Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ELASTIC PROPERTY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

Material Failure Model and Properties for Puncture Simulations

Sharp tools in a production environment can puncture fragile components. This project analyzes a slender probe as it penetrates a ductile material. Finite element models of probe penetration problems need material models that are accurate through the full range of strain. Elastic properties are frequently derived and are available for most metals with a strong statistical basis. Stress-strain curves including the plastic range are limited and usually stop at the ultimate strength, where void nucleation occurs. Criteria for damage accumulation and rupture are difficult to obtain for many materials. Tests have been performed on coupons of 7075-T651 plate with three probes. The geometry of the coupon and probes are provided, as well as appropriate initial and boundary conditions. The mean energy required for each of the probes to penetrate the coupon is also provided. The objective of this project is to demonstrate three advanced material models for 7075-T651 plate with failure criteria and derive the requisite parameters for each model.

36 MATERIALS SCIENCE↗

A microstructure-guided constitutive modeling approach for random heterogeneous materials: Application to structural binders

This paper presents a microstructure-guided modeling approach to predict the effective elastic response of heterogeneous materials, and demonstrates its application toward two highly heterogeneous, uncon- ventional structural binders, i.e., iron carbonate and fly ash geopolymer. Microstructural information from synchrotron X-ray tomography (XRT) and intrinsic elastic properties of component solid phases from statistical nanoindentation are used as the primary inputs. The virtual periodic 3D microstructure reconstructed using XRT, along with periodic boundary conditions is used as a basis for strain- controlled numerical simulation scheme in the linear elastic range to predict the elastic modulus as well as the stresses in the microstructural phases. The elastic modulus of the composite material predicted from the microstructure-based constitutive modeling approach correlates very well with experimental measurements for both the materials considered. This technique efficiently links the microstructure to mechanical properties of interest and helps develop material design guidelines for novel heterogeneous composites

36 MATERIALS SCIENCE↗

Hexagonal boron nitride nanomechanical resonators with spatially visualized motion

Atomic layers of hexagonal boron nitride (h-BN) crystal are excellent candidates for structural materials as enabling ultrathin, two-dimensional (2D) nanoelectromechanical systems (NEMS) due to the outstanding mechanical properties and very wide bandgap (5.9 eV) of h-BN. In this work, we report the experimental demonstration of h-BN 2D nanomechanical resonators vibrating at high and very high frequencies (from ~ 5 to ~ 70 MHz), and investigations of the elastic properties of h-BN by measuring the multimode resonant behavior of these devices. First, we demonstrate a dry-transferred doubly clamped h-BN membrane with ~ 6.7 nm thickness, the thinnest h-BN resonator known to date. In addition, we fabricate circular drumhead h-BN resonators with thicknesses ranging from ~ 9 to 292 nm, from which we measure up to eight resonance modes in the range of ~ 18 to 35 MHz. Combining measurements and modeling of the rich multimode resonances, we resolve h-BN’s elastic behavior, including the transition from membrane to disk regime, with built-in tension ranging from 0.02 to 2 N m -1 . The Young’s modulus of h-BN is determined to be EY≈392 GPa from the measured resonances. The ultrasensitive measurements further reveal subtle structural characteristics and mechanical properties of the suspended h-BN diaphragms, including anisotropic built-in tension and bulging, thus suggesting guidelines on how these effects can be exploited for engineering multimode resonant functions in 2D NEMS transducers.

36 MATERIALS SCIENCE↗

Out-Life Characteristics of IM7/977-3 Composites

The capability to manufacture large structures leads to weight savings and reduced risk relative to joining smaller components. However, manufacture of increasingly large composite components is pushing the out-time limits of epoxy/ carbon fiber prepreg. IM7/977-3 is an autoclave processable prepreg material, commonly used in aerospace structures. The out-time limit is reported as 30 days by the manufacturer. The purpose of this work was to evaluate the material processability and composite properties of 977-3 resin and IM7/977-3 prepreg that had been aged at room temperature for up to 60 days. The effects of room temperature aging on the thermal and visco-elastic properties of the materials were investigated. Neat resin was evaluated by differential scanning calorimetry to characterize thermal properties and change in activation energy of cure. Neat resin was also evaluated by rheometry to characterize its processability in composite fabrication. IM7/977-3 prepreg was evaluated by dynamic mechanical analysis to characterize the curing behavior. Prepreg tack was also evaluated over 60 days. The overall test results suggested that IM7/977-3 was a robust material that offered quality laminates throughout this aging process when processed by autoclave.

Miller, Sandi G.↗

Effect of Rotor Blade Elasticity on UAM Quadrotor Acoustics

The 6-passenger quadrotor concept vehicle designed under the NASA Revolutionary Vertical Lift Technology (RVLT) Project is considered for acoustic analysis. The tip speed is 550 ft/sec, with three blades per rotor (550/3). Originally, the blades were rigid, uniform spanwise, and with flap and pitch degrees of freedom. The blade model has since been updated: a lag hinge was added, and nonuniformities and elastic properties were introduced. Four blade models are considered: 1) original model, rigid uniform flap-pitch; 2) rigid uniform flap-lag-pitch; 3) rigid nonuniform flap-lag-pitch; and 4) elastic nonuniform flap-lag-torsion. Predictions are made for three flight conditions (approach, flyover, and takeoff) using the four blade models. The RVLT Toolchain is exercised using CAMRAD II and pyaaron/AARON/ANOPP2. Quadrotor trim and performance, 0.75R vertical blade loading for all four rotors, and noise sources are analyzed. Also, the contributions of the front and rear rotor pairs to noise are studied. In approach and flyover, a 2 dBA loading noise difference (delta) is predicted between blade models 1 and 4 (delta for takeoff is smaller, 1 dBA). Most of this noise delta is due to the lag hinge and nonuniformities, which is consistent with the results of a 2022 study that had considered only the approach condition; the current results extend this conclusion to flyover and takeoff also. The insensitivity of quadrotor noise to blade elasticity is currently attributed to the high blade torsional stiffness (frequency 6.41 per rev) and the small blade radius (9 ft) of the 550/3 design. Suggestions for potential follow-on work are given.

Rotor Blade↗

Modelling and simulations of the chemo-mechanical behaviour of leached cement-based materials: Interactions between damage and leaching

The assessment of the durability of cement-based materials, which could be employed in underground structures for nuclear waste disposal, requires accounting for deterioration factors, such as chemical attacks and damage, and for the interactions between these phenomena. The objective of the present paper consists in investigating the long-term behaviour of cementitious materials by simulating their response to chemical and mechanical solicitations. In a companion paper (Stora et al., submitted to Cem. Concr. Res. 2008), the implementation of a multi-scale homogenization model into an integration platform has allowed for evaluating the evolution of the mineral composition, diffusive and elastic properties inside a concrete material subjected to leaching. To complete this previous work, an orthotropic micromechanical damage model is presently developed and incorporated in this numerical platform to estimate the mechanical and diffusive properties of damaged cement-based materials. Simulations of the chemo-mechanical behaviour of leached cementitious materials are performed with the tool thus obtained and compared with available experiments. The numerical results are insightful about the interactions between damage and chemical deteriorations.

36 MATERIALS SCIENCE↗

Shape-Preserved Transformation of Biological Cells into Synthetic Hydrogel Microparticles

The synthesis of materials that can mimic the mechanical, and ultimately functional, properties of biological cells can broadly impact the development of biomimetic materials, as well as engineered tissues and therapeutics. Yet, it is challenging to synthesize, for example, microparticles that share both the anisotropic shapes and the elastic properties of living cells. Here in paper, a cell-directed route to replicate cellular structures into synthetic hydrogels such as polyethylene glycol (PEG) is described. First, the internal and external surfaces of chemically fixed cells are replicated in a conformal layer of silica using a sol–gel process. The template is subsequently removed to render shape-preserved, mesoporous silica replicas. Infiltration and cross-linking of PEG precursors and dissolution of the silica result in a soft hydrogel replica of the cellular template as demonstrated using erythrocytes, HeLa, and neuronal cultured cells. The elastic modulus can be tuned over an order of magnitude (≈10–100 kPa) though with a high degree of variability. Furthermore, synthesis without removing the biotemplate results in stimuli-responsive particles that swell/deswell in response to environmental cues. Overall, this work provides a foundation to develop soft particles with nearly limitless architectural complexity derived from dynamic biological templates.

59 BASIC BIOLOGICAL SCIENCES↗

Simultaneous structure and elastic wave velocity measurement of SiO[subscript 2] glass at high pressures and high temperatures in a Paris-Edinburgh cell

An integration of multi-angle energy-dispersive x-ray diffraction and ultrasonic elastic wave velocity measurements in a Paris-Edinburgh cell enabled us to simultaneously investigate the structures and elastic wave velocities of amorphous materials at high pressure and high temperature conditions. We report the first simultaneous structure and elastic wave velocity measurement for SiO{sub 2} glass at pressures up to 6.8 GPa at around 500 C. The first sharp diffraction peak (FSDP) in the structure factor S(Q) evidently shifted to higher Q with increasing pressure, reflecting the shrinking of intermediate-range order, while the Si-O bond distance was almost unchanged up to 6.8 GPa. In correlation with the shift of FSDP position, compressional wave velocity (Vp) and Poisson's ratio increased markedly with increasing pressure. In contrast, shear wave velocity (Vs) changed only at pressures below 4 GPa, and then remained unchanged at {approx}4.0-6.8 GPa. These observations indicate a strong correlation between the intermediate range order variations and Vp or Poisson's ratio, but a complicated behavior for Vs. The result demonstrates a new capability of simultaneous measurement of structures and elastic wave velocities at high pressure and high temperature conditions to provide direct link between microscopic structure and macroscopic elastic properties of amorphous materials.

47 OTHER INSTRUMENTATION↗

Improved bounds on elastic and transport properties of fiber-reinforced composites - Effect of polydispersivity in fiber radius

Improved rigorous bounds were computed on the effective elastic and transport properties (including the effective axial shear modulus, effective transverse bulk modulus, and effective transverse shear modulus) of a transversely isotropic fiber-reinforced material composed of infinitely-long oriented multisized impenetrable circular cylinders distributed throughout a matrix. Results were used to study the effect of fiber-radius polydispersivity on the elastic and transport properties of such unidirectional composites. It was found that increasing the degree of polydispersivity increases the effective transverse conductivity (or axial shear modulus) and the effective transverse bulk modulus, and slightly decreases the effective transverse shear modulus for cases in which the fibers are more conducting or stiffer than the matrix.

Miller, C. A.↗

An Elastic Analysis of a Plated Bone to Determine Fracture Gap Motion

An elastic analysis to determine fracture gap motions occurring in the osteotomized and plated canine femur was performed using the finite element program NASTRAN. The femur was idealized as a hollow right cylinder, and transverse anisotropy was assumed for the elastic properties of the bone. A 3-D 360 degree model consisting of 224 isoparametric quadrilateral hexahedral and 11 beam elements was created. A range of plate stiffnesses was tested by varying the modulus of elasticity of the plate from 207 GPa to 1 GPA. Moments were applied in the plane of the plate, about the axis of the plate, and in the plane of the screws. Results showed that, for plates of typical geometry and elastic modulus under 10 GPa, the contribution to fracture gap motion occurring due to deformation in the bone was negligible compared to that contribution from deformation in the plate.

Cooke, F. W.↗

Ab initio studies of structural, electronic, optical, elastic and thermal properties of CuGaTe{sub 2}

We have performed ab initio calculations for the structural, electronic, optical, elastic and thermal properties of CuGaTe{sub 2}. In this study, we used an accurate full potential linearized augmented plane wave (FP-LAPW) method to find the equilibrium structural parameters and to compute the full elastic tensors. We report electronic and optical properties with the recently developed density functional of Tran and Blaha. Furthermore, optical features such as dielectric functions, refractive indices, extinction coefficient, optical reflectivity, absorption coefficients, optical conductivities, were calculated for photon energies up to 30 eV. The thermodynamical properties such as Debye temperature, entropy and Gruneisen parameter, bulk modulus and hardness were calculated employing the quasi-harmonic Debye model at different temperatures (0–1000 K) and pressures (0–8 GPa) and the silent results were interpreted. Most of the investigated parameters are reported for the first time.

36 MATERIALS SCIENCE↗

Resonant ultrasound spectroscopy probe for in-situ neutron scattering measurements

Resonant ultrasound spectroscopy (RUS) is an efficient, nondestructive technique to study the elastic properties of solids. A low-temperature (2-300 K) probe has been assembled and tested at the NOMAD beamline at the Spallation Neutron Source at Oak Ridge National Laboratory to assess the probe's neutronic properties, data acquisition system, and compatibility with existing sample environment. A case study on a bulk metallic glass, La 65 Cu 20 Al 10 Co 5, served to benchmark both hardware and software developments. The elastic constants of the metallic glass were determined as a function of temperature between 4 and 300 K and were used to guide neutron diffraction measurements at NOMAD. Tracking of a specific RUS peak center frequency and width enabled live monitoring of the sample temperature evolution that lagged thermometry by upwards of 40 K near room temperature. Assembly of a high-temperature (300-875 K) probe is underway and both probes are scheduled to be available to users by late-2021. Our aim is to provide users with live monitoring of an intrinsic variable at the neutron scattering beamlines, in addition to existing controls, to monitor the state of their samples and its elastic moduli and make informed decisions in real time.

Torres, James↗

Nondestructive Measurement of the Evolution of Layer-Specific Mechanical Properties in Sub-10 nm Bilayer Films

We use short wavelength extreme ultraviolet light to independently measure the mechanical properties of disparate layers within a bilayer film for the first time, with singlemonolayer sensitivity. We show that in Ni/Ta nanostructured systems, while their density ratio is not meaningfully changed from that expected in bulk, their elastic properties are significantly modified, where nickel softens while tantalum stiffens, relative to their bulk counterparts. In particular, the presence or absence of the Ta capping layer influences the mechanical properties of the Ni film. This non-destructive nano-mechanical measurement technique represents the first approach to date able to distinguish the properties of composite materials well below 100 nm in thickness. As a result, this capability is critical for understanding and optimizing the strength, flexibility and reliability of materials in a host of nanostructured electronic, photovoltaic and thermoelectric devices.

36 MATERIALS SCIENCE↗

Elastic and thermodynamic properties of cerium-doped yttrium aluminum garnets

Cerium-doped yttrium aluminum garnets (Y 3-x Ce x Al 5 O 12 , Ce:YAGs) are promising yellow light-emitting components of solid-state white light-emitting diodes. Although there have been numerous studies examining the effects of Ce concentrations on the luminescent properties of Y 3-x Ce x Al 5 O 12 , the impacts of Ce dopant on the elastic and thermodynamic properties are not well understood. In this work, we used resonant ultrasound spectroscopy (RUS) to determine the effects of Ce doping (0.025, 0.1, 1 at. %) on the elastic and thermodynamic properties of Y 3-x Ce x Al 5 O 12 . The elastic moduli calculated via the Voigt–Reuss–Hill (VRH) method demonstrated that low Ce dopant concentrations (≤0.1 at. %) induced negligible effects on the elasticity of the YAG host matrix, while a high Ce concentration (1 at. %) yielded significant softening. RUS spectral analysis and SEM images suggested that the elastic softening originated from microstructural differences induced at higher Ce dopant concentrations. Additionally, we demonstrated an increase in elastic anisotropy at higher Ce concentrations, which further elucidated the correlations between structure and elasticity of Y 3-x Ce x Al 5 O 12 . Debye temperatures ($θ_D$), heat capacities ($C_p$), and thermal conductivities ($\mathit{κ}$) were calculated for Ce:YAGs through the relations of RUS-derived parameters (sound velocities, elastic moduli) and previously determined thermal expansion coefficients. Ce:YAG was found to have a significant reduction in $θ_D$, Cp, and $\mathit{κ}$ at Ce concentrations ≥1 at. %. Lastly, extrapolation of $C_p$ and $\mathit{κ}$ to higher temperatures allowed the modeling of thermal stress experienced by Y 3-x Ce x Al 5 O 12 disks up to 1073.15 K.

36 MATERIALS SCIENCE↗

Laminate behavior for SiC fiber-reinforced reaction-bonded silicon nitride matrix composites

The room temperature mechanical properties of SiC fiber reinforced reaction-bonded silicon nitride matrix composite laminates (SiC/RBSN) have been measured. The laminates contained approx 30 volume fraction of aligned 142-micron diameter SiC fiber in a porous RBSN matrix. Three types of laminate studied were unidirectional: (1) (0) sub 8, (2) (10) sub 8, and (3) (45) sub 8, and (90) sub 8; cross plied laminates (0 sub 2/90 sub 2); and angle plied laminates: (+45 sub 2/-45 sub 2). Each laminate contained eight fiber plies. Results of the unidirectionally reinforced composites tested at various angles to the reinforcement direction indicate large anisotropy in in-plane properties. In addition, strength properties of these composites along the fiber direction were independent of specimen gage length and were unaffected by notches normal to the fiber direction. Splitting parallel to the fiber at the notch tip appears to be the dominant crack blunting mechanism responsible for notch insensitive behavior of these composites. In-plane properties of the composites can be improved by 2-D laminate construction. Mechanical property results for (0 sub 2/90 sub 2)sub s and (+45/-45 sub 2) sub s laminates showed that their matrix failure strains were similar to that for (0) sub 8 laminates, but their primary elastic moduli, matrix cracking strengths, and ultimate composite strengths were lower. The elastic properties of unidirectional, cross-ply, and angle-ply composites can be predicted from modified constitutive equations and laminate theory. Further improvements in laminate properties may be achieved by reducing the matrix porosity and by optimizing the bond strength between the SiC fiber and RBSN matrix.

Rhatt, R. T.↗

Laminate behavior for SiC fiber-reinforced reaction-bonded silicon nitride matrix composites

The room temperature mechanical properties of SiC fiber reinforced reaction-bonded silicon nitride matrix composite laminates (SiC/RBSN) have been measured. The laminates contained approx 30 volume fraction of aligned 142-micron diameter SiC fiber in a porous RBSN matrix. Three types of laminate studied were unidirectional: (1) (0) sub 8, (2) (10) sub 8, and (3) (45) sub 8, and (90) sub 8; cross plied laminates (0 sub 2/90 sub 2); and angle plied laminates: (+45 sub 2/-45 sub 2). Each laminate contained eight fiber plies. Results of the unidirectionally reinforced composites tested at various angles to the reinforcement direction indicate large anisotropy in in-plane properties. In addition, strength properties of these composites along the fiber direction were independent of specimen gage length and were unaffected by notches normal to the fiber direction. Splitting parallel to the fiber at the notch tip appears to be the dominant crack blunting mechanism responsible for notch insensitive behavior of these composites. In-plane properties of the composites can be improved by 2-D laminate construction. Mechanical property results for (0 sub 2/90 sub 2) sub s and (+45/-45 sub 2) sub s laminates showed that their matrix failure strains were similar to that for (0) sub 8 laminates, but their primary elastic moduli, matrix cracking strengths, and ultimate composite strengths were lower. The elastic properties of unidirectional, cross-ply, and angle-ply composites can be predicted from modified constitutive equations and laminate theory. Further improvements in laminate properties may be achieved by reducing the matrix porosity and by optimizing the bond strength between the SiC fiber and RBSN matrix.

Bhatt, Ramakrishna T.↗

Compressibility and hardness of Co-based bulk metallic glass: A combined experimental and density functional theory study

An incompressible Co{sub 54}Ta{sub 11}B{sub 35} bulk metallic glass (BMG) was investigated using in situ high-pressure synchrotron diffraction and nanoindendation. The elastic constants were deduced from the experiments based on the isotropic model. The Vickers hardness was measured to be 17.1 GPa. The elastic moduli and hardness are the highest values known in BMGs. The theoretically calculated elastic properties by density-functional study were well consistent with experimental measurements. The analysis of charge density and bonding character indicates the covalent character of Co-B and B-B bonds, underlying the unusually high elastic modulus and hardness in this material.

36 MATERIALS SCIENCE↗

Mechanical Response of Thermoelectric Materials

A sufficient mechanical response of thermoelectric materials (TEMats) to structural loadings is a prerequisite to the exploitation of any candidate TEMat's thermoelectric efficiency. If a TEMat is mechanically damaged or cracks from service-induced stresses, then its thermal and electrical functions can be compromised or even cease. Semiconductor TEMats tend to be quite brittle and have a high coefficient of thermal expansion; therefore, they can be quite susceptible to mechanical failure when subjected to operational thermal gradients. Because of this, sufficient mechanical response (vis-a-vis, mechanical properties) of any candidate TEMat must be achieved and sustained in the context of the service-induced stress state to which it is subjected. This report provides an overview of the mechanical responses of state-of-the-art TEMats; discusses the relevant properties that are associated with those responses and their measurement; and describes important, nonequilibrium phenomena that further complicate their use in thermoelectric devices. For reference purposes, the report also includes several appendixes that list published data on elastic properties and strengths of a variety of TEMats.

36 MATERIALS SCIENCE↗