Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Ductility”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Engineering Multi-scale B2 Precipitation in a Heterogeneous FCC Based Microstructure to Enhance the Mechanical Properties of a Al0.5Co1.5CrFeNi1.5 High Entropy Alloy

While ordered L12 or gamma prime precipitates in face centered cubic (FCC) based microstructures have been extensively used for strengthening Nickel or Cobalt base superalloys, and more recently in high entropy alloys (HEAs) or complex concentrated alloys (CCAs), the possibility of exploiting ordered B2 precipitates in FCC-based systems has been relatively less investigated. The present study shows the propensity of developing a heterogeneous microstructure, consisting of two different distributions of FCC grain sizes, and two different size scales of B2 precipitates, within an FCC-based Al0.5Co1.5CrFeNi1.5 HEA/CCA. This alloy composition has been designed using solution thermodynamics-based modeling such that it has a high phase fraction and solvus temperature of the B2 phase. The resulting heterogenous microstructure exhibited an approximately 400% increase in yield strength with respect to the single-phase FCC solid solution condition of the same alloy while maintaining very good tensile ductility ~20 %.

Dasari, Sriswaroop↗
DOE OSTI2020

Dislocation cross-slip in precipitation hardened Mg–Nd alloys

An integrated experimental characterization and molecular dynamics (MD) simulation approach was used to explore the dislocation-precipitate interactions in a dilute Magnesium–Neodymium (Mg–Nd) precipitation hardened alloy. In situ indentation in a transmission electron microscope (TEM) and postmortem TEM characterization of deformed samples and MD simulations revealed that basal < a > type dislocations interacted differently with β 1 (Mg 3 Nd) and β"(Mg 3-7 Nd) precipitates. For β" precipitates, the basal dislocations directly shear the precipitates. For β 1 precipitates, such shearing becomes much more difficult because it requires the creation of antiphase boundaries in the ordered lattice of β 1 precipitates. Screw dislocations were observed to cross-slip from basal to the prismatic plane, which could be parallel to the broad facet of β 1 precipitates. It is postulated that double cross-slip (basal to prismatic to basal) via the Hirsch mechanism may enable screw dislocations to overcome the β 1 precipitates. MD simulations also revealed that an edge dislocation is unable to bypass the precipitate via the generation of screw dislocation segments plus the double cross-slip mechanism. The edge dislocation can bow around the precipitate, and the segment that adopts a screw character can cross-slip to the prismatic plane but with increasing applied stress, cross-slips back to the original basal plane to continue glide via precipitate shearing. Finally, the implication of glide dislocation - β 1 -precipitate interaction mechanisms on the strength and ductility of β 1 precipitate dominant microstructures is discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Unraveling peculiar magnetism and band topology in Mn 3 Sb

Magnetic, pseudogap, topological, magnetostructural, and elastic behaviors of Mn 3 Sb have been unraveled. The ferrimagnetism (FIM) is described by localized and delocalized electron magnetism resulting in different magnetic moments on Mn atoms, confirming the neutron diffraction data. The identified magnetostructural properties are due to the non-equivalent Mn atoms in its lowest symmetry structure. The electronic structure is also unique due to variable valance states of Mn atoms. The magnetic moment (4.10 μB) of non-equivalent Mn1 atom is antiparallely aligned with the magnetic moments (2.34 μB) of Mn 2 and Mn 3 atoms. The estimated Curie temperature, TC, is higher than the room temperature, which may have above the room temperature applications in spintronic devices. The band structure and density of states (DOS) show the characteristics of band topology (opening of a gap in Dirac-like band features) and pseudo-gap, respectively, around the Fermi level. While expanding the unit cell, the tetragonal FIM ground state transforms to the cubic primitive FIM phase, however, the contraction transforms it to the L1 2 ferromagnetic (FM) phase. The estimated elastic constants, bulk to shear modulus ratio, and elastic anisotropy factor indicate that Mn3Sb exhibits mechanically stable, ductile, and anisotropic behaviors, respectively.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Investigating the failure behavior of cast Al-11Ce-0.4Mg alloys using in-situ scanning electron microscopy tensile testing

Within the last decade, research on Al-Ce-Mg alloys has reported promising results for use in cast part applications. In this paper, the failure behavior of cast Al-11Ce-0.4Mg (wt%) was investigated experimentally with focus on the effect the matrix and intermetallic phases have on the fracture propagation behavior at failure. For the first time, in-situ SEM tensile testing was used to study the failure behavior of cast Al-Ce alloys, reporting results for uniaxial, DIC, and single edge notch tensile tests. The results of the in-situ SEM tensile testing were compared with the materials characterization experiments, which included serial sectioning, EBSD, EDS, and fractography. Analysis of EBSD and EDS mapping of cast Al-11Ce-0.4Mg showed that the cast microstructure was a hypereutectic two phase Al-Ce alloy with grains encompassing large complex colonies of laminar eutectic Al 11 Ce 3 intermetallic. The uniaxial tensile results reported the effect casting defects have on the strength and ductility of the alloy, and DIC in-situ testing showed that the eutectic colonies plastically deform less than the matrix phase. In-situ SEM single edge notch tensile testing displayed how the strength of an individual phase affected the crack propagation direction in the alloy. The results of both the materials characterization and in-situ tensile testing experiments on the failure of this alloy revealed further directions for future alloy development that can improve both the strength and fracture toughness of Al-Ce-Mg alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Directed energy deposition of radially functionally graded nickel based superalloys IN625 and IN738: Microstructure and mechanical properties

This study investigates the microstructure and mechanical properties of radially functionally graded (RFG) materials fabricated from nickel-based superalloys IN625 and IN738 using directed energy deposition (DED). RFG cylindrical deposits with radial gradients of IN625-IN738 and IN738-IN625 were successfully fabricated and confirmed to be crack-free through tailored composition grading, scan strategy and process parameters that minimized thermal gradients and solidification velocities. Microstructural analysis revealed distinct variations across the gradient, characterized by differences in dendrite arm spacing, microsegregation, and the formation of distinct γ' precipitates and carbide/boride phases (MC, M 6 C, M 2 C, and MB 2 ) in as-deposited (AD) conditions, which evolved into M 23 C 6 and M 2 B upon subsequent heat treatment (HT). EBSD showed predominant columnar grains with a [100] texture, while microhardness profiles demonstrated consistent variation across the gradients. Mechanical testing highlighted the synergy of the graded structure, combining IN738's strength with IN625's ductility, resulting in enhanced properties such as a yield strength of 1131 MPa, ultimate tensile strength of 1382 MPa, and elongation of 12 % for HT IN625-IN738 grading. Numerical simulations employing CALPHAD thermodynamic calculations and finite element thermal modeling are used to establish phase evolution and microstructural feature correlation with thermal profiles, aiding in the optimization of process-structure-property relationship.

Additive manufacturing↗
DOE OSTI2025

Microstructural features underpinning the mechanical behavior of powder metallurgy Cr-based alloys

Refractory materials such as Cr-based alloys offer the potential of enhanced elevated temperature performance but have been limited by their poor formability. However, powder metallurgy has been shown to be a viable pathway to fabricate these alloys. Nanophase separation sintering (NPSS) in particular has been used in the literature to accelerate the densification of powder metallurgy Cr- and W-based alloys. Here, we explore microstructure evolution during NPSS in a binary Cr 85 Ni 15 alloy consolidated via (i) cold pressing & pressureless sintering and (ii) hot isostatic pressing followed by hot extrusion & hot upsetting, and the role of these different processing routes on resulting material properties. The alloy lacked room temperature tensile ductility regardless of consolidation process, with multi-length scale characterization, including scanning electron microscopy, transmission electron microscopy, atom probe tomography, X-ray diffraction, and uniaxial tensile testing, revealing that brittleness was due to intrinsically poor Cr grain boundary cohesion. Tensile testing conducted at 760 °C showed marked strength reduction for the extruded & upset (94 %) condition compared to the pressed & sintered (18 %). The formation of orthorhombic CrNi 2 intermetallics functioned as precipitate strengtheners and prevented elevated temperature softening in the pressed and sintered condition. The findings offer foundational insights into aiding the future development of Cr-based alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2025

High-pressure high-temperature melting and recrystallization of nanolamellar high-entropy alloys

Additively manufactured (AM) High Entropy Alloys (HEAs) are notable for their exceptional high-yield strength and large tensile ductility. The nanolamellar Eutectic HEA (EHEA) AlCoCrFeNi 2.1 was fabricated by laser powder bed fusion (L-PBF) in the as-printed form (EHEA1) and subsequently annealed at 1000oC (EHEA2) and 600oC (EHEA3) to achieve a broad range of mechanical properties. EHEA2 and EHEA3 samples were studied using Scanning transmission electron microscopy (STEM), energy dispersive X-ray diffraction (EDXRD) at high-pressures and high temperatures, nanoindentation hardness and modulus measurements. According to EDXRD EHEA2 and EHEA3 are composed of B2 and L1 2 phases. High-pressure high-temperature EDXRD studies show melting for EHEA2 at 1698 ± 25 K at a pressure of 6.5 GPa and melting for EHEA3 at 1598 ± 25 K at a pressure of 5.8 GPa. Post-melt and recrystallized samples were recovered at ambient conditions, and XRD analysis showed retention of B2 and L1 2 phases, although a new σ phase appeared for both EHEA2 and EHEA3 samples due to high-pressure and high-temperature melting and recrystallization experiment. SEM analysis also demonstrated the preservation of the nanolamellar morphology. Nanoindentation studies revealed that recrystallized EHEAs retain their original mechanical property hierarchy, with EHEA3 being 47% harder than EHEA2, largely related to higher content of B2-phase and retention of nanolamellar morphology. We also present Pressure-Volume-Temperature (P-V-T) data for 3-D printed and annealed eutectic high entropy alloys and extract mechanical and thermal properties data.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effects of processing temperature, pressure, and fiber volume fraction on mechanical and morphological behaviors of fully-recyclable uni-directional thermoplastic polymer-fiber-reinforced polymers

This work explores a type of composite called thermoplastic polymer-fiber-reinforced polymers (PFRPs), often referred to as self-reinforced composites (SRCs). A representative PFRP was exemplified using unidirectional (UD) ultra-high-molecular-weight polyethylene (UHMWPE) fibers embedded in a high-density polyethylene (HDPE) matrix. The effects of compression molding temperature and pressure on the mechanical and morphological behaviors of the filament-wound PFRPs with various fiber volume fractions (V f ) were experimentally investigated. The results elucidate the evolution of morphologies and tensile properties of the PFRPs due to thermal melting, fiber misalignment from pressure, and (V f )-induced structural variance, which has not been comprehensively reported yet. The highest specific tensile strength and modulus of the PFRP laminae reach 600 MPa/(g/cm 3 ) and 31 GPa/(g/cm 3 ), respectively. These properties are comparable to glass-/aramid-fiber-reinforced polymers (GFRPs, GFRTPs, AFRPs, and AFRTPs), with PFRPs exhibiting better ductility (specific strain at peak load ≈ 4%/(g/cm 3 )) than other common polymer composites. The motivation for this work was the high recyclability of PFRPs, which can be recycled by melting both the fibers and the matrix, and then reshaped them for re-manufacturing composites to maximize the efficiency in material reuse. This process simplifies the implementation of closed-loop recycling, re-manufacturing, and reuse to support sustainability in composites. This work aims to contribute to advancing thermoplastic PFRPs for their potential applications in various industries.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Activation of dislocations in Mg with solute Y

Mg-Y cast alloy shows excellent ductility (elongation to failure > 15%) compared with pure Mg and commercial Mg cast alloys. By monitoring the microstructure evolution during an in situ tensile test of a Mg-2.5 wt%Y alloy, we identify the activation of prismatic slip, which is rare in Mg. Synchrotron X-ray micro-beam Laue diffraction (μ-Laue) and transmission electron microscopy revealed the morphology of prismatic slip bands and individual dislocations. Density functional theory and molecular dynamics calculations indicate that solute Y can significantly reduce the stacking fault energy (SFE) along direction on prismatic plane in Mg lattice and thus facilitate the nucleation of dislocations during deformation. The presence of free dislocations in the Mg lattice can also lead to nucleation of {10–12} twins even under unfavorable geometric conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Formation of I 1 stacking fault by deformation defect evolution from grain boundaries in Mg

I 1 stacking faults (SFs) in Mg alloys are regarded as the nucleation sites of $\langle \text{c+a} \rangle$ dislocations that are critical for these alloys to achieve high ductility. Previously it was proposed that the formation of I 1 SFs requires the accumulations of a large number of vacancies, which are difficult to achieve at low temperatures. In this study, molecular dynamics (MD) and molecular statics (MS) simulations based on empirical interatomic potentials were applied to investigate the deformation defect evolutions from the symmetric tilt grain boundaries (GBs) in Mg and Mg-Y alloys under external loading along $\langle c \rangle$-axis. The results show the planar faults (PFs) on Pyramidal I planes first appear due to the nucleation and glide of $\langle {\frac {1}{2}}c + p\rangle$ partial dislocations from GBs, where $\langle p\rangle$ = ${\frac {1}{3}} \langle10\bar{1}0\rangle$. These partial dislocations with pyramidal PFs interact with other defects, including pyramidal PFs themselves, GBs, and $\langle p\rangle$ partial dislocations, generating a large amount of I 1 SFs. Detailed analyses show the nucleation and growth of I 1 SFs are achieved by atomic shuffle events and deformation defect reactions without the requirements of vacancy diffusion. Our simulations also suggest the Y clusters at GBs can reduce the critical stress for the formation of pyramidal PFs and I 1 SFs, which provide a possible reason for the experimental observations that Y promotes the $\langle{\text{c+a}}\rangle$ dislocation activities.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Experimental characterization and atomistic simulation of grain boundary segregation in Mg-Y alloys

As a rare earth solute element in Mg alloys, Y has the beneficial effects of increasing both the strength and the ductility as well as weakening the crystallographic texture. To achieve a more fundamental understanding on how Y addition affects the microstructural evolution and mechanical properties, the Y segregation behavior at grain boundaries was investigated in Mg-1wt.%Y and Mg-7wt.%Y alloys at different conditions. The segregation intensity and its dependence on the grain boundary misorientation angle were experimentally characterized and computationally predicted. Strong segregation at grain boundaries was observed in both low and high Y-containing alloys. Y segregation was found to remain in alloy Mg-7Y after high-temperature annealing heat treatment at 540 °C. No direct correlation between the Y segregation intensity and the grain boundary misorientation angle could be established based on either the experimental characterization or the atomistic simulation with a spectral model. We thus conclude that grain boundary segregation of Y is independent of grain boundary misorientation angle.

Grain boundary↗
DOE OSTI2022

Microstructure-refinement–driven enhanced tensile properties of high-pressure die-cast A380 alloy through friction stir processing

This work employs friction stir processing (FSP), a well-known severe plastic deformation technique, to selectively modify the microstructure of thin-walled, high-pressure die-cast (HPDC) aluminum alloy A380, a major HPDC alloy fabricated in the die casting sector. FSP effectively breaks down Al dendrites and acicular Si particles, creating a homogenized distribution of equiaxed Si particles in the aluminum matrix. After FSP, the refined Si particles (~1.5 µm) are smaller than the eutectic Si particles (3–8 µm) in HPDC condition. In addition, interparticle distance has decreased almost 50% compared to dendritic arm spacing, and FSP has reduced the aspect ratio of Si particles to ~2. Furthermore, FSP eliminates porosity, and breaks down needle-like second-phase Fe-Mn and Cu-rich particles, yielding a refined, homogeneous distribution. The FSP-induced microstructural refinement and porosity reduction improve bulk yield strength and ductility by 23% and 66%. Tensile properties are enhanced beyond those of the die skin of the HPDC plate, and the alloy possesses lower defect density and a highly refined microstructure. This study establishes the viability of FSP as a tool for microstructure modification and mechanical property improvement for HPDC Al alloys for the light-weighting goal of the automotive industries.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Friction extrusion of ODS copper rod made from powder

Meters-long oxide dispersion strengthened copper rods were manufactured directly from powder by a single-step process, called friction extrusion. The average grain size was 880 nm, which was refined 40 times from powder precursor due to extensive shear deformation. Meanwhile, the average size of alumina particles was 60 nm which retains a decent oxide dispersion strengthening. Here, mechanical properties, including hardness, tensile strength, and ductility, were tested and found to have better or similar values than conventional sintered-then-extruded oxide dispersion strengthened copper materials. The presented technique promises a convenient avenue for the fabrication of oxide dispersion strengthened copper from powder.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Additive manufacturing of AISI M2 tool steel by binder jetting (BJ): Investigation of microstructural and mechanical properties

The presented research demonstrates for the first time the successful processing of AISI M2 tool steel by binder jetting, a promising additive manufacturing technique capable of producing complex shapes with minimal residual stresses and isotropic properties. The optimal printing parameters were explored by varying processing parameters such as the binder saturation (45 %–105 %), binder set time (0 to 10 s), targeted bed temperature (50–60 °C), oscillator (2600–2750 rpm), recoater (20–28 mm/s), and roller speeds (200–300 rpm). Microstructural characterization and evaluation of mechanical properties of binder jetted parts were performed using x-ray diffraction (XRD), scanning electron microscopy (SEM), and energy dispersive spectroscopy (EDS) to study their chemical composition, powder morphology, microstructure, carbide morphologies, relative density, hardness, compressive strength, and ductility. Two powder sizes (5 and 10 μm) were used, and sintering was performed at varying temperatures (1270, 1280, and 1300 °C) and durations (60 and 120 min), followed by a furnace, air, and water cooling. An optimum hardness of ~970 HV was obtained when parts were sintered at 1270 °C for 60 min, followed by water quenching. Impressive compressive strength of ~ 3580 MPa was observed in the sample sintered at 1280 °C for 60 min duration, followed by air cooling. Furnace-cooled parts showed the highest density of ~95 %, whereas the relative density of air- and water-cooled parts varied between ~91 to 93.50 %, respectively. The microstructure of sintered samples revealed the formation of M 6 C stable carbide, M 2 C metastable carbide, MC as a secondary carbide, and a-Fe matrix, which contributed to the observed increase in mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Electronic, magnetic, and optical properties of bulk and (1 1 1)-surfaces of CoMnZnSi quaternary Heusler alloy

The structural stability, electronic structure, and magnetic and optical properties of CoMnZnSi quaternary Heusler alloy (QHA) in the bulk and (1 1 1)-slab forms have been investigated by performing density functional theory (DFT) calculations. Formation and cohesive energies, and elastic constants confirm that the bulk CoMnZnSi is chemically and mechanically stable at an equilibrium lattice parameter of 5.81 Å. The calculated elastic constants also indicate that this QHA has ductile and anisotropic features. We investigate and discuss the bonding behavior from charge density distribution and density of states. Furthermore, these calculations in the bulk phase show a perfect half-metallic behavior with an integer value of magnetic moment (4 µB) and a large spin-flip gap of 0.39 eV. On the other hand, the Co (1 1 1) and Si (1 1 1)-slabs exhibit semi-metallic nature at the Fermi level. These results indicate that CoMnZnSi qualifies for spintronic applications. In the bulk and Co (1 1 1), Zn (1 1 1), and Si (1 1 1)-surfaces, the magnetic moment of Co and Mn atoms are ferromagnetically aligned, while the ferrimagnetic alignment of Co with Mn has been found in Mn (1 1 1)-surface. We also investigate the optimal conductivity, dielectric functions, reflectivity, absorption coefficient, refractive index, and loss function to understand the underlying optical properties of this alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Electronic and magnetic properties of iridium-based novel Heusler alloys

We report half-metallicity and magnetism including exchange splitting are the most significant physical parameters to predict and design a candidate material for spintronic applications. We report here an ab-initio investigation on chemical formation and dynamical stability along with electronic structure and magnetic properties of Ir 2 Cr (Si, Ge) and IrRhCr (Si, Ge) Heusler alloys. The negative formation and cohesive energies with positive phonon dispersions confirm the stabilities of these alloys. Electronic structure calculations reveal that Ir 2 Cr (Si, Ge) and IrRhCrSi alloys are half-metallic ferromagnets with unprecedented exchange splitting. In addition, IrRhCrGe also shows semi-metallic nature. All of these materials follow Slater Pauling rule with large magnetic moments and 100% spin-polarization. With Cr bearing the majority of the local magnetic moment and exchange splitting, a ferromagnetic state is more stable than a nonmagnetic state. The electronic charge distribution and population analysis confirm mixed ionic and covalent bonding. The magnetocrystalline anisotropy energy, with the easy magnetization along the [1 1 1] direction, is significantly high in Ir 2 CrGe. Elastic constants such as shear (G), bulk (B), Young’s moduli, and Poisson’s ratio indicate that the IrRhCrSi and IrRhCrGe alloys are mechanically stable, and Ir 2 CrSi and Ir 2 CrGe are mechanically unstable. The Pugh’s (B/G) and Poisson’s ratios confirm that the stable alloys are ductile.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Decoupling the effects of texture and composition on magnetic properties of Fe-Si sheet processed by shear deformation

Soft magnetic Fe-Si alloys (electrical steels) possess exceptional functional properties such as high permeability, low coercivity, and low core loss, which generally improve with increasing Si content in the alloy. However, Fe-Si alloys containing > 3.5 wt% Si are also characterized by prohibitively low workability and poor ductility that have prevented their efficient commercial production in sheet form by rolling. This has limited their use for improving efficiency of motors and transformers. In this study, hybrid cutting-extrusion (HCE) is used as a single-step thermomechanical processing method to produce continuous Fe-Si alloy sheet with high Si compositions of 4 wt% to 6.5 wt%. HCE sheet is shown to have a homogeneous annealed grain structure and simple-shear crystallographic textures. By controlling the HCE deformation path, varied crystallographic shear textures are created in the sheet. Quasi-static magnetic properties of the HCE sheet are evaluated to decouple the effects of sheet texture and Si composition on resultant permeability and coercivity properties. The results suggest that HCE, with suitable process scaling, is a viable route for production of high-Si content electrical steel sheet for next-generation motors and transformers.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The effect of loading direction on the fracture behaviors of cortical bone at a dynamic loading rate

Here, the dynamic cracking processes in porcine cortical bone were visualized in real-time using the high-speed synchrotron X-ray phase-contrast imaging (PCI) technique in three osteon orientations: in-plane transverse, out-of-plane transverse and in-plane longitudinal. The dynamic flexural loading applied on the pre-notched bone specimens was introduced by a modified Kolsky compression bar. High-speed X-ray images of the entire loading events were documented with a high-speed camera. Three-dimensional X-ray micro-computed tomography was conducted to examine the intact microstructures and obtain the basic material properties of the bone material used for mechanical characterizations. The onset location, where crack initiated, and the subsequent direction, along which the incipient crack propagated, were measured quantitatively using the high-speed X-ray images and the latter was found dependent on the osteon direction significantly. The crack propagation velocities were dependent on crack extension over the entire crack path significantly for all the three directions while the initial velocity for in-plane longitudinal direction was lower than the other two directions. Straight-through crack paths were observed for in-plane longitudinal specimens while the cracks were deflected and twisted in the in-plane transverse direction. For out-of-plane transverse direction, the cracks follow paths with tortuosity fall in between the other two directions, showing a mixed mode of fractures of the former two extreme cases. The toughening mechanisms, visualized by the high-speed X-ray images, and the corresponding fracture toughness, evaluated in terms of fracture initiation toughness and crack growth resistance curve (R-curve), were also found significantly different among the three osteon directions, suggesting an overall transition from brittle to ductile-like fracture behaviors at the dynamic displacement rate (5.4 m/s) as the osteon orientation varies from in-plane longitudinal to out-of-plane transverse, and to in-plane transverse eventually.

42 ENGINEERING↗