidation was previously demonstrated to provide improved performance. However, the CVD processing technology is expensive and not currently available. In order to reduce cost and enhance performance, a powder coating process has been developed at MSFC to produce a uniform distribution of the spherical UO2 particles in a tungsten matrix. The method involves utilization of a polyethylene binder during mixing which leads to fine tungsten powders clinging to the larger UO2 spherical particles. This process was developed using HfO2 as a surrogate for UO2. Enough powder was mixed to make 8 discs (2cm diameter x 8mm thickness) using spark plasma sintering. A uniaxial pressure of 50 MPa was used at four different temperatures (2 samples at each temperature). The first two samples were heated to 1400C and 1500C respectively for 5 minutes. Densities for these samples were less than 85% of theoretical, so the time at temperature was increased to 20 minutes for the remaining samples. The highest densities were achieved for the two samples sintered at 1700C (approx. 92% of theoretical). Scanning electron microscopy (SEM) of the mixed powders and the sintered samples along with energy dispersive x-ray analysis was obtained. The SEM of the powders clearly show the fine W powder adhered to the larger HfO2 particles and a uniform distribution of HfO2 particles in a tungsten matrix upon densification. Vicker's Microhardness testing was also performed on all samples using 0.5, 1.0 and 2.0 kg loads. Five indents were made at each load level. All indents were placed in the tungsten matrix to assist as a proxy in measuring densification. The highest hardness value was obtained for the 1700C specimens. The hardness average for these samples was 312.14 MPa. This powder processing method has been applied to W/UO2 powders with the SEM of the powders appearing similar to the W/HfO2 powder images.

Tucker, Dennis S.↗
DOE OSTI2026

Ablating Pellets for Areal Density Symmetry Control in Indirectly Driven Inertial Confinement Fusion Target Designs

Asymmetry of the compressed fusion fuel configuration, as characterized by a variation in areal density, in inertial confinement fusion (ICF) implosions is a known performance limitation. While ignition has been achieved on the National Ignition Facility (NIF), implosion symmetry was not perfect, and subsequent experiments that have extended fusion performance still struggle with symmetry control and would, in principle, perform much better if the areal density uniformity of the fuel was improved by eliminating thin regions in the DT (Deuterium-Tritium) fuel that develop by the time of peak compression. In indirect drive (IDD), altering the time-dependent laser cone fraction and cross-beam energy transfer are the usual tactics for controlling implosion asymmetry in IDD target designs, but it may be that those tools have been pushed to their limits. In this Letter, we present a new tactic for controlling the implosion using satellite ablating pellets to manipulate the time-dependent x-ray field around an ICF capsule. In theory and in simulations the action of these pellets is quite effective at reducing the swing of x-ray drive from waist hot to pole hot, thus achieving a more one-dimensional fuel configuration at peak compression. Simulations show that a factor of ∼2 in yield performance can be obtained via this technique, when applied to past record implosions on the NIF. As a result, some speculative alternate uses of the proposed target concept are also mentioned in the conclusion of this Letter.

Implosion symmetry↗
DOE OSTI2021

U-10Mo Monolithic Fuel Qualification Plan

The Material Management and Minimization (M3) Program’s primary objective within the U.S. Department of Energy/National Nuclear Security Administration is to achieve permanent threat reduction by minimizing and when possible, eliminating weapon-usable nuclear material around the world. Under M3’s Office of Conversion, the U.S. High Performance Research Reactor (USHPRR) Project, is pursuing a fuel qualification and licensing effort focused on converting high-performance research reactors in the United States from using highly enriched uranium (HEU) fuel to using low-enriched uranium (LEU) fuel. The body of this document is focused on defining the activities required for generic qualification of high density, LEU fuel that then allows reactor conversions to proceed for the four high-performance research reactors and the critical assembly that will operate using the U-10Mo monolithic fuel design (see Subsection 1.3): MITR, MURR, NBSR, ATR, and ATRC. Fuel qualification in this report means generic fuel acceptance of the U-10Mo monolithic fuel form by the NRC for use in reactor conversions in the United States, which allows the fuel to be used in subsequent reactor specific licensing requests. The U 10Mo Monolithic Fuel Research, Development, and Qualification Plan utilizes the functions and requirements of the USHPRR Project that was established in the Functions and Requirements Document (F&RD) [1] and expands on these requirements to ensure that planned tests have traceable results that will ensure the requirement has been met. The methods by which data will be collected to show that these requirements have been met are described in this document.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Multiobjective Modular Biorefinery Configuration under Uncertainty

With increasing interest in using biomass as a raw material for fuel, the development of biorefineries is an active area of research. However, increasing market competition, uncertainty, and environmental concerns are a few of the challenges that need to be addressed. In this work, mathematical optimization formulations are proposed to address these challenges simultaneously. A multiobjective deterministic optimization framework is proposed to address economic and environmental objectives. A two-stage stochastic optimization framework is proposed to account for uncertainties in material flow and product yields. To model the environmental objective, an environmental risk metric is proposed. Finally, as modularization is gaining popularity in the process industry due to its ability to save capital cost because of standardization and reduce time to market, a formulation for simultaneously achieving modular process design and biorefinery configuration is proposed. Furthermore, the results demonstrate the efficacy of the proposed approach.

09 BIOMASS FUELS↗
DOE OSTI2026

Irradiation of UC1+x kernels using the MiniFuel vehicle: Microstructure, phase analysis, and initial post-irradiation examination

Uranium carbide is a candidate fuel form for a wide range of advanced reactors, including larger Generation IV reactors as well as small modular reactors and microreactors. However, its commercial deployment timeline faces challenges via traditional qualification approaches. To address this issue, an accelerated fission rate irradiation test was performed to collect basic fuel performance data to inform fuel performance models and potential future integral tests. Hyperstoichiometric UC (UC1+x) kernels were irradiated in the High Flux Isotope Reactor using the MiniFuel irradiation vehicle. The test matrix spanned two temperature regimes (700 °C and 800 °C) and burnup levels (1.8 % FIMA and 2.8 % FIMA). Between 21 and 63 kernels were tested at each unique temperature and burnup condition. As-fabricated microstructural analysis revealed a multiphase composition with UC, UC2, UC2−y, and U-C-O bearing phases for the irradiated kernels. Following irradiation, fission gas release, swelling, and microstructures were analyzed. Measured fission gas release was below 5 % for all irradiation conditions, reaching a maximum at the highest temperature and burnup condition. A binary swelling response was observed; the lower burnup and temperature conditions resulted in negligible swelling, but the higher burnup and temperature conditions produced significant anisotropic swelling and densification in a subset of kernels. The basic microstructural exams of kernels following irradiation were not capable of showing a correlation between kernels that exhibited excessive swelling and those that did not. Characterization of a subset of samples using the Advanced Photon Source and more detailed microstructural examination of unirradiated kernels revealed that a subset of kernels contained very high UC2 phase fractions. The anomalous swelling response is hypothesized to have been driven by this chemical variation. The results of this irradiation highlight the potential of accelerated fission rate irradiation testing to explore such behaviors and inform the development of fuel specifications.

Adorno Lopes, Denise [ORNL] (ORCID:000900023705987↗
NASA NTRSDate not supplied

Modeling Validation and Its Design Relevance for NTP Fuel Elements

The development of Nuclear Thermal Propulsion engines depends heavily on modeling and simulation of a number of disciplines—neutronic / fluid / thermal / structural are only a start. Further, rockets involve extreme conditions, particularly high material temperatures in the nuclear fuel. This paper considers validation of the underling physical models and codes and how their accuracy influences several design challenges. Several issues are identified, where models, material data, could enable design solutions. In particular, thermal and CTE mismatch stresses are a concern, and stress predictions would benefit from improved mechanical property data at high temperatures. Nuclear inter-element heating causes propellant flow maldistribution and performance risks, but a simple model provides insights. High temperature chemical diffusion should be modeled to understand fuel element mass loss.

Nuclear Propulsion↗