Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Diffusion coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

Study of permeability characteristics of membranes

Pressure-permeation experiments were performed with the concentration-clamp cell. Streaming potentials and hydraulic permeabilities were measured for an AMF C-103 cation-exchange membrane bounded by 0.1 N NaCl solutions. The streaming potential calculated from the slope of the recorded potential differences versus the applied pressure, yields a value of 1.895 millivolt/dekabar. When comparison with other membranes of similar characteristics could be made, good agreement was found. The values of the hydraulic permeability varied somewhat with the applied pressure difference and are between 1.3 x 10 to the minus 8th power and 3.9 x 10 to the minus 8th power sq cm/dekabar-sec. The specific hydraulic permeabilities were also calculated and compared with data from the literature. Fair agreement was found. The diffusion coefficient of the chloride ion in the AMF C-103 membrane was calculated, using Fick's first law of diffusion based on ion concentrations calculated from the Donnan equilibrium concentration of Cl(-).

Spiegler, K. S.↗

The radial variation of solar flare proton anisotropies observed in deep space on Pioneers 10 and 11

The anisotropy of solar-flare protons (greater than 3 MeV) was evaluated at the time of maximum for each of 24 events measured by Pioneers 10 and 11 and was observed to decrease gradually between 1 and 4.7 AU. Since diffusive streaming is related directly to the effective diffusion coefficient parallel to the interplanetary spiral magnetic field, these observations provide a measure of the radial dependence of interplanetary diffusion parameters. Analysis of these results suggests that the spiral field increases gradually with heliocentric distance. An expression is given for the radial dependence of that field.

Mccarthy, J.↗

Numerical models of solar modulation of galactic cosmic rays, including drifts

Numerical solutions are presented of the steady-state modulation of galactic cosmic rays for a realistic two-dimensional model which includes drifts. Calculations of energy spectra and the spatial density variation of protons are shown for a model that incorporates the solar-minimum magnetic field and nominal interplanetary propagation parameters. The calculated values are relatively insensitive to the assumed size of the modulating region and to the magnitude of the particle diffusion coefficient. The solutions show a broad interior 'plateau' in which radial gradients are small. A simple model that neglects diffusion but includes drifts and adiabatic cooling accounts for these results. It is concluded that in this model and the range of parameters, diffusion plays a role secondary to that of drifts and adiabatic cooling.

Jokipii, J. R.↗

Nonequilibrium ionization due to thermal diffusion and mass flows

Recent calculations of diffusion coefficients are used in the continuity equation to compute ion populations of carbon in the solar transition region. Thermal diffusion causes strong departures from ionization equilibrium in the region where the temperature gradient is steepest. Mass-conserving flows are also included in our calculations. These dominate over thermal diffusion depending on the magnitude of the flows and also lead to departures from ionization equilibrium. These results have important implications for the interpretation of EUV line emission.

Roussel-Dupre, R.↗

Anomalous plasma diffusion and the magnetopause boundary layer

An overview of the current state of anomalous diffusion research at the magnetopause and its role in the formation of the magnetopause boundary layer is presented. Plasma wave measurements in the boundary layer indicate that most of the relevant unstable wave modes contribute negligibly to the diffusion process at the magnetopause under magnetically undisturbed northward IMF conditions. The most promising instability is the lower hybrid drift instability, which may yield diffusion coefficients of the right order if the highest measured wave intensities are assumed. It is concluded that global stationary diffusion due to wave-particle interactions does not take place at the magnetopause. Microscopic wave-particle interaction and anomalous diffusion may contribute to locally break the MD frozen-in conditions and help in transporting large amounts of magnetosheath plasma across the magnetospheric boundary.

Treumann, Rudolf A.↗

A quantitative model of plasma in Neptune's magnetosphere

A model encompassing plasma transport and energy processes is applied to Neptune's magnetosphere. Starting with profiles of the neutral densities and the electron temperature, the model calculates the plasma density and ion temperature profiles. Good agreement between model results and observations is obtained for a neutral source of 5 x 10 exp 25/s if the diffusion coefficient is 10 exp -8 L3R(N)/2s, plasma is lost at a rate 1/3 that of the strong diffusion rate, and plasma subcorotates in the region outside Triton.

Richardson, John D.↗

Diffusion of Chromium in Alpha Cobalt-Chromium Solid Solutions

Diffusion of chromium in cobalt-chromium solid solutions was investigated in the range 0 to 40 atomic percent at temperatures of 1360 degrees, 1300 degrees, 1150 degrees, and 10000 degrees c. The diffusion coefficients were found to be relatively constant within the composition range covered by each specimen. The activation heat of diffusion was determined to be 63,000 calories per mole. This value agrees closely with the value of 63,400 calories per mole calculated by means of the Dushman-Langmuir equation.

Weeton, John W↗

Loss of solar He and Ne from IDPS in subducting sediment: Diffusion and the effect of phase changes

The results of the diffusion experiment for solar He and Ne in IDP's in a magnetic separate from Pacific Ocean sediment suggest that solar He and Ne would be easily released from IDP grains and hence lost from subducting slabs at shallow depths. However, since the diffusion experiments was conducted under high vacuum, there may be a possibility that magnetite grains, which are supposedly the main constituent of the magnetic fraction, might be partly reduced to form a metal phase due to low oxygen fugacity in the experimental condition. If this is the case, such a phase change might affect the gas release and hence the results of the diffusion coefficients. In order to examine whether or not such a phase change really occurred in the condition of the diffusion experiment, I conducted a heating experiment for a magnetic separate from Pacific Ocean sediment. In the same condition as in the diffusion experiment, and the run products were examined with an x ray diffraction method. Three samples were prepared: they were wrapped with platinum foil, put in a vacuum line, and heated in a molybdenum crucible for two hours at 500 C, 800 C,and 950 C, respectively. After cooling the furnace, the samples were taken out from the crucible and analyzed with an x ray diffraction method.

Hiyagon, H.↗

Se diffusion in CdTe thin films for photovoltaics

Manipulating CdSeTe bandgrading to enhance photocurrent and carrier lifetime is an essential part of high-performance CdTe photovoltaics (PVs). Here, we examine Se diffusion kinetics in single-crystal and polycrystalline CdTe during deposition, thermal annealing, and CdCl 2 treatments. Se distributions are determined by dynamic secondary-ion-mass spectroscopy and Auger electron spectroscopy depth profiling and coupled with electron backscatter diffraction images of the crystalline structure. Effective bulk and grain boundary diffusion coefficients are determined by analytical models and discussed in the context of processing and film morphology. Se is found to diffuse in CdTe at much higher rates during CdCl 2 treatments than with thermal processing alone. GB diffusion also occurs at a significantly faster rate than bulk diffusion. As a result of these two effects, the near interface bulk and GB Se diffusion during CdCl 2 treatments dominates the bandgrading profiles in CdTe PVs.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Photocarrier dynamics at the interface between WS 2 and ozone-irradiated graphene

We investigate the photocarrier properties of heterostructures (HSs) formed by WS 2 and ozone-irradiated graphene (OI-graphene), with a focus on the impact of ozone irradiation. Photoluminescence and Raman spectroscopy reveal a pronounced doping effect induced by ozone irradiation on the graphene layer. Transient absorption measurements demonstrate a substantial suppression of charge transfer efficiency across the interface in the presence of ozone molecules. Spatially resolved pump-probe measurements further show a significant reduction in the diffusion coefficient of photocarriers in WS 2 on OI-graphene compared to that of individual WS 2 monolayers. The slower diffusion suggests enhanced spatial separation of electrons and holes in the WS 2 layer, induced by a built-in electric field at the interface. This effect arises from the combined influences of doping and dielectric property changes caused by ozone molecules. These findings highlight the critical influence of ozone irradiation on graphene and HS interfaces, offering valuable insights for the design of future graphene-based two-dimensional HSs.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Solubility and diffusion of hydrogen in IN-100 and Waspaloy

The solubility of hydrogen, at a fixed hydrogen pressure, was measured in two different heat treatment conditions in both IN-100 and Waspaloy by equilibrium and analysis. The diffusion coefficients were determined by measuring the rate of hydrogen evolution in a vacuum. Hydrogen evolution appeared to be a diffusion-controlled process in all cases. For hydrogen diffusion in Waspaloy, Delta H was 38.5 kJ and D0 was 2.6 x 10 to the -7th sq/s. For IN-100, Delta H was 68.2 kJ and D0 was 59 x 10 to the -7th sq/s. The values for Waspaloy are close to those for pure nickel. The values for IN-100 are more similar to high nickel alloys that show trapping or surface layer impedance.

Khan, A. S.↗

Oxygen tracer diffusion in single-crystal alumina

Oxygen tracer diffusion coefficients are determined in single-crystal alumina samples with differing dopant levels using the gas-exchange technique. The diffusion direction is parallel to the c-axis and the ambient PO2 is 1 atm (100,000 Pa) for all experiments except a single run with a low PO2, approximately 10 to the -15th atm (10 to the -10th Pa) produced by a CO/CO2 mixture. The diffusion is insensitive to both impurities and ambient PO2. The insensitivities are discussed in terms of point-defect clustering. Prior tracer studies are compared and discussed.

Cawley, James D.↗

Strain-Rate-Free Diffusion Flames: Initiation, Properties, and Quenching

For about a half century, the stabilization of a steady planar deflagration on a heat-sink-type flat-flame burner has been of extraordinary service for the theoretical modeling and diagnostic probing of combusting gaseous mixtures. However, most engineering devices and most unwanted fire involve the burning of initially unmixed reactants. The most vigorous burning of initially separated gaseous fuel and oxidizer is the diffusion flame. In this useful idealization (limiting case), the reactants are converted to product at a mathematically thin interface, so no interpenetration of fuel and oxidizer occurs. This limit is of practical importance because it often characterizes the condition of optimal performance (and sometimes environmentally objectionable operation) of a combustor. A steady planar diffusion flame is most closely approached in the laboratory in the counterflow apparatus. The utility of this simple-strain-rate flow for the modeling and probing of diffusion flames was noted by Pandya and Weinberg 35 years ago, though only in the last decade or so has its use become internationally common place. However, typically, as the strain rate a is reduced below about 20 cm(exp -1), and the diffusion-flame limit (reaction rate much faster than the flow rate) is approached, the burning is observed to become unstable in earth gravity. The advantageous steady planar flow is not available in the diffusion-flame limit in earth gravity. This is unfortunate because the typical spatial scale in a counterflow is (k/a)(sup 1/2), where k denotes a characteristic diffusion coefficient; thus, the length scale becomes large, and the reacting flow is particularly amenable to diagnostic probing, as the diffusion-flame limit is approached. The disruption of planar symmetry is owing the fact that, as the strain rate a decreases, the residence time (l/a) of the throughput in the counterflow burner increases. Observationally, when the residence time exceeds about 50 msec, the inevitably present convective (Rayleigh-Benard) instabilities, associated with hot-under-cold (flame-under-fresh-reactant) stratification of fluid in a gravitational field, have time to grow to finite amplitude during transit of the burner.

Fendell, Francis↗

Polymer Conformations and Diffusion Through a Monolayer of Confining Nanoparticles

We present coarse-grained molecular dynamics simulations to probe chain-scale polymer conformations and diffusion between confining nanoparticles (NPs). By constructing a monolayer of hexagonally-packed NPs in a polymer melt with athermal interactions, we observe the magnitude and length-scale over which homogeneously confining NPs impact the polymer behavior, which provides fundamental insights into more complex polymer nanocomposites. We show that polymer conformations are more perturbed under strong confinement (i.e. when the interparticle distance, ID, is less than twice the polymer radius of gyration, 2R g ) as compared to around an isolated NP, and the effect depends on the ratio of R NP /R g rather than either independently. In fact, these conformations can be quantitatively replicated by executing a simple random walk in a similarly confining environment. We also show that polymer diffusion is slowed by the presence of NPs and the slowing persists far beyond the length-scale over which polymer conformations are perturbed. Although the slowing is strongest ~R g from the NPs, the diffusion coefficient is slower even beyond ~5R g from the NPs. Furthermore, by analyzing the directional van Hove distributions, we show polymer diffusion away from the NP monolayer is bulk-like while diffusion through the monolayer is slower with increasing NP confinement. Furthermore, these molecular dynamics simulations provide fundamental insights into the temporal and spatial effect of confining, athermal NPs on chain-scale polymer conformations and diffusion.

36 MATERIALS SCIENCE↗

Modeling the Effects of Drift Orbit Bifurcation on Radiation Belt Electrons

Abstract Drift orbit bifurcation (DOB) has been suggested to play a major role in the loss and transport of radiation belt electrons since it violates the second adiabatic invariants of particles and makes the third invariant undefined. Results from our guiding‐center test particle simulations using the Tsyganenko‐1989c magnetic field model show that the DOB could affect a broad region of the outer radiation belt, which can penetrate inside the geosynchronous orbit at Kp ≥ 3, and its effects are more significant further away from the Earth, at a higher Kp and for higher electron energies. Specifically, the short‐term simulation results after one electron drift show both traditional and nontraditional DOB transport of electrons, with the nontraditional DOB, caused by a third minimum of the magnetic field strength near the equator, reported here for the first time. Moreover, our results show large ballistic jumps in the second invariant and radial distance for electrons at high equatorial pitch angles after one drift. In addition, long‐term DOB transport coefficients of electrons over many drifts are calculated based on our simulation results. We find that the pitch angle and radial diffusion coefficients of electrons due to DOB could be comparable to or even larger than those caused by electron interactions with chorus and Ultra‐Low‐Frequency waves, respectively. In sum, our results demonstrate that DOB could cause effective loss and transport of radiation belt electrons even in the absence of waves.

Astronomy & Astrophysics↗

Ab Initio Insights to Metal Passivation: Diffusion and Defect Formation in Amorphous Zirconia and Alumina

Metal passivation refers to the formation of protective oxide films on metals, which shield them from further corrosion and oxidation, playing a crucial role in maintaining their stability. The mesoscopic Point Defect Model has successfully predicted passivity as a steady state process where oxide growth from oxygen vacancies at the metal/film interface competes with oxide dissolution at the film/environment interface. In this work, informed by the Point Defect Model parameters, we use first-principles calculations to calculate defect formation and atomic diffusion in amorphous materials and correlate these descriptors with the behavior and growth of the oxide film. Focusing on amorphous zirconia and alumina, we demonstrate that defect formation energies exhibit significant variability in amorphous systems. In alumina, vacancies dominate, with cation and anion vacancies occurring at comparable concentrations. Diffusion calculations for stoichiometric amorphous alumina and zirconia, as well as oxygen-deficient zirconia, reveal faster diffusion in the oxygen-deficient case, highlighting the impact of defects on transport. Comparison of calculated self-diffusion coefficients for the dominant defect species with experimentally measured oxide thicknesses shows a clear correlation, suggesting that first-principles-derived diffusivity information can serve as a key descriptor for surface passivation film growth.

Farnell, Mackinzie S. [University of California, B↗

The problem of cooling the cold Io torus

Two models are developed for the transport of ions inward from Io's orbit, the first using the assumption that radial diffusion is the dominant transport mechanism while the second uses a combination of diffusive and convective transport. The models include thermal and number density transport, radiation, ionization and pickup of local neutrals, recombination, charge exchange, and Coulomb interactions. It is found that pure diffusive transport can account for the dramatic inward depletion of the torus only by invoking recombination or by postulating a massive increase in the production rate of torus ions sometime prior to the Voyager mission. Recombination is determined to be far too slow to be the cause of the observed density decrease inside of Io. The model combining convection and diffusion is shown to reasonably match the data, but only if a diffusion coefficient 100 times less than that derived from Pioneer observations is used. In addition, it is shown that the Pioneer derived diffusion rate combined with Voyager temperature and density measurements indicate a large nonradiative sink of energy in the inner torus.

Richardson, J. D.↗