Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FASTENING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

Design and fabrication of a large graphite-epoxy cylindrical shell

This paper describes the design and fabrication of a 10-foot diameter by 10-foot long graphite-epoxy cylinder and reports the results of developmental tests conducted with sample joints, material coupons, and stiffening ring elements. The cylindrical shell is a ring-stiffened, open corrugation design using T300/5208 graphite-epoxy tape as the basic material for the shell wall and stiffening rings. The cylinder is designed to withstand bending loads producing the relatively low maximum load intensity of 900 lb/in. The resulting shell wall weight, including stiffening rings and fasteners, is 0.37 lb/sq ft. The shell weight expected in the graphite-epoxy cylinder represents a weight savings of approximately 23 percent over that of a comparable aluminum shell. The cylinder wall was built in three flat segments which were wrapped to the cylindrical shape upon assembly. Such an approach, made possible by the flexibility of the thin corrugated wall in a radial direction, proved to be a simple one.

Johnson, R., Jr.↗

Automated space fabrication of structural elements

A description is presented of an automated space fabrication technique for basic structural elements, taking into account as representative the design loads and requirements of the solar power satellite structure. Roll forming for continuous cap and brace members is applicable for all proposed metallic materials. Spot-welding, electron beam welding, ultrasonic welding, laser welding, cold welding, and various mechanical fastening techniques are applicable for the automated fabrication process. Termination of the formed cap and brace members can be accomplished by sawing, shearing, punching, and laser cutting. The most cost effective materials were found to be the aluminum alloys. Selected for further study were AL20224T3 and AL2219-T62. In the area of fiber composites, thermoplastic matrix materials with graphite fibers were selected for future studies.

Engler, E. E.↗

Extra-strong "floating nut"

Increased bearing area withstands much higher torque than previous designs. Floating nut makes it possible to fasten parts on heavy-duty equipment, such as tractors and cranes, even though they can be reached for tightening from one side only.

Charles, J. F.↗

Flight service evaluation of Kevlar-49 epoxy composite panels in wide-bodied commercial transport aircraft

Kevlar-49 fairing panels, installed as flight service components on three L-1011s, were inspected after five years' service. There are six Kevlar-49 panels on each aircraft: a left-hand and right-hand set of a wing-body sandwich fairing; a solid laminate under-wing fillet panel; and a 150 C (300 F) service aft engine fairing. The fairings have accumulated a total of 40,534 hours, with one ship set having 16,091 hours service as of Feb. 11, 1979. The Kevlar-49 components were found to be performing satisfactorily in service with no major problems, or any condition requiring corrective action. The only defects noted were minor impact damage, and a minor degree of fastener hole fraying and elongation. These are for the most part comparable to damage noted on fiberglass fairings.

Stone, R. H.↗

Test evaluation of space station ECLSS maintenance concepts

The Space Station Prototype (SSP) Environmental Control and Life Support System (ECLSS) hardware was designed and built to be maintainable by the flight crew. To achieve this goal, subsystems were designed for ease of component removal and installation, which included accessibility to component fasteners and connectors, adequate tool clearance, minimum fluid loss during changeout, positive capture of loose parts during changeout, replacement by one crewman, and protection of adjacent parts during maintenance. During testing of this hardware, many day-to-day problems arose which allowed the evaluation of the maintenance concepts under actual maintenance conditions. This paper briefly discusses the maintenance objectives of the hardware design. Specific maintenance designs and their test evaluations are discussed. A removable cartridge valve concept for liquid line components and threaded mechanical fittings and V-band couplings for gaseous line components are critiqued. Other maintenance devices are also evaluated.

Reysa, R. P.↗

Magnetic shielding in a low temperature torsion pendulum experiment

A new type of ether drift experiment searches for anomalous torques on a permanent magnet. A torsion pendulum is used at liquid helium temperature, so that superconducting cylinders can be used to shield magnetic fields. Lead shields attenuate the earth's field, while Nb-Sn shields fastened to the pendulum contain the fields of the magnet. The paper describes the technique by which the earth's field can be reduced below 0.0001 G while simultaneously the moment of the magnet can be reduced by a factor 7 x 10 to the 4th.

Phillips, P. R.↗

Bayonet plug with ramp-activated lock

Matched pair of washers with broad surface ramps is locking mechanism in bayonet plug. It can be used where threaded springs and fasteners are impractical because of extreme temperatures or other environmental incompatibility. Matched pair of ramped washers is placed on plug and bayonet inserted. Inner slot of one washer matches contour of plug; this washer is stationary. Inner slot of second washer is circular. When second washer is rotated, washers push against bayonet plug, locking it in place. Retaining wire secures plug.

Wood, K. E.↗

Interchangeable spring modules for inertia measurements

Operation of inertia balance is simplified by packaging set of balance springs in interchangeable modules. They are held in place in balance pedestal by just two fasteners, making removal and replacement fast and simple. With them, balance can be readied in less than 15 minutes, in contrast to more than 2 hours by previous method.

Mcnamara, J. W.↗

Torque-wrench extension

Torque-wrench extension makes it easy to install and remove fasteners that are beyond reach of typical wrenches or are located in narrow spaces that prevent full travel of wrench handle. At same time, tool reads applied torque accurately. Wrench drive system, for torques up to 125 inch-pounds, uses 2 standard drive-socket extensions in aluminum frame. Extensions are connected to bevel gear that turns another bevel gear. Gears produce 1:1 turn ratio through 90 degree translation of axis of rotation. Output bevel has short extension that is used to attach 1/4-inch drive socket.

Peterson, D. H.↗

Soft container for explosive nuts

Flexible fabric fits over variety of assembly shapes to contain debris produced by detonations or safety tests. Bag material is woven multifilament polyamide or aramid. Belt loops hold bag to clamp. Ring supports explosive nut structure and detonator wires, and after nut is mounted, bag and clamp are slipped over ring and fastened.

Glenn, D. C.↗

Eliminating gaps in split rings

Simple installation method allows thinner, lighter tether rings than conventional procedures, saving expensive materials. Installer inverts ring with pliers before it is slid over cable, then returns it to its original position after installation. Ring is in correct orientation, and coils are tightly compressed for high reliability fastening.

Gould, R. W.↗

Selected topics from the structural acoustics program for the B-1 aircraft

The major elements of the structural acoustics program for the B-1 aircraft are considered. Acoustic pressures measured at 280 sites on the surface of the vehicle were used to develop pressure models for a resizing of airframe components for aircraft No. 4 (A/C4). Acoustical fatigue design data for two dynamically complex structural configurations were acquired in laboratory programs, the conceptions for and executions of which detailed significant departures from the conventional. Design requirements for mechanical fasteners for configurations other than these two made use of analytical extensions of regrettably limited available information.

Belcher, P. M.↗

A device for determining the intensity of partial sweating

An invention which can measure partial perspiration is disclosed. The partial perspiration is measured with a specially shaped device tightly fastened to the body but not touching the skin area being studied. A special grid is used to keep the moisture-absorbing agent from touching the skin.

Rayskiy, V. A.↗

Flight service evaluation of Kevlar-49 epoxy composite panels in wide-bodied commercial transport aircraft

Kevlar-49 fairing panels, installed as flight service components on three L-1011s, were inspected after 6 years' service. The Kevlar-49 components were found to be performing satisfactorily in service with no major problems, or any condition requiring corrective action. The only defects noted were minor impact damage, and a minor degree of fastener hole fraying and elongation. These are for the most part comparable to damage noted on fiberglass fairings.

Stone, R. H.↗

Automated beam builder

Requirements for the space fabrication of large space structures are considered with emphasis on the design, development, manufacture, and testing of a machine which automatically produces a basic building block aluminum beam. Particular problems discussed include those associated with beam cap forming; brace storage, dispensing, and transporting; beam component fastening; and beam cut-off. Various critical process tests conducted to develop technology for a machine to produce composite beams are also discussed.

Muench, W. K.↗

Thermal performance of a mechanically attached ablator tile for on-orbit repair of shuttle TPS

The reusable surface insulation (RSI) material used in the shuttle thermal protection system is susceptible to damage. If any RSI tiles are damaged or lost during ascent, they must be repaired or replaced prior to entry. One approach to replacing a damaged or missing RSI tile consists of mechanically attaching a tile of ablation material in the place of the RSI tile. The thermal performance of this type of repair tile was evaluated in a simulated entry heating environment. The test specimen consisted of the ablator repair tile mechanically fastened to the strain isolation pad and surrounded by RSI tiles. The evaluation of the thermal performance was based on temperature response, surface integrity, and predicted flight performance. When the ablator tile protruded 1/8 inch above the surrounding RSI tiles, the forward facing steps caused significant inflow of hot gas down the ablator RSI joints and this inflow caused greatly increased back surface temperatures.

Thompkins, S. S.↗

Notch sensitivity of space shuttle tile materials

Tests were conducted at room temperature to determine the notch sensitivity of the thermal protection tile for the space shuttle. Two types of RSI tile were studied: LI-900 and LI-2200. Three point bend specimens were cut from discarded tiles in the in-plane (ip) and through-the-thickness (ttt) directions. They were tested with or without a sharp notch. The LI-900 (ip and ttt) specimens were not very notch sensitive, but the LI-2200 (ip and ttt) specimens were. The LI-2200 material showed about a 35 percent reduction in strength due to the presence of the notch. This reduction in strength should be considered in the design of mechanically fastened tile concepts.

Newman, J. C., Jr.↗

Small Transport Aircraft Technology

The article surveys the results of the NASA-instituted Small Transport Aircraft Technology (STAT) research effort aimed at generating advanced technologies for application to new small, short haul transports having significantly better performance, efficiency, and environmental compatibility. Discussion covers fuselage designs and bonded aluminum-honeycomb wing construction which reduces the number of parts and fasteners, and gives a smoother outer contour. Topics discussed include: advanced aluminum alloys, composite primary structures, propellers, engine components, icing protection, avionics, flight controls, aerodynamics, and gust load alleviation.

Galloway, T. L.↗