SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A diffusive-thermal high Lewis number (Le) gas-phase oscillator has been observed in premixed flames using a lean mixture of butane and oxygen diluted with helium (Le approximately equals 3.0). This reactive-diffusive system exhibits both propagating radial pulsations and rotating spiral waves perhaps analogous to those observed in other excitable media such as the Belousov-Zhabotinsky reaction.
Premixed stoichiometric H2/O2/N2 flames propagating in two-dimensional turbulence were studied using direct numerical simulation (simulations in which all fluid and thermochemical scales are fully resolved) including realistic chemical kinetics and molecular transport. Results are compared with earlier zero-chemistry (flame sheet) and one-step chemistry simulations. Consistent with the simpler models, the turbulent flame with realistic chemistry aligns preferentially with extensive strain rates in the tangent plane and flame curvature probability density functions are close to symmetric with near-zero means. By contrast to simple-chemistry results with non-unity Lewis numbers (ratio of thermal to species diffusivity), local flame structure does not correlate with curvature but rather with tangential strain rate. Turbulent straining results in substantial thinning of the flame relative to the steady unstrained laminar case. Heat release and H2O2 contours remain thin and connected ('flamelet-like') while species including H-atom and OH are more diffuse. Peak OH concentration occurs well behind the peak heat-release zone. The feasibility of incorporating realistic chemistry into full turbulence simulations to address issues such as pollutant formation in hydrocarbon-air flames is suggested.
The use of heat conduction flame generated in a premixed supersonic stream is discussed. It is shown that the flame is controlled initially by heat conduction and then by chemical reaction. Such a flame is shorter than the diffusion type of flame and therefore it requires a much shorter burner. The mixing is obtained by injecting the hydrogen in the inlet. Then the inlet can be cooled by film cooling.
Ignition and propagation of turbulent flame front in jet flow investigated for combustible hydrogen- air mixture
Particulate matter (PM or soot) emissions generated by combustion of conventional and reformulated fuels adversely impact the environment and human health (Bond et al., 2013; Landrigan et al., 2018; World Health Organization (WHO), 2016), generating public awareness and motivating efforts towards the mitigation of their harmful effects. Soot formation is one of the most complex phenomena in combustion, involving interactions between combustion chemistry, fluid mechanics, mass/heat transport, and particle dynamics, spanning different spatial and temporal scales. A fundamental understanding of soot formation process is thus necessary to achieve a strong reduction of PM emissions and design cleaner and more efficient combustion systems. This has motivated a longstanding and ongoing research activity aimed at improving our understanding of the physical and chemical processes involved in soot formation, well reviewed in these recent works (Wang and Chung, 2019; Michelsen et al., 2020; Martin et al., 2022). Despite the wide interest, the transition from gas-phase molecules to incipient soot particles is still elusive and the successive particle growth and oxidation processes are far from being fully understood, especially in conditions relevant to real-world applications. Recent advances in combustion PM emission diagnostic and computational capabilities helped in improving the predictability of fundamental chemical and aerosol models for practical applications, thus tackling some of the above-mentioned challenges. The aim of this research topic is to display the ongoing research efforts in addressing the existing gaps on particulate formation from various fuel sources and in conditions typical of practical combustion applications (e.g. flames, engines, pool fires), through both experimental and numerical approaches.
A gas-fueled burner, the Burning Rate Emulator (BRE), is used to emulate condensed-phase fuel flames. The design has been validated to easily measure the burning behavior of condensed-phase fuels by igniting a controlled stream of gas fuel and diluent. Four properties, including the heat of combustion, the heat of gasification, the surface temperature, and the laminar smoke point, are assumed to be sufficient to define the steady burning rate of a condensed-phase fuel. The heat of gasification of the fuel is determined by measuring the heat flux and the fuel flow rate. Microgravity BRE tests in the NASA 5.2 s drop facility have examined the burning of pure methane and ethylene (pure and 50 in N2 balance). Fuel flow rates, chamber oxygen concentration and initial pressure have been varied. Two burner sizes, 25 and 50 mm respectively, are chosen to examine the nature of initial microgravity burning. The tests reveal bubble-like flames that increase within the 5.2s drop but the heat flux received from the flame appears to asymptotically approach steady state. Portions of the methane flames appear to locally detach and extinguish at center, while its shape remains fixed, but growing. The effective heat of gasification is computed from the final measured net heat flux and the fuel flow rate under the assumption of an achieved steady burning. Heat flux (or mass flux) and flame position are compared with stagnant layer burning theory. The analysis offers the prospect of more complete findings from future longer duration ISS experiments.
This short communication reports, for the first time, the existence of two different self-sustaining cool flame regimes of diethyl ether (DEE) in a diffusion counterflow burner: a weaker autoignition-assisted cool flame near the fuel burner and a normal diffusion cool flame near the stagnation plane. Here, the results show that the normal diffusion cool flame extinction limit increases monotonically with the fuel mole fraction, while the autoignition-assisted cool flame approaches a plateau and can exist at a fuel mole fraction below the normal diffusion cool flame. It is shown that both flame regimes are governed by the same low-temperature chain-branching reaction pathway of DEE. By using in situ laser diagnostics, entrainment of unburned fuel stream to oxygen stream at the outer edge of the fuel burner is identified as the governing physical mechanism causing a partially premixed self-sustained hollow cool flame structure. The results reveal that when a fuel with high low-temperature reactivity, two different cool flame regimes can be observed in a counterflow flame experiment. Future studies with high-reactivity fuels in a counterflow burner must ensure to distinguish between the two self-sustaining cool flame regimes. Moreover, the existence of these different cool flame regimes needs to be examined so that they would not trigger an uncontrolled combustion phasing in advanced engines fed with high low-temperature reactivity fuels.
Understanding the physical phenomena controlling the ignition and spread of flames in microgravity has importance for space safety as well as for characterizing dynamical and chemical combustion processes which are normally masked by buoyancy and other gravity-related effects. Unfortunately, combustion is highly complicated by fluid mechanical and chemical kinetic processes, requiring the use of numerical modeling to compare with carefully designed experiments. More sophisticated diagnostic methods are needed to provide the kind of quantitative data necessary to characterize the properties of microgravity combustion as well as provide accurate feedback to improve the predictive capabilities of the models. Diode lasers are a natural choice for use under the severe conditions of low gravity experiments. Reliable, simple solid state operation at low power satisfies the operational restrictions imposed by drop towers, aircraft and space-based studies. Modulation wavelength absorption spectroscopy (WMS) provides a means to make highly sensitive and quantitative measurements of local gas concentration and, in certain cases, temperature. With near-infrared diode lasers, detection of virtually all major combustion species with extremely rapid response time is possible in an inexpensive package. Advancements in near-infrared diode laser fabrication technology and concurrent development of optical fibers for these lasers led to their use in drop towers. Since near-infrared absorption line strengths for overtone and combination vibrational transitions are weaker than the mid-infrared fundamental bands, WMS techniques are applied to increase detection sensitivity and allow measurement of the major combustion gases. In the first microgravity species measurement, Silver et al. mounted a fiber-coupled laser at the top of the NASA 2.2-sec drop tower and piped the light through a single-mode fiber to the drop rig. A fiber splitter divided the light into eight channels that directed the laser beam across a methane or propane diffusion jet flame. The light beams were recaptured by a set of gradient index lenses, coupled back into separate fiber optic lines, and transmitted back to detectors and electronics in the instrument package. In these experiments a 6-mm od fiber cable (containing the nine optical fibers) fell with the drop rig. Using separate detection and demodulation channels, spatial and temporal (up to 20 Hz) maps of water vapor and methane concentrations were obtained at differing heights in the flames. While this apparatus was useful from a demonstration standpoint, several drawbacks needed attention before useful scientific measurements could be obtained. First, eight lines of sight are somewhat insufficient for detailing the spatial profiles of the gas. Second, multiple detection channels operating in parallel are both expensive and present a challenge for accurate calibration. As a result, a newer scanning system was developed in our first contract under this program. The primary characteristic of this system is that it contains a single detection channel and achieves "continuous" spatial resolution by scanning the laser beam across the flame region, then directing this beam onto a single detector. Thus spatial measurements are converted to a temporal series of data. The true spatial resolution is limited only by the beam diameter and width of the sweep. In these experiments the beam is focused to about 1-mm diameter and scans across a region up to 4-cm wide.
Triple flames arise in a number of practical configurations where fuel and oxidizer are partially premixed, such as in the base of a lifted jet flame. Past experimental studies, theoretical analyses, and numerical modeling of triple flames suggested the potential role of triple flames in stabilizing turbulent flames and in promoting flame propagation. From recent numerical simulations of laminar triple flames, a strong influence of differential diffusion among species and heat on the triple flame structure has been gradually appreciated. This paper reports preliminary numerical results on the influence of gravity and differential diffusion effects on the structure and dynamics of triple flames with a one-step global irreversible chemistry model.
Ignition temperatures of magnesium ribbon and aluminum wire samples electrically heated in argon-oxygen-carbon dioxide-water vapor mixtures
Hydrogen fire visualization detection techniques including application of photography, TV and image converter in IR and UV regions
Fluid dynamic model and diffusion-controlled flame analysis data on nonlinear combustion instability in liquid propellant rocket engines
The Kuramoto-Sivashinsky equation arises in a variety of applications, among which are modeling reaction diffusion systems, flame propagation and viscous flow problems. It is considered here, as a prototype to the larger class of generalized Burgers equations: those consist of a quadratic nonlinearity and an arbitrary linear parabolic part. It is shown that such equations are well posed, thus admitting a unique smooth solution, continuously dependent on its initial data. As an attractive alternative to standard energy methods, existence and stability are derived in this case, by patching in the large short time solutions without loss of derivatives.
The Kuramoto-Sivashinsky equation arises in a variety of applications, among which are modeling reaction diffusion systems, flame propagation and viscous flow problems. It is considered here, as a prototype to the larger class of generalized Burgers equations: those consist of a quadratic nonlinearity and an arbitrary linear parabolic part. It is shown that such equations are well posed, thus admitting a unique smooth solution, continuously dependent on its initial data. As an attractive alternative to standard energy methods, existence and stability are derived in this case, by patching in the large short time solutions without 'loss of derivatives'.
An investigation was conducted in the Lewis altitude wind tunnel to evaluate the performance and operational characteristics of the J40-WE-8 afterburner. A brief program of minor modifications to the flame holder, diffuser, and fuel system was undertaken to improve at a burner-inlet pressure level of 620 pounds per square foot. At this pressure level, modifications to the fuel system resulted in an increase in maximum net thrust from 1500 to 1600 pounds and a reduction in specific fuel consumption in the stoichiometric region from 3.70 to 3.15 pounds of fuel per hour per pound of net thrust. However, these fuel system modifications also resulted in buzzing combustion under certain operation conditions.
The infrared spectrum of the deuterated hydroxyl radical OD has been measured with a fourier transform spectrometer between 1850 and 9000 cm(sup -1).
Previous experiments have led to the hypothesis that pyrolysis of silica nanoparticle precursors carried in an inert central gas jet surrounded by a laminar flame is initiated not by thermal decomposition (the measured jet temperatures are too low for pyrolysis), but by reactions with H-atoms diffusing from the surrounding flame into the jet. The current work tests this hypothesis using femtosecond two-photon laser-induced fluorescence (fs-TPLIF) to image H-atom concentrations in the same flame configuration as the previous experiments. Methane flames (ϕ = 0.83, 1.01 and 1.13) were generated using a multi-element diffusion (Hencken) burner equipped with a central tube through which the N2 jet was introduced. The fs-TPLIF line imaging showed significant concentrations of H-atoms in the nitrogen jets at heights above the burner (HAB) close to the methane flame front. The measurements indicate radial diffusion of the H atoms from the flame to the jet is significant. The H-atom concentrations in the jet increased with increasing stoichiometry of the methane flame. Additional experiments were performed with hexamethyldisiloxane entrained in the central jet flow. In each case, a diffusion flame producing silica nanoparticles was established at the boundaries between the central jet and the methane flames. The 2D H-atom images showed a transition from over-ventilated diffusion flames to under-ventilated diffusion flames with increasing equivalence ratio. Furthermore, the fs-TPLIF profiles show a significant production of H-atoms within the jet when the surrounding flame is lean. This knowledge contributes to a deeper understanding of the underlying mechanisms governing these synthesis flame systems and opens avenues for advancing silica nanoparticle synthesis techniques.
Flat flame burners are valuable tools for studying complex combustion phenomena like particle synthesis due to the well-controlled and well-behaved initial and boundary conditions. In this study, the methane/air flame temperature and tracer density profiles of a multi-element diffusion burner equipped with a central tube were characterized using krypton (Kr) x-ray fluorescence at the Advanced Photon Source at Argonne National Laboratory. The experiments were performed using a fuel-to-oxygen equivalence ratio of 0.8 and 3.3% Kr by volume was added to the reactant gases. One- and two-dimensional scans of non-combusting (i.e., cold flow) and combusting conditions, both with and without flow through the central tube were performed. Spatially-resolved Kr number density profiles were obtained at different planar locations and heights above the surface of the burner. The results show rapid mixing occurred near the exit-plane of the burner and increased spatial uniformity was achieved from 0.1 mm to 0.5 mm above the surface of the burner. Further, the data also showed the impact of the central tube flow on the main methane/air flame, including evidence of the central tube flow mixing with the main flow. Flame temperatures were calculated from the fluorescence measurements at various heights above the burner surface and were in good agreement with model predictions for a burner stabilized flame. These high-fidelity measurements provide accurate baseline data that are particularly valuable for understanding the effects of fuel and air mixing on downstream phenomena, such as the formation of condensed-phase products.