Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ENCAPSULATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
DOE OSTI2017

Building America Case Study: Heat Pump Water Heater Ducting Strategies with Encapsulated Attics in Climate Zones 2 and 4, LaFayette, Georgia (CZ4), and Savannah, Georgia (CZ2)

The focus of this study is on the performance of HPWHs with several different duct configurations and their effects on whole building heating, cooling, and moisture loads. A.O. Smith 60 gallon Voltex (PHPT-60) heat pump water heaters (HPWHs) were included at two project sites and ducted to or located within spray foamed encapsulated attics. The effect of ducting a HPWH's air stream does not diminish its efficiency if the ducting does not reduce intake air temperature, which expands HPWH application to confined areas. Exhaust ducts should be insulated to avoid condensation on the exterior, however this imposes a risk of condensation occurring in the duct's interior near the HPWH due to large variation of temperatures between the compressor and the duct and the presence of bulk moisture around the condenser. The HPWH's air conditioning impact on HVAC equipment loads is minimal when the intake and exhaust air streams are connected to a sealed attic and not the living space. A HPWH is not suitable as a replacement dehumidifier in sealed attics as peak moisture loads were observed to only be reduced if the heat pump operated during the morning. It appears that the intake air temperature and humidity was the most dominant variable affecting HPWH performance. Different ducting strategies such as exhaust duct only, intake duct only, and exhaust and intake ducting did not have any effect on HPWH performance.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2017

Cementing a wellbore using cementing material encapsulated in a shell

A system for cementing a wellbore penetrating an earth formation into which a pipe extends. A cement material is positioned in the space between the wellbore and the pipe by circulated capsules containing the cement material through the pipe into the space between the wellbore and the pipe. The capsules contain the cementing material encapsulated in a shell. The capsules are added to a fluid and the fluid with capsules is circulated through the pipe into the space between the wellbore and the pipe. The shell is breached once the capsules contain the cementing material are in position in the space between the wellbore and the pipe.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Encapsulation of high temperature molten salts

The present disclosure relates to a method of encapsulating microcapsules containing relatively high temperature phase change materials and the microcapsules so produced. The microcapsules are coated with an inorganic binder, film former and an inorganic filler. The microcapsules may include a sacrificial layer that is disposed between the particle and the coating. The microcapsules may also include an inner coating layer, sacrificial layer and outer coating layer. The microcapsules are particularly useful for thermal energy storage in connection with, e.g., heat collected from concentrating solar collectors.

25 ENERGY STORAGE↗
DOE OSTI2017

Building America Case Study: Heat Pump Water Heater Ducting Strategies with Encapsulated Attics in Climate Zones 2 and 4, LaFayette, Georgia (CZ4), and Savannah, Georgia (CZ2)

The focus of this study is on the performance of HPWHs with several different duct configurations and their effects on whole building heating, cooling, and moisture loads. A.O. Smith 60 gallon Voltex (PHPT-60) heat pump water heaters (HPWHs) were included at two project sites and ducted to or located within spray foamed encapsulated attics. The effect of ducting a HPWH's air stream does not diminish its efficiency if the ducting does not reduce intake air temperature, which expands HPWH application to confined areas. Exhaust ducts should be insulated to avoid condensation on the exterior, however this imposes a risk of condensation occurring in the duct's interior near the HPWH due to large variation of temperatures between the compressor and the duct and the presence of bulk moisture around the condenser. The HPWH's air conditioning impact on HVAC equipment loads is minimal when the intake and exhaust air streams are connected to a sealed attic and not the living space. A HPWH is not suitable as a replacement dehumidifier in sealed attics as peak moisture loads were observed to only be reduced if the heat pump operated during the morning. It appears that the intake air temperature and humidity was the most dominant variable affecting HPWH performance. Different ducting strategies such as exhaust duct only, intake duct only, and exhaust and intake ducting did not have any effect on HPWH performance.

Building America↗
DOE OSTI2017

Encapsulation of thermal energy storage media

In one embodiment, a phase change material is encapsulated by forming a phase change material pellet, coating the pellet with flexible material, heating the coated pellet to melt the phase change material, wherein the phase change materials expands and air within the pellet diffuses out through the flexible material, and cooling the coated pellet to solidify the phase change material.

25 ENERGY STORAGE↗
DOE OSTI2018

Encapsulated sulfur cathodes for rechargeable lithium batteries

A method of forming a sulfur-based cathode material includes: 1) providing a sulfur-based nanostructure; 2) coating the nanostructure with an encapsulating material to form a shell surrounding the nanostructure; and 3) removing a portion of the nanostructure through the shell to form a void within the shell, with a remaining portion of the nanostructure disposed within the shell.

25 ENERGY STORAGE↗
DOE OSTI2018

Finite Element Simulation of Mixed-Mode PV Encapsulant Delamination Based on Cohesive Zone Model: Preprint

A finite element model (FEM) was developed to simulate the mixed-mode delamination failure at the encapsulant interface within PV modules under mixed-mode loading condi- tions. Parameters to characterize the bilinear traction-separation constitutive behavior of cohesive elements were determined by testing the pure mode I critical fracture energy of the photovotaic(PV) cell interface using the width-tapered beam and fitting the simulated load-displacement curve with the tested curve. This developed FEM can be used to predict the critical temperature changes, at which delamination would initiate, of PV modules with different sizes and provide guidance for the design of PV module with better reliability.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2020

Encapsulated sulfur cathodes for rechargeable lithium batteries

A method of forming a sulfur-based cathode material includes: 1) providing a sulfur-based nanostructure; 2) coating the nanostructure with an encapsulating material to form a shell surrounding the nanostructure; and 3) removing a portion of the nanostructure through the shell to form a void within the shell, with a remaining portion of the nanostructure disposed within the shell.

25 ENERGY STORAGE↗
DOE OSTI2020

Systems and methods for additive manufacturing to encapsulate transformative colloidal suspensions

The present disclosure relates to a method of forming an energy absorbing three dimensional (3D) structure. The method involves forming an outer shell for the 3D structure from a shell material, the outer shell having a void forming a core volume. The method also involves filling the core volume with a transformative liquid. When the 3D structure is fully formed, the transformative liquid is encapsulated within the outer shell and provides enhanced energy absorbing properties to the 3D structure.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Photovoltaic devices with encapsulating barrier film

Encapsulated device including a photovoltaic cell and a composite film overlaying at least a portion of the photovoltaic cell, the composite film further including a substrate, a base (co)polymer layer on a major surface of the substrate, an oxide layer on the base (co)polymer layer, and a protective (co)polymer layer derived from a silane precursor compound on the oxide layer.

14 SOLAR ENERGY↗
DOE OSTI2021

Encapsulated sulfur cathodes for rechargeable lithium batteries

A method of forming a sulfur-based cathode material includes: 1) providing a sulfur-based nanostructure; 2) coating the nanostructure with an encapsulating material to form a shell surrounding the nanostructure; and 3) removing a portion of the nanostructure through the shell to form a void within the shell, with a remaining portion of the nanostructure disposed within the shell.

Li, Weiyang↗
DOE OSTI2022

Systems and methods for additive manufacturing to encapsulate transformative colloidal suspensions

The present disclosure relates to an energy absorbing three dimensional (3D) structure. The structure may have an outer shell formed from a shell material. The outer shell may have a void forming a core volume. A transformative feedstock is contained in the void. The transformative feedstock is encapsulated within the outer shell, within the void, and provides enhanced energy absorbing properties to the 3D structure.

Mancini, Julie A.↗
DOE OSTI2013

Recovery of uranium from phosphoric acid medium by polymeric composite beads encapsulating organophosphorus extractants

The present study deals with the preparation and evaluation of the poly-ethersulfone (PES) based composite beads encapsulating synergistic mixture of D2EHPA and Cyanex 923 (at 4:1 mole ratio) for the separation of uranium from phosphoric acid medium. SEM was used for the characterization of the composite materials. Addition of 1% PVA (polyvinyl alcohol) improved the internal morphology and porosity of the beads. Additionally, microscopic examination of the composite bead confirmed central coconut type cavity surrounded by porous polymer layer of the beads through which exchange of metal ions take place. Effect of various experimental variables including aqueous acidity, metal ion concentration in aqueous feed, concentration of organic extractant inside the beads, extractant to polymer ratio, liquid to solid (L/S) ratio and temperature on the extraction of uranium was studied. Increase in acidity (1-6 M), L/S ratio (1- 10), metal ion concentration (0.2-3 g/L U{sub 3}O{sub 8}) and polymer to extractant ratio (1:4 -1:10) led to decrease in extraction of uranium. At 5.5 M (comparable to wet process phosphoric acid concentration) the extraction of uranium was about 85% at L/S ratio 5. Increase in extractant concentration inside the bead resulted in enhanced extraction of metal ion. Increase in temperature in the range of 30 to 50 Celsius degrees increased the extraction, whereas further increase to 70 C degrees led to the decrease in extraction of uranium. Amongst various reagents tested, stripping of uranium was quantitative by 12% Na{sub 2}CO{sub 3} solution. Polymeric beads were found to be stable and reusable up-to 10 cycles of extraction/stripping. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2016

Cementitious Grouts for ILW Encapsulation - Hydration and Continuity of Supply within the UK - 16184

In the UK the preferred route to disposal for the majority of intermediate level nuclear waste (ILW) streams is encapsulation within a cementitious matrix, accounting for 83% of waste conditioned to date (NDA, 2013). The method is well-defined and produces a waste package that is both chemically and physically stable, providing a multi-layered barrier to the release of the waste species contained within. Due to the process of treatment, facilitated via remote operation, it is necessary for the grouting matrices to meet strict performance limits in terms of their flow, setting time and avoidance of the formation of bleed water or segregation. To this end, the limits on composition of the anhydrous materials (a mixture of ordinary Portland cement [OPC] and blast furnace slag [BFS]) are tight to ensure conformity. Whilst these limits on composition are well understood, their impact upon grout hydration, and hence performance, is poorly defined. This study investigates the effects of modifying the physical and chemical composition of both the OPC and the BFS components of the matrix in order to identify the sensitivity or otherwise of the system to ensure that a continuity of supply is maintained. A number of techniques, scanning electron microscopy - image analysis (SEM-IA), chemical shrinkage (measured via dilatometry), isothermal conduction calorimetry (ICC), thermogravimetric analysis (TGA) and X-ray diffraction (XRD), have been applied to assess the rate and degree of hydration (DoH) of a range of grouts prepared with OPC and BFS with a range of chemical and physical compositions. This has been coupled with subsequent engineering performance testing, with additional analysis to understand the impact of a fire scenario within a storage or disposal facility, to provide an indication towards the resilience of the waste packages to a potential catastrophic event. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

An Experimental Feasibility Study on Applying Neutron Tomography to Encapsulated Spent Nuclear Fuel - 20050

Visual inspection makes easier to ensure the integrity and safety of spent nuclear fuel (SNF) than any classical techniques. Various classical techniques have been applied but there are no reliable methods to qualitatively and quantitatively verify spent fuel in dry storage. Thus, the present authors have developed the prototype safeguards apparatus for dry storage employing the array of He-4 gas scintillation detectors (S670E, Arktis Radiation Detectors Ltd., Switzerland), newly designed to simultaneously measure thermal and fast neutrons without any moderators. The S670E detector has a cylindrical shape with a diameter of 52 mm and active length of 600 mm (total length: 875 mm). The detector is filled by He-4 gas with an approximate pressure of 180 bar for fast neutron detection, and its inner wall is coated by Li-6 for thermal neutron detection. The scintillation lights generated via Li-6 nuclear reaction and elastic scattering are collected by 24 SiPMs linearly paired at the center of the detector. The detector delivers a TTL (Transistor-Transistor Logic) output for pulse readout and UART (Universal Asynchronous Receiver Transmitter) for device control. In order to assess feasibility of the apparatus, an experimental system has been designed, built, and optimized via computational studies. Cf-252 neutron sources and linearly arrayed detectors, working as a single detector, were occupied for this study due to the difficulties in working with SNF. The laboratory scale cask (diameter: 0.67 m, height: 1.5 m), minimized by a factor of 10 compared to the actual thickness of a commercial TN-32 cask, was also manufactured. The detector array was designed to rotate the lab-scale cask and obtain 36 image profiles at every 10 degrees. All profiles were aligned in single frame image called a sinogram, and the cross-sectional image was then fabricated by the inverse radon transform algorithm. These experiments have been repeated with different configurations and numbers of sources. Some gamma-ray sources were also measured with neutron sources in order to distinguish between neutron and gamma-ray pulses. Basically, a He-4 detector is designed to run on Linux OS so it is difficult to directly apply to Windows-based equipment widely used in S. Korea. Therefore, a new data acquisition board working on Windows OS was designed and built. The board mainly consists of FPGA (Field Programmable Gate Array) and SoC (System on Chip) for TTL pulse readout, sorting measured data, and transferring data to a user interface. In conclusion, the tomographic system at lab-scale has shown considerable potential to detect a partial or gross defect of encapsulated assemblies in dry storage. Next steps of this study will be to 1) repeatedly carry out experiments to demonstrate scientific reliability and validity, and 2) numerically integrate signals with weight factors to enhance the image quality since the suggested system based on passive interrogation method requires longer measurement time. Finally, the system will apply to a commercial dry storage phased out soon in S. Korea. (authors)

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2023

Techno-economic and environmental life cycle assessment of next-generation fiber-encapsulated nanoscale hybrid materials for direct air carbon capture

A techno-economic and environmental life cycle assessment was conducted for manufacturing two novel types of solid sorbents used for direct air CO 2 capture (DAC). One type of solid sorbent comprised Polyacrylonitrile (PAN)/Organopolysilizane (OPSZ)/nanoscale organic hybrid materials (NOHM)(, and the other comprised polymers of intrinsic microporosity (PIM)/NOHM. These solid sorbents were assumed to be manufactured via an unconventional route: electrospinning as fibers. Economic analyses revealed that manufacturing costs for a 0.73 MT/year capacity plant was $\$$831 and $\$$1398/kg of electrospun fiber in the case ofPAN/OPSZ/NOHM and PIM/NOHM, respectively. The costs were higher for PIM/NOHM owing to high raw material prices (Spirobisindane and tetrafluoroterephthalonitrile), that are used only in manufacturing PIM. Scaling up the plant capacity from 0.73 to 30 MT/year plant decreased the manufacturing cost by nearly half from $\$$831 to $\$$379 in the case of PAN/OPSZ/NOHM, depicting the economies of scale of effect. An LCA of both types of solid sorbent was performed using OpenLCA software, the Ecoinvent v 3.5 database, and the TRACI LCI assessment method. The Global Warming Potential (GWP) ofPAN/OPSZ/NOHM and PIM/NOHM was observed to be 151 × 10 -3 and 166 × 10 -3 kg CO 2 per kg CO 2 captured in the DAC plant, respectively. In conclusion, these GWP values were nearly five times as high as those observed for other solid sorbents existing in the literature such as PEI on silica gel, carbonate on silica, and carbonate on activated carbon owing to large amounts of electricity used in electrospinning unit operation.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Quantitative Encapsulation and Homogeneity Assessment of Sol–Gel Based Nuclear Explosive Debris Simulants

Nuclear explosive debris simulants are an important material in training and validating aspects of post-detonation nuclear forensic processes. Realistic simulants should replicate several aspects of nuclear explosive debris such as the size, shape, color, density, and chemical and radiological properties. Silica particles produced via sol-gel synthesis have recently been found to successfully reproduce many of these parameters including the controllable incorporation of radionuclide content. However, to be useful as a benchmarking material for validation and verification of laboratory methodologies, radionuclide content from batch-to-batch must be reproducible. Here, in this work, we explore the variance in radionuclide distribution incorporated into sol-gel benchmarking materials with respect to sample subdivision. Results will help inform the sample sizes required to minimize variance between samples.

36 - MATERIALS SCIENCE↗