Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Encapsulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

Photovoltaic-Panel Laminator

Two-piece unit heats and presses protective layers to form laminate. Rubber diaphragm between upper and lower vacuum chambers alternates between neutral position and one that presses against solar-cell array, supplying distributed force necessary to press layers of laminate together. Encapsulation helps to protect cells from environment and to ensure long panel life while allowing efficient generation of electricity from Sunlight.

Keenan, R.↗

Bonding Solar-Cell Modules

Status of research program on chemical bonding for solar-cell arrays subject of 57-page report. Program aimed at identifying, developing, and validating weather-stable chemical bonding promoters. Materials key to ensuring long life in encapsulated photovoltaic modules for electric-power generation. To be cost-effective, modules must hold together for at least 20 years, reliably resisting delamination and separation of component materials

Coulter, D. R.↗

Removing Heat From Toroidal Inductors

Bracket for mounting toroidal inductors adapted for removing heat and providing support. Copper windings wound around bracket instead of directly on core. Heat-dissipating mounting bracket encircles hollow cylindrical magnetic core. Core wrapped with toroidal winding and encapsulated in usual way. Bracket provides direct path for heat to leave both core and windings.

Mclyman, C. W. T.↗

Laser Photoacoustic Technique Detects Photo-Oxidation

Laser photoacoustic instrument detects small amounts of oxidation in polymers. Instrument used to evaluate resistance to oxidation in Sunlight of polymer encapsulants for solar-cell arrays. With instrument, researchers monitor samples for early stages of photooxidation and study primary mechanisms of oxidation and degradation. Effects of these mechanisms masked during later stages.

Liange, R. H.↗

More Secure Fastening for Tracked-Vehicle Pads

Method of fastening road pads on tracked vehicles ensures retaining tabs properly installed and less likely to fail from shock or pad squirming when tracked vehicle turns. No risk squirming of pad might overcome retaining force of rubber encapsulation or teeth of split-collet fastener shred soft-iron projections on pad shell, causing inadvertent release of pad. Rod extending through track shells and tabs on pad shells includes grooved cams to secure pads.

Collins, Earl R., Jr.↗

Accelerating Corrosion in Solar-Cell Tests

In simple electrochemical cell, two silicon solar cells serve as anode and cathode, respectively. Electrolytic medium and voltage between them accelerate corrosion and migration interactions between cell metal contacts and plastic encapsulant. Degradation of metal contacts becomes evident in few hours. Although developed specifically for cells with Ti/Pd/Ag contacts, technique readily adapted to other metal combinations.

Shalaby, H. M.↗

Flat-plate module efficiency versus cost tradeoffs

The Five Year Research Plan energy cost methodology and in depth analyses based on the extensive data that are relevant to PV systems are used to facilitate the accomplishment of the $0.15/kWh energy cost goal. An equation is given for the five year energy cost methodology. The allocation guidelines are designed to be consistent with flat solar array (FSA) milestones for module cost, module efficiency, and the programmatic goal for energy cost. They are research targets that appear to be achievable, given prior accomplishments and planned activities in the areas of low cost silicon purification, low cost sheet material, high efficiency cell processing, low cost, long life encapsulants, and automated fabrication method. Extensive sensitivity analysis work has been performed that shows that these guidelines represent an efficient way to meet the intent of the DOE program.

Aster, R. W.↗

Reliability physics

Speakers whose topics relate to the reliability physics of solar arrays are listed and their topics briefly reviewed. Nine reports are reviewed ranging in subjects from studies of photothermal degradation in encapsulants and polymerizable ultraviolet stabilizers to interface bonding stability to electrochemical degradation of photovoltaic modules.

Cuddihy, E. F.↗

Photovoltaic module spread-of-flame testing

Photovoltaic modules used in solar energy conversion are tested for flammability. Class B burning brand tests were conducted with the following results: module glass shattered and hydrocarbon encapsulants ignited. Penetration of back surface material was the prime cause of failure. Materials with greater flame and heat resistance are under consideration to increase back surface integrity up to Class A burning brand standard. The most promising is stainless steel foil.

Sugimura, R. S.↗

Chemical feasibility of lithium as a matrix for structural composites

The chemical compatibility of lithium with tows of carbon and aramid fibers and silicon carbide and boron monofilaments was investigated by encapsulating the fibers in liquid lithium and also by sintering. The lithium did not readily wet the various fibers. In particular, very little lithium infiltration into the carbon and aramid tows was achieved and the strength of the tows was seriously degraded. The strength of the boron and silicon carbide monofilaments, however, was not affected by the liquid lithium. Therefore lithium is not feasible as a matrix for carbon and aramid fibers, but a composite containing boron or silicon carbide fibers in a lithium matrix may be feasible for specialized applications.

Swann, R. T.↗

Assessing photovoltaic module degradation and lifetime from long term environmental tests

The photovoltaic module failure mechanisms related to temperature, humidity, and electrical bias are analyzed using the data collected over a period of 20 years from various sites in the U.S. The approach is based on measuring the rate dependence of the mechanisms on site stress levels, and then using the rate data to analytically estimate the field life by means of computer models of the site environment. A correlation is established between the accelerated constant-stress testing and the time-varying field exposures. Test results are presented for two failure mechanisms for a module design featuring polyvinyl butyral encapsulant for the temperature range of 85 to 100 C and 85-percent relative humidity.

Otth, D. H.↗

The integration of bypass diodes with terrestrial photovoltaic modules and arrays

Bypass diodes are often required to limit the potential for reverse voltage 'hot-spot' heating in high voltage arrays or in arrays that undergo periodic operation near the short-circuit point. In addition, when properly applied, bypass diodes can minimize the effect of shadowing and various internal module failures on the array energy output. This paper discusses the mechanical and electrical integration of bypass diodes beginning with the array-level considerations which influence the selection of an implementation approach. Concepts for the mounting of these diodes, both internally within the module encapsulant and externally to the exposed rear surface of the module, are described. Factors affecting the reliability of bypass diodes, including the control of junction temperature through adequate heat sinking and the derating of reverse voltage, are discussed.

Shepard, N. F., Jr.↗

Status of high efficiency module design and fabrication

The status of an ongoing DOE program to develop an AM1 photoelectric module with 15 percent conversion efficiency at normal heating temperatures, is reviewed. Emphasis is given to the efforts of a private company to develop a high efficiency module which also has high durability in normal operating conditions. The main design options considered are: high efficiency modules; large area modules; and optimized module fabrication techniques. The design of an automatic system for encapsulating module stacks is described.

Nowlan, M. J.↗

Diffusion in Immiscible Melts

The objective of this program is to measure the diffusion coefficients for molten Pb in Zn in the immiscible liquid-phase region. Diffusion couples of pure Pb and Zn were prepared using a shear cell. These have been placed in graphite crucibles and encapsulated in stainless steel cartridges and are awaiting the next Materials Experiment Assembly (MEA) flight opportunity. In flight, one couple will be soaked for 40 minutes at 440 deg C (just above the monotectic temperature) and the second couple will be soaked for 40 minutes 820 deg C (just above the consolute temperature). After the soak both samples will be rapidly quenched by flowing He to minimize redistribution of the immiscible phases. Post flight compositional analysis will be accomplished using X-ray fluorescence in the scanning electron microscopy.

Pond, R. B.↗

Advances in Joining Techniques Used in Development of SPF/DB Titanium Sandwich Reinforced with Metal Matrices

Three and four-sheet expanded titanium sandwich sheets have been developed at Douglas Aircraft Company, a division of McDonnell Douglas Corporation, under contract to NASA Langley Research Center. In these contracts, spot welding and roll seam welding are used to join the core sheets. These core sheets are expanded to the face sheets and diffusion bonded to form various type cells. The advantages of various cell shapes and the design parameters for optimizing the wing and fuselage concepts are discussed versus the complexity of the spot weld pattern. In addition, metal matrix composites of fibers in an aluminum matrix encapsulated in a titanium sheath are aluminum brazed successfully to the titanium sandwich face sheets. The strength and crack growth rate of the superplastic-formed/diffusion bonded (SPF/DB) titanium sandwich with and without the metal matrix composites are described.

Fischler, J. E.↗

Glass breaking strength: The role of surface flaws and treatments

Although the intrinsic strength of silicon dioxide glass is of the order of 10 to the 6th power lb/sq in, the practical strength is roughly two orders of magnitude below this theoretical limit, and depends almost entirely on the surface condition of the glass, that is, the number and size of flaws and the residual surface compression (temper) in the glass. Glass parts always fail in tension when these flaws grow under sustained loading to some critical size. Research associated with glass encapsulated crystalline-Si photovoltaic (PV) modules has greatly expanded our knowledge of glass breaking strength and developed sizeable data base for commercially available glass types. A detailed design algorithm is developed for thickness sizing of rectangular glass plates subject to pressure loads. Additional studies examine the strength of glass under impact loading conditions such as that caused by hail. Although the fundamentals of glass breakage are directly applicable to thin film modules, the fracture strength of typical numerical glass must be replaced with data that reflect the high temperature tin oxide processing, laser scribing, and edge processing peculiar to thin film modules. The fundamentals of glass breakage applicable to thin film modules and preliminary fracture strength data for a variety of 1 ft square glass specimens representing preprocessed and post processed sheets from current amorphous-Si module manufacturers are presented.

Moore, D.↗

High gradient directional solidification furnace

A high gradient directional solidification furnace is disclosed which includes eight thermal zones throughout the length of the furnace. In the hot end of the furnace, furnace elements provide desired temperatures. These elements include Nichrome wire received in a grooved tube which is encapsulated y an outer alumina core. A booster heater is provided in the hot end of the furnace which includes toroidal tungsten/rhenium wire which has a capacity to put heat quickly into the furnace. An adiabatic zone is provided by an insulation barrier to separate the hot end of the furnace from the cold end. The old end of the furnace is defined by additional heating elements. A heat transfer plate provides a means by which heat may be extracted from the furnace and conducted away through liquid cooled jackets. By varying the input of heat via the booster heater and output of heat via the heat transfer plate, a desired thermal gradient profile may be provided.

Aldrich, B. R.↗